HD788080 HD788081 - Senseo onderdelen
Contents
1. 13120 13130 13140 HD7880 80 HD7880 81 EXPLODED VIEW 12 122. connections and hoses and reinstall in the reverse order Any Ty wrap that has been removed needs to be replaced by a new one and tightened with the specified forces 3 To replace the PCBA 3 1 Unscrew the inner frame Unscrew the two screws 15 holding the inner frame in place take special care to note the proper wire routing and make sure reinstalling the PCBA will be done in an identical way 4 12 REPAIR INSTRUCTION HD7880 80 HD7880 81 Descaling Scale builds up inside the machine during use It is essential to descale the SENSEO coffee machine when the Light goes on If the descaling procedure is not performed correctly scale residue remains behind in the machine This causes scale to build up more quickly and may cause permanent and irreparable damage to the machine Use the correct descaling agent HD701 I HD7012 only It has been developed to ensure better machine performance and operation Never use a descaling agent based on mineral acids such as Sulphuric acid Acetic acid vinegar or Hydrochloric acid These descaling agents may damage your SENSEO coffee machine For detailed instructions please refer to the Directions For Use chapter User Programmable Volumes HD7884 only For any Senseo Up appliance in the HD7884 range the cup volume can be programmed by the consumer self to suit his personal coffee preference This can be done by pressing the button corresponding to the recipe to be
3. house bottom Back cover assy Back cover WC seal WC filter WC socket Housing Brewchamber cover Brewchamber assy Lid hinge cover Lid spring Hose Lever Lever frame Rod Slider left Slider right Slider spring Lid frame Ejector pin BC seal Distribution disk Brewchamber bottom Black Black Monza red Deep black Monza red Transparent Transparent Deep black Deep black Monza red Monza red Monza red Deep black Deep black Black HD7880 81 7 12 PARTS LIST HD7880 80 HD7880 81 Pos Service code Description Remark 15 4222 247 59473 Housing water level sensor I7 4222 247 08101 L bend 19 4222 259 61291 Tube P B incl restrictor 21 4222247 69442 Suspension bracket 23 4222 259 37244 Pump 230V 50 Hz 25 Tube B V 27 Boiler assy Metal 230V 2720 4222 247 05134 O ring NTC 2740 4222 259 60501 2760 4222 248 56001 TCO 29 Cordset 3l 4222 247 06301 Pump damper 8 12 HD7880 80 HD7880 81 EXPLODED VIEW HD7880 80 HD7880 81 EXPLODED VIEW T T ae Es Ba zu Z 4 A 10 12 11 12 HD7880 80 HD7880 81 1390 3 1 EXPLODED VIEW E I s x VN 722 N 22 Cen X 13100 7 13110
4. specification the deviation van be adjusted in steps of 3 5 mL The calculated deviation divided by 3 5 will tell you how many steps you need to in or decrease Follow the steps as mentioned under Service modes Manual pump calibration to recalibrate the pump 8 Measure the newly calibrated volume and repeat steps 5 7 if necessary 5 12 SERVICE MODES HD7880 80 HD7880 81 Manual pump calibration Keep the regular and strong cup button pressed while connecting the mains voltage to the appliance 2 The buttons can be released when the regular and strong cup LEDs are switched on a Press and release the strong cup button to decrease the calibration value The strong and regular cup LEDs blink for 0 5 second b Press and release the regular cup button to increase the calibration value The strong and regular cup LEDs blink for 0 5 second Press and release the strong and regular cup buttons to store the calibration value The strong and regular cup LEDs blink for second Service step 2a and 2b can repeatedly be used to adjust the calibration value Use service step 2c to store the new calibration value Mid end High end selection This steps follows automatically after step 2c storing the newly calibrated value To skip the calibration simply press the regular and stong button again after you connected the mains 3 Ifthe strong cup LED is on the appliance is ME version If the regular cup LED is on the ap
5. Service Servos Service Philips Consumer Lifestyle PRODUCT INFORMATION This product meets the requirements regarding interference suppression on radio and TV After the product has been repaired it should function properly and has to meet the safety requirements as officially laid down at this moment TECHNICAL INFORMATION Voltage 220 240V Frequency 50 Hz Power consumption 1400 Stand by power consumption lt 0 5 W Color setting Monza Red e Contents of water container 0 7 L 5 cups Dimensions Appliance 225 x 105 x 350 mm F Box 290x 165 x 390 mm Spout height 150 mm Cord length 80 cm Weight Appliance 2 05 kg F Box 2 17 kg Published by Philips Consumer Lifestyle Printed in the Netherlands 14 04 Materials Senseo Up HD7880 80 HD7880 81 Housing Driptray Back plate Water container amp Lid Collector Brewchamber bottom Lid cover Baseplate Driptray cover Buttons Lever Consumer Replaceable Parts 9044 0 9045 0 9047 0 9048 0 9053 0 9056 0 CP9057 0 Podholder Podholder 2 PP Tritan 5 PC Collector assy Monza red Drip tray cover Deep black Drip tray Monza red Water container lid Water container assy OPTIONAL accessories specific iss
6. e removed by unscrewing the two screws B T 5 and undoing the hose connection g from the one way valve To continue first remove the two screws A T I5 from the bottom side of the appliance 2 To reach internal components like Boiler or Pump 2 1 Remove the back plate and undo the hose connection g from the one way valve if not done so already To remove the back plate use a plastic tool and trace the parting line of the back plate undoing all the snaps The corrugated tube is still connected to the water container socket and can easily be pulled off 3 12 DISASSEMBLY AND RE ASSEMBLY ADVISE HD7880 80 HD7880 81 2 2 Remove the housing To remove the housing start at the back side and undo the clicks on either side of the back plate next continue on either the left of right side and undo the click on the long lower side of the housing next undo the snap on the front round edge of the housing Make sure that none of the snaps snap back Repeat this procedure on the other side of the appliance working from back to front Tip leave a screwdrive or plastic tool in the area where the first front click was released to prevent it snapping back Remove the housing upwards from the rest of the appliance but mind flat cable running through the guide on the inside of the housing and the water level sensor still connected to the inside of the housing You can now access the Boiler and Pump to remove them undo the electrical
7. pliance is a HE version a Press and release the strong cup LED to make the appliance a ME version b Press and release the regular cup LED to make the appliance a HE version C Press and release the strong and regular cup buttons to store the HE ME selection value The strong and regular cup LEDs blink for second Boiler reset Keep the strong cup button pressed while connecting the mains voltage to the PCBA 2 Button can be released when the strong cup LED or regular cup LED blinks rapidly The strong cup LED will burst in case of a ME version The regular cup LED will burst in case of a HE version 6 12 PARTS LIST 10 720 730 740 750 910 920 930 940 950 960 10 1010 1020 1030 1040 12 13 1310 1320 1330 1340 1350 1360 1370 1380 1390 13100 13110 13120 13130 13140 4222 259 60221 4222 259 60231 4222 259 60591 4222 247 72811 4222 247 72801 4222 247 72772 4222 259 60081 4222 259 60071 4222 247 72752 4222 259 60262 4222 247 7273 4222 247 72721 4222 259 58081 4222 247 72711 4222 259 60021 4222 247 7258 4222 247 72691 4222 259 6005 4222 240 0599 4222 247 08121 4222 247 72611 HD7880 80 Padholder Padholder 2 Collector assy Driptray cover Driptray Water container lid Water container assy Valve seal Valve spring Valve rod Float spring Float assy One way valve Top cover assy Top cover Buttons rubber Buttons plastic UI house top UI PCBA Ul
8. programmed until the LED starts flashing quickly Once the appliance is heated up it starts making the coffee press the button again once the desired volume is reached The LED will blink rapidly as confirmation the volume has been stored To reset the user programmable volumes to default 60 mL Strong coffee 125 mL Regular coffee keep both buttons pressed until the LED starts to flash Volume adjustment Note Volume adjustment may only be carried out in case the repair technician is sure there is no underlying cause e g User programmable volume leakage incorrect voltage setting etc for the deviation in volume from the factory default For the correct procedure on Volume measurement please refer to the Senseo Repair process How to adjust the volume output Make sure the boiler is filled properly otherwise perform the Flush before first use procedure according to the instructions in the DFU Reset the User Programmable Volumes by pressing both buttons until the LED starts to flash Make sure the collector and a pod holder without a coffee pod is installed in the appliance Calibrate the scale you are going to use for the measurement by placing the empty cup and switching it on 4 Press the Regular coffee button to start a regular coffee brewing process When finished also pour the leftover water in the pod holder into the cup Measure the output and compare to the specifications on P X Determine the deviation from the
9. ues Copyright reserved Subject to modification PHILIPS TECHNICAL INFORMATION HD7880 80 HD7880 81 General coffee specifications In cup volume mL Regular coffee Strong coffee General WEU version 125 60 France specific version 100 60 Temperature indication Regular coffee Strong coffee General WEU version gt 74 gt 72 France specific version Measurement specification Water spec without pod mL Regular coffee cup with I cup pod holder 133 10 Electical diagram User interface layout e Water level sensor Functional diagram 1 way valve 2 12 DISASSEMBLY AND RE ASSEMBLY ADVISE HD7880 80 HD7880 81 Make sure the appliances cordset is disconnected from the mains To open the appliance removal all detachable parts Water container driptray and cover pod holder and collector reach the brew chamber 1 1 Open the top cover To open to the top cover the brew chamber needs to be unlocked Start at the back side of the top cover using a plastic tool and trace along the parting line of the top cover undoing all the snaps There two small snaps on the front lower side of the brew chamber undo them with a small flathead screwdriver No 0 The top cover needs to be tilted forward to be removed The flat cable W from the PCBA to the UI PCBA is still attached to the User Interface panel and can easily be unplugged The brew chamber can now b
Download Pdf Manuals
Related Search