obd ii hand held quikcode user`s manual
Contents
1. To avoid possible personal injury and damage to the vehicle please refer to the appropriate vehicle manufacturer s service procedures and safety instructions Objects can be propelled by moving engine parts These objects and high pressure fluids and liquids can cause serious injury ALWAYS wear an ANSI approved eye protection Ensure all sparks lighted cigarettes open flames or any other device capable of producing a high temperature are not utilized near automotive batteries Automotive batteries contain sulfuric acid and produce explosive gases Ensure a safe distance from all moving engine components during servicing Test equipment clothing and parts of your body can be seriously damaged or injured An operating engine produces carbon monoxide which is an odorless colorless poisonous gas that can lead to serious injury or death ALWAYS service an operating engine in a well ventilated area Fuel systems are typically under high pressure Ensure the area is well ventilated and free of all sparks or other ignition sources to avoid the possibility of fire Ensure the parking brake is engaged the vehicle s drive wheels are blocked and the gear selector is in neutral for manual transmissions and in park for automatics Never set tools on a vehicle s battery You many short the terminals together causing harm to yourself the tools or the battery NEVER attempt to operate this software and drive the vehicle at the same2. COM port the unit is connected to is selected in the software Select Device Select COM Por in the software menubar e Check the display on the QuikCode if it is trying to connect to a vehicle cycle the power to the unit 6 Click the Update Device Firmware button In Section A of the Select Tab click the Select Local File button to load a firmware file that is saved on the PC to the QuikCode unit The file extension for a QuikCode firmware file is qci Or click the Retrieve Latest File from EASE Website button to load the latest file from the EASE website The PC must be connected to the internet to retrieve the file After a firmware file is selected click the Update button to continue 8 When prompted cycle the power to the QuikCode unit After which the software will automatically start uploading the firmware file to the unit 9 When complete on the bottom of the Upload Tab a message will be displayed saying that the firmware has been successfully uploaded Click the Exit button to close the screen 10 Cycle the power to the QuikCode unit 11 Verify on the main screen that the Firmware Version displayed is the correct version TEASE Diagnostics Device Utility Device Firmware Update x Device Firmware Update x File Device About Select ReBoot UpLoad CPLD Flash Select ReBoot UpLoad CPLD Flash Type QuikCode Interface Status Ready A Select Firmware File Uploading uC Flash Descri
3. Displays MIL Status ie splays conunubus and Non Conunuous e Displays Continuous and Non Continuous e Monitor Test Results I M Status Monitor Test Results I M Status Cleans D TUSLI TERZA TAMS IM Monori e Clears DTCs Freeze Frame IM Monitors Features e Enhanced DTC Requests SAE J 2190 s Enhanced DTC Regueste SAE 12190 e Performs Continuous DTC Scan s Peras DE DTC Scan TO e Emissions Test Mode GM Curent and History Enhanced DTCs e GM Current and History Enhanced DTCs gt EO DL Diesel Dis e Ford 7 3L Diesel DTCs R DIES e Ford ABS DTCs e Unitis updateable using PC e Chrysler SCI Hex DTCs e Displays VIN Data for 2002 and newer vehicles y For your vehicle to be OBD II compliant it must have a 16 pin DLC under the dash and the vehicle Emission Control Information label must state that the vehicle is OBD II compliant This label is located on the inside of the hood on most vehicles An example of this label is shown below Note the last line of the label states that the vehicle is OBD Il certified Vehicle Emission Control Information This vehicle is equipped with electronic control systems Engine idle speed idle mixture and ignition timing are not adjustable See Powertrain Control Emissions Diagnosis Manual for additional information DLC Data Link Connector a 16 position connector located under the driver side dash of most vehicles This vehicle conforms to U S EPA and California regulations applicab
4. time ALWAYS have another person to use the software while the vehicle is being driven Do not leave your vehicle unattended while running tests II LIMITED WARRANTY To the original purchaser only EASE warrants the supplied hardware products to be free from defects in materials and workmanship under normal use for a period of one 1 year from the date of purchase as evidenced by a copy of the sales receipt EASE makes no other express warranty on the hardware products The purchaser s sole remedy in the event of a breach of warranty is expressly limited to repair or replacement of the defective hardware or if replacement is not possible a refund of the purchase price Repair parts and replacement hardware products will be provided on an exchange basis and will be either reconditioned or new All replaced parts become property of EASE This limited warranty does not cover damage to the products resulting from misuse accident disaster abuse negligence improper maintenance or modification and or repair of the hardware product other than by EASE EASE does not warrant that the operation of the hardware software will be uninterrupted or error free Further EASE does not warrant or guarantee the use of or the results of the use of the hardware software in terms of correctness accuracy reliability currentness or otherwise you rely on the hardware software and results solely at your own risk The licensee s sole and exclusive remedy for fai
5. use are made or implied by EASE Simulation Inc We reserve the right to revise this document or make any changes in the specification of the product described therein at any time without notice and without obligation to notify any person of such revision or change TRADEMARK ACKNOWLEDGMENTS EASE and QuikCode OBD ll are trademarks of EASE Simulation Inc GM is a registered trademark of General Motors Corporation All other trademarks property of their respective owners EASE Hand Held QuikCode User s Manual Copyright C 1997 2005 EASE Simulation Inc All rights reserved Printed in the United States of America TABLE OF CONTENTS I SAFETY PRECAUTIONS 2 ll LIMITED WARRANTY 3 lll TECHNICAL SUPPORT 3 IV VEHICLE REQUIREMENTS 4 V AUTOMOBILE ON BOARD COMPUTERS AND DIAGNOSTIC TROUBLE CODES _ 5 OBD II 5 Automobile On board Computers 5 Malfunction Indicator Lamp MIL 5 Freeze Frame Data 5 Diagnostic Trouble Codes or DTCs 6 OBD II Inspection and Maintenance I M Readiness Monitors 7 VI SETUP PROCEDURES 8 The EASE OBD II Hand Held QuikCode Unit 8 Locating Your Vehicle s Diagnostic Connector 8 Connecting QuikCode to Your Vehicle s Diagnostic Connector 9 Updating the QuikCode s Firmware QC2 HH CAN only 9 Flow Charts for the OBD Il Hand Held QuikCode s Display Menu 11 CAN Enabled QuikCode QC2 HH CAN Flow Charts 11 Original QuikCode QC2 HH Flow Charts 17 l SAFETY PRECAUTIONS BEFORE WORKING ON ANY VEHICLE PLEASE READ THIS
6. COMPL TEST COMPLETED NOT SUPPORTED TEST NOT COMPL NOT SUPPORTED SCROLL NO CATALYST MONITOR TEST COMPLETED REVIEW I M SCAN TEST NOT COMPL GOTO NOT SUPPORTED HEATED CAT MON TEST COMPLETED YES TEST NOT COMPL MIL LIGHT ON NOT SUPPORTED ac ACTIVE PXXXX EVAP SYS MON TEST COMPLETED NO TEST NOT COMPL NOT SUPPORTED SEC AIR SYS MON TEST COMPLETED Is this an EMISSION SCAN Were Stored DTCs found SELECT YES TEST NOT COMPL NOT SUPPORTED SCAN COMPLETE Original GuikCode QC2 HH Flow Charts The following flowcharts are for the original GuikCode QUIKCODE VERSION 3 4 Interface Active EMISSIONS SCAN START SCROLL NO GOTO POWERTRAIN SCAN MIL LIGHT ON MIL LIGHT OFF SCROLL NO m ao IM SCAN SCROLL NO CONT DTC SCAN GOTO SELECT YES GOTO SCROLL NO Were Stored DTCs found NO STORED CODES GOTO 2 YES YES PXXXX Active Were Pending DTCs found PXXXX Pending SCROLL NO Goto NO Q GOTO Q NO PENDING CODES SELECT YES GOTO CLEAR IM CODES gt SINGLE RESCAN ENH PWR GM SCAN GOTO NA GOTO SELECT YES GOTO ENH HIS GM SCAN IS VEHICLE YES GOTO ISO 9141 SELECT YES QUIKCODE END GOTO RESTART SCROLL NO A C SYS REF MON TEST COMPLETED IM SCAN TEST NOT COMPL NOT SUPPORTED MISFIRE MONITOR TEST COMPLETED SINGEN SENIMON TEST NO
7. E MAY DAMAGE THE EASE OBD li HAND HELD QUIKCODE BASIC TOOL This section includes the following The EASE OBD II Hand Held QuikCode Unit Locating Your Vehicle s Diagnostic Connector Connecting the EASE OBD II Hand Held QuikCode To Your Vehicle s Diagnostic Connector Flow Charts for the OBD II Hand Held QuikCode Basic Tool s Display Menu Updating the Unit s Firmware The EASE OBD II Hand Held QuikCode Unit The OBD II Hand Held QuikCode Unit components and functions are listed aa below Qu Code DISPLAY Data selection menus and vehicle data is displayed here TWO BUTTONS The buttons are used to select and scroll through the displayed menu VEHICLE INTERFACE CABLE Attach this cable to the DB25 connector located on top of the QuikCode unit This cable is used to connect the QuikCode OBD Il unit to your vehicle s diagnostic connector so that it may scan the vehicle NOTE The vehicle s diagnostic connector powers the QuikCode Tool therefore no power cords or batteries are required SELECT SCROLL YES NO Locating Your Vehicle s Diagnostic Connector EASE In order for the QuikCode OBD II Unit to work it must be connected to your vehicle To do this you must first locate your vehicle s diagnostic connector See Figure 1 below This connector is referred to as the Data Link Connector DLC Figure 1 DLC Data Link Connector a 16 position connector located under the driver side dash of most vehicles O
8. NDING CODES SELECT YES GOTO CLEAR IM CODES SCROLL NO SELECT YES GOTO SINGLE RESCAN SCROLL NO ENH PWR GM SCAN GOTO GOTO SELECT YES GOTO Y m CD ENH HIS GM SCAN SCROLL NO GET 2002 VIN SCROLL NO GOTO Z j SELECT YES IS VIN YES VIN 123456789AB SUPPORTED 12 17 123456 Q O O O SELECT YES QUIKCODE END GOTO RESTART SCROLL NO GOTO 12 Are There Any New Active DTCs PXXXX ACTIVE SCROLL NO REVIEW DTC SCAN SCROLL NO SCANNING Hold both YES and NO Are There Any Active DTCs SELECT YES SCROLL NO SELECT YES E E ENH HIS GM SCAN Were DTCs found P1XXX ACTIVE CLEAR ENH CODES GOTO SINGLE RESCAN GOTO REVIEW DTC SCAN GOTO NO ACTIVE CODES SCROLL NO SCROLL NO GOTO GOTO Were DTCs found NO NO ACTIVE CODES IS THE ENHANCED SCAN FINISHED CLEAR ENH CODES ARE YOU SURE CODES CLEARED SCROLL NO A C SYS REF MON TEST COMPLETED IM SCAN TEST NOT COMPL NOT SUPPORTED MISFIRE MONITOR TEST COMPLETED OXYGEN SEN MON TEST NOT COMPL TEST COMPLETED NOT SUPPORTED TEST NOT COMPL NOT SUPPORTED SCROLL NO SCROLL NO FUEL SYSTEM MON TEST COMPLETED MEMES OLSEN TEST NOT COMPL TEST COMPLETED NOT SUPPORTED TEST NOT COMPL NOT SUPPORTED COMPREH COMP EGR SYSTEM MON TEST COMPLETED TEST NOT
9. NHANCED SCAN FINISHED NO NO ACTIVE CODES SCROLL NO GOTO CLEAR ENH CODES SCROLL NO SELECT YES GOTO GOTO ARE YOU SURE CODES CLEARED SCROLL NO 22 GOTO TURN VEHICLE ON IN YES SCI XX ACTIVE SUPPORTED SCROLL NO NO SELECT YES ki REVIEW DTC SCAN SCROLL NO SCAN COMPLETE 9 gt a gt soROLLNO gt SGROLL NO CODES Cleared GOTO SELECT YES SINGLE RESCAN w GOTO GOTO N 3
10. OBD II HAND HELD OUIKCODE USER S MANUAL Rev 111405 THANK YOU THANK YOU for the purchase of the QuikCode OBD II and welcome to the professional product line of EASE Diagnostics This QuikCode OBD II is designed to work with all OBD II Compliant vehicles COPYRIGHT This document and accompanying software are copyrighted and all rights are reserved by EASE Simulation Inc Copying of this document or software for other than backup purposes is illegal No part of this document and accompanying software may be reproduced translated stored in a retrieval system or transmitted in any form by any means electronic mechanical photoreproductive recording or otherwise without the expressed prior written permission of EASE Simulation Inc All products and trade names described within are mentioned for identification purposes only No affiliation with or endorsement of the manufacturer is made or implied Product names appearing in this manual are registered trademarks of their respective companies Information furnished by EASE Simulation Inc is believed to be accurate and reliable However EASE Simulation Inc assumes no responsibility for the use of such information or for any infringements of patents or other rights of third parties that may result from its use No license is granted by implication or otherwise under any patent rights of EASE Simulation Inc No representation or warranties regarding the fitness of this document for any
11. T COMPL TEST COMPLETED NOT SUPPORTED TEST NOT COMPL NOT SUPPORTED SCROLL NO SCROLL NO FUEL SYSTEM MON TEST COMPLETED ADAN TEST NOT COMPL TEST COMPLETED NOT SUPPORTED TEST NOT COMPL NOT SUPPORTED COMPREH COMP EGR SYSTEM MON TEST COMPLETED TEST NOT COMPL TEST COMPLETED NOT SUPPORTED TEST NOT COMPL NOT SUPPORTED SCROLL NO SCROLL NO CATALYST MONITOR TEST COMPLETED REVIEW I M SCAN e TEST NOT COMPL GOTO NOT SUPPORTED NO HEATED CAT MON GOTO Is this an EMISSION SCAN TEST COMPLETED YES TEST NOT COMPL NOT SUPPORTED Er OEE YES SCROLL NO EVAP SYS MON TEST COMPLETED NO NOT SUPPORTED NO STORED CODES REVIEW DTC SEC AIR SYS MON TEST COMPLETED TEST NOT COMPL Were Stored DTCs found ACTIVE PXXXX SCAN COMPLETE NOT SUPPORTED Are There Any New Active DTCs PXXXX ACTIVE SCROLL NO REVIEW DTC SCAN SCROLL NO SCANNING Hold both YES and NO Are There Any Active DTCs E ARE YOU SURE CODES CLEARED GOTO GOTO 20 SCROLL NO ENH HIS GM SCAN Were DTCs found P1XXX ACTIVE CLEAR ENH CODES GOTO SCROLL NO SELECT YES GOTO NO ACTIVE CODES SINGLE RESCAN SCROLL NO SELECT YES u CODES CLEARED ARE YOU SURE SCROLL NO SCROLL NO GOTO GOTO 21 ENHANCED SCAN Were DTCs found XXXXX ACTIVE IS THE E
12. and is either a red or yellow labeled lamp The MIL is normally off and will illuminate if a system or component either fails or deteriorates to the point where the vehicle emissions could rise 1 5 times above the FTP set emissions level Freeze Frame Data When the first emissions related powertrain DTC becomes stored the PCM will capture save a block of current engine parameters This list of parameters is called Freeze Frame Data and consists of a fixed list of parameters For vehicles which do not support all parameters only the applicable ones are stored The first parameter in the list is always the DTC that caused the Freeze Frame When DTCs are cleared the Freeze Frame Data is cleared from the vehicle s PCM Diagnostic Trouble Codes or DTCs In the past malfunction code numbers varied between manufacturers years makes and models OBD II requires that all vehicle manufacturers use a common Diagnostic Trouble Code or DTC numbering System There is a generic DTC listing that all manufacturers must use Since the generic listing was not specific enough most manufacturers came up with their own DTC listing which are called manufacturer specific codes Both generic and manufacturer specific codes consist of 5 digits interpreted as follows Second Digit First Digit 0 1 2 3 Manufacturer Specific P Powertrian ISO SAE Manufacturer Specific ISO SAE ISO SAE Required B Body ISO SAE Manufacturer Specific Manu
13. computers control engines transmissions brakes traction and many other components These computers have several names and acronyms depending upon the manufacturer and components they control The most common name is PCM or Powertrain Control Modules Other examples are Body Control Modules BCM Transmission Control Modules TCM Electronic Brake Control Module EBCM and Air Conditioning Control Module ACM A variety of sensors such as the oxygen sensor throttle position sensor and manifold air temperature sensor provide information to the on board computer regarding the vehicle s engine operating conditions Air Conditioning systems vehicle air bags and anti lock brake systems also report to on board computers On board computers have a built in self testing system called self diagnosis which means the on board computer will monitor many or all of the vehicle s sensors and controlled devices for proper operation A diagnostic trouble code or DTC is detected and set when one of the monitored devices is not functioning properly This malfunction is stored into the on board computer s memory as a DTC number that is related to a specific sensor or other problem The computer can later be accessed using the EASE software or other scan tools and code reading devices to obtain the codes stored in the on board computer memory Malfunction Indicator Lamp MIL The Malfunction Indicator Lamp MIL is located in the instrument panel on the dashboard
14. echsupport obd2 com IV VEHICLE REQUIREMENTS EASE offers two versions of the Hand Held QuikCode The original OBD II Hand Held QuikCode QC2 HH is designed to work with OBD II compliant vehicles without CAN The new OBD II Hand Held CAN Enabled QuikCode QC2 HH CAN works with OBD Il compliant vehicles including vehicles with the new CAN communications interface OBD II CAN Enabled QuikCode Original OBD II Hand Held QuikCode Part Number QC2 HH CAN Part Number QC2 HH e 1996 and newer OBD Il Compliant Vehicle Includes Domestic Asian and European e 1996 and newer OBD II Compliant Vehicle without Vehicle Passenger Vehicles CAN Includes Domestic Asian and European Requirements Some 1994 and 1995 vehicles are OBD Il Passenger Vehicles Compliant e Some 1994 and 1995 vehicles are OBD II e Vehicles with the CAN controller area network Compliant communications interface e 1996 and newer Domestic Asian and European SIA OBD Il compliant vehicles including the new 2 ns a eee ne e Supported CAN vehicles Protocols e Supports OBD Il interfaces SAE 1850 VPW oa oe TEONE R ASC nani 14230 KWP2000 Chrysler SCI A 14230 KWP 2000 ISO 15765 SAE J 2284 CAN Displays gt plored DEC number e Displays Generic Stored DTC numbers x Displays Generic Pending a numbers e Displays Generic Pending DTC numbers Displays Manufacturer Specific DTC numbers e Displays Manufacturer Specific DTC numbers Displays MIL Status e
15. facturer Specific Reserved C Chassis ISO SAE Manufacturer Specific Manufacturer Specific Reserved nn or data link ISO SAE Manufacturer Specific Manufacturer Specific Reserved The third digit represents the specific vehicle system that has the fault Listed below are the number identifiers for the powertrain system _ Fuel and Air Metering Fuel and Air Metering Injector Circuit Malfunctions Only Ignition System or Misfire Auxiliary Emission Control Vehicle Speed Control and Idle Control System Computer and Auxiliary Outputs Transmission Transmission Transmission gt o o IN jo A ON Hybrid Fuel and Air Metering and Auxiliary Emission Controls The last two digits indicate the specific fault index The following is an example of a diagnostic trouble code P0301 Cylinder 1 Misfire Detected Whereas P Powertrain 0 ISO SAE 3 lgnition System or Misfire On OBD II vehicles there are two different types of DTCs Stored and Pending For a DTC to become Stored certain malfunction conditions must occur The condition s required to Store a code are different for every DTC and vary by vehicle manufacturer In order for some DTCs to become Stored a malfunction condition has to happen more than once If the malfunction conditions are required to occur more than once the potential malfunction is called a Pending DTC The DTC remains Pending until the malfunction condition
16. le to 1998 model year new LEV passenger cars certified for sale in California HSC 39037 05 Low Emission Motor Vehicle OBD Il Certified OBD II Certified Vehicle Emission Control Information Label located inside the hood of most vehicles Use it to identify whether or not the vehicle is OBD II certified V AUTOMOBILE ON BOARD COMPUTERS AND DIAGNOSTIC TROUBLE CODES The following section provides information on OBD II Automobile on board computers The Malfunction Indicator Lamp MIL Freeze Frame Data Diagnostic Trouble Codes DTC Inspection and Maintenance 1 M Readiness Monitors O O1 BB D OBD II Federal law required all vehicle manufacturers to meet On Board Diagnostics Second Generation or OBD II standards by 1996 In order to meet this standard the automobile s on board computer must monitor and perform diagnostic tests on vehicle emissions to ensure that the vehicle is operating at an acceptable legal emission level The maximum allowable emission level is set by the Federal Test Procedure FTP All 1996 and newer passenger vehicles are OBD II compliant All OBD II vehicles have the same 16 pin diagnostic connector or DLC This eliminates the need to have a manufacturer specific connector to connect to your vehicle Some 1994 and 1995 vehicles have this connector however this does not mean that the vehicle is OBD Il compliant Automobile On board Computers Automobile on board
17. lure of the hardware software to materially conform to the specifications defined in the pertinent documentation is for the licensee to return the hardware software to EASE and notify EASE in writing of such non conformity within thirty 30 days of delivery to the licensee EASE s sole obligation shall be at EASE s option within a reasonable time after EASE receives notice of non conformity to either provide the licensee with hardware software which conforms to the express warranty above or refund to the licensee the licensee fee paid therefore In the event of a refund this agreement shall be considered terminated and the licensee if they have any copies of the hardware software or related materials shall promptly deliver to EASE and or destroy all such copies including that in memory or data storage apparatus and warrant in writing to EASE within thirty 30 days of termination that the licensed hardware software related materials and all copies thereof have been either returned and or destroyed Limitation of Liability Neither EASE nor its authorized dealer s shall be liable for any defect indirect incidental special or consequential damages whether in an action in contract or tort including negligence and strict liability such as but not limited to loss of anticipated profits or benefits resulting from the use of this software and or hardware product or any breach of any warranty even if EASE or its authorized dealer s has been advi
18. n most vehicles the DLC is located under the driver s side dashboard in full view See Figure 2 In some vehicles it may be recessed behind a panel Remove this panel for access to the connector Other vehicles have a cap labeled Diagnostic Connector over the connector Remove this cap to connect the QuikCode OBD II Replace this cover when you are finished If you are unable to find the DLC consult the vehicle s service manual for the exact location Figure 2 Location of the Data Link Connector DLC 8 Connecting QuikCode to Your Vehicle s Diagnostic Connector After you have located your diagnostic connector you are ready to connect the EASE OBD II Hand Held QuikCode Tool to your vehicle by following the steps below 1 SAFETY FIRST Review Section Safety Precautions 2 Turn the vehicle s Ignition OFF 3 Connect the EASE OBD II Hand Held QuikCode s vehicle interface cable to the vehicle s diagnostic connector 4 Turn your vehicle s ignition switch to the ON position IMPORTANT Chrysler vehicles may have two key on positions For proper operation make sure the vehicle s ignition is in the second key on position ot Qui Code 5 Scroll through the menu on the display to scan and view the vehicle s stored and pending DTCs Inspection and Maintenance Monitors and MIL Status NOTE The vehicle s diagnostic connector powers the QuikCode unit OBD Il therefore no power cords or batteries are requi
19. occurs the required number of times to make the code Stored If the malfunction condition does not occur again after a set time the Pending DTC will be cleared OBD II Inspection and Maintenance I M Readiness Monitors A monitor is a piece of software in one of the vehicle s on board computers that has the job of monitoring a specific piece of the engine There are two types of monitors continuous and non continuous A continuous monitor runs continuously during vehicle operation A non continuous monitor requires enabling criteria to make it run Some examples of enabling criteria are vehicle acceleration deceleration to a certain speed engine temperature and driving the vehicle at a certain speed for a period of time For OBD II vehicles there is a fixed list of 11 monitors 3 continuous and 8 non continuous The 11 monitors are not applicable for all vehicles The Inspection amp Maintenance screen of the software lists the availability and status of your vehicles monitors In order to pass an emission inspection all of the supported monitors must be completed The Continuous Monitors are e Misfire e Fuel System e Components The Non Continuous Monitors are e Catalyst e Secondary Air System e Oxygen Sensor e Heated Catalyst e A C System e Oxygen Sensor Heater e Evaporative System e EGR System VI SETUP PROCEDURES NOTICE THIS PRODUCT IS DESIGNED TO OPERATE AT A VEHICLE S NORMAL BATTERY VOLTAGE 11 15 VOLTS DC ANY OTHER VOLTAG
20. ption HHOC CAN Select Local File QCI4_04 qci a Retrieve Latest File from Firmware Version QCI4_05 Device Version 4 4 1 EASE Website Device Serial No 0200001053 Selected File The EASE Device Firmware has B Click Update to upload the been successfully upgraded Click selected firmware file to the EASE Exit to close 8 Edit Device Parameters Device v Exit v Update Cancel Flow Charts for the OBD Il Hand Held GuikCode s Display Menu You must use the SELECT YES and SCROLL NO buttons on the QuikCode tool to scan the vehicle and view the results The following flow charts list the steps to follow CAN Enabled QuikCode QC2 HH CAN Flow Charts The flow charts in this section are for the CAN ENABLED QuikCode QUIKCODE CAN EASE DIAGNOSTICS VERSION 1 0 EASE DIAGNOSTICS INTERFACE TYPE VPW PVW ISO 9141 KVP SLOW KVP FAST CAN Q O O Interface Active TURN IGNITION ON Z O Z O U gt 4 gt YES SELECT YES EMISSIONS SCAN START ENGINE SCROLL NO GOTO POWERTRAIN SCAN MIL LIGHT ON MIL LIGHT OFF Che SCROLL NO SELECT YES GOTO IM SCAN SCROLL NO SELECTYES GOTO CONT DTC SCAN SCROLL NO SCANNING Were Stored DTCs found YES STORED CODE PXXXX NO STORED CODES GOTO SCROLL NO F YES GOTO PENDING CODE PXXXX GoTo NO gt GOTO o Were Pending DTCs found NO PE
21. red SELECT SCROLL YES NO EASE Updating the QuikCode s Firmware QC2 HH CAN only The firmware onboard the CAN Enabled QuikCode can be updated by the user with a PC when updates are made available from EASE Firmware Update Requirements e Desktop or Laptop PC with serial port e EASE Device Utility Software e Serial interface cable EASE Part CABLE DB9 6 15 or 25 e When updating the firmware the unit must be powered by a vehicle or an EASE 12 VDC 0 5A power transformer EASE Part TR 12VDC 0 5A To update the firmware follow the instructions below 1 Install the EASE Device Utility Software Insert the EASE Device Utility CD into the PC s CD drive The setup program will start automatically If it does not run X Setup exe where X is the letter that represents your CD drive Follow the on screen instructions to install the software on the PC 2 Start the EASE Device Utility Software 3 Connect a serial interface cable to the COM port on a PC and the DB9 connector on the end of the QuikCode unit 4 Power the unit using a vehicle or an EASE 12 VDC 0 5A power transformer Plug the transformer into the port next to the DB9 connector WARNING Using a power transformer that is not 12 VDC 0 5A could damage the unit 9 5 Ifthe QuikCode unit is connected and powered properly the type on the main screen should read QuikCode Interface If it does not e Check your cable connections e Check that the
22. sed of the possibilities of such damages In no event will EASE or its authorized dealer s liability exceed the price paid for the product Note Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusions or limitations may not apply to you The information presented in this manual is believed to be accurate Responsibility for errors omission of information or consequences resulting from the use of this information cannot be assumed by EASE EASE retains all rights to make changes to specifications at any time without notice How to reach EASE Customer Service is available from 9 00 am to 5 00 PM Eastern Standard Time Please have your sales order or invoice number available when you call By Telephone 570 465 9060 By Fax 570 465 9061 By Mail EASE Diagnostics State Route 492 Box 3011 New Milford PA 18834 USA By e mail info obd2 com Our website is located at www obd2 com II TECHNICAL SUPPORT If you have questions about the use of this product first check the relevant portion of the User s Manual the EASE Software Help System or refer to the EASE website If you cannot find the answer in these places call our Technical support line at 570 465 9062 ext 252 This support line is answered Monday through Friday from 9 00 am to 5 30 PM Eastern Standard Time At other times please leave a message and the call will be returned Also you can e mail your questions or comments to t
Download Pdf Manuals
Related Search