Word Class 1 - TE Connectivity
Contents
1. 5 8 2 D h NOT 20 not crimp wi NO Cesignatec Connector Failure to do so may result in a fire by assemDly defect 8 3 8 3 Do not use the tool besides assembly work as hammer or pincer or etc And do not alter the tool 8 4 8 4 Before use check damage in the tool If there IS damage do not USG the tool Fallure to do so may result in a fire by assembly defect 8 5 8 5 Take care the drop of the tool when high place work Failure to do so may result in 8 6 a trouble or an injury 8 6 When operating the handle Please take a care not to pinch the finger Rev A 2 Of 6 Instruction Sheet TE connectivity 408 78056 9 3 Pierc2. Piercing area of the tool Connector Status after setting connector to the tool Fig 2 Fig 2 The process of setting of connector Rec Connector is same as plug Rev A 3 0f 6 by Instruction Sheet EE _ 7 connectivity 9 9 1 9 2 Fig3 Fig 3 9 3 9 4 9 5 408 78056 3 Piercing termination method 9 1 Grip the handle to the ratchet will release Set the handle open with front of the surface that Logo mark on the tool 9 2 Set the connector to the holder of crimping area In a direction of Fig 3 9 3 Grip the handle a little to hold the connector and confirm status of holding 9 4 Grip the handle to the ratchet will releas
3. connectivity 408 78056 6 6 Name of Parts 1 ee Dies Insertion Area Dies Locking Knob INS Piercing Area ed Dies Release Lever Crimpindg Area Fig 1 Name of Parts 7 7 Tool Outline LO This Hand Tool is for assembling Industrial Mini O Connector And tool has piercing termination 6 gt and crimping And also has holder due to be Sa CE CN 5 Refer this instruction sheet Keep tool condition ang correct crimping work 8 8 Attention for work 8 1 8 1 Do not assemble with wire that circuit is running Failure to do so may result in an s lectric shock 8 2
4. 408 78056 Instruction Sheet 25NOV2013 Rev A connectivity INDSUTRIAL MINI IO PIERCING TYPE HAND TOOL 1 1 Introduction IO his manual describes the piercing termination 3nd the crimping INDSUTRIAL MINI I O procedure PP 2 with HAND TOOL Read this manual thoroughly before crimpin9 work 2 2 Applicable Products Part No Descriptions 2229737 1 INDSUTRIAL MINI IO PIERCING TYPE HAND TOOL 3 3 Applicable Connector and Cable Refer Application Specification for details 4 4 Related Documents 114 5506 114 5506 Application Specification 5 5 Tool Specification 460g Tool Weight 460 0 2013 Tyco Electronics Japan GK Trademark TE Connectivity td9 10f16 a TE Connectivity Ltd Company All Rights Reserved TE logo is a trademark Other products logos and company names might be trademarks of their respective ownerS LOC B Sb Instruction Sheet TE
5. e 9 5 Open the handle And take out the connector and check the terminal Appearance I Holder NN I NAS MN LS Rl Crimping area of the tool Status after setting connector NN to the tool N Direction of the connector Fig 3 Fig 3 The process of setting of connector Rev A 4 of 6 Instruction Sheet EE _ 7 connectivity 408 78056 10 10 Dies remove method 10 1 4 Fig 4 10 1 NN 1 to 4 steps from open 10 2 IS Fig 5 10 2 During move Dies Locking Knob to the handle side withdraw Dies Fig 5 FIg 4 Fig 4 10 10 Dies fixing method 10 1 4 Fig 4 10 1 Close the handle to 4 steps from open 10 2 NOC rd x 10 2 During move Dies Locking Knob to the i handle side The slot of Dies and
6. ing termination method 9 1 9 1 Grip the handle to the ratchet will release Set the handle open with front of the surface that Logo mark on the tool Ne 6 he sl CABLE HSG h 92 II Ba J tool Pa a Fig 2 and bottom in a connector Fig 2 9 3 9 3 Grip the handle a little to hold the connector and confirm status of holding 9 4 9 4 Grip the handle to the ratchet will release with nold the connector to avoid wire position move 9 5 ip DIN a Slot of CABLE HSC Convex of Piercing area Tool
7. the convex Of Dies Insertion area are set and Inserted Fig 6 Rev A S 0f 6 Instruction Sheet EE _ 7 connectivity 408 78056 10 10 Care for Tool Push Release lever when canceling on the way Fig 7 of assembly Fi9 7 Fig 7 10 10 Care for Tool 10 1 10 1 Remove the dust at anvil and crimper point with Air Gun 10 2 1000 1 10 2 Oil the designated point In machine oll every Fig 8 1 000 times of steering wheel opening and shutting once Fig 8 Oil filling poin Fig 8 Rev A 6 of 6
Download Pdf Manuals
Related Search