electronic service manual chapter 10
Contents
1. m escutcheon on the door page 8 14 Electronic Stand Alone Locks Service Manual 10 3 Servicing Exit Hardware Trim Escutcheon Parts SERVICING THE LIFT FINGER Each time you service the lift finger you need to replace the following parts with new parts Removing the lift 10 4 finger 1 escutcheon gasket C64564 lift finger screw page 4 9 Remove the following parts m escutcheon from the door page 8 13 m mounting standoffs page 10 2 m escutcheon gasket page 10 3 Note the orientation of the lift finger See Figure 10 3 Remove the lift finger screw and discard Remove the washer and lift finger Screw Lift finger Figure 10 3 Removing and reinstalling the lift finger Precision Hardware rim configuration shown Electronic Stand Alone Locks Service Manual Servicing Exit Hardware Trim Escutcheon Parts Reinstalling the lift 1 Position the lift finger on the escutcheon in the orientation noted in finger step 2 on page 10 4 2 Position the washer on the lift finger screw Tightly secure the lift finger with the lift finger screw 25 30 Ibs torque See Figure 10 3 3 Reinstall the following parts m escutcheon gasket page 10 3 m mounting standoffs page 10 2 m escutcheon on the door page 8 14 Electronic Stand Alone Locks Service Manual 10 5 Servicing Exit Hardware Trim Escutcheon Parts SERVICING THE MOUNTING PLATE Each time you service the mounting plate y2. SERVICING EXIT HARDWARE TRIM ESCUTCHEON PARTS This chapter contains instructions for servicing escutcheon parts for Electronic Stand Alone Exit Hardware Trim For instructions for servicing outside escutcheon parts for standard Electronic Stand Alone Locks see page 9 1 m To remove all of the parts from the Electronic Stand Alone escutcheon perform all of the steps for removing parts in each section of this chapter Begin with the mounting standoffs page 10 2 m To reinstall all of the parts in the Electronic Stand Alone escutcheon perform all of the steps for reinstalling parts in each section of this chapter Begin with the shear pin page 10 29 m To change the handing for the Electronic Stand Alone escutcheon see page 10 30 m To service an individual part see the section for that part The instructions refer to other sections as necessary If you need to service See Mounting standoffs page 10 2 Escutcheon gasket page 10 3 Lift finger page 10 4 Mounting plate page 10 6 Lever return springs page 10 8 Primary harness page 10 9 Control electronics board page 10 10 Electronic Stand Alone Locks Service Manual 10 1 Servicing Exit Hardware Trim Escutcheon Parts If you need to service See Reader assembly page 10 13 Motor assembly page 10 16 Locking plate page 10 20 Yoke page 10 22 Beam and beam roller page 10 24 Lever assembly page 10 26 Shear pin page 10 28 Note When servicing compon
3. 4 Reinstall the following parts m lift finger page 10 5 m escutcheon gasket page 10 3 m mounting standoffs page 10 2 m escutcheon on the door page 8 14 Electronic Stand Alone Locks Service Manual 10 7 Servicing Exit Hardware Trim Escutcheon Parts SERVICING THE LEVER RETURN SPRINGS Each time you service the lever return springs you need to replace the following parts with new parts Removing the lever return springs Reinstalling the lever return springs 10 8 iH H E escutcheon gasket C64564 cable tie lift finger screw page 4 9 mounting plate screws page 4 9 Remove the following parts m escutcheon from the door page 8 13 m mounting standoffs page 10 2 m escutcheon gasket page 10 3 m lift finger page 10 4 m mounting plate page 10 6 Remove the lever return springs from the yoke See Figure 10 5 SO SS SS SS SS SS SS SI Lever return springs Figure 10 5 Removing and reinstalling the lever return springs escutcheon 1 2 B A S 1 S shown Install the lever return springs onto the yoke posts See Figure 10 5 Reinstall the following parts m mounting plate page 10 7 lift finger page 10 5 escutcheon gasket page 10 3 mounting standoffs page 10 2 escutcheon on the door page 8 14 Electronic Stand Alone Locks Service Manual Servicing Exit Hardware Trim Escutcheon Parts SERVICING THE PRIMARY HARNESS A replacem
4. page 10 11 2 Perform steps 2 and 3 starting on page 9 24 Reinstalling the 1 Perform steps 1 and 2 on page 9 26 B A S LS smartcard 2 Reinstall the following parts reader assembly m electronics board page 10 11 primary harness page 10 9 mounting plate page 10 7 lift finger page 10 5 escutcheon gasket page 10 3 mounting standoffs page 10 2 escutcheon on the door page 8 14 Removing the 1 Remove the following parts B A S 1S dual m escutcheon from the door page 8 13 validation reader m mounting standoffs page 10 2 assembly m escutcheon gasket page 10 3 m lift finger page 10 4 m mounting plate page 10 6 m primary harness page 10 9 m electronics board page 10 11 2 Perform steps 2 and 3 starting on page 9 27 Reinstalling the 1 Perform steps 1 and 2 on page 9 29 B A S 1 S dual 2 Reinstall the following parts validation reader m electronics board page 10 11 assembly m primary harness page 10 9 m mounting plate page 10 7 lift finger page 10 5 escutcheon gasket page 10 3 mounting standoffs page 10 2 escutcheon on the door page 8 14 10 14 Electronic Stand Alone Locks Service Manual Servicing Exit Hardware Trim Escutcheon Parts Removing the B A S 1 S V proximity reader assembly Reinstalling the B A S 1 S V proximity reader assembly Removing the Keypad EZ reader assembly Reinstalling the Keypad EZ reader assembly Remove the foll
5. able for B A S I S control electronics boards See page 4 5 To replace a Keypad EZ control electronics board obtain a keypad control electronics board B80963 Each time you service the control electronics board you need to replace the following parts with new parts m escutcheon gasket C64564 m cable tie m lift finger screw page 4 9 m mounting plate screws page 4 9 Note To determine whether a B A S I S Lock has a B A S I S G or B A S LS V control electronics board look at the label on the center of the board B A S I S G is labeled as BAGLKS B A S I S V is labeled as BA_LKS Removing the 1 Remove the following parts B A S 1 S magnetic stripe control electronics board m escutcheon from the door page 8 13 m mounting standoffs page 10 2 m escutcheon gasket page 10 3 m lift finger page 10 4 m mounting plate page 10 6 m primary harness page 10 9 2 Perform steps 2 and 3 on page 9 8 Reinstalling the 1 Perform steps 1 through 5 on page 9 9 B A S I S magnetic 2 Reinstall the following parts stripe control primary harness page 10 9 electronics board E m mounting plate page 10 7 m lift finger page 10 5 m escutcheon gasket page 10 3 m mounting standoffs page 10 2 o escutcheon on the door page 8 14 10 10 Electronic Stand Alone Locks Service Manual Servicing Exit Hardware Trim Escutcheon Parts Removing the 1 Remove the following parts B A S 1 S smart c
6. able tie lift finger screw page 4 9 mounting plate screws page 4 9 tape for mounting the sounder for a B A S I S escutcheon only Removing the motor 1 Remove the following components assembly escutcheon from the door page 8 13 mounting standoffs page 10 2 escutcheon gasket page 10 3 lift finger page 10 4 mounting plate page 10 6 lever return springs page 10 8 2 Disconnect the motor connector from the primary harness See Figure 10 6 Motor connector eA Sounder O E X N B AY aA ATA Motor assembly FR Q Coy A SS S J2 X Socket head screw la we ee CON Dis KK Voor At S oy Figure 10 6 Removing the motor assembly B A S 1 S escutcheon shown 10 16 Electronic Stand Alone Locks Service Manual Servicing Exit Hardware Trim Escutcheon Parts 3 For B A S LS escutcheons pry the sounder off the escutcheon using a screwdriver 4 Using a 3 32 hex driver remove the socket head screw and spacer Remove the motor assembly from the escutcheon Reinstalling the 1 Rotate the gear on the motor assembly until the locking lever is as motor assembly close to the screw hole as possible as shown in Figure 10 7 Note If the locking lever does not move freely as you turn the gear gently move the locking lever into position a Socket head screw hole Locking lever S Figure 10 7 Rotating the motor assembly gear 2 Posi
7. am roller page 10 25 yoke page 10 23 lever return spring page 10 8 mounting plate page 10 7 lift finger page 10 5 escutcheon gasket page 10 3 mounting standoffs page 10 2 escutcheon page 8 14 Electronic Stand Alone Locks Service Manual 10 27 Servicing Exit Hardware Trim Escutcheon Parts SERVICING THE SHEAR PIN Replacements kits are available for shear pins See page 4 10 Each time you service the shear pin you need to replace the following parts with new parts escutcheon gasket C64564 cable tie lift finger screw page 4 9 mounting plate screws page 4 9 4 shoulder screws page 4 10 Removing the 1 Remove the following parts shear pin a escutcheon from the door page 8 13 mounting standoffs page 10 2 escutcheon gasket page 10 3 lift finger page 10 4 mounting plate page 10 6 lever return spring page 10 8 yoke page 10 22 beam and beam roller page 10 24 lever assembly page 10 26 2 Remove the shear pin from the lever See Figure 10 16 Sop Shear pin Figure 10 16 Removing and reinstalling the shear pin 10 28 Electronic Stand Alone Locks Service Manual Servicing Exit Hardware Trim Escutcheon Parts Reinstalling the 1 Insert the shear pin into the lever making sure that the shear pin is shear pin positioned in the lever so that the head faces the opposite direction of the lever handle See Figure 10 16 2 Reinstall the following parts lever assem
8. ard control electronics board m escutcheon from the door page 8 13 m mounting standoffs page 10 2 m escutcheon gasket page 10 3 m lift finger page 10 4 m mounting plate page 10 6 m primary harness page 10 9 2 Perform steps 2 through 4 starting on page 9 10 Reinstalling the 1 Perform steps 1 through 5 starting on page 9 12 B A S LS smartcard 2 Reinstall the following parts control electronics primary harness page 10 9 board im m mounting plate page 10 7 m lift finger page 10 5 m escutcheon gasket page 10 3 m mounting standoffs page 10 2 m escutcheon on the door page 8 14 Removing the 1 Remove the following parts B A S LS dual validation control electronics board m escutcheon from the door page 8 13 m mounting standoffs page 10 2 m escutcheon gasket page 10 3 m lift finger page 10 4 m mounting plate page 10 6 m primary harness page 10 9 2 Perform steps 2 and 3 on page 9 14 Reinstalling the 1 Perform steps 1 through 5 starting on page 9 15 B A S I S dual 2 Reinstall the following parts validation control primary harness page 10 9 electronics board E m mounting plate page 10 7 m lift finger page 10 5 m escutcheon gasket page 10 3 m mounting standoffs page 10 2 Oo escutcheon on the door page 8 14 Electronic Stand Alone Locks Service Manual 10 11 Servicing Exit Hardware Trim Escutcheon Parts Removing the B A S 1 S V pro
9. arts escutcheon gasket C64564 cable tie lift finger screw page 4 9 mounting plate screws page 4 9 4 shoulder screws page 4 10 Removing the yoke Remove the following parts m escutcheon from the door page 8 13 m mounting standoffs page 10 2 m escutcheon gasket page 10 3 m lift finger page 10 4 m mounting plate page 10 6 m lever return springs page 10 8 2 Unscrew the 4 shoulder screws and discard See Figure 10 12 3 Remove the yoke from the escutcheon Shoulder screws Shoulder screws Figure 10 12 Removing and reinstalling the yoke B A S I S escutcheon shown 10 22 Electronic Stand Alone Locks Service Manual Servicing Exit Hardware Trim Escutcheon Parts Reinstalling the yoke 2 Apply Lubriplate GR 132 grease or an equivalent quality petroleum around the slots on the face of the yoke Position the yoke in the escutcheon with the threaded nut down 3 Tightly secure the yoke to the escutcheon using the 4 new shoulder screws 20 25 Ibs torque See Figure 10 12 4 Reinstall the following parts lever return springs page 10 8 mounting plate page 10 7 lift finger page 10 5 escutcheon gasket page 10 3 mounting standoffs page 10 2 escutcheon on the door page 8 14 Electronic Stand Alone Locks Service Manual 10 23 Servicing Exit Hardware Trim Escutcheon Parts SERVICING THE BEAM AND BEAM ROLLER Each time you service the
10. beam or beam roller you need to replace the following parts with new parts m escutcheon gasket C64564 m cable tie m lift finger screw page 4 9 m mounting plate screws page 4 9 m 4 shoulder screws page 4 10 Removing the beam 1 Remove the following parts and beam roller m escutcheon from the door page 8 13 m mounting standoffs page 10 2 m escutcheon gasket page 10 3 m lift finger page 10 4 m mounting plate page 10 6 m lever return springs page 10 8 m yoke page 10 22 2 Remove the c clip from the lever spindle See Figure 10 13 Lever spindle Figure 10 13 Removing and reinstalling the c clip B A S I S escutcheon shown 10 24 Electronic Stand Alone Locks Service Manual Servicing Exit Hardware Trim Escutcheon Parts 3 Remove the beam and beam roller from the lever spindle See Figure 10 14 Slot in beam Dp Locking plate Lever spindle Beam Beam roller Figure 10 14 Removing and reinstalling the beam and beam B A S S escutcheon shown j Reinstalling the Place the beam on the lever spindle so that the slot in the beam beam and aligns with the locking plate See Figure 10 14 beam roller 2 Reinstall the c clip onto the lever spindle The orientation of the clip does not matter See Figure 10 13 3 Place the beam roller on the beam 4 Reinstall the following parts yoke page 10 23 lever return springs page 10 8 mounting plate page 10 7
11. bly page 10 27 beam and beam roller page 10 25 yoke page 10 23 lever return spring page 10 8 mounting plate page 10 7 lift finger page 10 5 escutcheon gasket page 10 3 mounting standoffs page 10 2 escutcheon in the door page 8 14 Electronic Stand Alone Locks Service Manual 10 29 Servicing Exit Hardware Trim Escutcheon Parts CHANGING THE HANDING Each time you change the handing you need to replace the following parts with new parts m escutcheon gasket C64564 m cable tie m lift finger screw page 4 9 m mounting plate screws page 4 9 m 4 shoulder screws page 4 10 Note When changing the handing for Precision Hardware mortise applications you must replace the lift finger with the correct lift finger for the desired handing To order the left hand lift finger use part number C64576 To order the right hand lift finger use part number C64568 1 Remove the following parts escutcheon from the door page 8 13 mounting standoffs page 10 2 escutcheon gasket page 10 3 lift finger page 10 4 mounting plate page 10 6 lever return springs page 10 8 yoke page 10 22 beam and beam roller page 10 24 lever assembly page 10 26 10 30 Electronic Stand Alone Locks Service Manual Servicing Exit Hardware Trim Escutcheon Parts 2 Make sure that the shear pin is positioned in the lever so that the head faces the opposite direction of the lever handle Then insert the lever through
12. ent kit is available for the B A S LS primary harness See page 4 10 To replace a Keypad EZ primary harness obtain a primary harness C1444 Each time you service the primary harness you need to replace the following parts with new parts escutcheon gasket C64564 cable tie lift finger screw page 4 9 mounting plate screws page 4 9 tape for mounting the sounder on the control electronics board make sure that you are properly grounded using an electrostatic discharge ESD protection Rit Touching the control electronics board without proper grounding can damage sensitive electronic components even if you don t notice any static discharge Before you handle the control electronics board or any component Caution Removing the 1 Remove the following parts primary harness m escutcheon from the door page 8 13 m mounting standoffs page 10 2 m escutcheon gasket page 10 3 m lift finger page 10 4 m mounting plate page 10 6 2 Perform steps 2 through 4 starting on page 9 5 Reinstalling the 1 Perform steps 1 through 3 starting on page 9 6 primary harness 2 Reinstall the following parts m mounting plate page 10 7 lift finger page 10 5 escutcheon gasket page 10 3 mounting standoffs page 10 2 escutcheon on the door page 8 14 Electronic Stand Alone Locks Service Manual 10 9 Servicing Exit Hardware Trim Escutcheon Parts SERVICING THE CONTROL ELECTRONICS BOARDS Replacement kits are avail
13. ents always test that the lock works properly when yourre finished SERVICING THE MOUNTING STANDOFFS Removing the 1 Remove the escutcheon from the door See page 8 13 mounting standoffs 2 Unscrew the 6 mounting plate standoffs from the mounting plate Mounting standoffs Mounting plate Figure 10 1 Removing and reinstalling the mounting standoffs Reinstalling the 1 Screw the 6 mounting standoffs onto the mounting plate mounting standoffs 2 Reinstall the escutcheon on the door See page 8 14 10 2 Electronic Stand Alone Locks Service Manual Servicing Exit Hardware Trim Escutcheon Parts SERVICING THE ESCUTCHEON GASKET Each time you service the escutcheon gasket you need to replace it with a new gasket Use part number C64564 when ordering Removing the escutcheon gasket Reinstalling the escutcheon gasket 1 Remove the followings parts m escutcheon from the door page 8 13 m mounting standoffs page 10 2 Peel the gasket off the escutcheon and discard See Figure 10 2 Note You may need to scrape remnants of the gasket from the escutcheon Figure 10 2 Removing and reinstalling the escutcheon gasket 1 Starting at the bottom of the gasket peel away the protective backing a small amount at a time while unrolling the gasket into position on the escutcheon Press the gasket into place on the escutcheon See Figure 10 2 Reinstall the following parts m mounting standoffs page 10 2
14. lift finger page 10 5 escutcheon gasket page 10 3 mounting standoffs page 10 2 escutcheon on the door page 8 14 Electronic Stand Alone Locks Service Manual 10 25 Servicing Exit Hardware Trim Escutcheon Parts SERVICING THE LEVER ASSEMBLY Each time you service the lever assembly you need to replace the following parts with new parts m escutcheon gasket C64564 m cable tie m lift finger screw page 4 9 m mounting plate screws page 4 9 m 4 shoulder screws page 4 10 Removing the 1 Remove the following parts lever assembly escutcheon from the door page 8 13 mounting standoffs page 10 2 escutcheon gasket page 10 3 lift finger page 10 4 mounting plate page 10 6 lever return spring page 10 8 yoke page 10 22 Oo m H Oo i E Oo m beam and beam roller page 10 24 10 26 Electronic Stand Alone Locks Service Manual Servicing Exit Hardware Trim Escutcheon Parts 2 Remove the lever from the front of the escutcheon See Figure 10 15 Lever Figure 10 15 Removing and reinstalling the lever assembly B A S LS escutcheon shown Reinstalling the 1 Make sure that the shear pin is positioned on the lever so that the lever assembly head faces the opposite direction of the lever handle See Figure 10 16 2 Insert the lever through the escutcheon positioning the lever so its handle will point toward the door hinges See Figure 10 15 3 Reinstall the following parts beam and be
15. ollowing parts with new parts m escutcheon gasket C64564 m cable tie m lift finger screw page 4 9 m mounting plate screws page 4 9 j Removing the Remove the following parts locking plate m escutcheon from the door page 8 13 m mounting standoffs page 10 2 escutcheon gasket page 10 3 m lift finger page 10 4 m mounting plate page 10 6 m lever return springs page 10 8 m motor assembly page 10 16 2 Slide the locking plate out of the escutcheon See Figure 10 10 Locking lever Locking plate Figure 10 10 Removing and reinstalling the locking plate B A S I S escutcheon shown 10 20 Electronic Stand Alone Locks Service Manual Servicing Exit Hardware Trim Escutcheon Parts Reinstalling the 1 Slide the locking plate into position as shown in Figure 10 11 Make locking plate sure that the locking lever of the motor assembly is inserted through the locking plate Locking plate Locking lever Figure 10 11 Reinstalling the locking plate 2 Reinstall the following parts motor assembly page 10 17 lever return springs page 10 8 mounting plate page 10 7 lift finger page 10 5 escutcheon gasket page 10 3 mounting standoffs page 10 2 escutcheon on the door page 8 14 Electronic Stand Alone Locks Service Manual 10 21 Servicing Exit Hardware Trim Escutcheon Parts SERVICING THE YOKE Each time you service the yoke you need to replace the following parts with new p
16. ou need to replace the following parts with new parts m escutcheon gasket C64564 m cable tie m lift finger screw page 4 9 m mounting plate screws page 4 9 j Removing the Remove the following parts mounting plate m escutcheon from the door page 8 13 m mounting standoffs page 10 2 m escutcheon gasket page 10 3 m lift finger page 10 4 2 Cut the cable tie off the mounting plate post and discard the cable tie See Figure 10 4 Mounting plate screws i 4 LG Td os l Cable tie DES Mounting plate 0 pe Mounting plate screws Figure 10 4 Removing and reinstalling the mounting plate 3 Remove the 5 mounting plate screws and discard 4 Carefully remove the mounting plate from the escutcheon 10 6 Electronic Stand Alone Locks Service Manual Servicing Exit Hardware Trim Escutcheon Parts Be careful not to drop the lever return springs on the control A electronics board They can easily damage the electronics Caution Reinstalling the 1 With the posts on the mounting plate inserted in the lever return mounting plate springs slide the mounting plate into the escutcheon See Figure Figure 10 5 Make sure that the locking plate fits into the slot in the mounting plate See Figure 10 4 2 Install the 5 new mounting plate screws 3 Route the primary harness against the mounting plate post and secure the harness to the post with a cable tie See Figure 10 4
17. owing parts escutcheon from the door page 8 13 mounting standoffs page 10 2 escutcheon gasket page 10 3 lift finger page 10 4 mounting plate page 10 6 primary harness page 10 9 electronics board page 10 12 Perform steps 2 and 3 on page 9 30 1 Perform steps 1 and 2 on page 9 31 2 Reinstall the following parts electronics board page 10 12 primary harness page 10 9 mounting plate page 10 7 lift finger page 10 5 escutcheon gasket page 10 3 mounting standoffs page 10 2 escutcheon on the door page 8 14 Remove the following parts escutcheon from the door page 8 13 mounting standoffs page 10 2 escutcheon gasket page 10 3 lift finger page 10 4 mounting plate page 10 6 primary harness page 10 9 electronics board page 10 12 Perform steps 2 and 3 on page 9 32 1 Perform steps 1 and 2 on page 9 34 Reinstall the following parts electronics board page 10 12 primary harness page 10 9 mounting plate page 10 7 lift finger page 10 5 escutcheon gasket page 10 3 mounting standoffs page 10 2 escutcheon on the door page 8 14 Electronic Stand Alone Locks Service Manual 10 15 Servicing Exit Hardware Trim Escutcheon Parts SERVICING THE MOTOR ASSEMBLY A replacement kit is available for the motor assembly See page 4 10 Each time you service the motor assembly you need to replace the following parts with new parts m escutcheon gasket C64564 c
18. re Trim Escutcheon Parts SERVICING THE READER ASSEMBLIES Replacement kits are available for the reader assemblies See page 4 4 Each time you service the reader assembly you need to replace the following parts with new parts escutcheon gasket C64564 cable tie E E E E Removing the 1 B A S I S magnetic stripe reader assembly 2 Reinstalling the B A S I S magnetic 2 stripe reader assembly lift finger screw page 4 9 mounting plate screws page 4 9 Remove the following parts escutcheon from the door page 8 13 mounting standoffs page 10 2 escutcheon gasket page 10 3 lift finger page 10 4 mounting plate page 10 6 primary harness page 10 9 electronics board page 10 10 Perform steps 2 and 3 starting on page 9 21 1 Perform steps 1 and 2 on page 9 23 Reinstall the following parts electronics board page 10 10 primary harness page 10 9 mounting plate page 10 7 lift finger page 10 5 escutcheon gasket page 10 3 mounting standoffs page 10 2 escutcheon on the door page 8 14 Electronic Stand Alone Locks Service Manual 10 13 Servicing Exit Hardware Trim Escutcheon Parts Removing the 1 Remove the following parts B A S I S smart card reader assembly escutcheon from the door page 8 13 mounting standoffs page 10 2 escutcheon gasket page 10 3 lift finger page 10 4 mounting plate page 10 6 primary harness page 10 9 electronics board
19. the escutcheon positioning the lever so its handle will point toward the door hinges See Figure 10 17 Shear pin head RAT Lever pmm ZN J Figure 10 17 Changing the handing 3 Reinstall the following parts beam and beam roller page 10 25 yoke page 10 23 lever return springs page 10 8 mounting plate page 10 7 lift finger page 10 5 escutcheon gasket page 10 3 mounting standoffs page 10 2 escutcheon on the door page 8 14 Electronic Stand Alone Locks Service Manual 10 31
20. tion the motor assembly in the escutcheon as shown in Figure 10 8 Make sure that m the locking lever is inserted through the locking plate m the motor assembly pivot pin is seated in the recess in the escutcheon Electronic Stand Alone Locks Service Manual 10 17 Servicing Exit Hardware Trim Escutcheon Parts Motor harness Motor assembly Pivot pin Locking lever Socket head screw Locking plate Figure 10 8 Routing the motor harness 3 Place the spacer on the socket head screw Using a 3 32 hex driver reinstall the socket head screw 4 Route the motor harness into the groove in the escutcheon as shown in Figure 10 8 5 For B A S LS escutcheons reinstall the sounder onto the escutcheon See Figure 10 9 10 18 Electronic Stand Alone Locks Service Manual Servicing Exit Hardware Trim Escutcheon Parts 6 Connect the motor harness to the primary harness Motor connector Sounder Figure 10 9 Reinstalling the motor assembly B A S I S escutcheon shown 7 Reinstall the following components lever return springs page 10 8 mounting plate page 10 7 lift finger page 10 5 escutcheon gasket page 10 3 mounting standoffs page 10 2 escutcheon on the door page 8 14 Electronic Stand Alone Locks Service Manual 10 19 Servicing Exit Hardware Trim Escutcheon Parts SERVICING THE LOCKING PLATE Each time you service the locking plate you need to replace the f
21. ximity control electronics board Reinstalling the B A S 1 S V proximity control electronics board Removing the Keypad EZ control electronics board Reinstalling the Keypad EZ control electronics board 10 12 Remove the following parts m escutcheon from the door page 8 13 m mounting standoffs page 10 2 m escutcheon gasket page 10 3 m lift finger page 10 4 m mounting plate page 10 6 m primary harness page 10 9 Perform steps 2 and 3 starting on page 9 106 1 Perform steps 1 through 3 on page 9 17 2 Reinstall the following parts m primary harness page 10 9 m mounting plate page 10 7 m lift finger page 10 5 m escutcheon gasket page 10 3 m mounting standoffs page 10 2 m escutcheon on the door page 8 14 Remove the following parts m escutcheon from the door page 8 13 m mounting standoffs page 10 2 m escutcheon gasket page 10 3 m lift finger page 10 4 m mounting plate page 10 6 m primary harness page 10 9 Perform steps 2 through 4 starting on page 9 18 1 Perform steps 1 through 3 on page 9 20 Reinstall the following parts m primary harness page 10 9 m mounting plate page 10 7 m lift finger page 10 5 m escutcheon gasket page 10 3 m mounting standoffs page 10 2 m escutcheon on the door page 8 14 To replace a Keypad EZ reader obtain a Keypad reader B603235 Electronic Stand Alone Locks Service Manual Servicing Exit Hardwa
Download Pdf Manuals
Related Search