Quick Set-Up Guide
Contents
1. Quick Set Up Guide f Read Prior to Use 7 40SELECT Intelligent Monitoring Defined T ei e ts 1 Remove the plastic bag and monitor screen protector 2 Place the 740SELECT monitor and accessory box on a secure tabletop 3 The 740SELECT is shipped with the Li ion battery installed Open the 740SELECT standard accessory box and review contents 1 Identify the monitor part number located on the monitor rear label 2 Verify packout table below Part Number NIBP SpO2 Temp Standard 01 02 1000 1 4 01 02 1001 1 2 4 01 02 1002 1 2 4 01 02 1003 1 2 3 4 01 02 1004 1 2 3 4 01 02 1009 1 3 4 01 02 1013 2 3 A 01 02 1014 2 3 4 01 02 1015 2 4 01 02 1016 2 4 Pack Out Description 1 NIBP 4 Standard BP start up kit e Power supply 2 SpO2 e Power cord e User manual addendums e SpO2 patient cable and field service manual on CD e Quick reference guide monitor operation e SpO2 sensor e SpO2 sensor start up kit 3 Temp e FILAC 3000 isolation chamber e FILAC temperature probe e 1 box of temperature probe covers The following accessory item s may be placed in the monitor pack out if purchased with the monitor Masimo CO2 e ISA CO2 start up kit e IRMA CO start up kit CO2 Analyzer Accessory e ISA CO2 holster e ISA CO2 clamp adapter ISA CO2 modura holder SpO2 The SpOz connector left hand side and monitor input panel are keyed to assure proper orientation2. MAXNIBP Male NIBP Connector 1 Align the SpO2 connector and push into the input panel until the connection is seated The connector is properly seated when you hear a click 2 Complete the cable connection to the SpO2 patient sensor Note The Microstream Micropod start up kit cradel and clip or cradle and VESA mount may be packaged separate from the monitor NIBP hose connection CASMED MAXNIBP 1 Remove the BP hose from the BP start up kit 2 Align the female NIBP hose connector and push onto the male connector You will hear a click when the connection is properly seated 3 Gently pull on the BP hose to verify proper connection Movement between the BP hose and connector is normal The connection is designed to allow the hose to move slightly in and out and rotate while maintaining a secure connection 4 Press the gray button to release the hose from the NIBP connector Assemble Covidien FILAC 3000 Temperature probe and chamber 2 Position the isolation chamber as shown 1 Locate the FILAC 3000 Temperature probe L shaped connector 4 Slide the connector up and into the slot 3 Align the top of the temperature probe until fully seated you will hear a click L shaped connector to the slot 5 Insert the temperature probe into the temperature probe well as shown FILAC 3000 isolation chamber Insert isolation chamber and probe into the side car 740SELECT models 01 02 1003
3. and 1004 Well for Isolation chamber 1 Insert the 3 Three alignment tabs i assembled probe should be engaged Fz e temperature probe and isolation and seated into the solation chamber chamber into the side car 1 2 3 v temperature i Temperature dect 4 Push the isolation 5 verity that the aN chamber down into isolation cham 2 Align the probe well and slide into the side car the side car until ia ber is fully seated you hear a click all around er Insert temperature probe covers into the isolation chamber 740SELECT models 01 02 1003 and 1004 1 Position the probe covers with the temperature probe access cover opening toward the front of the monitor gt Arrow icon on probe box 2 Insert the box of probe covers into the slot until you hear a click Connect the 740SELECT power supply and power cord Power cord connected to power supply 1 Connect the power cord to the power supply by fully inserting into the power supply lt be 2 Connect the barrel connector to the monitor 3 Connect the power cord plug to a wall outlet Power cord Barrel connector Turn the 740SELECT monitor on 1 Press the On Off power button located on the front panel to turn the monitor on e The On Off switch illuminates when the monitor is turned on e During boot up a configuration setup test and POST is performed automatically 20 25 seconds e Completion of the
4. test and POST is confirmed by a two beep audio alert 2 Verify the monitor battery charging LED is lit when plugged into wall outlet Recommend fully charging battery before entering into service e Reference 740SELECT user manual for operating instructions 44 East Industrial Road Branford CT 06405 USA 800 227 4414 www casmed com FILAC is a trademark of Covidien AG or an affiliate Masimo is a registered trademark of Masimo Inc ISA and IRMA are Masimo Inc trademarks Microstream is a registered trademark of Covidien Medical 1987 Ltd Micropod is a trademark of a Covidien company registered in the U S and foreign countries MAXNIBP is a registered trademark and 740SELECT a trademark of CAS Medical Systems Inc CASMED reserves the right to make changes to this document without notice 21 03 0340 Rev01
Download Pdf Manuals
Related Search