取扱説明書／240KB
Contents
1. 5 RU 1 D 6 D AC 2 5m Oo Oo2. oO 2 Oo 3 10 5 5 10 15 207 25 8 4 AC fE _ AC 35kg AC 20kg AC 3 15A
3. 15kg 440W x550D mm i 33kg AC 15A oO A MAX 125V 2 Fixing the Frames Fix the right and left frames to the base with the hex socket head bolts as illustrated below using the hex bar wrench INSTRUCTION MANUAL When doing this fix the hex socket head bolts tentatively lightly and do not fully tighten them MODEL 997 WAGON HEX SOCKET HEAD BOLT 1 Assembly Method of Wagon 1 Unpacking the Wagon Unpack the packed wagon and you will find components as follows j o FLAT WASHER xs SPRING WASHER ie i HEX SOCKET HEAD BOLT 8 3 Fixing the Auxiliary Table O AUXILIARY TABLE Fix the auxiliary table between the right and left frames with the hex socket head bolts as illustrated below using the hex bar wrench When doing this fix the hex socket head bolts tentatively lightly and do not fully tighten them FLAT Sc WASHER HEX SOCKET SPRING HEAD BOLT WASHER O LEFT FRAME O RIGHT FRAME _ 4 Fixing the Table Fix the table between the right and left frames as follows Pull out and remove the drawer from the table Between the right and left frames place the table by holding it by its rig
4. time Caution Do not carelessly pull the clutch bars when the table is loaded with an instrument 2 Confirm that the clutch bars return to the locked positions as you release your hands from them If they do not return to the locked positions slightly move up and down the handles to held their return Placing an Instrument Place an instrument on the table and fix the instrument with the clamp belt Note Be sure to pass the clamp belt through the handle or handles on top or sides of the instrument Tilting the Table You may tilt the table instrument to an angle most conve nient for viewing To do this proceed as follows Hold the right and left handles outsides pull the clutch bars in sides to your side tilt the table to one of the below mentioned angles and then release the clutch bars Selectable angles 10 5 0 level 5 10 15 20 and 25 degrees Eight angles AC Receptacles The wagon at its rear has three AC outlet receptacles for the instruments placed on the wagon Connect the input power cord of the wagon to an AC line outlet and the AC outlet re ceptacles will deliver AC outputs up to 15 amperes in total Note The wagon itself is not connected to the ground line of the AC power 1 TABLE 2 HANDLE 3 CLUTCH BAR 4 CLAMP BELT 5 PROBE HOLDER 6 AUXILIARY TABLE 7 BASE 8 AC RECEPTACLES 9 AC INPUT POWER CORD 10 FRAME APPROX 2 5 METERS LONG 3 Specifications Allowable Load 35
5. MODEL 997 WAGON 1 o Oo O O O M6 X20 Gy DS Fe ER M6SW M6 PW CRY b hh D AC 3P 2P 16 12 10 2 1 1 1 2 x pP TN 2 is a ee j A Kaa N 3 An 4 6
6. ht and left handles outsides in the state that the clutch bars insides are pulled to your side the state that the clutch shafts are retracted Adjust the table to level release the clutch bars and insert the clutch shafts into the holes of the right and left frames Insert the pivot disks and fix them with the hex socket head bolts Keeping the table level fix the stopper bolts hex socket head bolts as illustrated below O ACCESSORIES HEX SOCKET HEAD BOLTS M6 x20 16 SPRING WASHER HEX SOCKET EunD 4 HEAD BOLT oo SPRING WASHERS M6SW 12 SN vi s gt ee SPRING WASHER FLAT WASHERS M6PW 10 RR AO FLAT WASHER 9 X PIVOT DISKS 2 9 HEX BAR WRENCH 1 5 Tightening the Bolts After making sure that the wagon operates normally by AC PLUG ADAPTOR 3P 2P 1 referring to B Operation Method of Wagon fully tighten the hex socket head bolts which fix the right and left frames to the base and which fix the auxiliary table to the right and INSTRUCTION MANUAL 1 left frames using the hex bar wrench 2 Operation Method of Wagon 1 Setting the Table to Level 2 3 4 Adjust the table to level by holding the right and left handles outsides and pulling the clutch bars insides to your side so that the clutch is released and the table can be tilted Release the clutch bars when the table is set to level Notes 1 Note that the clutch is not released unless you pull both right and left clutch bars at the same
7. kg Table 20 kg Auxiliary Table 15 kg Dimensions of Table Approx 440 mm W 550 mm D Weight of Wagon Approx 33 kg Total Output Current Rating of Receptacles 15 amperes MAX 125 V KIKUSUI ELECTRONICS CORP
Download Pdf Manuals
Related Search