GS 1085 Cash Card Loader - GoPrint Systems
Contents
1. cheat lever one time to scroll to the next configuration option Continue depressing and releasing the anti cheat ever until the desired option is reached s Once the desired option is displayed depress and hold the anti cheat lever until the unit exits the configuration mode approximately 3 seconds The new configuration setting will flash 3 times to confirm the setting Replace the lower housing Test unit to insure proper set up REMOVING ACCEPTED BILLS Accepted bills may be removed by releasing the bill box lid exposing the bills or by removing the bill box from the bill acceptor Sce Figure 2 LOWER HOUSING Example 1 is 1 enable and high security disable HU 10 20 Security 1 5 Example 2 is 1 enable and high security enable Po oot 10 20 Security Figure Copyright 2007 GoPrint Systems Inc All Rights Reserved CLEARING JAMS amp CLEANING See Figure 2 Dirt or debris can result in poor bill acceptance or bill rejection Remove the bill box and lower housing to access the bill path for dirt or debris Clean the bill path plastic parts and belts with a cloth moistened with a mild soap and warm water solution Clean the magnetic head using isopropyl alcohol Do not use any petroleum based cleaning solvents scouring pads or stiff brushes for cleaning The BillPro bill acceptor requires no lubrication at any time Pull bill box lid open to remove To remove bil2. 00 Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Set Accept 10 00 Press the A or B to select Yes or No Followed by Enter to control the acceptance of 10 00 Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Set Accept 20 00 Press the A or B to select Yes or No Followed by Enter to control the acceptance of 20 00 Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Set Accept 50 00 Press the A or B to select Yes or No Followed by Enter to control the acceptance of 50 00 Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Command Mode Set Coins NOTE This feature is not activated for GoPrint Command Mode Card Reader Setup Command Menu Mode is initiated by pressing lt CLR gt lt D gt lt 9 gt lt 5 gt lt 1 gt lt ENT gt on the external keypad while the GS 1085 is in Idle Mode At the Password prompt enter the command mode password followed by lt ENT gt The default command mode password is 1085 Press lt A gt or lt B gt until Card Reader Setup is displayed Press lt ENT gt to access Card Reader settings While in this Command Menu the following options are accessed by using the A and B keys to scroll to the item then the ENT key to select that item Set Card type to Accept Press the A or B to select Both Cash
3. a Service Mode Service Mode is initiated by pressing lt CLR gt lt D gt lt 9 gt lt 5 gt lt 1 gt lt ENT gt on the external keypad while the 1085U is in Idle Mode At the Password prompt enter the Service mode password followed by lt ENT gt The default command mode password is 1086 In Command Menu Mode there are 3 Service Menus available 1 Read Meters via LCD Display 2 Print Meters using Com 1 3 Clear Meters Pressing the ENT key will allow access to the Service Menu selected Pressing A or B will advance to the previous or next Service Menu prompt While a prompt is displayed pressing CLR will back out one level Read Meters Service Mode is initiated by pressing lt CLR gt lt D gt lt 9 gt lt 5 gt lt 1 gt lt ENT gt on the external keypad while the GS 1085 is in Idle Mode At the Password Prompt enter the service mode password followed by lt ENT gt The default service mode password is 1086 Press lt A gt or lt B gt until Read Meters is displayed Press lt ENT gt to read the meters via the LCD display Total Cash In Display reads NNN NN indicates the amount of cash received since the meters were last cleared Press ENT for next meter 1 Bills Display reads NNNN indicates the number of 1 bills received since meters were last cleared Press ENT for next meter 5 Bills Display Reads NNNN indicates number of 5 bills received since meters were last cleared Press ENT for next meter 1
4. any need you may have Whether it s sales information a service requirement or just general inquiry you can be assured of a prompt response to your need s SALES If you are a new or existing customer with a new installation in mind our highly qualified sales staff can custom tailor a product solution for your particular needs Simply telephone GoPrint in the United States at 1 888 52 PRINT and ask for sales assistance You may also email us at sales goprint com UNITED STATES GoPrint Systems Inc One Annabel Lane Suite 105 San Ramon CA 94583 Tel 1 888 52 PRINT Fax 1 925 790 0071 SERVICE If you require technical assistance advice or parts please contact our support department at 1 888 52 PRINT or email us at support goprint com Repairs should be sent to GoPrint Systems Inc One Annabel Lane Suite 105 San Ramon CA 94583 Tel 1 888 52 PRINT ext 30 Fax 1 925 790 0071 Please visit us at htto Awww goprint com Copyright 2007 GoPrint Systems Inc All Rights Reserved 3 OPRINT Quick Reference Set Up Guide You will need a keypad which typically While unit is powered off plug the keypad has one per shipment This keypad into the top left main board inside the GS detaches and should be kept in a safe 1085 This is located in the very back of place the unit Step 1 Programming the Unit for the first time After plugging in the Keypad power up the Cash to Card Machine 1 2 3 On the
5. test it in another device e Ensure that the card reader is clean clean with cleaning cards available from GoPrint e Ensure that the card settings on the 1085 match the locations cards e Refer to the Error code list for specific error information Copyright 2007 GoPrint Systems Inc All Rights Reserved 22 GoPrint Card Error Codes Here is a list of common error codes amp their descriptions that may be encountered in the GS 1085 Error 1 e Check for jammed card e Check for sensor blockage i e dust or paper e Check for mechanical problem not allowing card to be taken in Error 2 e Reader thinks card is blank was card inserted in proper direction Try alternate card e Bad head connection at head e check head connection at sideboard e check head is it dirty worn or mis aligned Error 3 e STX Code error verify settings of STX and ROM under Card reader set up Error 4 e ROM Code error verify settings of STX and ROM under Card reader set up Errors 5 6 7 e Check condition of card Is it scratched bent or worn e Try alternate card in Reader e Check head alignment and cleanliness e Ensure drive roller and an idler roller are properly aligned in the card transport Error 8 e Card is flagged due to power interruption Re encode the card Error 9 e Site Code error verify settings of Site 3 under Card reader set up Copyright 2007 GoPrint Systems Inc All Rights Reserved
6. 0 Bills Display Reads NNNN indicates the number of 10 bills received since the meters were last cleared Press ENT for next meter 20 Bills Display Reads NNNN indicates the number of 20 bills received since the meters were last cleared Press ENT for next meter NOTE only bills that can be accepted will be displayed Value added to Display Reads NNN NN Indicates Dollar Value added to cash cards since meters were cleared Press ENT for next meter Value added to U Display Reads NNNNN indicates the Value added to Units cards since meters were last cleared Press ENT for next meter Cards Dispensed Display reads NNNNN indicates number of cards dispensed since meters were last cleared Press ENT for next meter Value not issued Display reads NNN NN indicates the Value not issued caused by card dispense failure or write failure since the meters were last cleared Press ENT for next meter Danyl Value Conv Display Reads NNN NN indicates the Value of cards converted from Danyl Format since meters were last cleared Press ENT for next meter Copyright 2007 GoPrint Systems Inc All Rights Reserved 15 GoPrint a Service Mode Read Meters Contintued Danyl num Conv Display Reads NNN indicates the Number of cards converted from Dany Format since the meters were last cleared Press ENT for next meter Grand Cash In Display Reads NNN NN indicates the total amount of cash received since it was built Grand tot
7. GoPrint GS 1085 Cash Card Loader May 2007 GoPrint a Table of Contents SALES AND SERVIC Eiiincivsccicccisciciveiecesscsnscssictescivacidvndecuodvundvetedeuodaedvoasveadsdaedvauseuin ceuuedsuudeddedvuiautveaudderddesbucevaas 3 QUICK REFERENCE SET UP GUIDE cecceeeeeee eee eee eee eeeeee eee RER eee eeaeeeeeeeeaeeeeseesaeeeeseeneneenees 4 FUNCTIONAL VUE 6 INSTALLATION SETUP iciccicisniicss csaseccssecssveuscsecaaeveedeutesecteeseussdueedasuvvatdvaadcndvensarwiucevvduviediunseucewuseruuesvwoaducadius 8 IDENTIFYING THE COMPONENT 0 ccseecsseesseeeseneesee seen eeeesseeesseeesaeeeseeseseeseaeseeaeesonessnedseessenesanesonenseeesans 9 SETUP THROUGH COMMAND MENU MODE ccccceeeceteeeeeeesneeeseeeseeeeeeeseeeeeecaeeseesseeesenaasenseeeeeecueenseesones 10 SERVICE MODE PRINTING READING CLEARING METERS cccsecsseessereeeeeeeseesenesseeeseenseesneenensees 15 ON Mr ei 19 BILL ACCEPTOR EI UI 20 FREQUENTLY ASKED QUESTIONS 0 cccceseeeeete essen eecees sees seeeeeeesecae eee seeaeesenesseeesaeeeseeeesoeseseeesonesoneesenessnes 22 CARD ERROR CODES ccccseeeeeteeeeneeeenee sees enee sense ene s eae eeaeesaeeaaeeegeeeg sees anes gags caeseanessaesaeesaeedaeesannesaeenseeaenes 23 Copyright 2007 GoPrint Systems Inc All Rights Reserved 2 GoPrint Sales and Service At GoPrint complete customer satisfaction is our number one goal As such customer support is readily available to satisfy
8. Setup Allows the setting of Card parameters site codes etc 5 Diagnostics Factory Use Only Pressing the ENT key will allow access to the settings for the Command Menu selected Pressing A or B will advance to the previous or next Command Menu prompt While a prompt is displayed pressing CLR will back out one level Command Mode Terminal Setup Command Menu Mode is initiated by pressing lt CLR gt lt D gt lt 9 gt lt 5 gt lt 1 gt lt ENT gt on the external keypad while the GS 1085 is in Idle Mode At the Password Prompt enter the command mode password followed by lt ENT gt The default command mode password is 1085 Press lt A gt or lt B gt until Terminal Setup is displayed Press lt ENT gt to access Terminal Settings Copyright 2007 GoPrint Systems Inc All Rights Reserved 10 GoPrint a Command Mode Terminal Setup Continued While in this Command Menu the following options are accessed by using the A and B keys to scroll to the item then the ENT key to select that item Set Date Enter the date via the keypad in the format yy mm dd Followed by ENT Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Set Time Enter the Time via the keypad in the format hh mm ss Followed by ENT Press ENT to confirm NOTE the hour is set in 24 hour format 1 12 1 12 AM 13 23 1 11 PM Pressing Enter before entering a new setting will leave the setting uncha
9. allow a card to be purchased If the cards are installed incorrectly the message Sorry unable to dispense cards will be displayed Refer to the Card Dispenser documentation for further details Card Reader Cleaning Over time the magnetic read write head and drive rollers in the Card Reader will accumulate with dirt Regular cleaning of these components can save down time and prolong their life The GoPrint Cleaning Card Part 40 50 CR 50 or 40 80 CR 80 should be used to clean the reader every month depending on the environment and volume of use Please contact GoPrint Systems at 888 52 PRINT to order Copyright 2007 GoPrint Systems Inc All Rights Reserved 8 GoPrint Identifying the Components CARD BILL DISPENSE ACCEPTOR o III Copyright 2007 GoPrint Systems Inc All Rights Reserved GoPrint a Setup through Command Menu Mode Before using the GS 1085 Cash Card Loader it must be set up according to the customer s site and operational requirements The command menus follow a common structure throughout the setup Keypad Function lt A gt Changes the current selection up one level used to move through menus and select options or settings Also used for Alpha Entries press for CAPITALIZED characters press again to advance alpha character until desired character is displayed then press lt ENT gt lt B gt Changes the current selection down one level used to move through menus and s
10. als are Non Resettable Press ENT for next meter Grand Add to Display Reads NNN NN indicates total amount added to Cash cards since the 1085 was built Grand totals are Non Resettable Press ENT for next meter Grand Add to U Display Reads NNNNN Indicates total amount added to Units cards since the 1085 was built Grand totals are Non Resettable Press ENT for next meter Grand Cards Dispensed Display reads NNNNN indicates total number of cards dispensed since the 1085 was built Grand totals are Non Resettable Press ENT for next meter Grand not issued Display Reads NNN NN indicates the Value not issued caused by card dispense failure or write failure since the 1085 was built Grand totals are Non Resettable Press ENT for next meter Press ENT for next meter Grand Danyl Value Conv Display Reads NNN NN indicates Value of cards converted from Danyl Format since the 1085 was built Grand totals are Non Resettable Press ENT for next meter Press ENT for next meter Grand Danyl num Conv Display reads NNN indicates Number of cards converted from Danyl Format since 1085 was built Grand totals are Non Resettable Press ENT for next meter Press ENT for next meter Print Meters Service Mode is initiated by pressing lt CLR gt lt D gt lt 9 gt lt 5 gt lt 1 gt lt ENT gt on the external keypad while the GS 1085 is in Idle Mode At the Password prompt enter the service mode password followed by lt ENT gt The defa
11. alue of Dispensed card equals the value on the cards sitting in the dispenser This is a predetermined amount by the customer usually 50 Press Enter Enter the Value on the cards using the number pad press enter to save Scroll to Dispenser Inventory and press enter NOTE this feature is only necessary for customers who wish to take meter readings from the unit No need to set it if they don t want meter readings Enter the number of cards in the dispenser using the number pad if using this feature Press Enter to save Note sites doing a conversion or using units follow slightly different set up instructions Contact GoPrint Hardware Support for information Copyright 2007 GoPrint Systems Inc All Rights Reserved 5 GoPrint a Functional Overview Power up The card reader and bill acceptor are always required for normal operation and are checked for normal communications when the unit is powered up Other installed peripherals are also checked if they are enabled An Out of Order warning will appear on the display if the key features are not responding The GS 1085 will display status messages during power up to indicate the firmware version and the progress of the above tests The GS 1085 has five modes of operation 1 Idle mode 2 Value Load mode if a dispenser is enabled 3 Dispensing mode 4 Command mode 5 Service mode Idle Mode This is the normal mode of operation after power up This
12. ar credit has been established 9 Check the bill box to see that the one dollar bill is properly stored ABOUT THE CONFIGURING OPTIONS The eight different configuration options and the order in which they are stored in the bill acceptor are as follows I accepted with high security disable 1 5 accepted with high security disable 1 55 10 accepted with high security disable 1 585 310 20 accepted with high security disable I accepted with high security enable 1 5 accepted with high security enable 1 5 10 accepted with high security enable 1 5 10 20 accepted with high security enable Configuring the bill acceptor for bill enabling and security is accomplished using the anti cheat lever and the illuminated inlet The anti cheat lever is used to enter configuration programming mode scroll through all possible configuration options and select the required configuration The illuminated inlet provides feedback to the user during the configuration process by displaying a pattern that corresponds to cach configuration option available Options available for BP4 only Copyright 2007 GoPrint Systems Inc All Rights Reserved 20 OPRINT SETTING THE CONFIGURING OPTIONS Remove the lower housing See Figure 1 Depress and release the anti chcat lever five times holding it down for a half a second cach time Once in the configuration mode depress and release the anti
13. changed Set Command Mode Password Enter the password to allow access to command mode via the keypad in the format Followed by ENT Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Set Service Mode Password Enter the password to allow access to Service mode via the keypad in the format Followed by ENT Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Command Mode Set Bills Command Menu Mode is initiated by pressing lt CLR gt lt D gt lt 9 gt lt 5 gt lt 1 gt lt ENT gt on the external keypad while the GS 1085 is in idle mode At the Password Prompt enter the command mode password followed by lt ENT gt The default command mode password is 1085 Press lt A gt or lt B gt until Set Bills is displayed Press lt ENT gt to access bills settings Copyright 2007 GoPrint Systems Inc All Rights Reserved 11 GoPrint Command Mode Set Bills Continued While in this Command Menu the following options are accessed by using the A and B keys to scroll to the item then the ENT key to select that item Set Accept 1 00 Press the A or B to select Yes or No Followed by Enter to control the acceptance of 1 00 Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Set Accept 5 00 Press the A or B to select Yes or No Followed by Enter to control the acceptance of 5
14. e a card to be dispensed and the display will read Please Remove Card The GS 1085 will then return to Idle Mode Command Mode To enter the administrative features or the Command Mode press from the keypad lt CLR gt lt D gt lt 9 gt lt 5 gt lt 1 gt lt ENT gt Enter the command mode password followed by lt ENT gt Default command password is 1085 lt ENT gt OR Enter the Service mode password followed by lt ENT gt Default service password is 1086 lt ENT gt Command and Service menus are detailed later in this document Copyright 2007 GoPrint Systems Inc All Rights Reserved 7 GoPrint Installation Setup With the GS 1085 Cash Card Loader your customers can purchase cards and add value to their cards on a self serve basis In order to use your Cash Card Loader a few simple installation steps are required Mounting The Cash Card Loader is small and light enough to be mounted directly onto a solid wall concrete block wood etc Mounting the GS 1085 on drywall is not recommended There are holes in the back of the case which will facilitate required mounting hardware For convenience the AC supply may be mounted internally or Externally depending on the site requirements WARNING Failure to securely mount the GS 1085 Cash Card Loader can result in injury or damage due to tipping or dropping Power Requirements The Cash Card Loader is equipped with a 24 Volt AC power supply which featur
15. elect options or settings Also used for Alpha Entries press for lower case characters press again to advance alpha character until desired character is displayed then press lt ENT gt lt ENT gt Selects the current selection or option used to move through menus and to save options or settings to memory lt CLR gt Clears the current value or steps back one menu item used to move through menus and to clear values when setting options or settings lt 0 gt lt 9 gt Used for Numerical Entry press the appropriate key for desired digit lt C gt Used for Alpha Entries press for Back Space lt D gt Used for Punctuation Entries press for Punctuation characters press again to advance character until the desired character is displayed then press lt ENT gt Command Mode Command Mode is initiated by pressing lt CLR gt lt D gt lt 9 gt lt 5 gt lt 1 gt lt ENT gt on the external keypad while the GS 1085 is in Idle Mode At the Password prompt enter the command mode password 1085 followed by lt ENT gt The default command mode password is 1085 In Command menu mode there are 5 Command Menus available 1 Terminal Setup Allows Date Time amp Active Peripheral to be set 2 Bill Acceptor Setup Allows the setting of Bill parameters 3 Coin Acceptor Setup Allows the setting of Coin parameters Only applies if unit is fitted with a coin acceptor and it is enabled 4 Card Reader
16. es an integrated 6 foot power cable and a plug The use of long extension cords and plugging into the same circuit as other heavy equipment vending machines photocopiers etc is not recommended These situations can introduce noise and voltage drops which may cause intermittent operational problems with the GS 1085 WARNING Failure to properly connect the power plug into an approved grounded outlet can result in injury or death The power supply is protected by an internal fuse for safety The Power supply is a sealed non serviceable unit Under no circumstances should the Power Supply case be opened There are no user serviceable parts within the power supply and modifications should not be attempted Attempting to repair modify or adjust the power supply could result in fire injury or death Bill Acceptor Settings The bill acceptor is set up for normal use when you receive the Cash Card Loader The bills accepted can be individually enabled or disabled in the Command menu Set Currency Refer to the bill acceptor documentation for details on other options Card Dispenser Remove any packaging material from the card dispenser Fill the dispenser with cards orientation is not important but customers usually like to see the card dispensed Face up Place the l shaped weight on top of the stack of cards If the cards were loaded properly and the card dispenser is enabled in the Command menu in Idle Mode the GS 1085 will
17. ess ENT to confirm Sites 1 2 and 3 must have different settings with the exception of 4095 Pressing Enter before entering a new setting will leave the setting unchanged Set Site 2 Enter the value for site code 2 via the keypad in the format Followed by ENT Press ENT to confirm if there are no additional codes the number is 4095 Sites 1 2 and 3 must have different settings with the exception of 4095 Pressing Enter before entering a new setting will leave the setting unchanged Set Site 3 Enter the value for site code 2 via the keypad in the format Followed by ENT Press ENT to confirm if there are no additional codes the number is 4095 Sites 1 2 and 3 must have different settings with the exception of 4095 Pressing Enter before entering a new setting will leave the setting unchanged Copyright 2007 GoPrint Systems Inc All Rights Reserved 13 GoPrint a Command Mode Card Reader Setup Continued Set Sites d4 to d10 Enter the value for site d X using the keypad in the format Followed by ENT Press ENT to confirm 1 4095 where 4095 no site code assigned Setting these sites will allow conversion of up to 8 Danyl site codes to ITC card format if the Convert function is enabled and the appropriate site codes are set Pressing Enter before entering a new setting will leave the setting unchanged Copyright 2007 GoPrint Systems Inc All Rights Reserved 14 GoPrint
18. keypad type in the code D 9 5 1 ENT Password is 1085 ENT Scroll using A amp B keys to Set Currency and hit Enter Turn on or off the 10 20 bill as requested by customer Hit Enter when making any changes by default both denominations are on When finished hit Clear once Scroll down to Reader Setup and hit Enter Scroll to Max Card Value and hit Enter Change the default of 100 to 50 or other value requested by the customer Hit Enter to save changes Scroll to card format amp hit Enter Change to ACT ITC and hit Enter to save changes Scroll to STX and hit Enter Make sure this says 12 if it does hit enter if it doesn t press 12 on the number pad and hit Enter Scroll to ROM hit Enter ROM Should be 6 if it is hit enter if it isn t press 6 on the number pad and hit enter Scroll to Card Site 1 hit Enter Using the number pad type the site code for the campus location this number is previously assigned and can be found on the site code doc Hit Enter To Save If more than one site code then repeat this step on Card Site 2 etc When finished Press Clear Once 6 Scroll down to Dispenser Setup and press Enter Scroll to Card Price and hit Enter Make sure this Reads 1 00 if not change using the number keypad Press Enter to save Scroll to Max Escrow press enter Copyright 2007 GoPrint Systems Inc All Rights Reserved 4 GoPrint a Change from Default of 5 to 1 00 Press Enter to save Scroll to V
19. l P bills box push tab gt in the direction of the arrow and slide the bill box up To service lower housing push tab on bottom up and pull to the rear FLASH CODES The BillPro supports the following flash codes for troubleshooting the unit in the field Flash Code Error Condition Check Bill Box Check Clean Bill Box Return For Service NOTE A scrolling light in the illuminated inlet indicates a normal operation If all LED s are not illuminated then the unit has been disabled by the VMC Figure 2 Coinco Publication No 925412 11 02 Printed in the U S A 21 GoPrint a Frequently Asked Questions The LCD display is Blank e Check that the 1085 is plugged into a Live power Outlet e Check that the power supply is attached to J8 AC In on the main board e Check that the fuse on the main board is not blown The Display Indicated unable to dispense cards e Ensure that a supply of cards are properly loaded in the dispenser chute e Ensure that the card weight is installed on the card stack e Ensure that the cables between the Dispenser main and auxiliary power board are properly affixed How and when should the bill Acceptor be cleaned e Refer to the section Bill Acceptor Maintenance in this manual How and when should the Card Reader be cleaned e Refer to the section Card Reader Maintenance in this manual When a card is inserted an error code is displayed e Ensure that the card being tried is good
20. lly by manipulating the gears and rollers Press up on the roller at the bottom of the Reader and turn both it and the gears back and forth until the card comes clear Sometimes it is necessary to push a small screwdriver blade up into the card near the hole for the head and rollers to release a badly bent card Bill Acceptor Maintenance The bill acceptors used in the GS 1085 series have proven to be dependable units Occasional servicing may be necessary Please refer to the appropriate Bill Acceptor Operation and Service Manual Copyright 2007 GoPrint Systems Inc All Rights Reserved 19 OPRINT Bill Acceptor Manual coinco BillPro Series Bill Acceptor Installation amp Operation BP2 amp BP4 Guide Multi Drop Bus Unit INTRODUCTION The BillPro Series Bill Acceptor is the result ofextensive rescarch and development in computerized crediting systems These greatly simplified units provide many important features never before available in any bill acceptor The BillPro Series Bill Acceptor extends the capability of the vending machine to generate maximum performance This page contains general information on installing operating and maintaining the BillPro Some of the units many outstanding features include Modular design with new routines and validation techniques that simplify future upgrades and expan sion Improved Bill Rejection Anti Jam Software Single harness with quick disconnects fo
21. mode waits for keypad entry or card insertion Insert Card Then Insert Cash If the dispenser is enabled this message alternates with To Purchase a Card OR To Purchase a Card Press Button Insert 1 00 bill Value Load Mode If a card is inserted into the reader while the system is in Idle Mode the Value Load mode is initiated Insert Cash Card lt balance gt Where lt balance gt current card balance The display alternates every 2 seconds with To remove Card Press Button When a bill or coin is inserted it is checked for both validity and value to ensure that the card will not exceed the MaxCard setting The following message is displayed for 2 seconds Copyright 2007 GoPrint Systems Inc All Rights Reserved 6 GoPrint GS 1085 Functional Overview Continued Accepted x The value is added to the card value If the card is a units card the bill value goes through the units per dollar conversion before adding to the card At any point the Eject Button can be pressed to end the transaction which will cause the system to add the new value to the card and release it back to the customer Dispensing mode When the GS 1085 is in dispensing mode the display will read To Purchase Card Insert 1 Bill e The Dispensing mode is cancelled after 2 minutes if money is not inserted e Inserting any bill other than 1 will cause the bill to be rejected Inserting a 1 bill will caus
22. nged Set ID Enter the identification number for the 1085 via the keypad in the format Followed by ENT Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Set Coin Installed Press the A or B to select Yes if the 1085 has a coin acceptor Followed by Enter Press the A or B to select No if the 1085 has no coin acceptor Followed by Enter Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Set Bill Installed Press the A or B to select Yes Followed by Enter if the 1085 has a bill acceptor Press the A or B to select No Followed by Enter if the 1085 has no bill acceptor Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Set Dispenser Installed Press the A or B to select Yes Followed by Enter if the 1085 has a card dispenser Press the A or B to select No Followed by Enter if the 1085 has no card dispenser Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Set Button to Dispense Press the A or B to select Yes Followed by Enter if the customer is to press the button to select card dispense mode Press the A or B to select No Followed by Enter if the 1085 is to automatically enter card dispense mode if money is inserted while no card is in the reader Press ENT to confirm Pressing Enter before entering a new setting will leave the setting un
23. only or Units only Followed by Enter to control the card type acceptance Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Set Max Value Cash Enter the maximum allowable Cash card value via the keypad in the format followed by ENT Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Set Max Value Units Enter the maximum allowable Units card value via the keypad in the format followed by ENT Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Copyright 2007 GoPrint Systems Inc All Rights Reserved 12 GoPrint a Command Mode Card Reader Setup Continued Set Units per Dollar Enter the number of Units to credit the card per dollar deposited via the keypad in the format Followed by ENT Press ENT to confirm 1 100 Pressing Enter before entering a new setting will leave the setting unchanged Set Display tenth cent Press the A or B to select Yes or No Followed by Enter to control the display of the tenth of a cent 0 00X for Cash card values Press ENT to confirm Pressing Enter before entering a new setting will leave the setting unchanged Set Card format Press the A or B to select the appropriate card format Followed by Enter The formats are ITC ACT ICX XCP VCS Danyl requires special Card reader chassis Press ENT to confirm Pressing Enter before en
24. r case of service Plastic PCB s Printed Circuit Board enclosure assures protection from water damage MDB Multi Drop Bus interface only New Flex Stacker maximizes bill capacity BP2 accepts old and new 1 and 5 s BP4 accepts old and new 1 5 10 and 20 s coupon capabilities are also available for both models Improved anti cheat features Compact design proves easy machine installation New configuration features eliminates the dipswitch INSTALLATION AND OPERATION Remove the vending machine s power 2 Install the BillPro Series bill acceptor into the mounting hole of the vending machine using the appropriate hardware NOT INCLUDED 3 Connect the BillPro Series interface harness to the vending machine NOTE Should additional mounting hardware be required please contact your local Coinca office or machine manufacturer 4 Restore power to the vending machine illuminated inlet will begin to flash and stacker motor will cycle upon power up tn Observe that the power indicator light on the back of the lower housing is ON continuously Ifthe light is off or blinking check the following Power to machine Machine disabling unit Bill acceptor harness Machine does not have credit already established 6 With the vend price set below one dollar insert a one dollar bill 7 Verify that a dollar bill is accepted and stacked into the bill box amp Verify a one doll
25. tering a new setting will leave the setting unchanged Accept Danyl Press the A or B to select between NO Convert to site 1 Convert to site 2 Cards that are converted to ITC format will be tracked in the meters Pressing Enter before entering a new setting will leave the setting unchanged Setting the STX and ROM A two nibble four bit code forms part of the overall facility code This has typically been referred to as the ROM code for the site The first nibble of this ROM code has typically been referred to as the Start first nibble STX Each nibble of the two nibble ROM code can have a value from 0 to F in hexadecimal notation which is 0 to 15 in decimal notation The values set in the 1085 must be in decimal notation I E ROM Code of B9 The STX nibble is B 11 and the ROM nibble is 9 9 For GoPrint the STX is 12 ROM is 6 Set Card STX Enter the Card STX via the keypad in the format 12 for GoPrint Followed by ENT Press ENT to confirm 0 15 Pressing Enter before entering a new setting will leave the setting unchanged Set Card ROM Enter the Card ROM via the keypad in the format Followed by ENT 6 for GoPrint Press ENT to confirm 0 15 Pressing Enter before entering a new setting will leave the setting unchanged Set Site 1 Enter the value for site code 1 using the keypad in the format Followed by ENT this number is unique for each location Pr
26. ters Service Mode is initiated by pressing lt CLR gt lt D gt lt 9 gt lt 5 gt lt 1 gt lt ENT gt on the external keypad while the GS 1085 is in Idle Mode At the Password prompt enter the service mode password followed by lt ENT gt The default service mode password is 1086 Press lt A gt or lt B gt until Clear Meters is displayed Press lt ENT gt then at the Prompt Clear Meters C Yes Press the C key to clear the meters Any other key will leave the meters intact Copyright 2007 GoPrint Systems Inc All Rights Reserved 18 GoPrint a Maintenance General Maintenance The lock shaft should be kept lubricated with Lithium grease to ensure easy opening and closing The outer metal can be cleaned with a mild household cleaner such as window cleaner The use of cleaners with abrasives is not recommended as they could scratch the housing The Plastic LCD display cover should be cleaned with a soft rag moistened with water or isopropyl alcohol Check the condition of the Power supply cable and replace immediately if any damage is observed Card Reader Maintenance The Card Reader in the GS 1085 is the universal Serial Insert Reader and is cared for in the same way as any other Card Reader The head and rollers should be kept clean with GoPrint Systems Cleaning Cards 40 50 or 40 80 Any dirt or loose bits of paper impeding the sensors should be blown out with canned air Severe card jams can be removed by manua
27. ult service mode password is 1086 Press lt A gt or lt B gt until Print Meters is displayed Connect a serial device Printer or PC to Com 1 of the GS 1085 Set the serial device for 9600 baud no parity and 1 stop bit When the device is online press lt ENT gt to send the meters to the device Copyright 2007 GoPrint Systems Inc All Rights Reserved 16 OPRINT Service Mode Print Meters Continued Sample Meters Print out Meters Report for Unit 1234 06 08 09 11 38 01 Total Cash Collected 00 1 Bills Collected 5 Bills Collected 10 Bills Collected 20 Bills Collected Value added to cards 000 Value added to U cards 0 Number of cards dispensed 0 Value not issued 000 Not Issued Database CO OO OCH Danyl value converted 00 000 Danyl num cards conv 0 Grand Total Cash in 00 Grand added to cards 000 Grand added to U cards 0 Grand Total Num cards dispensed 0 Grand Total Value not issued 000 Grand Total Danyl value converted 00 000 Grand Total Danyl num cards conv 0 Grand Total Clear meters 0 End of report Copyright 2007 GoPrint Systems Inc All Rights Reserved 17 OPRINT Service Mode Print Meters Continued Cable to PC Computer a 5 9 00 o ho w 00 co DS2 Socket Female D89 Pin male Cable to Printer 1085 Printer COM 1 PTR ho SN Go 60 coy in DB9 Pn male DB9 Pn Male Clear Me
Download Pdf Manuals
Related Search