Instruction Manual for
Contents
1. For safe handling of the product please read the following precautions carefully before use Failure to heed the precautions listed below could result in serious consequences To prevent injury or damage to yourself and or others please observe the precautions as they contain highly important information related to personal and product safety Z WARNING Situations that could result in severe injury or death CAUTION Situations that could result in property damage or personal injury AM WARNING e Keep out of reach of children to prevent accidental ingestion If swallowed seek medical advice immediately Z CAUTION Carefully observe the instruction manual for the compatible camera for this product before use e Unauthorized disassembling and or modification could result in malfunction or flooding and void product warranty Take the product to a SEA amp SEA authorized service center for repair or inspection Should you notice smoke or an unusual smell coming from the product turn it off and remove the batteries immediately taking care to avoid burns Continued operation could result in injury After removing the battery take the product to a SEA amp SEA authorized service center for inspection e Discontinue use and turn the product off immediately should you notice flooding or leakage When the product is flooding interior pressure may build up Please be careful when opening the product as water may sp2. O ring maintenance manual for the handling of O rings before use Accessories Before using this model check to make sure that all accessories are present DK 2G LCD Monitor Hood Hand Strap BU ap 2 Desiccant Pack Sillicon Grease O ring remover Silica Gel Za D Optical Fiber Adapter e O ring Maintenance Manual e DX 2G Instruction Manual this manual Identification of Parts Power button Shutter lever Mode dial Accessory shoe Fn function button Diffuser dial Up down dial Grip Wide angle conversion lens string eyelet ADJ dial co A MODE button CAJT telephoto Enlarged view button CJW wide angle Wi gt Thumbnail display button AF Flash lamp window U A IMA 58 MENU OK iS 12 button LCD monitor Bk hood string eyelet I ssi LCD monitor IS hood holder ss Hand strap hook ji Playback button B Flash button 3 DISP button WI Macro button Quick review button Go Delete Self timer button E 5 Opening the Rear Cover 1 Push the red buckle lock buttons together to unlock and pull the buckle all the way towards back to lift the rear cover from the front case 2 Pull the rear cover to open Z CAUTION e Before opening the rear cover make sure that the housing is completely dry and free of salt deposits If you find any salt deposits rinse with fresh water and wipe off
3. water completely with a soft cloth e Never use the buckle buckle lock buttons underwater When opening the rear door after use in the water open it carefully not to let water or sand enter inside the housing Installing the 2G Camera Flash OPEN switch e Before installing the 2G camera slide the Flash OPEN switch to the outside to raise the flash cover open the flash and remove the lens cap from the camera Turn off the power of the camera before installation e This housing is only compatible with the 2G camera 1 Turn off the power of the 2G camera and place it as shown in Fig 1 2 Make sure that there is no dust or scratches on the O ring O ring contact surface before closing the rear cover Take the hand strap out press the rear cover and then put the buckle over the front case Fig 2 3 Push the buckle down until it clicks Make sure that the red buckle lock buttons on both sides are popped out Fig 3 Z CAUTION To avoid flooding by trapping remove the wrist strap from 2G camera before installation e Never install or remove the 2G camera while the camera is ON The ejected lens may interfere with the housing and damage the camera and lens e Make sure that the 2G camera is set parallel to the housing and not excessively slanted E 7 Power button Power button Use the power button to turn ON OFF the 2G camera Shutter lever Depress the shutter lever to press the shutter button of t
4. SEAcSEA je UNDERWATER DIGITAL CAMERA HOUSING BY ten HAS Instruction Manual Introduction Thank you for purchasing SEA amp SEA products Please read this instruction manual carefully prior to using your underwater housing Only with a thorough understanding of this manual s content will you be able to use the housing correctly After reading the manual please be sure to keep it in a place where you can easily come back to it at any time Pressure resistance inspection sticker PRESSURE TES PASSED EAcSEA Products bearing this sticker are those that have passed SEA amp SEA s criteria based inspection for pressure resistance Safety Precautions wi ai mera ei even vies ewes E 2 ACCOSSONOS iena AAA WAPA PAA AAA AAA WW E 4 Identification Of AE ien ia va aj a E 5 Opening the Rear COVEr nn nnnenenennn ena ne nn nn nn E 6 Installing the 2G Camera ne ence eset nn nn nznnna E 7 OPEN e a steedeeteas E 8 LED monitor hod IA ENEE EE EEEREN EEES E 9 ANG SUAD Ia E 9 Built in flashlight diffuser s sess eeennennnnzennnznzennanzani E 10 Optical fiber adapter w wwwwannwwannaa E 10 Desiccant pack Silica Ma E 11 Attaching the Optional AccessorieS E 12 Attaching accessories to the bayonet E 12 Accessory shot AA E 13 Maintenance and Storage ern nennenz nn nn nazz rna nn E 14 SPA ori lo f E 15 E 1 Safety Precautions
5. Turn the close up lens clockwise until it clicks Align the salient and O mark Z CAUTION e When using the lens loosen or lightly shake the lens while underwater to remove any air trapped between the lens and the housing E 12 Attaching the Optional Accessories H Accessorv shoe SEA amp SEA strobes lights can be lt Example gt mounted to the accessory shoe by using optional Mini Shoe Arm 29511 or Hot Shoe Arm 29501 CAUTION The max weight of an accessory that can be mounted to the accessory shoe is approx 750g 26 30z equivalent to the weight of SEA amp SEA YS 110 strobe Remove the accessories from the accessory shoe when carrying the housing out of water Maintenance and Storage Z CAUTION Never use chemicals cosmetics any petroleum solvents such as paint thinner or neutral detergent on the product They may deform and damage the product After each use in salt water make sure it is watertight then soak it sufficiently in fresh water and rinse with running water Operate all the buttons dials or levers underwater but do not operate the buckle buckle lock buttons e Insufficient soaking causes damage by salt to the product Salty residue may be left on the product where it will crystallize as it evaporates Crystallized salt is hard to dissolve and difficult to be removed once formed and it will result in water leakage After rinsing dry the product well with a sof
6. ed weight of the accessories may damage the strap and the strap hook which may result in equipment damage loss or personal injury E 9 Operation B Built in flashlight diffuser Turning the dial forward sets the built in flashlight diffuser inside the flash window The diffuser disperses and softens light from the built in flash of the 1G camera It helps prevent backscatter that is it reduces light reflection from particles in the water rss A oS ZAR e The camera s built in flash cannot illuminate the subject uniformly due to the structure of the housing Use of an external strobe is recommended H Optical fiber adapter When using an optional external strobe with this housing please use the optical fiber adapter supplied with this housing for proper connection Firmiv attach the optical fiber adapter to the housing first and insert the fiber optic cable into the adapter as far as it will go If vou directiv insert the fiber optic cable into the housing without the adapter the connected external strobe mav operate erraticallv ANCAUTION e External strobes made by companies other than SEA amp SEA SUNPAK Co Ltd are not guaranteed to operate properly The SEA amp SEA YS 110 strobe may malfunction even if the optical fiber adapter is used E 10 Operation H Desiccant pack Sillica Gel A substantial difference between the external water and the internal camera and air temperatur
7. es sometimes result in dewfall on the inside surface of the housing lens This phenomenon tvpicallv happens when the camera becomes hot due to long and consecutive use To mitigate the effect of the dew use the desiccant pack included in the product package as follows Using the desiccant pack Sillica Gel 1 Install the 2G camera to the housing 2 Place a desiccant pack Sillica Gel at the location as shown then close the rear cover Z CAUTION e Make sure that the edge of the desiccant pack is not covering the O ring contact surface Make sure thet the desiccant pack is not trapped when closing the rear cover Attaching the Optional Accessories This product accepts SEA amp SEA optional accessories By using this product in combination with those accessories you will be able to try various shooting techniques e Lenses strobes and other accessories have different depth rating Check the depth rating for each before use Read the instruction manual for each accessory before use H Attaching accessories to the bavonet SEA amp SEA optional accessories can be attached to the bayonet on this housing Refer to our website or product catalog for detailed information on compatible accessories Example How to attach the wide angle conversion lens for DX 1G 52116 1 Align the salient on the upper surface of the housing lens and the mark on the lens bayonet then impose the close up lens to the housing 2
8. he 2G camera Shutter lever Mode dial Turning this dial changes the shooting mode Mode setting status is displayed at the top center of the LCD monitor of the 2G camera Mode dial Up down dial Turning this dial rotates the up down dial on the 2G camera Use this dial to work with the menu and to change aperture or setting value quickly and easily Up down dial ADJ dial ADJ dial Pushing and flicking this dial to the right and left operates the ADJ lever of the 2G camera Other buttons Use buttons to control each function of the 2G i camera underwater Please refer to the Other buttons instruction manual of the 2G camera for operation of the other buttons Operation H LCD monitor hood 1 Putthe LCD monitor hood string through the rear cover eyelet as shown 2 Mount the LCD monitor hood to the holder Z CAUTION e Please be careful not to get the strap of the LCD monitor hood caught in the rear cover when closing e Do not hold the LCD monitor hood to carry the housing It may come off and the housing may fall down ii Hand strap Attaching the hand atrap Put the hand strap through the hook on the housing let other end go through between the strap and pull the strap tight as shown A A KS N WINS In e Do not use the strap when out of water if using optional accessories such as a wide angle conversion lens stay arm and strobe light The increas
9. ht seal When packing the product for airplane travel do not seal up the product to alleviate pressure build up due to atmospheric changes e Never use chemicals cosmetics any petroleum solvents such as paint thinner or neutral detergent on the product They may deform and damage the product Do not leave the product in places with hot temperatures such as inside of a car or in a car trunk in summer The heat may deform plastic parts of the product damaging internal parts and resulting in potential fire or electric shock If the product is sealed tight in hot conditions heated air expanding inside the product may deform the casing and ruin the waterproofing Do not store the product in wet or high humidity place to avoid mold rust corrosion or malfunction e Do not store the product with naphthalene or camphor mothballs or in locations such as a laboratory where chemicals are used This environment can cause mold rust corrosion or malfunction SEA amp SEA SUNPAK Co Ltd assumes no liability for compensation of loss of captured images or expenses caused by loss of images even if you are unable to shoot due to a product defect or malfunction SEA amp SEA SUNPAK Co Ltd will not be responsible for the replacement or compensation for cameras lenses or those accessories damaged due to your invalid operation e SEA amp SEA SUNPAK Co Ltd assumes no liability for errors or discrepancies in this manual e Carefully observe the
10. onstruction Body Polycarbonate Grip ABS resin Depth rating 55m Dimensions Apporox 158 W x109 h x109 D mm 6 3x4 4x4 4 inches Weight Apporox 510g 17 90z housing only Apporox 110g 3 90z underwater Accessories LCD monitor hood O ring remover Desiccant pack Silica Gel Hand strap Silicone grease Optical fiber adapter O ring maintenance manual Instruction manual The specifications and appearance are subject to change without notice E 15 D WA CG ti way SEAcSEA YP YEY Hv Ny PRN SH SEA amp SEA SUNPAK Co Ltd 7332 0016 EF Or 3287 3 2 20 3 2 20 Saiwai cho Kawaguchi shi 956 Saitama Japan 332 0016 1 yap aaa ge TEL 481 48 256 2251 NAI YAI World Customer Service Center TEL 048 255 8512 TEL 81 48 255 8512 http www seaandsea co jp http www seaandsea jp 0817 Z 01
11. t dry cloth then let the product dry in the shade out of direct sunlight Do not dry the product by heating using a hair dryer for example Heating can deform and damage the product If you will not use the product for an extended period of time store it away from high temperatures high humidity direct sunlight or exterme cold Do not store the product with naphthalene or camphor mothballs or in locations such as a laboratory where chemicals are used This environment can cause mold rust corrosion or malfunction Always remove the camera from the housing after use Thoroughly wipe off water before opening the housing and avoid any water drops inside the housing After using the product maintain the O rings before storing Examine the O rings before and after each dive We recommend early exchange of the O rings at least once a year Every two years we recommend a complete overhaul of O rings regardless of the frequency in use for the best performance of the product E 14 Specifications Compatible camera 2G Controls Power button Shutter lever Mode dial Up down dial Diffuser dial Fn Function button Playback button Quick review button amp Delete Self timer button W Macro button MENU OK button 2 A MODE button P Flash button 8 DISP button LI W wide Thumbnail button CIT telephoto Enlarge display button ADJ dial C
12. urt out or the cap may open explosively and cause injuries e Do not open the chassis or battery cap in the vicinity of open flames The product has been constructed with an airtight seal When packing the product for airplane travel do not seal up the product to alleviate pressure build up due to atmospheric changes Do not open the product in a wet or sandy environment Protect the interior from moisture and debris in order to prevent malfunction or flooding E 2 Safety Precautions e Avoid strong shocks impacts or excess stress to prevent malfunction damage or breakdown Make sure that the product has been securely mounted to other products in order to prevent injury fall or missing Do not rest heavy weight on the product It might deform the outer casing damage internal parts make the waterproofing fail or result in fire or electric shock Please note that some marks may be left on the camera scraping against the dials or gears of the housing Handle the product carefully so as not to scratch the front port the lens the flash window or the finder e Always dry the front port the lens the flash window or the finder using a soft cloth to prevent stain or salt residue from marring the surface Rinse the product with fresh water after underwater use Ensure that the product is waterproofed before rinsing Refer to Maintenance and Storage P E 14 for details The product has been constructed with an airtig
Download Pdf Manuals
Related Search