Home

GDO Accessories

image

Contents

1. Model 96GC SECURITY 3 Channel Remote Control The 90 Series remote control with yellow battery test light works only with door openers and light controls having an orange Smart button and a yellow indicator light Programming instructions are described and illustrated below The additional push buttons can also activate other garage door openers and or light controls Instructions for programming light products are included with those accessories SECURITY Garage Door Openers To Program the Opener to Accept the Remote Conirol Code Select a remote control push button to operate the opener The arge button is recommended for use with a garage door opener 1 Press and hold the selected remote control push button See Figure 1 2 Press and release the Smart learn button on the opener panel See Figure 2 The indicator light on the panel will begin to blink and the opener lights will flash once 3 Release the remote push button Now the opener will operate when that remote control button is pressed Test it by pressing the remote button to see that the door goes up and down Adding a remote can also be done from the door control as follows 1 With the door closed press and hold a remote push button 2 Press and hold the Light button on the door control 3 Press and hold the door control push bar 4 After the opener lights flash release all buttons Test by pressing the remote push button To E
2. EXISTE AUCUNE AUTRE PIECE SUSCEPTIBLE D ETRE ENTRETENUE PAR L UTILISATEUR Mod le 96GC T l de SECURITY elecomman L j SECURITY ouvre porte de garage T moin lumineux jaune de pile Bouton Smart lectionner un i moi i S lectionner u apprentissage T moin lumineux bouton poussoir Figure 1 Figure 2 Commande de l clairage de l ouvre porte Avec les metteurs SECURITY on peut programmer un bouton poussoir de la t l commande de mani re actionner l clairage de l ouvre porte sans devoir ouvrir la porte 1 La porte tant ferm e enfoncer et tenir le bouton poussoir de la t l commande qui contr lera l clairage 2 Appuyer sur le bouton d clairage de la commande de la porte et le tenir 3 Appuyer sur le bouton de blocage de la commande de la porte et le tenir 4 Lorsque l clairage de l ouvre porte clignote rel cher tous les boutons Faire un essai en appuyant sur le bouton poussoir de la t l commande L clairage de l ouvre porte doit s allumer ou s teindre sans que la porte ne bouge Fonctionnement ouverture fermeture arr t La t l commande SECURITY peut tre programm e de mani re faire fonctionner une porte l aide des trois boutons le gros bouton servira uniquement ouvrir la porte le bouton moyen servira uniquement fermer la porte et le troisi me bouton peut tre r gl e comme suit 1 La porte tant ferm e a
3. commandes d clairage poss dant un bouton Smart orange et un t moin lumineux jaune Des instructions de programmation sont d crites et illustr es ci apr s Les boutons poussoirs suppl mentaires peuvent galement actionner d autres ouvre portes de garage et ou commandes d clairage Les instructions pour la programmation de l clairage sont fournies avec ces accessoires Ouvre portes de garage SECURITY Pour programmer l ouvre porte pour accepter le code de t l commande S lectionner un bouton poussoir de t l commande pour actionner l ouvre porte Le gros bouton est recommand pour usage avec un ouvre porte de garage 1 Appuyer sur le bouton poussoir s lectionn de la t l commande et le tenir Voir Figure 1 2 Appuyer sur le bouton Smart apprentissage du tableau de l ouvre porte et le rel cher Voir Figure 2 Le t moin lumineux du tableau commencera clignoter et l clairage de l ouvre porte clignotera une fois 3 Rel cher le bouton poussoir de la t l commande L ouvre porte fonctionnera d sormais lorsqu on appuiera sur ce bouton de la t l commande Faire un essai en appuyant sur le bouton de la t l commande pour v rifier si la porte remonte et descend L addition d une t l commande peut galement se faire depuis la commande de la porte comme suit 1 La porte tant ferm e appuyer sur un bouton poussoir de la t l commande et le tenir 2 Appuyer sur le bouton d cla
4. irage de la commande de la porte et le tenir 3 Appuyer sur la barre poussoir de la commande de la porte et la tenir 4 Lorsque l clairage de l ouvre porte clignote rel cher tous les boutons Faire un essai en appuyant sur le bouton poussoir de la t l commande Pour effacer tous les codes de la t l commande Appuyer sur le bouton Smart du tableau de l ouvre porte et le tenir jusqu ce que le t moin lumineux s teigne environ 6 secondes Tous les codes de l metteur sont maintenant effac s Suivre ensuite les tapes susmentionn es pour reprogrammer chaque t l commande Pi ces de rechange Bo tier couvercle vis pour la t l commande SECURITY mod le 96GC Pile de 12 volts 41A5018 6 AVERTISSEMENT Les enfants qui utilisent ou qui jouent avec un ouvre porte de garage risquent de se blesser et de blesser les autres La porte risque de se fermer et de causer de graves blessures voire la mort Ne pas permettre aux enfants d utiliser la commande de porte ni les t l commandes Une porte de garage en mouvement peut blesser ou tuer la personne qui se trouve dessous N actionner l ouvre porte de garage que si l on peut bien voir la porte s il n y a pas d obsiruction et si elle est bien r gl e AVIS Conform ment aux r gles de la FCC IC il est interdit de r gler ou de modifier ce r cepteur et ou metteur sauf pour modifier le code ou pour remplacer la pile IL N
5. ppuyer sur le gros bouton poussoir de la t l commande et le tenir 2 Appuyer sur le bouton de blocage de la commande de la porte et le tenir 3 Appuyer sur la barre poussoir de la commande de la porte et la tenir Lorsque l clairage de l ouvre porte clignote rel cher tous les boutons Faire un essai en appuyant sur le gros bouton Ouverture de la t l commande La porte devrait s ouvrir Appuyer nouveau tandis que la porte est ouverte et rien ne devrait se produire Appuyer sur le bouton moyen Fermeture et la porte devrait se fermer Appuyer sur le troisi me bouton Arr t tandis que la porte bouge et elle devrait s arr ter imm diatement POUR LE SERVICE PRI RE DE COMPOSER NOTRE NUM RO SANS FRAIS 1 800 654 4736 1997 The Chamberlain Group Inc 114A2179 Tous droits r serv s Imprim au Mexique
6. rase All Remote Control Codes Press and hold the Smart button on the opener panel until the indicator light turns off about 6 seconds All transmitter codes are now erased Then follow the steps above to re program each remote control Replacement Parts Model 96GC SECURITY remote case cover screw 41A5018 6 circuit board not included 12 Volt battery Children operating or playing with a garage door opener can injure themselves or others The garage door could close and cause serious injury or death Do not allow children to operate the door control or remote controls A moving garage door could injure or kill someone under it Activate the opener only when you can see the door clearly it is free of obstructions and is properly adjusted NOTICE To comply with FCC IC rules adjustment or modifications of this receiver and or transmitter are prohibited except for changing the code setting or replacing the battery THERE ARE NO OTHER USER SERVICEABLE PARTS Model 96GC SECURITY Remote Control SECURITY Garage Door Opener EN 2 C1 Yellow Battery Indicator RCE learn Indicator Light Button Figure 1 Figure 2 To Control the Opener Lights With SECURITY transmitters a remote push button can be programmed to operate the opener lights without opening the door 1 With the door closed press and hold the remote button that you want to control the ligh
7. t 2 Press and hold the Light button on the door control 3 Press and hold the Lock button on the door control 4 After the opener lights flash release all buttons Test by pressing the remote push button The opener lights should turn on or off but the door should not move Open Close Stop Operation Your SECURITY remote control can be programmed to operate one door using all 3 buttons the large button will only open the door the middle button will only close the door and the third button will stop the door s movement You may set up this feature as follows 1 With the door closed press and hold the large remote push button 2 Press and hold the Lock button on the door control 3 Press and hold the door control push bar When the opener lights flash release all buttons Test by pressing the large Open button on the remote The door should open Press it again while the door is open and nothing should happen Press the middle Close button and the door should close Press the third Stop button while the door is moving and it should stop immediately FOR SERVICE DIAL OUR TOLL FREE NUMBER 1 800 654 4736 1997 The Chamberlain Group Inc 114A2179 All Rights Reserved Printed in Mexico Mod le 96GC SECURITY T l commande trois canaux MANUEL D INSTRUCTIONS La t l commande de la s rie 90 avec t moin lumineux jaune d essai de pile fonctionne uniquement avec les ouvre portes et

Download Pdf Manuals

image

Related Search

Related Contents

JLA-16.250 rotor user manual  Quest ISDN Plus Manual  Black-and-White Video Camera Module    FX3UC-4AD INSTALLATION MANUAL    取扱説明書  Samsung SGH-X620 User Manual    GLOSSARIO di ERGONOMIA  

Copyright © All rights reserved.
Failed to retrieve file