Headrest DVD Player - Sparks Toyota
Contents
1. Sro j Remove the two piece S I A B strap from the mounting stud and spread apart Fig 11 9 Issue B 12 21 09 Page 16 of 26 pages TOYOTA Sienna 2011 DVD RSE Section II Installation Procedure amp k Continue lifting the sides of the seat cover material up over and off of the seat foam completely turning the seat cover material inside out Fig 11 10 Ai fy AN AN Fa TAV THY Fig 11 10 1 Marking the Foam Seat Structure Fig 11 11 Felt Tip 1 Install the Seat Top Marking Template Marker An aligning with the headrest post guides 2 Mark the opening in the Seat Top Marking Template with a felt tip marker ZN amp NOTE Do NOT cut seat foam amp m Foam Removal and Foam Cutting Fig 11 12 Fig 11 11 1 Spread and lift the seat foam from the back up and off of the seat exposing the seat back framework 2 Using a razor knife carefully cut the seat foam in the area indicated by the Foam Marking template 3 Remove the excess foam Fig 11 12 Issue B 12 21 09 Page 17 of 26 pages TOYOTA Sienna 2011 DVD RSE Section II Installation Procedure 12 Seat Top Dock Bracket Mounting The following process is performed for both driver and passenger seats amp a Holding the nut plate in place mount the lower bracket to seat structure using two M5 x 12mm screws Fig 12 1 Y 1 Install the lower bracket screws and torque to 442. 3 Fig 9 2 amp c Secure the power audio interface harness 1 under the ventilation duct 2 to the ground harness with one zip tie 2 Fig 9 3 d Route the power audio interface harness 1 through the lower IP location Secure the harness to the ventilation duct with one piece of foam tape 2 Fig 9 3 e Secure the power audio interface harness 1 to the cigarette lighter harness with one zip tie 3 Fig 9 3 W NOTE Remove foam tape from AUX harness Cut all excess lengths of cable ties Issue B 12 21 09 Page 11 of 26 pages TOYOTA Sienna 2011 DVD RSE Section II Installation Procedure g Connecting the Power Harness and Installing the Fuse Holder 1 Locate the 12V accessory adaptor connector disconnected in Figure 6 2 Fig 9 4 2 Install one T Tap connector on the blue wire and one T Tap connector on the white with black stripe wire Fig 9 4 i Install the T Tap connectors Fig 9 5 1i Place wire in open channel 1 iil Fold connector body until element contacts wire 2 iv Crimp connector closed with pliers 3 3 Connect the male spade connector with the red wire on the Power Audio Interface Harness to the T Tap secured to the vehicle s blue wire Fig 9 4 4 Connect the male spade connector with the black wire on the Power Audio Interface Harness to the T Tap secured to the vehicle s white with black stripe wire Fig 9 4 24
3. do not pull on the wires pull on the connectors 1 Vehicle Preparation and Protection Socket 10 mm Ratchet Negative Battery a Set the emergency brake and unlock all vehicle doors fe b Open the hood and apply protective covers to the fender grill area by the battery amp c Remove the negative battery cable Fig 1 1 amp oo 1 Do not touch the positive terminal with any tool when removing cable NOTE For vehicles with power seats perform procedures described in Section II steps 6 a 1 through 4 and b 1 through 5 before removing the negative battery cable A CAUTION Do not disconnect the connectors under the seats unless the negative battery cable is removed d Cover the 2 row seats and the interior of vehicle using seat covers and blankets Issue B 12 21 09 Page 2 of 26 pages TOYOTA Sienna 2011 DVD RSE Section II Installation Procedure 2 Fixed Center Console Removal Fixed center amp NOTE If the vehicle has a sliding center console console proceed to Section II 3 Sliding Center Console Removal amp NOTE If the vehicle does not have a center console proceed to Section II 4 Vehicles without Center Console NOTE Place all parts of the center console and attaching hardware on a protective blanket outside the vehicle following removal a Remove the cup holder Fig 2 1 1 Open the center console storage door 1 2 Lift the cup holder up and ou
4. 5 Route the fuse holder 1 towards the passenger Lower IP Kick Panel and VAN p w secure with two zip tie 2 and one piece of foam tape 3 Fig 9 6 Issue B 12 21 09 Page 12 of 26 pages TOYOTA Sienna Section II Installation Procedure Socket 10mm Issue B 12 21 09 2011 DVD RSE 10 Installing the Audio Interface Module AIM amp a b c d e _ e and Bracket Re install the floor carpet to its original position Pull all of the under the seat wire connectors Driver and Passenger Side Extension Harness connectors and the Power Audio Interface Harness Connectors through the OE openings in the floor carpet Fig 10 1 Clean the floor pan of the vehicle with VDC approved cleaner Fig 10 1 Place one piece of butyl tape on each foot of the AIM Bracket Remove the protective backing on the butyl tape pieces Feed the AIM Bracket mounting feet through the carpet cuts in the mounting location and press the AIM Bracket down to the floor pan of the vehicle Fig 10 1 Place the AIM on the AIM Bracket with the four wire harnesses facing the driver side of the vehicle Secure the AIM to the AIM Bracket using the four nuts Fig 10 2 Y 1 Install the four nuts and torque to 121in lbf o o 1 4 N m Connect the 4 color coded connectors on the AIM to the four color coded extension harness connectors Fig 10 2 Install
5. the seat material c Route the passenger side seat top dock harness red and green color coded connectors from the seat top dock down to the bottom of the seat Fig 14 1 d Attach the seat top dock using four M4 x Smm screws 1 y 1 Install the seat top dock screws and torque to 15 in lbf 1 7 N m e Snap the plastic top cover on the seat top dock Fig 14 1 Issue B 12 21 09 Page 21 of 26 pages TOYOTA Sienna 2011 DVD RSE Section II Installation Procedure f Using one piece of foam tape 1 secure the harness to the seat framework Fig 14 2 g Insert the harness in a piece of split loom 2 to protect the harness from chafing against the grocery bag hook bracket Tape both ends of the the split loom with electrical tape h Attach the split loom assembly to seat framework using foam tape 3 1 Attach the harness to the seat back using one piece of foam tape 4 and a cable tie 5 j Re assemble the driver and passenger seat cover material the remaining 1 2 of the way down the seat 1 Attach the two purple elastic tension P NS cords to the seat using two hog rings ma TEA S SN L 2 Cut the two 8 inch cable ties from the lt a purple elastic tension cord and discard C JEN ae E aw 3 Reinstall the five hog rings 1 from the bottom of the seat cover under protective flap Fig 14 4 k Turn over the seats exposing the wire harnesses ro
6. DVD player Press the eject button on each of the DVD players Check all switches on the lower center I P Turn the vehicle radio OFF and turn the ignition key to the OFF position Vehicle Function Checks Air Conditioner Fan Radio Back Light Accessory Adaptor Connector Accessory Adaptor Illumination Emergency Flashers Check all switches on the lower center I P Diagnostic Codes using Handheld Scan Tool OD OJOOUVUOUOVUU Seat bolt confirmations Page 26 of 26 pages Issue B 12 21 09 DVD RSE Verify the backlighting illuminates displays the TOYOTA Logo and the power LED illuminates red Verify that the DVD accepts the discs Verify that DVD video is displayed on the LCD monitors Verify that audio from the Passenger Side DVD can be heard through the vehicle speakers Verify that audio from the DVD can be heard through the headphones Verify that Headrest DVD discs stop playing Verify that DVD players eiect the discs properly Verify that DVD players eject the discs properly Functioning Air Conditioner Functioning Fan Functioning Radio Back Light Functioning Accessory Adaptor Functioning Accessory Adaptor Illumination Functioning Emergency Flashers Verify that all switches function properly Confirm that no diagnostic trouble codes are present 1 Confirm torque range 24 30 ft lbf
7. Fig 4 1 b Remove three pushpins 2 Fig 4 1 c Remove the two 10mm bolts 3 from the lower IP floor cover Fig 4 1 ED Socket 10mm Ratchet 5 Lower Center Console Storage Tray Removal a Remove lower center console storage tray S and forward panel assembly 1 Using a plastic pry tool remove the push pin 1 and then remove the kick panel 2 on the driver and passenger sides Fig 5 1 2 Disengage the four retaining clips 1 two on the passenger side and two on the driver side using a plastic pry tool Fig 5 2 3 Disconnect the 12V accessory adaptor connector 3 and the AUX connector W 2 Fig 5 2 amp 4 Remove lower center console storage tray and store on protective blanket Page 5 of 26 pages TOYOTA Sienna 2011 DVD RSE Section II Installation Procedure 6 Front Driver and Passenger Seat Removal amp CAUTION Before beginning Step 2 wait for at least 90 seconds after disconnecting the negative cable to prevent the airbag from deploying NOTE The procedures described below are for the both the front driver and passenger seats unless otherwise specified amp CAUTION The procedure described below can affect the SRS airbag system Read the precautionary notices concerning the SRS W airbag system before proceeding See page RS 1 of the service manual a Remove Front Seat Anchor Bolts 1 Remove the headrests from the driver and passenger fron
8. TOYOTA Sienna Section I Installation Preparation 2011 DVD RSE Part Number PT900 08100 RSE AUX PT900 08110 RSE USB AUX Kit Contents Quantity Reqd Seat Top Dock Assembly Seat Top Dock Cover Extension Cable Audio Interface Module Bracket CE ee Harness So 2 _ LowerBracket 9 2 Upper NutPlate Hardware Bag Contents Cable Tie 8 Black 18 Foam Pads 2 5 x 1 5 6 2 Female T Tap Connector Hog Ring 8 8 Screw M5 0 5 x 12mm BHSCS 9 8 Screw M4x 28mmSHCS_ _ Additional Items Required For Installation 1 1 Universal Seat Top LCD DVD PT900 00101 Conflicts Po Recommended Tools Personal amp Vehicle Notes Protection Vehicle Protection Blankets Seat Covers Protective Seat Feet Covers Part Boxes Special Tools a Installation Tools Pliers o o Issue B 12 21 09 Page 1 of 26 pages NOTE Part number of this accessory may not be the same as the part number shown Drive Ratchet wy 1g Socket 10 mm 11 mm 12 mm 14 Torque Wrenches 10 50 Ibfein 5 75 Ibfeft Ratchet Extension Screwdriver Phillips 2 Masking Tape Razor Knife Side Cutters o o Test DVD Dises D J o Headphones Test Remote Control Allen Key VDC Approved Cleaner CC Special Chemicals None Color Applicability Trim Level Vehicle Trim Color General Applicability Recommended Sequence of Application Accessory Mandatory Legend STOP Damage to
9. aoe Pry Tool Side Cutter J TE s ez ay LY I 7 KO OSA Fig 11 6 IO N aE Issue B 12 21 09 2011 DVD RSE d Loosen the seat cover material under the headrest support post guides on each seat 1 Insert a plastic pry tool under the seat cover material and seat foam Fig 11 4 2 Carefully lift and loosen the cover material and seat foam while rotating the plastic pry tool around the headrest support post guides Fig 11 4 e Using a side cutter remove the five hog rings 1 from the bottom of the seat back cover under the protective flap Fig 11 5 f Pull the seat back cover outward to expose the hog rings Using a side cutter remove the three hog rings releasing the purple elastic tension cords Attach two amp inch cable ties to the purple elastic tension cords Fig 11 6 Page 15 of 26 pages TOYOTA Sienna 2011 DVD RSE Section II Installation Procedure From the front of the seat pull the seatback material from the bottom of the seat outward Fig 11 7 amp h Carefully ease both sides of the seat material upward turning it inside out to the middle of the seat back Fig 11 7 amp 1 Pull the seat foam outward away from the seat frame to expose the S I A B strap 10mm Socket Remove the acorn nut 1 from the airbag Ratchet clamp assembly Fig 11 8 NOTE Reinstall the S I A B strap assembly and torque to 49 in lbf 5 5 N m
10. in lbf 5 N m NEE Phillip Screwdriver b Holding the nut plate in place mount the ED Phillip Screwdriver M5 x 12mm screws Fig 12 2 upper bracket to seat structure using two Y 1 Install the upper bracket screws and torque to 44 in lbf 5 N m c Spread the seat foam and slide it back onto the framework and pull the seat material down to the middle of the seat d Reattach the S I A B strap assembly in reverse order as shown in step 11 1 and j see Fig 11 8 and 11 9 Y 1 Install the S I A B strap assembly and torque to 49 in lbf 5 5 N m e Making sure the seat material is pulled tight over the seat top use a plastic pry tool to refit the foam and seat material around the headrest support post guides Issue B 12 21 09 Page 18 of 26 pages TOYOTA Sienna 2011 Section II Installation Procedure e Allen Key Issue B 12 21 09 13 Page 19 of 26 pages DVD RSE Seat Top Dock Installation Passenger Side a Marking the Top of the Seat 1 Install the Seat Top Marking Template SNA11 030 03 aligning with the headrest post guides 2 Mark the four circles and the slot marked PASS with a felt tip marker 3 Remove the template b Cutting the Top of the Seat Material 1 Using a razor knife carefully cut the seat material in the PASS location 2 Using a razor knife mark carefully cut the four circles marked in the seat material c Route the
11. ion key to ACC position c Press the power button on each of the DVD players Verify the backlighting illuminates displaying the TOYOTA Slash Screen and the power LED illuminates bright red d Insert a DVD into each of the DVD players Verify that the DVD players accept the discs e Press the play button on the remote control Verify that the DVD video is displayed on each of the LCD monitors NOTE On the wireless headphones the Page 24 of 26 pages 1 2 switch allows the user to select the audio from either the Passenger Side CH 1 or the Driver Side CH 2 When sitting in front of the passenger side screen use the CH 1 switch setting When sitting in front of the driver side screen use the CH 2 switch setting f Using the test wireless headphones verify that audio from each of the DVD players can be heard through the headphones and with the correct channel settings g Press the power button on the head unit and verify that the radio turns on h Press the AUX button on the head unit and verify that the audio is heard from the DVD playing on the Passenger Side DVD 1 Disconnect negative battery terminal TOYOTA Sienna Section II Installation Procedure Issue B 12 21 09 2011 DVD RSE j Reassemble the vehicle interior components and trim k Install seat bolts and torque to 27 ft lbf 37 N m 16 Final Preparation V V V VW a Place the owner s manua
12. l in the glove box b Place the remote control in the center console c Place the headphones in the rear cargo area d Reconnect negative battery terminal and tighten nut to 36 Ibf in 4 1 N m e Temporarily install short pin f Perform the seat occupancy re calibration procedure g Re initialize windows and doors 17 Airbag Diagnostic Check Page 25 of 26 pages a Connect the scan tool connector to the vehicle s diagnostic connector b Turn the ignition switch to the ON position c Check for Airbag ECU Trouble codes if present then clear the DTC s Refer to handheld scan tool tester operator s manual for further details NOTE Check for the latest version of the software on Toyota Information System TIS before setting up the scan tool NOTE Ensure the software is the latest version NOTE Download the latest software from Toyota Information System TIS TOYOTA Section II Installation Procedure Sienna 2011 Accessory Function Checks Turn the ignition key to the ACC or Run position and turn the vehicle radio ON Press the power button on each of the DVD players Insert a DVD into each of the DVD players Press the play button on remote control Press the Power button and the AUX button on the radio Press and release the power button on the test wireless headphones to turn them on Press the STOP button on each of the
13. on Fig 6 2 Fig 6 3 9 Remove the front seats and store on protective blanket CAUTION Place protective blanket on door entry Be careful not to damage the vehicle door trim when removing the seats TOYOTA Sienna Section II Installation Procedure Plastic Pry Issue B 12 21 09 2011 DVD RSE 7 Front Kick Panel Cover amp Cowl Cover Removal and Floor Carpet Preparation NOTE Place all parts and attaching hardware on a protective blanket outside the vehicle following removal o sro KO o d Page 8 of 26 pages Remove the driver side front kick panel cover and cowl cover 1 Manually unscrew the screw 1 on the driver side cowl cover and remove with the kick panel cover 2 using a plastic pry tool Fig 7 1 Remove the passenger side front kick panel cover and cowl cover 1 Manually unscrew the screw 1 on the passenger side cowl cover and remove with the kick panel cover 2 using a plastic pry tool Fig 7 2 Disengage the vehicle harnesses 1 from the three clips 2 located under the front kick panel covers on both the driver and passenger sides Fig 7 3 Remove the three clips 2 using a plastic pry tool Fig 7 3 TOYOTA Sienna Section II Installation Procedure gt Felt Tip Marker Side Cutters Issue B 12 21 09 2011 e n g Page 9 of 26 pages DVD RSE Using the AIM Bracket Cutting Templa
14. one christmas tree tie into the hole in the top of the AIM Bracket Route the four wire harnesses with color coded connectors toward the christmas tree tie and secure in place Fig 10 2 y NOTE Do NOT force connectors Mating connectors are keyed for proper alignment 0 Page 13 of 26 pages Connect the 2 pin power connector and 14 pin audio connector to the AIM Fig 10 2 TOYOTA Sienna 2011 DVD RSE Section II Installation Procedure k Cut excess length of the christmas tree tie 11 Passenger Side and Driver Side Seat Preparation and Seat Top Dock Installation a Undo the protective seat bottom flap by releasing the two elastic straps 1 secured under the seat and fold back Fig 11 1 b Remove the grocery bag hook from the seat back Fig 11 2 1 Remove the grocery bag hook trim 1 using a plastic pry tool 2 Remove one screw 2 using a phillips screwdriver 3 Remove grocery bag hook assembly 3 Plastic Pry Tool Phillips Screwdriver c Remove the arm rest Fig 11 3 1 Remove the bolt cover 1 using a plastic pry tool ED Plastic Pry 2 Using a 10mm Socket and Ratchet Tool remove one bolt 2 one washer 3 and 10mm Socket Ratchet one wave washer 4 3 Remove the arm rest and store on protective blanket Issue B 12 21 09 Page 14 of 26 pages TOYOTA Sienna Section II Installation Procedure Seat Top Headrest Support Post Guides
15. passenger side seat top dock harness red and green color coded connectors from the seat top dock down to the bottom of the seat Fig 13 1 d Attach the seat top dock using four M4 x Smm screws 1 1 Install the seat top dock screws and torque to 15 in Ibf 1 7N m e Snap the plastic top cover on the seat top dock Fig 13 1 f Using one piece of foam tape 1 secure the harness to the seat framework Fig 13 2 g Insert the harness in a piece of split loom 2 to protect the harness from chafing against the grocery bag hook bracket Tape both ends of the the split loom with electrical tape TOYOTA Sienna 2011 DVD RSE Section II Installation Procedure h Attach the split loom assembly to seat framework using foam tape 3 1 Attach the harness to the seat back using one piece of foam tape 4 and a cable tie 5 Issue B 12 21 09 Page 20 of 26 pages TOYOTA Sienna 2011 DVD RSE Section II Installation Procedure ED 14 Seat Top Dock Installation Driver Side Allen Key M4 a Marking the Top of the Seat 1 Install the Seat Top Marking Template aligning with the headrest post guides 2 Mark the four circles and the slot marked DR with a felt tip marker 3 Remove the template b Cutting the Top of the Seat Material 1 Using a razor knife carefully cut the seat material in the DR location 2 Using a razor knife mark carefully cut the four circles marked in
16. t 2 Plastic Pry Tool b Remove the forward storage box garnish Fig 2 1 1 Disengage the six clips and remove the forward storage box garnish 3 amp c Remove the center console storage box A i i assembly 73 Je NE LZ ie W 1 Disconnect the 12V accessory adaptor connector 1 from the front of the storage box assembly Fig 2 2 2 Remove four anchor bolts 1 Fig 2 3 e Socket 10mm 3 Remove center console storage box Ratchet assembly and store on protective blanket i ju aT al n ara Sp 1 OAOE i a re i AEA Issue B 12 21 09 Page 3 of 26 pages TOYOTA Sienna 2011 DVD RSE Section II Installation Procedure 3 Sliding Center Console Removal Sliding Wes center SS Plastic Pry amp a Follow the procedures shown in Step 2 a b c console b Disengage the clips holding the rear trim panel 1 of the sliding center console Fig 3 1 c Remove the two 10mm bolts 1 from the rear portion of the sliding center console Fig 3 2 d Remove center console storage box assembly and store on protective blanket Socket 10mm Ratchet Issue B 12 21 09 Page 4 of 26 pages TOYOTA Sienna 2011 DVD RSE Section II Installation Procedure Plastic Pry Tool Issue B 12 21 09 4 Vehicles without Center Console a Disengage three clips from the lower IP floor cover 1 and remove
17. t seats Fig 6 1 2 Move the front seats to the most rearward position exposing the 14mm seat anchor bolts 1 Remove the two 14mm seat anchor bolts Ratchet 1 from the front legs Fig 6 2 1 3 Open the front bolt access covers 14mm Socket 4 Move the front seats to the most forward position 5 Open the rear bolt access covers exposing the 14mm seat anchor bolts 1 Remove the two 14mm seat anchor bolts 1 from the rear legs Fig 6 3 G NOTE Reinstall the front and back seat anchor ear Socket y bolts and torque to 27ft lbf 37 N m Ratchet NOTE Before tilting the seat backward use protective coverings on the seat mounting flange and trim 6 Tilt the seat backward exposing the bottom side Issue B 12 21 09 Page 6 of 26 pages TOYOTA Sienna Section II Installation Procedure A I AREEN AE T fm ioi od PLT Lrt d Ba ae a kl eE eS af F i JO J an AN L DA i a Issue B 12 21 09 2011 DVD RSE CAUTION To prevent damage to the SRS airbag system do not proceed with the following steps unless the negative battery cable is removed 7 Disconnect the connectors under each seat refer to service manual For Driver Side Fig 6 4 For Passenger Side Fig 6 5 amp 8 Use protective seat feet covers or Page 7 of 26 pages masking tape 4 to prevent scratching vehicle during the removal and reinstallati
18. te mark the carpet with a felt tip marker in the two required locations 1 on both sides of the driver side ventilation duct to be cut Fig 7 4 CAUTION Insert a hard surface barrier prior to cutting the carpet to protect the wire harness beneath the carpet Using side cutters cut through the floor carpet on the two marked lines Fig 7 4 CAUTION Be careful not to cut vehicle harness located under the carpet Fold the floor carpet backward toward the rear of the vehicle exposing the entire floor pan from under the dash to the B Pillar TOYOTA Sienna 2011 DVD RSE Section II Installation Procedure 8 Extension Harness Routing CAUTION Do not secure accessory harness to any harness with S R S Yellow harness routing a Passenger Side Extension Harness Routing amp 1 Align the red and green connectors 1 on one end of the extension harness with the connectors 2 of the existing vehicle harness under the passenger seat location Fig 8 1 2 Route the extension harness 3 under the ventilation duct 4 toward the front of the vehicle Secure the harness with one cable tie 5 at the point where the vehicle harness 2 crosses under the ventilation duct through the channel 6 Fig 8 1 amp NOTE The harness must be four inches from the channel 3 Route the extension harness 1 through the channel toward the driver side of the vehicle and under the driver side ventilation d
19. the vehicle may occur Do not proceed until process has been complied with OPERATOR SAFETY Use caution to avoid risk of injury CAUTION A process that must be carefully observed in order to reduce the risk of damage to the accessory vehicle and to ensure a quality installation TOOLS amp EQUIPMENT Used in Figures calls out the specific tools and equipment recommended for this process REVISION MARK This mark highlights a change in installation with respect to previous issue SAFETY TORQUE This mark indicates that torque is related to safety TOYOTA Sienna 2011 DVD RSE Preparation Care must be taken when installing this accessory to ensure damage does not occur to the vehicle The installation of this accessory should follow approved guidelines to ensure a quality installation These guidelines can be found in the Accessory Installation Practices document This document covers such items as e Vehicle Protection use of covers and blankets cleaning chemicals etc e Safety eye protection rechecking torque procedure etc e Vehicle Disassembly Reassembly panel removal part storage etc e Electrical Component Disassembly Reassembly battery disconnection connector removal etc Please see your Toyota dealer for a copy of this document NOTES Removed Parts amp Place all removed parts on a protected surface in an area they will not be damaged Connectors amp When disconnecting connectors
20. uct 2 Secure extension harness to the floor pan aan HE with three pieces of foam tape 3 Fig 8 2 pu y b Driver Side Extension Harness Routing amp 1 Align the blue and yellow connectors 1 on one end of the driver side extension harness to the connectors of the existing vehicle harness 2 under the passenger seat location Fig 8 3 2 Ne Route the extension harness 1 along the existing vehicle harness 2 looping the extension harness around towards the side of the vehicle and back toward the ventilation duct 3 so the the blue and yellow extension harness connectors 4 are aligned with the red and green extension harness connectors 5 Fig 8 4 stor 3 Secure the harness with four zip ties 4 Cut all excess lengths of cable ties Issue B 12 21 09 Page 10 of 26 pages TOYOTA Sienna 2011 DVD RSE Section II Installation Procedure 9 Installing the Power Audio Interface Harness amp a Measure 12 of the power audio interface harness from power audio connectors 1 Secure the power audio interface harness at the 12 mark to the existing vehicle harness located at the white wire harness bracket with one zip tie 2 Fig 9 1 b Route the power audio interface harness 1 under and along the ventilation duct 2 and toward the front passenger side of the vehicle Secure the power audio interface harness 1 in place with two pieces of foam tape
21. uted on the bottom side Issue B 12 21 09 Page 22 of 26 pages TOYOTA Sienna Section II Installation Procedure Fig 14 5 Cut Excess Cable Tie Issue B 12 21 09 2011 lt q lt lt q Page 23 of 26 pages DVD RSE 1 Continue routing the cables under and toward the front of the seat use four 8 cable ties 1 to attach the cables to the underside of each seat Fig 14 5 m Reattach protective seat bottom flap Fig 14 5 n Reinstall the passenger side and driver side seats to the vehicle 1 Return the passenger seat to the vehicle and connect the red and green seat cable to the red and green connectors on the headrest extension cable 2 Connect all other seat connectors 3 Reinstall the front and back seat anchor bolts and torque to 27 ft lbf 37 N m 4 Reinstall the passenger side arm rest and torque to 14 ft lbf 19 N m 5 Return the driver s seat to the vehicle and connect the blue and yellow seat cable to the blue and yellow connectors on the headrest extension cable 6 Connect all other seat connectors 7 Reinstall the front and back seat anchor bolts and torque to 27 ft lbf 37 N m 8 Reinstall the drivers side arm rest and torque to 14 ft lbf 19 N m TOYOTA Sienna Section II Installation Procedure Issue B 12 21 09 2011 DVD RSE 15 In Process Functional Test a Temporarily reconnect battery negative cable b Turn ignit
Download Pdf Manuals
Related Search