INSTALLATION INSTRUCTIONS
Contents
1. Canopy Screwcollar loop Ring Close the top link of chain Hang the fixture on the chain at the desired height Remove excess chain Close the bottom link of chain Unscrew the ring from the screwcollar loop Let the ring and canopy slide down the chain to the top of the fixture Thread the lead wires and ground wire first through the ring and then the canopy Thread the wires up through alternating links of the chain to the outlet box Measure 6 of lead wire beyond the end of the chain Cut off excess wire Strip the insulation off the ends of the leads exposing approx 1 2 of wire Twist the strands of wire together Push the leads and ground wire up through the screwcollar loop and nipple and into the outlet box Fasten the bare ground wire to the green or bare copper wire in the outlet box or the green screw on the crossbar NEVER FASTEN THE GROUND WIRE TO THE BLACK OR HOT WIRE FAILURE TO FOLLOW THIS INSTRUCTION COULD RESULT IN SERIOUS INJURY OR DEATH Fasten the fixture lead with the ridge s to the white wire in the outlet box Fasten the wires together with an approved fastener wire nut Sterting about 1 below the fastener tightly wrap the connetion with electrical tape so that the tape seals the end of the fastener Make sure that there is no exposed wire or strands that could cause a dangerous short circuit oe tape p N approved fastener wire nut Chain 8 Co2. In regular circumstances the BLACK wire will be the Hot lead and the WHITE wire will be the Neutral or Common lead A GREEN or BARE COPPER wire is the Ground In older buildings it is always good practice to reconfirm the polarity of the wiring 3 This fixture is designed to be mounted on a correctly installed standard round or octagon box or a through wiring box with a plaster frame FIXTURE PREPARATION Outlet box parts are found Ground Screw 2 FIXTURE INSTALLATION Attach the crossbar to the outlet box The green screw should face the floor s N Sa D Remove the threaded ring from the screwcollar loop Open end links of chain and attach the chain to the screwcollar loop e The box must be securly mounted to the structure of the building Remove the fixture parts shades and parts bag s from the carton Before discarding the carton double check to make certain that all i E Ceiling Assemble the center part final and loop to the fixture body Attach the chain to Nipple Crossbar Hex Nut the loop Fully thread the loop onto the nipple Thread the hex nut onto the nipple and the nipple into the crossbar mm Place the canopy over the screwcollar loop and against the ceiling Adjust 7 the nipple so that 1 4 of threads on the screwcollar loop extend beyond the canopy Tighten the hex nut against the crossbar ll F te J WA cA E Nai NI II
3. GENERAL 1 To insure the success this fixture installation the following instructions and diagram s should be read and understood 8716 INSTALLATION INSTRUCTIONS as a gt CHTING ISS All electrical connections must be made in accordance with the National Electric Code and local codes and ordinances If you are uncertain of the methods of installing electrical wiring and lighting fixtures secure the services of a qualified licenced electrician 2 TOOLS NEEDED Chain pliers flat blade screwdriver adjustable wrench or slip joint pliers wire cutter stripper electrical current tester stepladder and electrical tape NOTE The important safeguards and instructions outlined on this sheet cannot cover all possible conditions and situations that may occur It must be understood that common sense caution and care are factors that cannot be built into any product Caution and care must be supplied by the person s installing operating and caring for this lighting fixture INSTALLATION PREPARATION 1 TURN OFF THE ENTIRE ELECTRICAL CIRCUIT TO WHICH THE LIGHTING FIXTURE IS TO BE ATTACHED Move the appropriate circuit breaker to the off position or completely remove the fuse controlling the circuit 2 If an existing fixture is being replaced remove it and note to which of the wires in the outlet box the fixture was attached DO NOT SEPARATE ANY OTHER WIRES THAT MAY BE IN THE BOX DO NOT DAMAGE THE INSULATION OF OLDER WIRING
4. l arame cortador stripper testador de corrente el trica escada e fita isolante Nota As salvaguardas importantes e instru es descritas Esta folha n o se destinam a cobrir todas as condi es poss veis e situa es que pode ocorrer Deve ser entendido que o senso comum cuidado e cuidados s o fatores que n o podem ser compilados em qualquer produto Cautela e cuidados devem ser fornecido pela pessoa ou pessoas a instala o opera o e manuten o deste aparelho de ilumina o 1 DESLIGUE O CIRCUITO ELECTRICO TODO PARA QUE O APARELHO DE ILUMINA O DEVE SER ANEXADO Mover o circuito adequado separador para o fora de posi o ou remover completamente o fus vel controlando o circuito 2 Se um dispositivo el trico existente est sendo substitu do remova oe _ Observe que os fios na caixa de sa da do dispositivo el trico foi anexado N O SEPARAR QUALQUER OUTRO FIOS QUE PODEM SER EM CAIXA NAO DANIFIQUE O ISOLAMENTO DE FIACAO MAIS VELHA Em circunst ncias normais o fio preto ser a lideran a Quente e o fio branco vai ser Neutro ou Comum chumbo Um verde ou BARE Fio de cobre o terreno Em edif cios mais antigos sempre recomend vel Reconfirme a polaridade de fia o 3 Este dispositivo el trico projetado para ser montado em uma caixa redonda ou octagon padr o A caixa deve ser montada com seguran a para a estrutura do edif cio INSTALA O DE DISPOSITIVO EL TRICO 1 Remova o dispositivo el t
5. nnect the smooth fixture lead to the black wire in the outlet box Fasten the joined wires as in step 7 Slide the canopy and screwcollar ring up the chain and secure the canopy to the ceiling 9 10 Place the shade on the socket cover 11 Install the lamp light bulb NOTE This fixture is rated for 60 watt type B BA or CA lamps DO NOT EXCEED RECOMMENDED WATTAGE 12 Restore power to circuit at breaker or fuse box L CENTER PART lamp Shade HUDSON VALLEY ne LIGHTING stanparo Outlet box Ground Screw _ Nipple Tom Screwcollar loop Ring hain A Electrical tape a Approved fastener Wire nut Hudson Valley Lighting Inc P O Box 7459 106 Pierces Road Newburgh NY 12550 800 814 3993 www hudsonvalleylighting com INSTRUCOES DE INSTALACAO Portugues 8716 GERAL 1 Para garantir o xito da instala o do dispositivo el trico as instru es a seguir e diagrama s deve ser lido e compreendido 2 Todas as liga es el ctricas devem ser feitas de acordo com o National C digo el trico e c digos locais e ordenan as Se voc n o tiver certeza do M todos de instala o de fia o el trica e ilumina o gabaritos proteger os servi os de um eletricista licenciado 3 Ferramentas PRECISAVA Chave de fenda de l mina chave de fenda phillips alicates conjunta de deslizamento ou pequena chave inglesa ajust ve
6. rico tons e partes substituida a embalagem Antes de Descartando o cart o verifique de embalagem para ter certeza de que todas as pe as s o encontrado 2 Retire os 3 parafusos que prendem a placa de montagem para a fixa o 3 Puxe os fios na caixa de sa da atrav s do orif cio central da placa de montagem Conecte a placa de montagem para a caixa de sa da O parafuso terra verde deve enfrentar fora Alinhe a placa de montagem para que o buraco de parafuso inferior exatamente na parte inferior 4 Prenda o fio verde acess rio para o fio de cobre verde ou nua na caixa ou Prenda a placa de montagem com parafuso verde fornecido NUNCA PRENDA O FIO DE TERRA PARA O PRETO OU FIO QUENTE NAO SEGUIR ESTA INSTRU O PODE RESULTAR EM GRAVES LESAO OU MORTE 5 Prenda o fio branco acess rio para o fio branco na caixa de sa da Aperte o fios para juntamente com um fixador aprovado porca de fio Firmemente iniciando cerca de 1 abaixo o fixador quebrar a conex o com fita isolante para que a fita sela o fim do fixador Certifique se de que n o h fios expostos ou vertentes que poderiam causar um perigoso curto circuito 6 Conecte os fios preto acess rio para o fio preto na caixa de sa da Prenda os fios ingressou como na etapa 5 7 Coloque a fixa o sobre a placa de montagem e prender no lugar com o 3 parafusos 8 Colocar os an is na parte superior e inferior do shade s 9 Coloque o shade s para as tampas de soque
7. te 10 Instale o light bulb s de l mpada s Nota Este acess rio classificado para 60 Watts tipo B BA C ou CA l mpada s NAO SUPERIOR A POTENCIA RECOMENDADA 11 Restaure a energia ao circuito no disjuntor ou fus vel caixa HUDSON VALLEY INSTALLATION INSTRUCTIONS HI LIGHTING amp ANDAR 8716 Continued E FINIAL Hudson Valley Lighting Inc P O Box 7459 106 Pierces Road Newburgh NY 12550 800 814 3993 www hudsonvalleylighting com
Download Pdf Manuals
Related Search