Samsung GSLS1100A0WW User Manual
Contents
1. PLUG THE POWER CORD INTO A 7 REMOVE THE PROTECTIVE FILM GROUNDED OUTLET COVERING THE CONTROL PANEL Insure proper ground exists before use READ THE REST OF THIS OWNER S MANUAL RUN THE WASHER THROUGH A It contains valuable and helpful information that will COMPLETE CYCLE save you time and money Check for water leaks and proper operation OWNERS MANUAL NOTE If your washer does not operate please review the Before You Call For Service section ALCOVE OR CLOSET INSTALLATION If your washer is approved for installation in an alcove or closet there will be a label on the back of the machine describing requirements mM E sq Minimum clearances between washer and adjacent 387 1 sq cm walls or other surfaces 0 either side 2 front 3 rear Minimum vertical space from floor to overhead shelves cabinets ceilings etc is 96 Closet doors must be louvered or otherwise ventilated and have at least 60 square inches open area for washer only or if the closet contains both 60 sq in a washer and dryer doors must contain at least 120 387 1 sq cm square inches of open area equally distributed NOTE The clearances stated on this label are minimums Consideration must be given to Closet door providing adequate clearances for installation and servicing 12 Installation Instructions WASHER CONNECTIONS FOR PORTABLE MODEL GSLP1100 ONE FAUCET CONNECTIONS U2. Water leaks Water temperature is incorrect Water won t drain www geappliancescanada com POSSIBLE CAUSES WHAT TO DO Type of detergent Switch to a lower sudsing detergent brand and follow instructions on package Very soft water Try less detergent Too much detergent Measure your detergent carefully Use less soap if you Fill hoses or drain hose is have soft water a smaller load or a lightly soiled load Make sure hose connections are tight at faucets and the improperly connected washing machine Make sure the end of the drain hose is correctly inserted in and secured to the drain Household drain may Check household plumbing You may need to call be clogged a plumber Constant water pressure Tighten hoses at the faucets and turn the water off to the fill hoses at the after each use water source Check condition of the fill hoses they may need replacement after 5 years Using too much detergent in washer Water supply is turned off or improperly connected Use less detergent Use less soap if you have soft water a smaller load or a lightly soiled load Turn both hotand cold faucets fully on and make sure hoses are connected to correct faucets Water valve screens are stopped up Turn offthe water source and remove the water connection hoses from the upper back of the washer Remove screens and use a brush or toothpick to clean the screens in the machine Reinst
3. rips or excessive wear Wrinkling NOISE Washer is noisy Dragging noise prior to water filling in the tub OTHER Labels on the exterior of the washer will not peel off cleanly POSSIBLE CAUSES Pins snaps hooks sharp buttons belt buckles zippers and sharp objects www geappliancescanada com WHAT TO DO Fasten snaps hooks buttons and zippers Remove loose items like pins objects in pockets and sharp buttons leftin pockets Turn knits which snag easily inside out Undiluted chlorine bleach Check bleach package instructions for proper amount Never add undiluted bleach to wash or allow clothes to come in contact with undiluted bleach Chemicals like hair bleach Rinse items that may have chemicals on them before or dye permanent wave solution washing Improper sorting Avoid mixing heavy items like work clothes with light items like blouses Trya fabric softener Overloading or Load your washer so clothes have enough room incorrect water level to move freely Repeated washing in Wash in warm or cold water water that is too hot POSSIBLE CAUSES WHAT TO DO Washer is uneven Level the washer See Leveling the Washer Washer load is Press the START PAUSE button to stop the washer open unbalanced the lid and redistribute the load evenly Close the lid and restart Washer is sitting too close to wall causes knocking during cycle When using the LOAD S
4. CYCLE These wash cycles control the length of the washing process The chart below will help match the WASH CYCLE setting to your specific laundry needs When a cycle is selected the automatic temperature that the machine defaults to can be changed to whatever temperature you desire Safety Instructions Default Wash Rinse Temperatures COLOURS For easy care and wrinkle resistant items WARM COLD WHITES For heavy to lightly soiled cotton household HOT COLD linens towels work and play clothes DELICATES For lingerie and delicate fabrics with COLD COLD light to normal soils Operating Instructions QUICK WASH For one or two lightly soiled items WARM COLD that are needed quickly 5 TEMP WASH RINSE Select the water temperature for the wash and rinse cycles Always follow fabric manufacturer s care label or instructions when laundering NOTE FOR PORTABLE MODELS When using a one faucet connection adjust the water flow mix and water temperature at the faucet 2 START PAUSE Press the START PAUSE button to start the wash cycle Lc S S E E S p TIME REMAINING Displays the time remaining in the wash cycle It will also display Status Indicators See Troubleshooting Tips NOTE When the cycle is complete the control panel will turn off automatically Troubleshooting Tips Consumer Support Loading and using the washer Always follow fabric manufacturer s care label when laundering
5. Electrical Codes or prevailing local codes and ordinances This appliance must be supplied with the voltage and frequency indicated on the rating plate located on the back of the washer and connected to an individual properly grounded branch circuit protected by a 15 or 20 amp circuit breaker or time delay fuse If the electric supply provided does not meet the above requirements call a licensed electrician Insure proper ground exists before use GROUNDING INSTRUCTIONS This appliance must be grounded In the event of a malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electrical current This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances DANGER Improper connection of the equipment grounding conductor can result in a risk of electrical shock Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded Do not modify plug with this appliance if it will not fit the outlet installed have a proper outlet installed by a qualified electrician 10 LEVELING THE WASHER STATIONARY MODELS Before connecting the hoses the washer must be level Leveling locks are located at the bottom front of the left and right
6. www geappliancescanada com Sorting Wash Loads Sort by color whites lights colors soil level fabric type sturdy cottons easy care delicates and whether the fabric produces lint terry cloth chenille or collects lint velveteen corduroy Proper Use of Detergent Add clothes and detergent then start the washer You can use less detergent ifyou have soft water Q C Using too little or too much detergentisacommon a smaller load or a lightly soiled load cause of laundry problems 21 lt Loading the Washer Load dry items loosely no higher than the top row W Do not wrap large items like sheets around the of holes in the washer tub When loading wet items agitator make sure you set the load water level high enough to allow the items to move freely Water level should just cover the clothes To add items after washer has started open the lid and add the additional items W When the lid is up a signal will sound and Lo will W Do not wash fabrics containing flammable materials waxes cleaning fluids etc Close the lid Washer will start automatically appear in the display The washer will not agitate with the lid up M 5 and Cleaning of the Washer IN Wash Basket Leave the lid open after washing to Moving and Storage Ask the service technician to allow moisture to evaporate Ifyou want to clean remove water from drain pump and hoses Do not basket use a clean soft cloth dam
7. ENSING feature the agitator rotates before water fills in the tub POSSIBLE CAUSES Occasionally the adhesive used on the labels does not release cleanly Pull washer away from the wall about 4 11 cm is needed This is normal WHAT TO DO Use a hair dryer set at the lowest heat setting directing the air at the label for a short amount of time This will release the adhesive easily without damaging the surface of the washer 19 suoyonysuy ajes e LI 9 A S Q S A E eo 3 A S Q S L7 sdij Buioousa qnoa yioddngs Q N sdij Gunooysajqnoy pioddngs Notes suononysuy suo n nysuj Guyesadg suoranajsu uonejjejsu GE Washer Warranty All warranty service provided by our Factory Service Staple your receipt here Ca Centers In Canada call 1 800 361 3400 Proof of the original purchase date is needed to obtain service under the warranty For The Period Of We Will Replace One Year Any part of the washer which fails due to a defect in materials or workmanship During this From the date of the full one year warranty GE will also provide free of charge all labor and in home service to replace original purchase the defective part Five Years The transmission if it should fail due to a defect in materials or workmanship During this From the date of the additional four year l
8. ESIRED TEMPERATURE SETTING UNPLUG POWER CORD AND RETURN IT TO THE STORAGE AREA PLUG THE POWER CORD INTO A 3 PRONG GROUNDED OUTLET The electrical power cord is on the back of the PRESS THE RED WATER FLOW wapna BUTTON TO RELEASE THE WATER PRESSURE Insure proper ground 0 Water exists before use Button REMOVE THE PROTECTIVE FILM Hose Connector COVERING THE CONTROL PANEL Installation Instructions DISCONNECT FROM WATER LINE Move the locking collar down and pull the hose connector down to disengage from the faucet adapter Locking Collar Hose Connector DRAIN WATER Drain water from the hoses through the hose connector WASHER CONNECTIONS FOR PORTABLE MODEL GSLP1100 TWO FAUCET CONNECTIONS If you have two separate water connections your washer can be connected to both the hot and cold water faucets This kit can be purchased from your dealer or from Parts and Accessories In the United States call 800 626 2002 In Canada consult the yellow pages for your local Camco number TO CONNECT THE WASHER CONNECT TO WATER LINE Connect HOT and COLD water inlet hoses to the HOT and COLD faucets CONNECT DRAIN HOSE Secure the drain hose to the sink or stand pipe SS y g E O Ej y CS Q Y e Cable Tie KG P Stand Pipe PLUG THE POWER CORD INTO A 3 PRONG GROUNDED OUTLET Insure pro
9. TE When using the LOAD SENSING feature it is normal for the agitator to rotate before water fills in the tub To choose the automatic LOAD SENSING feature press ON OFF The following indicators will light up automatically NORMAL LOAD SENSING and COLD COLD Then simply press START PAUSE E z 3 A S Q S 77 A m a 3 a A S Q S 7 To Choose Your Own Cycle Selections 7 ON OFF Press the ON OFF button to turn on the control panel WASH OPTIONS Choose the wash options you would like to include in the cycle Press the WASH OPTIONS button until all the options you want to include are lit More than one option can be selected sdij PRESOAK For heavily soiled clothes that need to be soaked before washing This option can be used as part of the WASH CYCLE you select NORMAL This option is automatically selected when you press ON OFF RINSE ONLY This option gives one rinse cycle only For example Use this cycle when you need to remove excess detergent from your clothing SPIN ONLY This option gives one spin cycle only For example Use this cycle when you need to remove excess water from your clothing pioddngs About the control and indicator settings LOAD SIZE The water level should just cover the clothes Adjust the load size accordingly Loosely load clothes no higher than the top row of holes in the washer basket WASH
10. WHEN USING THE WASHER E Never reach into washer while it is moving Wait E The laundry process can reduce the flame until the machine has completely stopped before retardancy of fabrics To avoid such a result opening the lid carefully follow the garment manufacturer s i wash and care instructions Use this E Do not use sharp objects around the control panel They may damage it E To minimize the possibility of electric shock unplug this appli from th r ly or disconnect only for its not mix chlorine bleach with ammonia or acids UA ue the washer at the household distribution panel by intended such as vinegar and or rust remover Mixing removing the fuse or switching off the circuit breaker before attempting any maintenance described Mb cleaning NOTE Turning the washer off does NOT this Owner s E Do not wash or dry articles that have been disconnect the appliance from the power supply Manual cleaned in washed in soaked in or spotted with combustible or explosive substances such as wax oil paint gasoline degreasers dry cleaning solvents kerosene etc which may ignite or explode Do not add these substances to the wash water Do not use or place these substances around your washer or dryer during operation purpose as different chemicals can produce a toxic gas which E Never attempt to operate this appliance if it is damaged malfunctioning partially disassembled o
11. all screens reconnect the hoses and turn the water back on House water heater is not set properly Drain hose is kinked or improperly connected Make sure house water heater is delivering water at 120 F 140 F 48 C 60 C Straighten drain hose and make sure washer is not sitting on it Top of drain outlet should be less than 8 ft 2 5 m above floor 17 suoyonysuy ajes B 3 A S S D 2 q e 3 A S Q S 7 sdij Burjooisa qnoa yioddngs Safety Instructions o S S D 3 e S i u S E Troubleshooting Tips Consumer Support Before you call for service Q Troubleshooting Tips OPERATION POSSIBLE CAUSES WHAT TO DO Washer pauses in cycle washer normally pauses between washing steps Washer won operate Washer is unplugged Make sure cord is plugged securely into a working outlet Water supply is turned off Turn both hotand cold faucets fully on Controls are not set properly Make sure all selections have been made Lid is open Close lid and press START PAUSE Circuit breaker fuse is Check house circuit breakers fuses Replace fuses or tripped blown reset breaker Washer should have separate outlet Washer has not been Press the ON OFF button turned on PERFORMANCE POSSIBLE CAUSES WHAT TO DO Colored spo
12. asher GSLS1100 GSLP1100 PLUMBING WATER PRESSURE Must be 10 p s i minimum to 150 p s i maximum dynamic pressure measured at faucet WATER TEMPERATURE Household water heater should be set to deliver water at 120 to 150 F 50 to 66 C IN THE WASHER when HOT wash is selected SHUT OFF VALVES Both hot and cold shut off valves faucets should be supplied DRAIN Water may be drained into standpipe or set tub The discharge height MUST NOT BE LESS THAN 30 nor more than 8 above the base of the washer The standpipe must be 17 minimum inside diameter and must be open to the atmosphere RACK INSTALLATION Ensure washer is centered between the rack sides ELECTRICAL This appliance must be supplied with the voltage and frequency indicated on the rating plate located on the back of the washer and connected to an individual properly grounded branch circuit protected by a 15 or 20 amp circuit breaker or time delay fuse If the washer is plugged into the dryer s 115 volt outlet then the dryer needs to be on a dedicated circuit TOOLS REQUIRED Pliers Installation Instructions A CAUTION Before plugging in washer read the following electrical requirements ELECTRICAL REQUIREMENTS A CAUTION For personal safety do not use an extension cord or adapter plug with this appliance Do not under any circumstances cut or remove the third grounding prong from the power cord Follow National
13. ation problem contact your for other than the intended purpose or used dealer or installer You are responsible for providing commercially adequate electrical exhausting and other connecting B Damage to product caused by accident fire floods or facilities acts of God WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES Warrantor CAMCO INC 21 suoianijsu ajes e LI 9 A S Q S X a E E 3 A S Q S sdij Burjootsa qnoa lt 1 Consumer Support for customers in Canada www geappliancescanada com Questions Ifyou have any questions about your appliance write to Manager Consumer Relations Camco Inc 1 Factory Lane Suite 310 Moncton N B E1C 9M3 Or call 1 800 361 3400 Safety Instructions EH In Home Repair Service 1 800 361 3400 Expert repair service is only a phone call away Service Contracts 1 800 461 3636 Purchase a Camco service contract while your warranty is still in effect and you ll receive a substantial discount Camco will still be there after your warranty expires Operating Instructions Parts and Accessories Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes VISA MasterCard and Discover cards are accepted Instructions contained in this manual cover procedures to be performed by any user Other servicing ge
14. bleach dispenser Before starting the washer pour measured amount of bleach directly into bleach dispenser Avoid splashing or over filling dispenser If you prefer to use powdered bleach add it into the wash basket with your detergent W Do not mix chlorine bleach with ammonia or acids such as vinegar and or rust remover Mixing can produce a toxic gas which may cause death About the control and indicator settings www geappliancescanada com CLOTHES CARE CYCLE SOINS DES TISSUS E e PRESOAK COLOURS HOT COLD REMAINING PRETREMPAGE EXTRALARGE coycurs cHaun rRow NoRMAL LARGE WHITES WaRM warm BINSE BLANCS TIEDE TIEDE DELICATES WARM COLD RINCAGESEUL MEDIUM lt MIN e SPIN ONLY e SMALL e QUICK WASH e COLD COLD TEMPS RESTANT ESSORAGE SEUL 99 PETITE LAVAGE RAPIDE 9 FROID FROID LOAD SENSING WASH CAPTEUR DE CHARGE START OPTIONS TEMP DEPART WASH LAVAGE TOAD SIZE CYCLE PAUSE LAVAGE LAVAGE RIN AGE suoyanysuy Ajajeg Before starting the washer Load the laundry in the washer Add the detergent and fabric softener to the dispenser drawer Add bleach if needed to the bleach dispenser To Use Automatic One Touch Washing The LOAD SENSING feature automatically senses the size of your load fills with the appropriate amount of water and calculates the amount of wash time required to complete the cycle START DEPART PAUSE NO
15. imited warranty you will be responsible for any labor or in home service costs original purchase What Is Not Covered for customers in the United States Service trips to your home to teach you how to use E Replacement of house fuses or resetting of circuit the product breakers E Improper installation E Damage to the product caused by accident fire floods or E Failure of the product if it is abused misused or used for acts of God other than the intended purpose or used commercially E Incidental or consequential damage caused by possible defects with this appliance This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA In Alaska the warranty excludes the cost of shipping or service calls to your home Some states do not allow the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state To know what your legal rights are consult your local or state consumer affairs office or your state s Attorney General Warrantor General Electric Company Louisville KY 40225 What Is Not Covered for customers in Canada E Service trips to your home to teach you how to use E Replacement of house fuses or resetting of circuit the product breakers E Improper installation Bi Failure of the product if it is misused or used If you have an install
16. nerally should be referred to qualified service personnel Caution must be exercised since improper servicing may cause unsafe operation Installation Instructions Please consult your yellow pages for your local Camco number Service Satisfaction If you are not satisfied with the service you received First contact the people who serviced your appliance Next if you are still not pleased write all the details including your phone number to Director Consumer Relations Camco Inc 1 Factory Lane Suite 310 Moncton N B ELC 9M3 Troubleshooting Tips S gt e a S Printed in Korea
17. ogen gas may be produced in a water heater that has not been used for two weeks or more Hydrogen gas can be explosive under these circumstances If the hot water has not been used for two weeks or more prevent the possibility of damage or injury by turning on all hot water faucets and allowing them to run for several minutes Do this before using any electrical appliance which is connected to the hot water system This simple procedure will allow any built up hydrogen gas to escape Since the gas is flammable do not smoke or use an open flame or appliance during this process PROPER INSTALLATION This washer must be properly installed and located in accordance with the Installation Instructions before it is used If you did not receive an Installation Instructions sheet you can receive one by calling toll free in the United States the GE Answer Center 800 626 2000 In Canada call 1 800 361 3400 E Install or store where it will not be exposed to B Properly ground washer to conform with all temperatures below freezing or exposed to the governing codes and ordinances Follow details in weather Installation Instructions YOUR LAUNDRY AREA E Keep the area underneath and around your E Close supervision is necessary if this appliance is appliances free of combustible materials such as used by or near children Do not allow children to lint paper rags chemicals etc play on with or inside this or any other appliance
18. pecial instructions Lc S S E E S p BLEACH LABELS Troubleshooting Tips Consumer Support Bleach symbols Any bleach when needed Only non chlorine bleach Do not bleach when needed Installation Instructions BEFORE YOU BEGIN Read these instructions completely and carefully IMPORTANT Save these instructions for local inspector s use IMPORTANT Observe all governing codes and ordinances Note to Installer Be sure to leave these instructions with the Consumer Note to Consumer Keep these instructions for future reference Skill level Installation of this appliance requires basic mechanical skills Completion time 1 hour Proper installation is the responsibility of the installer Product failure due to improper installation is not covered under the Warranty Note This appliance must be properly grounded and electrical service to the washer must conform with local codes and ordinances and the latest edition of the National Electrical Code ANSI NFPA 70 WASHER LOCATION Washer must be installed on firm flooring to minimize vibration during spin cycles Concrete flooring is best but wood base is sufficient providing floor support meets FHA standards Washer should not be installed on rugs or exposed to the weather Install or store where it will not be exposed to temperatures below freezing or exposed to the weather W
19. pened with liquid store the washer where it will be exposed to the detergent then rinse Do not use harsh weather For information on how to keep the tub or gritty cleaners stationary when moving the washer call 1 800 361 Fill Hoses Hoses connecting washer to faucet should 3808 be replaced every 5 years Long Vacations Be sure water supply is shut offat Exterior Immediately wipe spills Wipe with faucets Drain all water from hoses if weather will i y wip EA be below freezing damp cloth Try not to hit surface with sharp objects suon nysuj Ajajeg e E m 3 A S Q E S 77 A D a Q 3 A S Q S 77 sdij Burjooisa qnoa yoddng Loading and using the washer Fabric Care Labels Below are fabric care label symbols that affect the clothing you will be laundering ee Normal Gentle delicate Safety Instructions WASH LABELS Machine wash cycle Permanent Press Do not wash wrinkle resistant Hand wash Do not wring Water temperature Hot 50 C 120 F Cold cool Warm 40 C 105 F 30 C 85 F DRY LABELS Operating Instructions Tumble dry me used with do not wash Gentle delicate Normal Permanent Press wrinkle resistant oe No heat air Line dry Drip dry Dry flat In the shade hang to dry Do not tumble dry Heat setting Medium ow S
20. per ground exists before use TO DISCONNECT THE WASHER 1 TURN WATER FAUCETS OFF UNPLUG POWER CORD AND RETURN IT TO THE STORAGE AREA DISCONNECT THE DRAIN AND WATER SUPPLY HOSES Hang them on the storage rack 15 Safety Instructions o S S S Q m S S 8 S E Troubleshooting Tips ru T gt P T M Consumer Support Before you call for service Troubleshooting Tips Save time and money Review the charts on the following pages first and you may not need to call for service Status Indicators WB Press ON OFF to turn off the washer B Call for service When the cycle has started but water has not filled the wash basket within 60 minutes a signal will sound and this code will be displayed B Make sure the incoming water faucets are on Make sure the fill hoses are not clogged or kinked Power did not automatically turn off at the end of the cycle W Press ON OFF to turn off the washer Water is not draining out of the washer B Make sure the drain hose is not kinked and is connected properly Wash load is unbalanced B Distribute laundry evenly in the basket Make sure washer is level See Leveling the Washer Washer lid is not closed B Close lid Any time the total time required is more than 99 minutes this status indicator will be displayed WATER Too many suds
21. r has missing or broken parts including a damaged cord or plug www geappliancescanada com WHEN NOT IN USE suoi anijsu Ajajeg gt B Turn off water faucets to relieve pressure on E Do not attempt to repair or replace any part of hoses and valves and to minimize leakage if a this appliance unless specifically recommended break or rupture should occur Check the in this Owner s Manual or in published user condition of the fill hoses they may need repair instructions that you understand and replacement after 5 years have the skills to carry out W Before discarding a washer or removing it E Do not tamper with controls from service remove the washer lid to prevent children from hiding inside Vl i 7 READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY o NS SAVE THESE INSTRUCTIONS Q s 3 3 A S Q S 77 A 2 e 3 S Q S o0 sdij Burjooisa qnoa yoddng Safety Instructions Operating Instructions Lc S S E E S p Troubleshooting Tips Consumer Support Special washer features Maximum Fill Tower Before starting the washer Load the laundry in the washer Add the detergent and fabric softener to the dispenser drawer Add bleach ifneeded to the bleach dispenser Detergent and Fabric Softener Dispenser Drawer The detergent and fabric softener di
22. se the hose connector provided with the washer for a one faucet connection TO CONNECT THE WASHER REMOVE THE UNI COUPLE HOSE FROM INSIDE THE WASHER BASKET Drain Connection gre Connector COLD Water Supply Connector Water Filter Uni Couple Hose CONNECT TO WATER LINE Attach the hose connector to the faucet adapter by pulling down on the locking collar while lifting up on the connector until it snaps into place Make sure the water filter provided is in place Locking Collar Hose Connector CONNECT TO VALVE INLET Attach the COLD water supply connector to the COLD water valve inlet color BLUE Make sure the washer is inside the connector before tightening TIGHTEN CONNECTOR Tighten the connector ensuring the threads are aligned properly for tightest fit Inspect for kinks or binding of the hose NOTE Do notremove the plastic cap from the HOT water inlet for uni couple connections as leakage may CONNECT DRAIN HOSE Attach the drain hose to the rear of the washer Install the clamp on the drain hose and tighten to prevent leakage of water 13 Installation Instructions WASHER CONNECTIONS FOR PORTABLE MODEL GSLP1100 ONE FAUCET CONNECTIONS CONT MAKE SURE THE TEMPERATURE TO DISCONNECT THE WASHER SELECTOR IS SET AT COLD COLD TURN WATER FAUCET OFF SLOWLY TURN ON THE WATER FAUCET ALL THE WAY TO THE D
23. sides of the washer MAKE SURE THE WASHER IS IN ITS FINAL LOCATION PULL OUT THE LEVELING LOCKS This releases the spring loaded leveling feet The washer will automatically level itself 3 PUSH THE LEVELING LOCKS BACK IN Nes Do not kick or step on the leveling locks Installation Instructions WASHER CONNECTIONS FOR STATIONARY MODEL GSLS1100 A WARNING Make sure the washer is unplugged FLUSH WATER LINES CONNECT DRAIN HOSE Run some water from the hot and cold faucets to flush Forma U shape on the end of the drain hose with the the water lines and remove particles that might clog up hose pointed toward the drain Place the hose ina the water valve screens laundry tub or stand pipe and secure it with a cable tie not included NOTE If the drain hose is placed in a stand pipe without forming a U shape a siphoning action could occur There must be an air gap around the drain hose A snug hose fit can also cause a siphoning action Cable Tie CONNECT TO WATER LINES Connect the inlet hose ends to the HOT and COLD water faucets tightly by hand then tighten another turn with pliers Turn the water on and check for leaks Lind Tub vy Ss CAREFULLY MOVE THE WASHER n Cable Tie TO ITS FINAL LOCATION 7 Stand Pipe 17 Installation Instructions WASHER CONNECTIONS FOR STATIONARY MODEL GSLS1100 CONT
24. spensers will automatically release their contents at the proper time during the cycle To Use the Detergent Dispenser Add measured detergent to the dispenser Make sure detergent is spread evenly and is level To Use the Fabric Softener Dispenser Use only liquid fabric softener Pour into dispenser using amount recommended on package W Do not fill any higher than the top of the maximum fill tower W Never pour fabric softener directly on clothes It may stain them Cleaning the Detergent and Fabric Softener Dispenser Drawer Remove the drawer by opening it fully then tilting the front of the door down Pull out Rinse the drawer with water If necessary use a soft cloth to wipe off any debris ne up the drawer with the opening an Line up the dr ith the opening and push the dispenser drawer straight in Lint Filters Clean the lint filters inside the walls of the wash basket once a week for best filtering results To remove Press the tabat the top ofthe filter and pull out To clean Open the filter Clean the filter with a toothbrush Liquid Bleach Dispenser The dispenser dilutes liquid chlorine bleach before it reaches into your wash load Check clothing care labels for special instructions Measure liquid bleach carefully following instructions on the bottle W Never pour undiluted liquid chlorine bleach directly onto clothes or into the wash basket W Do not pour powdered bleach into
25. ts Incorrect use of fabric Check fabric softener package for instructions and softener follow directions for using dispenser Pretreat stain and rewash Dye transfer e Sort whites or lightly colored items from dark colors Grayed or yellowed Not enough detergent Use more detergent especially with larger loads Hard water Use a water conditioner like Calgon brand or install a water softener Water is not hot enough Make sure water heater is delivering water at 120 F 140 F 48 C 60 C Washer is overloaded Select load size to match clothes load Dye transfer Sort clothes by color If fabric label states wash separately unstable dyes may be indicated Lint or residue on Clothes are air or line dried If you do not dry your clothes with a clothes dryer clothes your clothes may retain more lint Incorrect sorting Separate lint producers from lint collectors Washing too long Wash small loads for a shorter time than larger loads Overloading Load clothes no higher than the top row of holes in the washer tub Make sure load size selector matches clothes load size Incorrect use of fabric softener Check fabric softener package for instructions and follow directions for using dispenser Pilling Result of normal wear on While this is not caused by the washer you can slow the poly cotton blends and pilling process by washing garments inside out fuzzy fabrics 18 PERFORMANCE cont d Snags holes tears
26. www geappliancescanada com Safety Information 2 3 Owner s Manual amp Installation Instructions Operating Instructions Control and Indicator Settings 5 6 GSLS1100 Loading and Using the Washer 7 8 GSLP1100 Special Washer Features 4 Installation Instructions Alcove or Closet Installation 12 Electrical Requirements 10 Grounding Instructions 10 Installation Requirements 9 Leveling the Washer 10 Washer Connections for Portable Model GSLP1100 13 15 Washer Connections for Stationary Model GSLS1100 11 12 Troubleshooting Tips Before You Call For Service 16 19 Status Indicators 16 Consumer Support Consumer Support Back Cover Warranty saci ae abe Ki dele Fe 21 Write the model and serial numbers here Washers You can find them on a label on the back of the washer DC68 01085A 175D1807P340 49 90079 11 00 JR Safety Instructions Operating Instructions S S S Troubleshooting Tips Consumer Support IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING A WA R N I N G For your safety the information in this manual must be followed to minimize the risk of fire or explosion electric shock or to prevent property damage personal injury or loss of life RN Wi WATER HEATER SAFETY gt Under certain conditions hydr
Download Pdf Manuals
Related Search