Whac A Mole FEC Manual
Contents
1. GROUP GAME OPERATION MANUAL WARNING Be sure to read this Operation Manual before using your machine to ensure safe operation 2010 Bob s Space Racers Incorporated 427 15 STREET DAYTONA BEACH FLORIDA 7 PHONE 386 677 0761 31 BOBSSPACERACERS COM November 2010 2010 BOB S SPACE RACERS INC BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 Federal Communications Commission FCC Statement Note This equipment has been tested and found to comply with limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his her own expense gt WARNING ALL OF BOB S SPACE RACERS GAMES ARE SHIPPED WITH THE SAME KEY AND LOCK SETS IT IS IN YOUR BEST INTEREST TO CHANGE THE KEYS AND LOCKS ON YOUR GAMES WHEN YOU RECEIVE THEM 10 11 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 TABLE O2. FEC MANUAL BSR V1 0 13 Reassembly the washers Note the correct order 14 Return the coil bed assembly to the game Snap the clip back in place Plug in the Molex plug connectors Repeat these steps for each of the Mole Head shafts 15 Secure the coil bed assembly to the unit using 16 Return the playfield area to the unit and attach the 2 the 4 bolts and washers 21 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 9 PARTS LIST TBD 22 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 10 TROUBLESHOOTING WARNING For your safety and to reduce risk of damage to your game read the Important Safety Information in Chapter 2 2 before attempting any troubleshooting procedure TROUBLESHOOTING PHILOSOPHY When troubleshooting any product certain general guidelines should be followed 1 Always check to be sure that your game is turned on Be sure that all of the fuses in the game are functional and check to see that the AC voltage is in the proper operating range for your game 2 Check to be sure that all of the game harnessing Is plugged in properly and that all of the pins are firmly seated in the connectors It is always possible that a harness can be damaged by rough shipping or moving 3 Check game harnessing to be sure that none of the wires have become or are damaged Using a handheld multi meter check continuity of the wires to make sure they are not broken 4 Check for o
3. the original purchaser must pay all freight shipping or transportation charges for the return of the equipment from Bob s Space Racers Inc to the original purchaser Telephone or write 32 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 WHEN CALLING FOR SERVICE 1 When calling for service please check the service manual first Many times the answer to your problem has been addressed in this documentation 2 Please make sure you have the serial number of the game ready when you call 3 If this is a repeat call please tell the service technician that you have made a previous call regarding this problem This way we will be able to retrieve the history on your game allowing us to serve you better and save you time 4 Please retain proof of purchase for your product This might be requested for warranty repairs 5 Please call from the game if possible since we might need you to check certain things on the game while we are on the telephone with you IF YOU HAVE ANY QUESTIONS OR COMMENTS PLEASE CALL OUR SERVICE DEPARTMENT AT 386 677 0761 MONDAY FRIDAY 8 30AM 5 00PM EST EXCLUDING HOLIDAYS or EMAIL QUESTIONS Tech BobsSpaceRacers com or VISIT THE CUSTOMER SUPPORT SECTION ON OUR WEBSITE WWW BOBSSPACERACERS COM 33
4. V1 0 SCORE SENSOR REPLACEMENT 1 Remove coil bed as indicated above in the coil bed removal and installation section 2 Unplug and unscrew the defective sensor pair and replace 3 Assemble in the reverse order SOLENOID REPLACEMENT COIL BED FRONT VIEW 1 Remove coil bed as indicated above in the coil bed removal and installation section 2 Remove the associated Mole head as indicated in the mole head removal PHIMSER section I BEARING 3 Remove the 2 1 4 20 hex head bolts that hold the solenoid plunger bearing into the top of the coil bed assembly 4 Unplug the bad solenoid and remove from the coil bed assembly 5 Install the new solenoid making sure that the wires come out of the TOP of the solenoid and feed back down into the coil bed There is a clearance notch in the top of the coil bed assembly for the solenoid wires COIL BED SECTION VIEW MARQUEE DISPLAY AND FLORESCENT BULB BALLAST REPLACEMENT 1 Turn off A C power to the game and unplug the game from the A C receptacle 2 Remove the 8 screws that hold the marquee cover graphics to the marquee 3 Remove the graphics panel FRONT VIEW 28 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 SCORE DISPLAY REMOVAL 1 Remove the 4 hex nuts from the back of the score display 2 Remove the score display from the marquee 3 Remove the ribbon cable from the bad display 4 Remove the 12 screws and th
5. WARRANTIES Unless modified in writing and signed by both parties this agreement is understood to be the complete and exclusive agreement between the parties superseding all prior agreements oral or written and all other communications between the parties relating to the subject matter of this agreement No employee or representative of Bob s Space Racers Inc or any other party is authorized to make any other warranty or to assume any other liability in connection with the sale of its equipment 6 TIME LIMIT FOR CLAIMS Any claim for breach of warranty or claims under this warranty must be received in writing by Bob s Space Racers Inc within 120 days following delivery of the equipment 7 FUTURE CHANGES Bob s Space Racers Inc reserves the right to reserve change or modify the construction and design of its equipment or any component part or parts thereof without incurring the obligations to make such changes or modifications in present equipment 8 ALLOCATION OF RISKS This agreement allocates the risks of equipment failure between Bob s Space Racers Inc and the original purchaser This allocation is recognized by both parties and is reflected in the price of the goods THE PURCHASER ACKNOWLEDGES THAT HE HAS READ THIS AGREEMENT UNDERSTANDS IT AND IS BOUND BY ITS TERMS 9 TO OBTAIN WARRANTY SERVICE The original purchaser must at his her own expense bring or ship the equipment to an authorized location for service Additionally
6. ticket debris off of all the optical sensors Clean Mole Shafts Regularly See Section 4 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 8 3 Test Mode Sensor and Coin Test Mode e With the game power on press the Program button on the Panel Programming Assembly This will take you into programming mode In this mode use the Select button to toggle between mode options see O chart page 11 of this manual The Set button on the unit change the settings in each mode The Set button will increment the value each time it is pressed until the values reach zero e While in programming mode Manually pull up the mole heads and you hear the mole sounds then the sensor is working correctly Manually press the coin switch and if you hear a coin sound then the switch is working correctly e After the desired changes are made to the programming options press and hold the Program button on the unit This will restart the game in game play mode with the desired changes updated into the game play Error Codes If 8 displayed on the center display there are no tickets in the ticket dispenser e Ifthe codes 810 820 830 840 or 850 are displayed on the center display there is a sensor failure located underneath of the mole box These are the mole head scoring sensors See picture below for corresponding positions of sensors and error codes 840 Top of game unit 16 BOB S SPACE RACERS Inc W
7. to do so could result in serious injury to yourself or others POWER SUPPLY SERVICING 1 Turn off A C power to the game and unplug the game from the A C receptacle 2 Remove coil bed as indicated above in the coil bed removal and installation section 3 Remove whichever power supply is faulty and replace 4 Assemble in reverse order TOP VIEW MAIN P C BOARD SOUND BOARD FUSE AND RELAY SERVICING 1 Turn off A C power to the game and unplug the game from the A C receptacle 2 Remove the 2 bolts that attach the playfield to the top of the main cabinet 3 Lift out and remove the playfield support frame from on top of the coil bed TOP VIEW 4 Replace the damaged board or bad fuse 5 Assemble in reverse order NOTE IF THE SOLENOID IS INSTALLED UPSIDE A LARGE LOSS OF SOLENOID STRENGTH WILL BE NOTED INSTALLING THE SOLENOID UPSIDE DOWN MAY ALSO RESULT IN SOLENOID WIRE DAMAGE 6 Re install the solenoid plunger bearing making sure that the anti rotation roll pin engages the notch in the top of the solenoid 7 Re install the bearing retaining bolts NOTE INSTALL THE BOLTS EVENLY AND DO NOT OVERTIGHTEN IF THE BOLTS ARE TIGHTENED UNEVENLY SOLENOID PLUNGER SHAFT BINDING MAY OCCUR 8 Re assemble the rest of the game in reverse order Refer to the specific sections of the manual if necessary 9 Plug the game in and test for smooth solenoid operation 27 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR
8. C wall receptacle when servicing this product Failure to do so could result in serious injury to yourself or others Use only a GROUNDED AC receptacle Failure to do so could result in improper operation or damage to the game and could void your warranty If you are unsure that your AC receptacle is properly grounded have a qualified electrician perform this check for you Always be sure power to the game is turned off when doing even routine maintenance Otherwise moving parts could activate unexpectedly and cause injury This product is heavy as necessitated by the design When moving this game be sure you have adequate help Use a Suitable dolly or hand truck where practical Use back support when needed 2 3 SET UP 1 Be sure that the game is on a level surface If the game is rocking on the floor use suitable shims to remove the rocking of the game 2 Be sure to plug the game into the proper A C GROUNDED receptacle Do not use long extension cords unless absolutely necessary and if so be sure it is a heavy duty cord of at least 16 Ga and no longer than 20 ft Check the label on the back of the game to make sure the power requirements of the game match that of your location 3 Turn the game on and check to be sure there are no unusual sounds and that everything appears to be working correctly When you first turn the game on you will notice all of the moles taking turns popping up out of their holes This is part of the diagnostic s
9. COIL BED REMOVAL AND INSTALLATION Turn off A C power to the game PLAYFIELD 2 Remove the 2 bolts that attach the playfield to the top of the main cabinet BOLTS PLAYFIELD SUPPORT 3 Lift out and remove the playfield FRAME support frame from on top of the coil bed 4 Remove the 4 bolts and washers that secure the coil bed to the cabinet o Remove the coil bed by grabbing onto the Mole heads and lifting up FRONT VIEW TOP VIEW 6 As you pull the coil bed out of the game be careful to unplug the 2 harnesses on the bottom of the coil bed 7 Assemble in the reverse order MOLE HEAD REMOVAL 1 Remove coil bed as indicated above in the coil bed removal and installation section 2 Remove the retaining clip from the bottom of the solenoid shaft RUBBER WASHER 3 Remove the plastic and rubber washers PLASTIC WASHER SOLENOID NOTE WHICH WAY THE WASHERS ARE INSTALLED BEFORE REMOVAL 4 Extract the shaft from the solenoid body SI PLASTIC WASHER 5 Remove the anti rotation guide from the shaft RETAINING CLIP 6 When installing a new Mole head be sure that the anti rotation guide is lined up to make the head straight when installed in the game 7 Assemble in reverse order 26 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 ELECTRONIC ELECTRICAL REPAIR WARNING Unplug the game from the AC wall receptacle when servicing this product Failure
10. F CONTENTS SPECIFICATIONS INTRODUCTION 2 1 Overview 2 2 Important Safety Information 2 3 Set Up PACKAGE CONTENTS INSTALLATION 4 1 Installation 4 2 Play zone Operation Zone 4 3 Locations to avoid 4 4 Game leveling CONNECTING THE POWER CORD INSTRUCTION FOR PLAY OPTION SETTINGS 7 1 Setting Options MAINTENANCE AND INSPECTION 8 1 Maintenance 8 2 Cleaning 8 3 Test Mode 8 4 Service PARTS LIST TBD TROUBLESHOOTING WARRANTY 22 23 32 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 1 SPECIFICATIONS wor C DIM HEIGHT B DIM WIDTH NOTE Game parameters are subject to change without notice BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 2 INTRODUCTION 2 1 Overview Thank you for purchasing the new Whac A Mole pro from Bob s space Racers Built on a long tradition of quality and value the new pro version Whac A Mole retains all of the great game play of the original game yet is specifically designed for today s Arcade environment New electronics technology was developed to maximize operation and revamp this arcade classic FEATURES NEW SOLENOID OPERATION The new solenoid design uses a heavy duty steel encapsulated high temperature bobbin developed specifically for this game The free floating mounting system assures long life for the integral brass sleeve as well as the Annealed Chrome mole solenoid shafts
11. Game will not start Game power off Faulty or unplugged sensor pair Main fuse blown Ground wire broken or loose Moles not working properly Faulty 12 volt power supply Faulty Front Panel Board Faulty Main P C Board or component Game stops or is stopped The power connector is disconnected with nothing displayed circuit The game could have a bad connection or short Mole heads won t pop up Excessive dirt or debris on solenoid shaft Solenoid shaft alignment Faulty sensor pair The current is too low Faulty 36 volt power supply Faulty solenoid coil Faulty main P C board or component Mole head will not score Disconnected sensor Faulty Connector or Connections Dirty Sensor Faulty Sensor Noisy mole heads when The shaft has loosened and needs tighten they move up and down The mole shaft could be bent Light bulbs are out Lamps are burnt out Possible faulty socket connection Faulty ticket dispenser harnessing Faulty main PC board 24 Faulty sound board or sound board harnessing Check Volume Control and adjust as necessary Check connections and or repair harnessing Check and or replace speaker Check S ates or r Replace Sound Board See Da SC ril n C W J 72 LIC Y IJCIU VV j Check diode Or replace Main P C Board Re bend coin switch wire Clean and adjust mech as necessary Check and or replace switch Check and or repair harnessing Reprogram or replace e
12. HAC A MOLE FEC MANUAL BSR V1 0 8 4 SERVICE COIL BED SERVICING The coil bed is the assembly that houses the solenoids score sensors and Whac A Mole heads This unit is built as an assembly to make servicing and repair easy The entire unit removes from the game as a sub assembly in just a couple of minutes SHAFT CLEANING Procedure 1 A quick fix for a Shaft that is sluggish Procedure 2 Cleaning Shafts without removing them from the game unit This procedure should be performed every 2 weeks Procedure 3 Removing Whac A Mole Heads for cleaning This procedure should be performed every 3 months or less if required Procedure 1 Instructions A quick fix for a Shaft that is sluggish Spray the Shaft with an all purpose Silicone Lubricant Note Do not use graphite spray It is conductive and you could short out the electrical wiring and or the Printed Circuit Board PCB BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 Procedure 2 Instructions Cleaning Mole Head Shafts without removing them from the game unit 1 Open the front of the game unit for access 2 Remove the clip using a short flathead 3 Remove the washers from the shaft screwdriver 5 Remove the 3 washers from the top of the shaft 6 Clean the shaft using a soft cloth 7 Reassemble the shaft in the reverse order Use an electrical contact anti corrosion cleaner such as ElectriCorr VPCL 239 or equivalent Polis
13. Technical Support is available whenever you should need it The direct technical hot line is 386 677 0761 Office hours are from 8 30 am to 5 00 pm EST Monday through Friday excluding holidays During all other times follow the prompts on our Automated Phone System to relay your problem to the technician on call Technical Support will assist you in troubleshooting a service problem or setting equipment options Customer Service hours are from 8 30 am to 5 00 pm EST Monday through Friday excluding holidays Customer Service staff can be reached at 386 677 0761 They will also take parts orders and research the status of previous orders As always you can call 386 677 0761 to reach all other departments or you can FAX anyone at BOB S SPACE RACERS by calling 386 677 0794 24 hours a day You can also e mail us at tech bobsspaceracers com 24 hours a day 30 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 ADVANCED REPLACEMENT POLICY After speaking with our Technical Department it may be necessary for Bob s Space Racers Inc to ship an assembly item or part to repair your game We will ship the item s according to your preference via United Parcel Service Federal Express US Postal Service etceteras Note we will not ship anything to P O Boxes via the US Postal Service You will be billed per your account status for the total cost of the shipment which includes shipping charges Upon shipment o
14. This design eliminates the air compressor pistons and associated parts of the original design This results in a lower cost simpler and quieter design that is specifically tailored to the Arcade environment CABINET DESIGN The new cabinet is designed to be lighter to make it easier to handle It also incorporates a new marquee design that is fully back lit to attract players from across the room New exciting graphics including a cute looking updated mole design to complete the package ELECTRONICS The game utilizes all solid state circuitry for the ultimate in reliability PROGRAMMING the game has extensive programming options available to customize the game to your location SELF DIAGNOSTICS The game checks itself at power up to be sure that all of the solenoids and associated sensors and switches are functioning properly If a failure is discovered the game will display the problem on the score LED s GAME PLAY The game play is the same great play that generations have been entertained by Hit those moles when they pop out of the holes The faster you get the faster they get There is a special reward for getting the high score The score high score of the day and bonus ticket amounts are indicated on the scoreboard The game plays until time runs out BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 GAME SET UP OPERATION AND MAINTENANCE 2 2 IMPORTANT SAFETY INFORMATION WARNING Unplug the game from the A
15. bvious damage to the P C Boards or electrical components 5 If you have multiple games or multiple parts on a game change or exchange the parts and see if the problem goes away or moves to another location This way you can quickly eliminate certain parts as being the problem with the game 6 When changing electronic or electrical components ALWAYS turn off and unplug the game 7 Check to see that all power supplies are delivering the specified voltages to the P C Boards and components as shown in the manual 23 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 Symptom Possible Problem Solution Power J Powr Sound Problems Low Volume No sound Faulty speaker harnessing Low Sound Intermittent Sound Faulty speaker Faulty Main P C Board Game does not take or add Coin switch out of adjustment money correctly Coin mech dirty or improperly adjusted Faulty Coin switch Faulty coin switch harness or connector Improperly programmed electronic mech Game improperly programmed Faulty Front Panel Board Faulty Main P C Board or component Ticket Dispenser not No tickets in the game working properly or no Tickets jammed in dispenser tickets being dispensed Ticket dispenser sensor blocked with debris Poor connection on the ticket dispenser Game improperly programmed Faulty ticket dispenser Faulty ticket dispenser harnessing Faulty Front Panel Board Faulty main PC board
16. e Locations subject to rain or water leakage e Unstable locations or locations subject to vibration e Dusty hot or damp locations BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 4 4 Game Leveling Install this machine on a flat surface Adjust levelers to lift the legs and level game Make sure that the machine is level with the floor If the machine is not level the game may not play well eveler Adjust 4 MIDE Fix 1 WARNING e Disconnect game power before moving e When moving the game DO NOT slide the game across the floor e Ensure the game is level before connecting the power BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 5 CONNECTING THE POWER CORD 1 Insert the socket end of power cord into the power input of the game 2 Insert the power cord plug into a service outlet 1 WARNING e Do not put heavy items on power cord e Hold the power plug instead of the wire to draw the power cord out of the socket YW Do not touch the power plug with wet hands BA Do not draw or twist the cord or near a heat source e Do not place the cord where the player can easily trip over or come in contact with it e Operate this game with the correct power and fuse configuration The machine s operating supply Voltage is 110VAC please refer to the label on the machine Improper voltage hookup may damage the machine and may cause an electrical shock to an ope
17. e plastic back from the back of the score display 3 Remove the 4 hex standoffs that hold the board to the mounting bracket SCORE DISPLAY 4 Assemble in reverse order SIDE VIEW NOTE BE CAREFUL TO PLUG THE RIBBON CABLE IN PROPERLY TO ASSURE PROPER FUNCTION AND TO AVOID DAMAGE TO THE BOARD BULB FLORESCENT BULB REPLACEMENT BUTTON 1 Remove the retaining clip that secures the bulb to the standoff RETAINING 2 Press the RED lock button of the fixture to release the bulb CLIP 3 Replace the bulb in reverse order NOTE BE SURE THAT THE NEW BULB IS PROPERLY SNAPPED INTO THE HOUSING TO AVOID IT COMING OUT FROM THE VIBRATION OF NORMAL GAME PLAY ALSO BE SURE THAT THE RETAINING CLIP IS SECURELY SNAPPED TO THE STANDOFF FRONT VIEW MARQUEE NOT SHOWN FLORESCENT BALLAST REPLACEMENT 1 Remove the florescent bulb and the retaining clip 2 Unscrew the bulb socket from the rear of the cabinet by removing the 2 screws 3 Unplug the ballast and remove the 2 screws that hold it to the rear of BALLAST the cabinet RETAINING 4 Carefully remove the wires from the bulb socket CLIP 5 Assemble in reverse order 29 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 SERVICE POLICY At BOB S SPACE RACERS INC our strength lies in the high quality long lasting equipment we manufacture Should the need arise we maintain both Technical Support and Customer Service staff
18. elf test BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 3 PACKAGE CONTENTS Be sure to check that you have received all packages indicated below 1 Game Unit 2 Accessories NAME SPECIFICATION Power cord 10A 250V 10 feet Part 0027145 Manual on ILLUSTRATION NOTE Wrapped up inside coin box In a bag in the games ticket holder Deltronic Coin Mechanism 0 e 1 Coin Box BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 4 INSTALLATION ATTENTION eFor indoor use only 4 1 Installation Check the parts list before installation Verify that all parts that have been received and are in good condition 4 2 Play zone Operation Zone This machine requires space for playing the game Be sure to leave enough space when installing the machine WARNING e Be sure to check the Electrical Specifications Ensure that this product is compatible with your location s power supply voltage and frequency requirement A plate describing Electrical Specifications is attached to the product Non compliance with the Electrical Specifications can cause a fire and electric shock e Putting many loads on one electrical outlet can cause generation of heat and a fire resulting from overload 4 3 Locations to avoid WARNING The machine is designed for indoor use only Never install this machine outdoors or in any of the following e Locations exposed to direct sunlight
19. enance Due to the design of the machine very little periodic maintenance Is required Start the game and verify the correct operation before putting the game into everyday operations Clean the surface of the game as needed After about a month of game operation check to be sure all parts are secure and in proper working order 1 Remove power before servicing game To avoid a short circuit the power must be removed before touching the inside of the game If you have to turn on the power please refer to section 2 2 2 Choose the appropriate replacement parts Using the wrong parts could lead to malfunction or damage to the game and components 3 Do not substitute or change equipment without authorization Doing so could lead to a short circuit and machine malfunction complete system failure and or fire 4 Do not put containers of water cups or soda cans on the machine In addition chemicals or heavy items should not be allowed around the game A spill of liquids or chemicals can seriously damage the sensitive electronic game components Falling items could injure people or destroy the machine 8 2 Cleaning CLEANING Clean the outer surfaces of the game with a commercial spray type cleaner DO NOT USE a glass cleaner or commercial chemical sprays on the marquee graphics panel DO USE a good quality spray type furniture polish to keep the game looking good Vacuum the inside of the game occasionally to help keep the dust and
20. f the new item s a Return Merchandise Authorization Number RMA will be issued for you to use when returning the defective item s to Bob s Space Racers Inc or you may use the order number After the defective item s is received by Bob s Space Racers Inc your account will be issued either a 1 Warranty credit if your game is under warranty See the Warranty Policy page Note this credit does not include return shipping charges 2 Credit for the item s Note this credit does not include return shipping charges nor does it include the repair charges for the item s If the item s cannot be repaired to the point where it could be shipped to another customer as an Advanced Replacement item i e cosmetic damage we will ship your original item s back to you You will be required to return the Advanced Replacement item s or pay for it You will be responsible for all shipping charges should you decide to not keep and pay for the Advanced Replacement item s ADVANCED REPLACEMENT ITEM S SHIPPING RULES When you request an Advanced Replacement item from us we have a few rules for you to follow 1 DO NOT try to repair the defective item s on your own DO NOT disassemble the defective item s prior to returning it to Bob s Space Racers Inc this could cause further damage and the possibility of you not receiving any credit at all on the item s There are not any user serviceable parts inside and our vendors may void t
21. h the shaft with Scotch bright Remove any rust spots with an emery cloth BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 Procedure 3 Instructions Removing Mole Heads for cleaning 1 Turn off the A C power to the game 2 Remove the 2 bolts that attach the playfield 3 Lift the playfield up and pull forward to remove it to the top of the main cabinet from the unit rs ae 4 Remove the 4 bolts and washers 7 16 that 5 Remove the coil bed assembly by carefully secure the coil bed to the cabinet lifting it up 6 Disconnect the two Molex connectors that are connected to the coil bed assembly BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 7 Remove the clip using needle nose pliers or 8 Remove Mole Head from the Assembly by pulling it a small screwdriver out and then remove the 3 washers from the shaft Make note of the order of the washers on the top and bottom of the shaft o Clean the shaft using a soft cloth and an electrical contact anti corrosion cleaner such as ElectriCorr VPCL 239 or equivalent Polish the shaft with Scotch bright Remove any rust spots with an emery cloth 10 Clean the bore in the assembly with a gun cleaning kit Gun cleaning kits can be purchased at a local Wal Mart store 11 Reassemble the washers on the top part of the shaft Note the correct order 20 BOB S SPACE RACERS Inc WHAC A MOLE
22. heir warranty on disassembled parts Please review the last paragraph of the Advanced Replacement Policy 2 Wait for the Advanced Replacement item s to arrive prior to returning the defective item s 3 When the new item s arrive verify that it is the correct part If it is not please note what the differences are and contact Bob s Space Racers Inc 4 Return the defective item s in the exact same packaging the Advanced Replacement item s came in This insures no more damage will be done to the item s during the return shipping Thank you for your cooperation 31 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 11 WARRANTY 5 SPACE RACERS INC 90 DAY COIN OPERATED GAME WARRANTY 1 INCLUDED IN THIS WARANTY Bob s Space Racers Inc warrants to the original purchaser only that the equipment that is the subject of this sale conforms to its specifications and is free from defects under normal service for a 90 day period from the original date of deliver This warranty does not include any damages resulting from occurrences listed in paragraph 2 below This warranty is not transferable under any circumstance Any claims under this warranty must be received in writing by Bob s Space Racers Inc within 120 days from date of delivery Within a reasonable time of such written notification Bob s Space Racers Inc will replace or repair any defective component of the equipment or part thereof which fails for
23. lectronic mech Check programming options and adjust Repair and or replace Front Panel Board Repair and or replace Main P C board Refill ticket dispenser and press the reset button Clear ticket jam Clean off sensor Check and or replace connectors Check ticket programming options Replace dispenser Check and or repair harnessing Repair and or replace Front Panel Board Replace or repair Main P C Board Check on off switch and power SOR andor replace sensor pair See Descr m 57 belo A Check andar replace fuse as necessary Replace or tighten faulty ground wire See moles won t pop up below Check and or replace the 12VDC power supply Repair and or replace Front Panel Board Repair and or replace Main P C Board Reconnect the connector securely Check all circuitry for bad connection or short circuits Remove han clus eoan EIS and solenoid Check that fhe AR is ESCORT tightened Check and or replace sensors Check and or replace the 36VDC power supply Check and or replace the 36VDC power supply Check coil resistance and replace solenoid coil Repair or replace main P C board Check connections Check and or Sensor Clean Sensor Descrip Check and or Race 4 See Tighten parts e NAIA V Qoa aerrintinn A h lt Je SCII A andlor eee mole shaft Replace the lamps Check connections and connectors Check and or repair harnessing Replace or
24. on or service e damage caused by normal wear and tear or improper power supply f damage caused by accident or disaster such as fires flood lightning and wind or g any other abuse or misuse of the equipment 3 EXCLUSIVE WARRANTY THE FORGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES OR REMEDIES WHETHER WRITTEN ORAL OR IMPLIED THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE COURSE OF DEALING OR USAGE OF TRADE ARE HEREBY EXPRESSLY DISCLAIMED AND EXCLUDED 4 REMEDIES LIMITED UNDER NO CIRCUMSTANCES EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW SHALL BOB S SPACE RACERS INC BE LIABLE FOR ANY LOSS OR DAMAGE DIRECT OR INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT INCLUDING BUT NOT LIMITED TO ANY CLAIM FOR LOSS OR PROFITS LOSS OF SAVINGS OR REVENUE LOSS OF USE OF THE EQUIPMENT OR ANY ASSOCIATED EQUIPMENT FACILITIES OR SERVICE DOWNTIME THE CLAIMS OR COSTS OF THIRD PARTIES INCLUDING CUSTOMERS AND INJURY TO PROPERTY Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state 5 NO OTHER
25. rator BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 6 INSTRUCTION FOR PLAY 1 Swipe the card or insert coins to play After at least two players coin up the game will start after the countdown sequence 2 The object of the game is to hit the moles heads with the hammer as soon as the mole sticks its head out of the hole 3 The first player to reach the high score will win 4 Progressive speed modes have been added to increase the level of skill that it takes to achieve a higher score BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 7 OPTION SETTINGS FEC Whac A Mole Game Options ume m T n ewm T EN P1 jCostperpay ju 1 P2 lEndinpscoe Mo30 15 03 _ 020 0 Beacon Light Time _ em 1 P5 Time Out 1 30 60 45 7 jAtracinteval 3 P8 junused fon 1 _______ od 1 PA Gameplaylor2Heads Lu 1i unused O 15060 50 1 PC jAttractShow Target Time _ 2050 30 PD jStartHeadUpTime gt 2090 60 PE____ Progressive Interval J 063 0 lGame Mode On Off o1 o PH____ Progressive SpeedUp 0 jResetDefualts 53 n 0 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 7 1 Setting Options Game Programming Game Programming Module T i P
26. reasons other than normal service use or wear Bob s Space Racers Inc reserves the right to request dated proof of purchase by the end user original purchaser at any time Light bulbs are specifically excluded from this warranty and shall be the sole responsibility of the purchaser Bob s Space Racers Inc within its sole discretion makes the final determination as to whether to repair or replace any component and whether any such repair or replacement shall be performed where the equipment is located or at it s home facility in Volusia County Florida or another facility of its sole choice Any and all freight charges for the purposes of repair or replacement shall be paid by the original purchaser All defective parts shall be returned to Bob s Space Racers Inc if requested Bob s Space Racers Inc does not warrant that the equipment will meet any original purchasers specific requirements or that the operation of the equipment will be uninterrupted These remedies are the original purchaser s exclusive remedies for breach of warranty 2 EXCLUDED BY THIS WARRANTY Bob s Space Racers Inc does not warrant a any product components or parts not manufactured by Bob s Space Racers Inc b damages caused by use of the equipment for purposes other than those for which it was designed c defects caused by failure to provide a suitable installation environment for the equipment d damage caused by unauthorized attachments modificati
27. repair main PC board BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 Description A Instructions on How to change and repair mole shaft This procedure can be used if the Mole heads are slow to come up Below is listed a possible solution to these two problems but are not all inclusive Remove the mole box as per Mole Head Removal procedure at the bottom of the shaft you will find a ring retaining clip being very careful remove this retaining ring BEFORE you remove the shaft make a note as to the order of the rubber and plastic washers so that you re assemble back in the same order Once the shaft has been removed take a clean SOFT cloth to wipe the shaft clean from any dirt or contamination that may have built up also clean the inside of the coil where the shaft fits into Using light lube oil i e WD 40 LIGHTLY oil the shaft using a clean soft cloth wiping any excess lube SCORING from the shaft and coil Re install the shaft using the same SENSORS procedure in a reverse process Description B Transmitter Sensor Receiving Sensor 25 BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 MECHANICAL REPAIR COIL BED SERVICING The coil bed is the assembly that houses the solenoids score sensors and mole heads This unit is built as an assembly to make servicing and repair easy The entire unit removes from the game as a sub assembly in just a couple of minutes
28. rogram Button Select Button Step Button The programming options are available to the game operator for the purpose of customizing the game options to suit their operation Game units are shipped being set to the default settings Please see the options sheet for a description of the game options Button Operation Description Program Button This button is used to access the IO Options mode in the game unit Press the Program Button once to enter the mode Once pressed the left most and center displays will change to display the IO Options menu Press the Program Button again and hold for two seconds to exit the IO Options mode The unit will reset and run the initial POST POST involves testing system configuration by popping the moles heads and will display the revision numbers across the displays before entering game play mode Select Button This button is used to cycle through the IO Options PO Pr By pressing the Select Button the left most display will change and display the game options PO Pr Use this button to access the options that are desired to be changed otep Button Tis button is used to change the settings within the different options Once in the Options mode the Step Button will change the setting level in the options that were selected with the Select Button BOB S SPACE RACERS Inc WHAC A MOLE FEC MANUAL BSR V1 0 8 MAINTENANCE AND INSPECTION 8 1 Maint
Download Pdf Manuals
Related Search