LED 電源取扱説明書 - Shindengen
Contents
1. 30 C 65 C le eee 88C RR 8 102. A JEE 85 264VAC 1 45 65Hz RB KKO LED RB RRO
3. HS150S9FR 1 1 2kg 1 2 Ba 1 88C 2 8 amp LED 3 2 4 M4 1N m 5
4. LED Power Supply Instruction Manual HS150S9FR series Read this instruction manual carefully to ensure the correct use of the product As a qualified electrical engineer is required to install this product ask an electrical contractor To electrical contractor After the work has been completed return this instruction manual to the customer SAFETY PRECAUTIONS e This product is intended for LED illumination Never use this product for any purposes other than LED illumination e Following symbols are used to indicate and explain the degree of danger or damage that could arise when the product is used incorrectly AN Indicates that there is a risk of death or serious WARNING f injury if the precautions are not observed STORAGE PRECAUTIONS A e Do not store this product in a hot humid place CAUTION INSTALLATION PRECAUTIONS e Installation work must be performed by experienced personnel with adequate technical knowledge Otherwise electric shock or fire may result e Installation work must be performed correctly according to AN this instruction manual If the installation is inappropriate WARNING electric shock or fire may result e This product must be installed correctly on a base that can sufficiently tolerate the weight of the product If the base does not have sufficient strength the product may fall down and cause injuries USAGE
5. D 115381 2 AC li LED _ Vin 120 240VAC Vin 100 120VAC Vin 120 240VAC ae a0 0 100 120 150 W 3 24V 48 C 220 32 5 32 5 o Yd M4 M4 5 4 3 6 LED FG DC LED FG B 6
6. mounted on the wall 3 CONNECTING THE PRODUCT e Connect the product with the input power turned off e Connect such as current limit resistor or constant current driver or some circuitry which can limit forward current of LED since this product is constant voltage output See Figure 6 e If an extension cable is to be used use a wire that conforms to the voltage and current specifications of this product e Do not connect the output cables of multiple units of this product in series or in parallel e Always ground this product with the FG cable Power supply unit Current Limit White AC N Circuitry Ep White DC Black AC L Black DC Green Yellow Cannot be mounted on the ceiling Figure 5 FG Figure 6 Manufactured by Shindengen Electric Manufacturing Co Ltd For any queries about this product please contact your nearest local dealer
7. LED LED LED
8. PRECAUTIONS Do not remove screws from the product open the casing or disassemble or alter the product Otherwise failures electric shock or fire may result e For the input voltage use only sine wave alternating current A N and do not use any power voltages or frequencies other than WARNING the specified range 85VAC to 264VAC single phase 45Hz to 65Hz Otherwise electric shock or fire may result e Always connect an LED that conforms to the output voltage and output current of this product Otherwise failures electric shock or fire may result e Do not drop this product or apply shock to it A CAUTION where volatile or inflammable gases are generated OTHER PRECAUTIONS e Each series of this product adopts different safety AN standards that prescribe different operation environments CAUTION Use the product in accordance with the safety standards for the series of that product A CAUTION e Do not use this product in a place subject to direct sunlight or Indicates that there is a risk of personal injury or physical damage if the precautions are not observed e Do not store this product in a place subject to direct sunlight vibrations or corrosive gases e Installation work must be performed with the input power turned off Otherwise electric shock or fire may result e Avoid installing this product in a place where the input and output cables can be scratched If the product is used with th
9. e cables scratched electric leaks electric shock or fire may occur e Do not apply excessive load on the input and output cables by bending pulling or twisting the cable or placing an object on the cable Otherwise a short circuit or broken wiring could cause fire or electric leaks e Use this product within an ambient temperature range of 30 C to 65 C If this product is used outside this range failures or fire may result Here ambient temperature means the ambient temperature of this product which is the temperature inside the lighting equipment If this product is used in a narrow place where there is no air circulation and heat is easily trapped make certain that the temperature of the casing of this product does not exceed 88 C elf this product fails and generates an offensive odor or abnormal sound during operation immediately stop using the product e The service life of this product differs with the working conditions As a guide the replacement interval is between 8 and 10 years e Dispose of this product in accordance with the disposal method prescribed by the local government INSTALLATION METHOD D 115381 2 1 PRE INSTALLATION CHECK e Ensure that the base where this product is installed has Building material etc sufficient strength to tolerate the weight of this product Ambient environment of power supply unit approx 1 2 kg Power supply unit e For the ambient e
10. nvironment of the product as shown in Figure 1 pay special attention to the following notes so that the temperature measurement point shown in Figure 1 Figure 2 does not exceed 88 C 9 If two or more products are installed side by side provide sufficient space between them to prevent the heat generated by each product from affecting the others Provide sufficient space between this product and the LED module to prevent the heat generated by the LED module from affecting the product If the product is to be placed in a casing note that the capacity of the casing must be sufficiently large to prevent the product from overheating Do not cover this product with heat insulating materials or soundproofing materials 9 P 9 tc The rated maximum Top view temperature of the casing ta The maximum ambient temperature 220 The output power is limited by ambient temperature as shown in figure 3 Figure 2 Be sure the operating conditions before using this product Vin 120 240VAC bo 32 5 32 5 Oo Ambient Vin 100 120VAC M4 screw M4 screw Temp s Vin 120 240VAC Top view E M4 screw T TT M4 screw 48C for 24V output Output Power W Side view Figure 3 Figure 4 2 INSTALLING THE PRODUCT e Tighten M4 screws at the specified positions to a tightening torque of 1N m or less as shown in Figure 4 e Do not place a ceiling over the product as shown in Figure 5 The product can be
Download Pdf Manuals
Related Search