f3d3sp/f3d3p - Fast Food Service Norge
Contents
1. Frozen fry dispenser F3D3S F3D3 F3D3SP F3D3P Status 07 2012 Electrical connection F3D3 F3D3S 230V vov 230v mov Phases 1 Ph L N PE 1 Ph L N PE Power L3kW L3kW 13kW 13kW 50 amp 60 50 amp 60 Amperes 5 5 A Operating conditions and installation require ments Max ambient temperature 33 C Max humidity 60 Minimum rear clearance Minimum top clearance 100 mm Minimum side clearance None Energy consumption 24 h F3D3P F3D3SP 5 1 kWh Energy consumption 24 h F3D3 F3D3S 7 5 kWh Cooling system Closed system cold wall construction Refrigerant F3D3P F3D3SP R290 Refrigerant F3D3 F3D3S R404A Climate class Operating temperature 18 C to 23 C French fry capacity Up to 26 kg Up to 350 baskets Up to 700 baskets Dispensing rate per hour per hour Plus minus 1096 of the calibration weight for the large dosing quantity 60 Hz 11 0 A Q2 Dispensing accuracy Load size Dosing quantity for international calibration Small 0 75 Ib 340 g 0 75 Ib 340 g Medium 1 0 Ib 454 g 1 0 Ib 454 g Large 1 5 Ib 680 g 1 5 Ib 680 g Small 0 69 Ib 312 g 0 69 Ib 312 g Medium 0 92 Ib 418 g 0 92 Ib 418 g Large 1 38 Ib 625 g 1 38 Ib 625 g Load size D Small 417g Medium 500 g Large 625 g The dosing quantity calibration can be changed instructions on calibrating the dosing quantity can be found in the2. Do not touch the cooling lines while cleaning Wear suitable gloves while cleaning N NOTICE Appliance damage Rinsing with water that is too hot can deform the hopper s Clean the hopper s with lukewarm water only Components that are frozen together may damage the appliance Never place wet components into the freezer Carefully dry the components after cleaning Heavy objects may damage the basket wire racks and the drip pans Only place frying baskets on the basket wire racks and drip pans when the baskets are empty NOTICE Rust on stainless steel surfaces Abrasive cleaning agents and sharp objects cause iron residue that can rust Do not use abrasive cleaning agents steel wool brushes scrapers or other sharp objects for cleaning Use cleaning fleece made of artificial fibers to remove stubborn dirt Frozen fry dispenser F3D3S F3D3 F3D3SP F3D3P Status 07 2012 INSTALLATION F3D30P F3D3P F3D39 F3D3 The appliance must be installed by qualified specialists according to the manufacturer s instruc tions and building food and electrical regulations Locally applicable accident prevention regulations must be followed If accident prevention regu lations are not observed the manufacturer is released from any liability 1 5 TECHNICAL DATA WE E With gt gt gt D 2 w s s Electrical connection F3D3P FIDSSF gt gt
3. F3D3SP F3D3P Status 07 2012 Fig 07 Bucket with filler doors 4 2 DAILY CLEANING PROCEDURE NOTICE Appliance damage Rinsing with water that is too hot can deform the hopper s Clean the hopper s with lukewarm water only Components that are frozen together may damage the appliance Never place wet components into the freezer Carefully dry the components after cleaning Wash and disinfect all components taken out of the appliance in the rinsing sink one after the other Set all components upright to air dry Place the hopper upside down so the water can drain out of it After the appliance is fully defrosted Wipe off and disinfect the refrigerator and the bucket see Fig 07 with a cloth n particular wipe off and disinfect the front and back of the filler doors and the entire bucket Tip The filler doors of the bucket are spring loaded and can be opened by pushing on them carefully All parts of the bucket are more easily accessible for cleaning with the filler doors fully open Remove the lower drip pan wash it in the rinsing sink and set it upright to dry Wipe off and disinfect the entire basket wire rack area with the cross supports side walls and the rear wall using a cloth Thoroughly dry the interior and the basket wire rack area with a sterile cloth Close the freezer door Frozen fry dispenser F3D3S FSD3 F3D3SP F3D3P Status 07 2012 25 PREVENTIVE MAINTENANCE R
4. dispensed The load size cannot be changed on the The hopper is empty es hopper with fries Press Reset The filling process shake the hopper and redistribute the fries to break up the n a bridge Proceed carefully so as not to break the fries If nec together to form a bridge very m hard essary remove very hard clumps Press Reset The filling j process begins The bucket is missing Insert the bucket In the hopper the fries are baked The filler door motor is faulty Call technical customer service Fill the hopper with fries Attention If the machine continues dispensing until the hopper is empty the filling process is aborted and error message Err04 is displayed The filling level in the hopper is low only 3 4 fillings The frozen fries created a hollow space around the sensor in the hopper Shake the hopper and redistribute the fries to close the hollow space Proceed carefully so as not to break the fries The Low product sensor is soiled Clean the Low product sensor The Low product sensor is faulty Call technical customer service The deflector is missing from the siida imine delector hopper The deflector is damaged e Replace the deflector The deflector is a wear part and should cracked on the side be replaced in good time TRE eee ROME TS NOE COME GIN Take out the freezer bottom and insert it correctly positioned The basket symbol does not light Wait for
5. Service Manual 716 390 599 718 307 6097 718 390 030 718 387 300 718 390 091 718 390 586 718 390 051 718 390 586 Frozen fry dispenser F3D3S F3D3 F3D3SP F3D3P Status 07 2012 2 4 REMOVING THE PACKAGING BOX Risk of injury A tilt indicator is mounted on the shipping box The tilt indicator must show the correct display see Fig O1 Only unpack the appliance if the tilt indicator shows the correct display Do not unpack the appliance if the tilt indicator display is incorrect Contact technical cus tomer service Fig Of Tilt indicator Correct The ap pliance can be unpacked Incorrect The ap pliance must not be unpacked contact technical customer service Procedure The tilt indicator must show the correct display see Fig 01 Risk of injury The straps on the shipping box are under tension The wood of the pallet can splinter Keep an adequate distance when cutting the straps Wear gloves and goggles when unpacking Cut the plastic straps with scissors Lift off the packaging box with 2 people see Fig 02 Cut the plastic straps of the accessories box with scissors see Fig 03 The accessories box contains removable com ponents Do not discard a b Fig 02 Lifting Fig 03 Removing off the packaging the accessories box box Frozen fry dispenser F3D3S FSD3 F3D3SP F3D3P Status 07 2012 11 2 2 REMOVING THE PALLET Risk of injury The
6. appliance is very heavy top heavy and can easily tip Therefore the pallet is designed so the appliance can only be pushed forward off the pallet with the aid of 2 metal ramps Do not unpack the appliance alone The appliance should be unpacked by two or three people Do not try to push the appliance off the pallet sideways or toward the rear Get two people to grasp the appliance at both sides Carefully push the appliance forward Hold the pallet in place If necessary carefully shift the appliance back and forth see Fig 04 Pushing the appliance forward causes 2 metal ramps to be extended which can be used to push the appliance off the pallet without requir ing a fork lift Push the appliance down along the metal ramps until the front castors touch the ground Carefully push the appliance off the metal ramps until all 4 castors are on the floor Fig 04 Pushing the appli ance off the pallet 2 3 SETTING UP THE APPLIANCE The appliance must be set up horizontally The ventilation openings in the housing must be kept clear Note the minimum clearances see Technical data The setup location must be suitable for cleaning the appliance and for rolling it forward for rear access for maintenance The appliance is set up next to the frying station The following configurations are possible Configuration 1 Bagging station Deep fryers Configuration 2 Deep fryers Bagging station 12 Frozen fry di
7. for its intended purpose i e for the intermediate storage and filling of frozen products french fries Any other use is considered inappropriate IMPORTANT he appliance must only be operated by trained personnel Each operator of the appliance must have read and understood the user manual Children and people with restricted physical sensory or cognitive abilities must never be left alone with the appliance and must always be supervised Adhere to the maintenance and cleaning intervals Regular maintenance and cleaning pre serves the operating safety and performance of the appliance Give the user manual to the next owner if the appliance is sold or passed on to a new owner he appliance is not suitable for storing frozen products french fries for extended periods it is only intended as an intermediate storage location between the freezer room and the deep fryer Frozen fry dispenser F3D3S FSD3 F3D3SP F3D3P Status 07 2012 It may only be used for its intended purpose The appliance is not suitable to be set up and used outdoors It is intended for use In kitchens where it is protected against the weather excessively high temperatures and humidity and a corrosive atmosphere 1 4 SAFETY INSTRUCTIONS Risk of fatal injury from electric shock If the appliance is damaged or malfunctioning disconnect it from the power supply before per forming repair maintenance or cleaning work Adhere to the s
8. rack Ss Lower drip pan plastic Castors without brake Castors with brake Crumb Tray option F3D3S type label behind the air filter F3D3SP Type label 16 Frozen fry dispenser F3D3S F3D3 F3D3SP F3D3P Status 07 2012 F3D3 und F3D3P Dual Lane Compressor cabinet Access plates to condenser Warning and pro hibitory signs BR Control panels of the dispenser lanes Power switch Wire rack Hopper with drum Deflector rubber Handles for manually turning the drum Storage area for Freezer bottom unused baskets Upper basket wire rack with basket guides Lower basket wire rack SN Castors with brake Crumb Tray option F3D3S type label behind the air filter F3D3P Type label Frozen fry dispenser F3D3S FSD3 F3D3SP F3D3P Status 07 2012 17 BASKET symbol with 7 green LEDs When the BASKET symbol lights up the dispenser lane is ready to dispense the product into the frying basket Control panel for the dispenser lane There is one control panel for each dispenser lane The dispenser lanes can be operated sepa rately If necessary one of the dispenser lanes can be switched off FSD3P Dual Lane ATTENTION symbol with 3 LEDs at the corners Indicates the status of the dispenser lane Lamps are off The appliance is ready to operate Lamps light up Indicates a low filling level The appliance continues to dispense fries Lamps flash Indicates an er
9. steps 2 and 3 until the hopper s is are full see Technical data french fry capacity Fully tear open the bag hold Carefully pour the fries into ing the frozen fries Be careful the hopper from above being not to break or crush the careful that the fries do not fries break Hold the bag in such a way that most fries fall paral lel to the drum Close the freezer Frozen fry dispenser F3D3S FSD3 F3D3SP F3D3P Status 07 2012 21 Setting the load size The current load size is displayed at the bottom left of the screen e g small standard Press the ACTION 3 button The display changes to the next load size e g medium Press until the desired load size is displayed on the screen 22 Frozen fry dispenser F3D3S F3D3 F3D3SP F3D3P 3 4 DISPENSING FRIES NOTICE Loss in quality The product thaws quickly in the filled frying basket The filled baskets should not be stored on the storage areas of the frozen fry dispensers or on the deep fryer for long periods Only fill a basket if the deep fryer is ready to use Change the load size if neces sary The load size is set to small by default The appliance is ready to dis pense fries when the BASKET symbol lights up Ready appears on the screen Press the ON OFF button for 4 seconds until the button LEDs light up The dispenser lane is switched on Remove the filled basket and immediately place it into the deep
10. the BASKET symbol to light up The fries are now up dispensed ho Desc eges Take out the basket wire rack and insert it correctly tioned correctly The Err04 and Low product warn Fill the hopper with fries ing error messages appear The ACTION 3 button Reset See error 8 flashes MU Remove all fries from the filler doors doors The return spring of the filler door Close the filler doors manually If the filler doors open again by is broken themselves call technical customer service l l If the filler doors cannot be closed manually call technical The filler door sensor is faulty customer service The filling process is finished when the BASKET symbol LEDs light up and Ready appears on the screen The load size can now be changed The filling process is not yet fin ished operator panel Frozen fry dispenser F3D3S F3D3 F3D3SP F3D3P Status 07 2012 31 DECOMMISSIONING STORAGE DISPOSAL 71 STORAGE storage conditions The storage area must be dry and well ventilated Procedure Disconnect the appliance from the power supply Remove all food and beverages from the appliance Clean the interior and the accessories Using acloth apply a thin protective film of Vaseline oil onto the metal surfaces Leave the doors and drawers slightly open to guarantee good air circulation 7 2 DISPOSAL Risk of fatal injury from electric shock Ensure that the appliance is disconnected from the pow
11. the error message bridge Proceed carefully so as not to break the fries Press Err04 and the ACTION 3 Reset Reset The filling process begins button flashes The lifting mod ule does not go The lift motor is faulty Call technical customer service up or down The di l itched off Press the ON OFF button for 4 seconds until the button LEDs The basket e dispenser lane is switched off light up symbol does not j light up The required loading size was not See no 12 reached DAE mne process 15 anOrted pre Press Reset The filling process begins maturely In the hopper fries are baked together to form a bridge The screen displays error message The ACTION 3 button Reset flashes Shake the hopper and redistribute the fries to break up the bridge Proceed carefully so as not to break the fries Err04 and the ACTION 3 Reset button flashes 30 Frozen fry dispenser F3D3S F3D3 F3D3SP F3D3P Status 07 2012 The appliance does not dis pense the prod uct and error message Err04 is displayed The appli ance does not dispense the product and error message ErrO2 or ErrO7 is displayed The Low prod uct warning error message appears The hopper is empty but error message Err04 is not displayed The loading weights are permanently incorrect either too light or too heavy The filler doors do not open to dispense fries The filler doors do not close af ter the fries are
12. 22 2220 umque uM E A ERAL 221224 2 S 270007 uz only F3D3SP F3DS3P Frozen fry dispenser F3D3S FSD3 F3D3SP F3D3P Status 07 2012 3 4 IMPORTANT Before initial use the instructions on operating safety use and maintenance must be read care fully and understood Keep the user manual in the vicinity of the appliance for later reference 11 SYMBOLS FROM THE USER MANUAL gt D bP b gt P DANGER indicates a potentially hazardous situation which if not avoided may result in fatal or serious injury WARNING indicates a potentially hazardous situation which if not avoided may result in injury CAUTION indicates a potentially hazardous situation which If not avoided may result in minor or moderate injury NOTICE NOTICE indicates a situation which if not avoided may result in damage to the appliance Important information can be found here Additional information tips and recommendations can be found here Frozen fry dispenser F3D3S F3D3 F3D3SP F3D3P Status 07 2012 1 2 WARNING AND PROHIBITORY SIGNS Fire open flames and smoking is prohibited General warning Warning of flammable materials Access is prohibited to unauthorized persons Warning of dangerous electric voltage Maintenance and repair work by unauthorized persons is prohibited 1 3 PROPER USE This is technical equipment that is only intended for use in the food service industry The appliance may only be used
13. 34 06 220 Fax 0049 7761 5533 8700 Email carlo recchia franke com Email alessandro figus franke com G FCE_Engineering l00_user_manuals GM Frozen_fry_dispenser_F3D FrozenFryDispenserF3D_allversions indd E Em d United Kingdom Franke Foodservice Systems GmbH Unit 2A Broom Business Park Bridge Way Chesterfield S419QG UK Phone 44 0 1246 264 280 Fax 44 0 1246 264 288 Spain Franke Foodservice Systems GmbH Rodr guez San Pedro 2 6 Edificio Inter Oficina 603 28015 Madrid Spain Direct phone 34 91 367 63 64 Direct fax 34 91 406 13 78
14. D3SP F3D3P Status 07 2012 13 Cleaning the stainless steel surfaces NOTICE Rust on stainless steel surfaces Abrasive cleaning agents and sharp objects cause iron residue that can rust Do not use abrasive cleaning agents steel wool brushes scrapers or other sharp objects for cleaning Use cleaning fleece made of artificial fibers to remove stubborn dirt Clean the stainless steel surfaces with a moist cloth lukewarm water and neutral soap Wipe clean with clear water Wipe dry thoroughly Removing limescale deposits and lime stains If cleaning with a neutral soap is not sufficient limescale deposits can be removed with a 25 solution of vinegar Give the vinegar solution time to act rinse with clear water and wipe dry 14 Frozen fry dispenser F3D3S F3D3 F3D3SP F3D3P Status 07 2012 APPLIANCE DESCRIPTION The F3D3 is used to easily portion frozen fries without a loss in quality The semi automatic equipment ensures that filled frying baskets are made available according to need The F3D3 Dual Lane is particularly flexible due to the two separately operable dispenser lanes R404A or the environmentally friendly R290 is used as the refrigerant R290 has no damag ing influence on the ozone layer ODP a negligible greenhouse effect GWP and is available worldwide Because of its efficient energy properties R290 is highly suitable as a coolant for this application Special precautions must be taken into co
15. FROZEN FRY DISPENSER FSD3S F3D3 F3D3SP F3D3P Single Lane Dual Lane with R404A or propane R290 refrigerant Item no FOODSERVICE SYSTEMS 18 390 030 18 387 300 18 390 599 18 387 897 lt F3D3S Single Lane F3D3SP Single Lane 18 390 032 718 390 587 718 390 031 718 390 586 F3D3SP Single Lane F3D3P Dual Lane F3D3S Single Lane F3D3 Dual Lane C Franke Foodservice Systems As one of the world s leading providers of comprehensive kitchen solutions we support restau rant chains with efficient product developments and professional services We have stood for ex cellent quality and maximum flexibility for over 35 years More than 27 000 kitchen projects and services that make your daily work easier and more profitable are a measure of our success You have decided to purchase a product from Franke Foodservice Systems a great choice We would like to thank you for your trust and assure you that we will continue to do everything in our power to be an excellent partner Direct contact with you Is especially important to us That s why our expert staff are happy to support you Throughout the world Declaration of Conformity Franke Foodservice Systems Poland Sp Z o o declares under its sole responsibility that this these appliance s set forth in this declaration conform s to the regulations of these directives 2004 108 EC EMC Directive 2006 42 EC Machinery Directive The conf
16. G 6 1 ERROR MESSAGES The error messages are displayed on the control panel screen Fill the hopper with fries ATTENTION If the machine continues dispensing until the hopper is almost empty the filling process is interrupted and error message Err04 is displayed Filling level in hopper ts low enough for filling 3 to 4 baskets 1 Check the bucket and filler door module Bucket error 2 Press Reset ACTION 3 button 1 Fill with fries or 2 Check the hopper for clumped fries and release remove the bridge if necessary 3 Press Reset ACTION 3 button 1 The hopper is empty 2 There is a clump of fries bridge in the hopper The filler doors are 1 Check the filler doors for blockage blocked 2 Press Reset ACTION 3 button Load cell problem Call technical customer service 6 2 MALFUNCTIONS The power E Meri Ep A Connect the power connector switch on the power switch switch is switched on but Plug the connector into another socket Have the faulty power The power socket is faulty l i the freezer is not socket repaired by an electrician running E The fuse tripped Check if the fuse tripped Reset it if necessary Frozen fry dispenser F3D3S FSD3 F3D3SP F3D3P Status 07 2012 29 running but The filter is soiled Clean the filter See the Preventive maintenance chapter cannot reach the l l Clean the condenser ribs see the Preventive maintenance The
17. afety instructions on the appliance itself see figure such as on the power supply filter housing Do not connect the appliance to the power supply if the connection cable is damaged Have the damaged cable replaced with an equivalent cable by a qualified electrician Do not put the appliance back into service beforehand Never repair the appliance yourself Have the necessary repairs carried out by a qualified specialist with original spare parts Moisture on the electrical components can lead to a short circuit and to serious or even fatal injury on contact Never clean the appliance with a direct water jet a sponge or a high pressure water jet Never connect the appliance to the power supply while the appliance is wet Disconnect the appliance from the power supply immediately if the appliance becomes wet during operation Danger of fire The cooling circuit is filled with R290 propane Propane is highly flammable The cooling coils are contained in the side walls If the cooling coils are damaged highly flammable propane will escape An analysis or repair of the cooling system is only allowed under certain conditions Never repair the cooling system yourself f you experience problems contact the technical customer service The appliance may only be repaired by a refrigeration technician under certain conditions Read the chapter Maintenance repair only F83D3SP F3D3P 6 Frozen fry dispense
18. condenser ribs are soiled chapter required operat None of the measures taken ing temperature 18 C Take all products and components out of the appliance and de Ice formation on the inside walls l ps frost the appliance see the Cleaning chapter Recommenda especially on the temperature mE ae i tion To avoid ice formation do not keep the freezer door open eu longer than necessary Defrost daily The freezer is l l 2 a a pro erm a Call technical customer service cleaning of the filter and condenser ribs Switch on the power switch Start up the appliance see the Daily startup chapter No line power The dispenser Plug in the connector start up the appliance see the Daily procedure for starting up chapter The ON OFF button was not Press the ON OFF button for 4 seconds until the button LEDs pressed long enough light up The hopper s is are not properly Press the hopper into the appliance turning the drum at the engaged in the drum hub handle if necessary lanes cannot be switched on The freezer door does not close properly The hopper is empty The screen displays the error message Err04 Fill the hopper with fries Press Reset The filling process and the Action 3 Reset button begins flashes The drum does not turn In the hopper fries are baked together to form a bridge The shake the hopper and redistribute the fries to break up the screen displays
19. er supply Disassembly of the appliance must be performed by qualified specialists according to the manu facturer s instructions Follow the local safety regulations Dispose of the appliance in accordance with local regulations t is essential that you observe the laws and regulations for the disposal of environmentally harmful substances Obtain detailed information about their disposal such substances include refrigerants or plastics Before disassembly all food remnants must be removed and the appliance must be thoroughly cleaned 32 Frozen fry dispenser F3D3S F3D3 F3D3SP F3D3P Status 07 2012 special regulations apply when disposing of used electrical appliances The customer assumes responsibility for proper disposal of the delivered product after the end of its service life at the customer s own expense in accordance with legal regulations The customer releases Franke from the obligations under Section 10 Paragraph 2 of the German Electrical and Electronic Equipment Act ElektroG and claims by third parties in this connection The entitlement by Franke to be released by the customer is not subject to any statute of limita tions and ends after utilization with proper disposal by the customer If the product is passed on to a third party the customer must ensure that the disposal requirement is fulfilled upon the end of service life In the event that the customer requests disposal by Franke Franke GmbH will
20. esscccesssccassccceassecesecceaescceasscceascseassccesescesaesees 19 o Belore starting Up Tor the Trst OME s e arti Sane Ta oS DEx Han T Ee Xia RSEN ance X ERR Es ted or ERE NE 18 3 2 Daily procedure Tor starting up switehinge OI sc iaa e NEER S EANPERM ATE REA Y ERO a a 90A 49 60 6 19 Oo IE URS RERUMS 21 JH DEPEN NE THIS etes RENI ixmpN INANIS MD UMP EPIS 22 3 5 Daily procedure for decommissioning switching off sees 23 MERO RET TEE 24 Hel DEMOUN MT 24 42 Daily cleaning procedure connseaensanscentnasanandancsevanenuunnchieciaeavaansanseeinacwiacisamanauianaxwntss 29 5 Preventive maiM enaNG Eers E Ed MX teas E PONAM UNS NRI B UE 26 35 4 I WV OM NER 26 5 2 Cleaning the condenser ribs esses eene enne nnne seen essere senis 26 5 3 Customer service electric components cccccccsssccccesssceceeeseccceeeeecesaesesecseneecenes 27 5 4 Customer service cooling SYSteM ccccccccccccccicccciccccccccccicccciccecccieeaeeee 28 6 Malfunctions Troubleshooting 1 llle esee ee eee esee eee eene eene nnne nennen naar tree eese nnne 29 TEES i9 Si Rem 20 GZ MANE d ONE 2222220380000230 cad caedes teins sep pumesipue titia etes tu met estes E AAR siecle been DS RES 29 7 Decommissioning storage disposal 1 eee eee eee e esee ee eee eene eene e enne nnne een ane 32 A o 32 22 NNO ee 120 ENE A 22001 0100 1251
21. fryer The screen displays Filling The filling process is displayed on the screen by a growing Place an empty deep fryer horizontal bar basket under the dispenser and push it back against the dispensing pressure switch The basket is filled Status 07 2012 setting down the empty frying baskets NOTICE Appliance damage Heavy objects may damage the basket wire racks and the drip pans Only place frying baskets on the basket wire racks and drip pans when the baskets are empty Empty frying baskets can be set down on the Intended area in the appliance until they are refilled Lower basket wire rack 3 baskets ppo a Ai oa 2 1 baskets 2 2 baskets dispensing stations Side basket wire rack if present 3 5 DAILY PROCEDURE FOR DECOMMISSIONING SWITCHING OFF The appliance must be emptied defrosted and cleaned every day after closing Tip In restaurants with continuous opening hours the freezer should be switched off for 2 3 hours daily It is recommended to keep the filling quantity of the hopper relatively low before closing the restaurant for the day so that only a small quantity of fries needs to be kept in the freezer room overnight For a more convenient timing of the cleaning process the F3D3 F3D3P Dual Lane offers the option of switching off only one of the two dispenser lanes before closing for the day The com ponents can then be taken out of the appliance and cleaned 1 P
22. isk of fatal injury from electric shock Before performing maintenance Disconnect the appliance from the power supply Have the necessary repairs carried out by a qualified specialist with original spare parts 5 1 CLEANING THE FILTER Cleaning interval Required tools material 1 x monthly Dishwashing detergent Alternative Dishwasher Remove the access plate to the condenser Remove the filter from the appliance Clean the filter in the rinsing sink using a household dishwashing detergent Rinse with clear water Let dry Alternative Rinse the filter in the dishwasher Insert the filter Close the access plate 9 2 CLEANING THE CONDENSER RIBS IMPORTANT Clean condensers have a major influence on the service life of the compressor 26 Frozen fry dispenser F3D3S F3D3 F3D3SP F3D3P Status 07 2012 Risk of injury The condenser ribs are sharp Contact may result in cutting injuries Do not touch the condenser ribs Wear gloves if necessary Cleaning interval Required tools material 1 x monthly Brush with soft bristles Alternative Vacuum cleaner Remove the access plate to the condenser Remove the filter from the appliance Free the condenser ribs of dust and dirt using a brush with soft bristles or a vacuum cleaner Insert the filter Close the access plate 5 3 CUSTOMER SERVICE ELECTRIC COMPONENTS n case of malfunction contact technical cus
23. nsideration due to the coolant s high flammability The F3D3 is available in 4 different models F3D3 Single Lane with one dispenser lane using R404A refrigerant F3D3SP Single Lane with one dispenser lane using propane refrigerant F3D3 Dual Lane with two dispenser lanes using R404A refrigerant F3D3P Dual Lane with two dispenser lanes using propane refrigerant ocope of delivery components Non removable components permanently installed in the freezer Bucket with filler doors Removable components in appliance Hopper Single Lane 1 unit Dual Lane 2 units Deflector Single Lane 1 unit Dual Lane 2 units Freezer bottom 1 unit Wire rack 1 unit Removable components in accessories box Upper basket wire rack with basket guides 1 unit Lower basket wire rack 1 unit Lower drip pan 1 unit Crumb tray 1 unit option Accessories optional only for the dual lane models Side basket wire rack Collecting pan for the side basket wire rack Frozen fry dispenser F3D3S FSD3 F3D3SP F3D3P Status 07 2012 15 F3D3S und F8D35P Single Lane Compressor cabinet Access plates to condenser Warning and pro hibitory signs Control panel of the dispenser lane Power switch Hopper with drum Deflector rubber Handles for manually turning the drum Freezer bottom Storage area for unused baskets Upper basket wire rack with basket guide Lower basket wire
24. ormity was tested using the harmonized EN standards EMC EN 55014 1 2007 EN 55014 2 2007 MD EN 60204 1 2006 EN ISO 14121 1 2007 EN ISO 12100 1 2003 A1 2009 EN ISO 12100 2 2003 A1 2009 Responsible for Declaration of Confor mity Mikolaj Liskin Franke Foodservice Systems Poland Sp z 0 0 ul Polnocna 11 81 029 Gdynia Poland Switchboard 48 58 6609 100 Direct phone 48 58 6609 146 Direct fax 48 58 6609 149 Email Mikolaj Liskin Franke com User manual ltem no 19004639 Revision date 06 07 2012 This document reflects the technical status at the time of the revision We reserve the right to make technical changes CONTENT MEL 0 oct ce n tance 4 Ll Symbols Trom the user Manual eseessusasessteebture tne bna uR tesa vba et Evae p OUR EFI br etas 4 L2 iare aao pronto SENE scsessopssa taU VM FRETI IEUPETTPA UR RIDE rA DIES PRIISUMI M SINUS 1 BSI USE a E AAE RC DES AAN ANAMA ERAUR RS ANA S ANAS PSV R ARER d A S MS des Tm Ts 6 MER cine UT e er E AAE A P rre A rE r E 9 L eunt Eorum 9 Za Removine the packagne DOX ucnbpatI eto inntir PEE UMIPI PINE NUDM MUN TNI MEL AU 11 M ES 9 did RII 307 RN IZ A3 Senine up the a WN PERIERE T TOES 12 ZA Changing the door NInge siuvismimsesmimsi nirai nra ni a RAER AEAII NAAA EVNENE Ad 13 2 0 ENO e gt CORPS Cll OU Ee E ET 13 uc E NN 13 3 Appliance GESCIIPtiON cccccccssscccsssccc
25. other Set all components upright to air dry Place the hopper upside down so the water can drain out of it Cleaning the interior and non removable components Wipe off and disinfect the refrigerator and the bucket see Fig 05 with a cloth In particular wipe off and disinfect the front and back of the filler doors and the entire bucket Carefully wipe all parts dry with a sterile fabric Tip The filler doors of the bucket are spring loaded and can be opened by pushing on them carefully All parts of the bucket are more easily accessible for cleaning with the filler doors fully open 3 2 DAILY PROCEDURE FOR STARTING UP SWITCHING ON Assembling the appliance NOTICE Appliance damage Components that are frozen together may damage the appliance Never place wet components into the freezer Frozen fry dispenser F3D3S FSD3 F3D3SP F3D3P Status 07 2012 19 Insert the freezer bottom Slide the deflector into the Insert the hopper Ensure that with the right orientation The hopper with the short side the hub is fully engaged in the slanted surface must face first drum Turn the drum at the Tip down and toward the rear handle if necessary until the If the hub is not fully engaged Press It down hub engages the hopper will not be in the right position and the freezer will not be able to close In this case turn the drum slightly at the handle until the hub fully engages Insert the lower drip pan In
26. prepare a quotation for the customer for the return and disposal of the waste appliance at the time of disposal The customer will be charged for transport and disposal costs special regulations apply when disposing of refrigerant IMPORTANT Releasing refrigerant into the atmosphere is strictly forbidden The refrigerant used is either R404A or R290 The necessary specifications on handling the coolant are given in the manufacturer s data sheet If you would like more information about this product please contact the manufacturer R290 R404a Linde AG Arkema Direction de la Communication Werksgruppe Technische Gase Financiere Seitnerstrasse 70 4 8 cours Michelet La Defense 10 82049 Hollriegelskreuth 92091 Paris La Defense Cedex Germany France Tel 49 0 89 7446 0 Tel 33 0 1 49 00 74 63 Fax 33 0 1 49 00 50 24 Frozen fry dispenser F3D3S FSD3 F3D3SP F3D3P Status 07 2012 33 Locations Germany Franke Foodservice Systems GmbH Jurastrasse 3 79713 Bad S ckingen Germany Phone 49 7761 5533 0 Fax 49 7761 5533 8700 France Franke Foodservice Systems GmbH France Phone 0033 0 626 35 11 58 Fax 0049 0 7761 55 33 93 83 Email thierry krukar franke com Poland Franke Foodservice Systems Poland Sp z o o ul Polnocna 11 81 029 Gdynia Poland Phone 48 58 6609100 Fax 48 58 6609119 Italy Franke Foodservice Systems GmbH Italy Phone 1 0039 345 76 60 050 Phone 2 0039 347
27. r F3D3S F3D3 F3D3SP F3D3P Status 07 2012 Frozen fry dispenser F3D3S FSD3 F3D3SP F3D3P Status 07 2012 Risk of injury when unpacking A tilt indicator is mounted on the shipping box It must show the correct display see Fig 01 Only unpack the appliance if the tilt indicator shows the correct display Do not unpack the appliance if the tilt indicator display is incorrect Contact technical cus tomer service The straps on the shipping box are under tension The wood of the pallet can splinter Keep an adequate distance when cutting the straps Wear gloves and goggles when unpacking The appliance is very heavy top heavy and can easily tip Therefore the pallet is designed so the appliance can only be pushed forward off the pallet with the aid of 2 metal ramps Do not unpack the appliance alone The appliance should be unpacked by two or three people Do not try to push the appliance off the pallet sideways or toward the rear Danger of molds microbes and viruses If the appliance is inadequately cleaned food residues will deposit on interior surfaces especially in the hoppers and on the wire racks Adhere to the cleaning intervals Read the Cleaning chapter Risk of injury The condenser ribs are sharp and can cause cutting injuries Do not touch the condenser ribs while cleaning Wear suitable gloves while cleaning The cooling lines can become very hot and cause burns
28. ress the ON OFF button for 4 seconds until the button LEDs go out The dispenser lane is switched off 2 Press the power switch to disconnect the appliance from the power supply The indicator lamp in the switch goes out 3 lake the hopper out of the appliance 4 Fill the remaining fries from the hopper into a suitable storage container and store them in the freezer room Frozen fry dispenser F3D3S FSD3 F3D3SP F3D3P Status 07 2012 23 Risk of fatal injury from electric shock Before cleaning Disconnect the appliance from the power supply Moisture on the electrical components can lead to a short circuit and to serious or even fatal injury on contact Never clean the appliance with a direct water jet a sponge or a high pressure water Jet 4 1 DEFROSTING The appliance must be disconnected from the power supply No products must be located inside the appliance 1 Take all removable components except for the bottom drip pan out of the appliance The drip pan will catch the dripping melt water 2 Remove the deflector from the hopper s NOTICE Damage The freezer should only be defrosted passively Switch off the appliance at the power switch and leave the door open Never scratch the ice layers off the freezer walls to accelerate the defrosting process 3 Let the appliance defrost with the door open 4 Remove the collecting pan of the side basket wire rack if present 24 Frozen fry dispenser F3D3S F3D3
29. ror The screen displays an error message LCD screen Displays the current operating temperature of the freezer Displays error messages and pos A A 4 sible causes Displays the appliance setup and diagnosis programs with possible measures or decision options ON OFF button For switching on the dispenser lane Press for 4 seconds until both LEDs light up ACTION 3 button Performs the actions that are dis played on the screen OK confirm Reset 2 LEDs ACTION 1 button Performs the ac flash tions that are displayed on the screen Inc increase ACTION 2 button Performs the ac tions displayed on the screen Dec 7 decrease 3 1 BEFORE STARTING UP FOR THE FIRST TIME Before starting up for the first time all components of the appliance must be cleaned Cleaning removable components The removable components are located firstly in the appliance itself and secondly in the ac cessories box see scope of delivery 18 Frozen fry dispenser F3D3S F3D3 F3D3SP F3D3P Status 07 2012 Fig 05 Bucket with filler doors NOTICE Appliance damage Rinsing with water that is too hot can deform the hopper s Clean the hopper s with lukewarm water only Components that are frozen together may damage the appliance Never place wet components into the freezer Carefully dry the components after cleaning Wash and disinfect all components in the rinsing sink one after the
30. sert the lower basket wire Place the upper basket wire rack rack onto the cross supports Roll the appliance into posi tion and block the brakes of the front castors Insert the crumb tray Insert the wire rack in the freezer above the hopper s Only for dual lane models Mount the side basket wire rack if present Position the collecting pan under the basket wire rack 20 Frozen fry dispenser F3D3S F3D3 F3D3SP F3D3P Status 07 2012 Switching on letting cool to the operating temperature Close the freezer Switch the cooling system on at the power switch The indicator lamp in the switch lights up The cooling process begins The current temperature is shown on the display as the freezer cools see Fig 06 After approx 3 hours the appliance will have reached the required operating temperature 18 to 23 C Depending on the ambient conditions Fig 06 Display with temperature room temperature and humidity cooling may take longer actual value 3 3 FILLING WITH FRIES IMPORTANT The products should not be filled until the required operating temperature is reached NOTICE Ice on the freezer walls prevents the appliance from reaching its operating temperature Remove the wire rack Do not leave the freezer Check the hopper Remove door open longer than is any product remnants necessary for filling Defrost the appliance daily see the Cleaning chap ter Repeat
31. spenser F3D3S F3D3 F3D3SP F3D3P Status 07 2012 2 4 CHANGING THE DOOR HINGE The freezer should open on the side from which the fries are easier to fill The appliance is delivered with a right hinged door by default Depending on the situation the hinges may need to be changed Instructions on changing the hinges can be found in the Service Manual 2 6 ELECTRICAL CONNECTION Locally applicable electrical installation and safety regulations must be observed The connection to the electrical supply grid must conform to the relevant standards Before establishing the power connection check that the voltage and frequency given on the rating plate match the values of the electrical supply grid Move the appliance into position and lock the brakes of the two front castors F3D3P FS3DSSP Insert the connector into a 230 V 50 Hz power socket The power cable provided is 3 m long F3D3 F3D3S Insert the connector into a 230 V 50 amp 60 Hz or 120 V 60 Hz power socket The power cable provided is 3 m long IMPORTANT The appliance must be integrated in a potential equalization system The corresponding clamp is marked with a label This connection must comply with regulations and must be tested for effectiveness 2 5 FINAL STEPS Pulling off the protective films Carefully pull the protective film off the stainless steel surfaces Remove any glue residues with a suitable solvent Frozen fry dispenser F3D3S FSD3 F3
32. tomer service Please provide the item number and type This information is located on the rating plate Frozen fry dispenser F3D3S FSD3 F3D3SP F3D3P Status 07 2012 27 5 4 CUSTOMER SERVICE COOLING SYSTEM Danger of fire The cooling circuit is filled with R290 propane Propane is highly flammable Work analysis repair maintenance on the cooling system is only allowed under certain conditions Never repair the cooling system yourself If you experience problems contact the technical customer service The appliance may only be repaired by a refrigeration technician under certain conditions Certain requirements apply to work analysis repair maintenance on cooling systems that must be strictly observed If these requirements are not fulfilled then this will result in the expiry of the guarantee cover and the manufacturer accepts no liability Work on cooling systems must never be carried out in rooms at the restaurant he appliance may be repaired in a suitable workshop It is important to ensure that there is sufficient ventilation he appliance may only be kept outside in the open air for the duration of the work on the cooling system he work may only be carried out by a qualified certified specialist company The relevant local standards and laws for this qualification are valid only F3DSSP F3D3P 28 Frozen fry dispenser F3D3S F3D3 F3D3SP F3D3P Status 07 2012 MALFUNCTIONS TROUBLESHOOTIN
Download Pdf Manuals
Related Search