Samsung AW12PKHBC/XAP User Manual
Contents
1. on the remote control or Press the button on the unit Result Each time you press a button the unit beeps The Z indicator end Fl will be displayed The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time The air conditioner will be contrllled as illustration below Cooling When the temperature has been increased by 1 C After 1 hour it is maintained for 7 hours To Cancel the Sleep Timer To cancel the timer press on the remote control o on the unit Result The unit beeps e The 3 indicator is no longer displayed The air conditioner operates in the mode selected last gt If you select the Energy Saving mode in the Sleep Timer mode the Sleep Timer will be cancelled Selecting Energy Saving Mode If you wish to save Energy when using your air conditioner select the Energy Saving Mode with the Energy Saver button Remote Control Control Panel 1 To select the Energy Saving mode press the Energy saver button on the remote control or unit one or more times until the Energy Saver indicator lights up ENGLISH Result The fan and compressor cycle on and off together The fan will continue to run for a short time after the compressor cycles off gt If you would like the air conditioner to run in Fan mode do not press the Energy Saver button You cannot use the Fan mode in the Energy saving mode 2 To stop the E2. screw or similar method Before installation be sure to check the installation area or the air conditioner and drain hose Checkpoints prior to installation 1 Check the cabinet and front grille of the unit for any harmful defects such as scratches 2 Be sure to check the power supply Refer to the specifications on the label attached to the unit Installation Conditions 1 As the unit is heavy the wall or window of the installation area should have sufficient strength and durability for operation of the air conditioner and for prevention of any vibration or noise If it is weak reinforcement work should be performed separately 2 Itis advisable to install the air conditioner in the north or west side to prevent the effect of direct sunlight When installing it in the south or east side due to unavoidable circumstances it is advisable to install the sunshade to prevent the direct sunlight In this case take care not to cause any hindrance to the flow of outside air 3 When installing the air conditioner be sure to obtain sufficient space on the rear side of the unit for smooth flow of air When operating the air conditioner in closed areas such as inner building with cooling operation and result in trouble with the unit See the illustration below Som Model A AWO8 145 AW12 170 AW14 AW18 AW24 gt Fence wall or other obstacle 7
3. unit button 4 Check that the air conditioner has been switched on if necessary press b On Off on the remote control or unit The timer is not correctly triggered Check that the timer has been programmed correctly see page 11 13 Odours are permeated in the room during air conditioning Air the room Technical Specifications Design and specifications are subject to change without notice Model Power Supply SERRE AA 115V 60Hz eK BABB BCIBD BE BF 220V 230V 60Hz Installation for 60Hz Electrical Requirements For personal safety This appliance must be properly grounded Do not under any circumstances cut or remove the third grounding prong from the power cord We recommend that you do not use an extension cord or an adapter plug with this appliance Do not change the plug on the power cord of this appliance Follow national electrical codes or local codes and ordinances 115V 230V 208V 230V 208V 230V 208V 15 AMP circuit 20 AMP circuit 15 AMP circuit 30 AMP circuit parallell type perpendicular type tandem type tandem type BD M 0 0 If the electric supply provided does not meet the above specifications call a licensed electrician Aluminum house wiring may pose special problems Consult a qualified electrician This unit requires a separate circuit serving only this appliance ENGLISH Installation 4 The appliance must be fixed well by
4. 50mm 150mm min 4 If the wall is greater than 150mm thick cut the wall back on a 45 angle if possible Outdoor side 45 45 xg Ee EU EE Indoor side 100mm or more In some region drain tube and drain pan may not be supplied Please contact the sales agent Installation of the Drain Tube Fix the drain tube as shown in the figure Screws 2EA Installation of the Drain Pan The procedure for installing the drain pan should be determined by the condition of the installing area Inthe case of an area where the drain pan can not be directly installed on the rear side of the unit after installing the air conditioner Example High storage 1 Open the front grille refer to page 16 2 Remove the screw located at the lower section of the front grille It is secured in the gt section depending on the model 3 Remove the front panel QUT 3 1 Press both sides of the cabinet in the direction of the arrow as A shown in the figure E 3 2 Pull the lower part of the front panel slightly forward FI zal Below three inches 3 3 Lift the front panel upward ag Applying excesive force to remove the font panel may cause damage to the tab be sure not to use excesive force 4 Remove two screws on the lower right and left sides of the unit 5 Remove the chassis from the cabinet 6 Remove the rubber cap inserted into the basepan 7 Fix the drain pan as show
5. Common Problems Before contacting the after sales service perform the following simple checks They may save you the time and expense of an unnecesary service call Problem Explanation Solution The air conditioner does not operate at all Check that the circuit breaker used for the air conditioner has not been triggered Check that the power cable is plugged into a wall socket and the socket is switched on if necessary Check that the operating mode indicator COOL or FAN on the unit is lit up if necessary press b On Off on the remote control or unit The air conditioner does not operate with the remote control 4 Check that there are no obstacles between you and the unit Replace the remote control batteries if necessary Check that you are close enough to the unit seven metres yards or less No beep is heard when you press Q On Off on the remote control Check that you are pointing the remote control at the remote control sensor on the unit Replace the remote control batteries if necessary The air conditioner does not cool Check that the correct operating mode has been selected COOL The room temperature may be too low Dust may be blocking the air filter refer to page 15 for cleaning instructions 4 Check that there is no obstacle blocking the air flow into or out of the unit The air flow direction does not change when you press the or on the
6. OWNERS INSTRUCTIONS MANUAL DE INSTRUCCIONES AWO8PKHAA AW12PKHBA BC AW14PKHBA AW18PKHBC BD AW24PKHBE BF Window type Room Air Conditioner Cool Acondicionador de aire dom stico de tipo ventana Refrigeraci n 1 O DB98 21235A 2 Safety Precautions The following safety precautions must be taken when using your air conditioner JAN WARNING Risk of electric shock Can cause injury or death Disconnect all remote electric power supplies before servicing installing or cleaning This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard DURING OPERATION DISPOSING OF THE UNIT OTHERS Users of this product are cautioned not to attempt repair of this product at their own discretion Instead they are requested to directly contact a designated service center or the outlet at which the product was purchased Never spill any kind of liquid into the unit Should this happen unplug or main switch off the unit and contact an authorized service center Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury Keep children away from the unit Do not place any obstacles in fornt of the unit Do not spray liquid of any kind into the indoor unit Should this happen switch off the breaker used for your air conditioner and contact your installation specialist Make sure that the unit is correctly v
7. ature is not displayed in this case you do not need to set the temperature 4 Toset the fan speed to Then Press the or button on the remote control as desired or Press the button on the unit one or more times until the desired fan speed F1 F2 or F3 is displayed F Low Speed F 7 Med Speed F3 High Speed 5 To control the direction of the air flow refer to page 11 Removing Excess Humidity If the atmosphere in your room is very humid or damp you can remove excess humidity without lowering the room temperature Remote Control Control Panel too much Power 9 O 1 Ifnecesary press the On Off button Result The air conditioner starts up in the cool mode The unit beeps The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 If the temperature is not displayed at the top of the control panel press the button on the control panel one or more times until it appears Result The unit beeps each time you press the button The air conditioner runs in Dry mode gt You can change modes at any time 3 To adjust the temperature press the _A_ or _V_ buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Eac
8. de sss 15 RECOMMENDATIONS FOR USE Temperature and Humidity Ranges 15 Cleaning Your Air Conditioner 16 Solving Common Problems mtem mercem tna HEEL eno 17 Technical Specifications eee ctn rrr nire i Ri Doku 18 A A Mee E ERE ED EIIETRIRENESURUTIEEESIMa TET 19 CAUTION The high inrush current of the starting compressor motor can have adverse effects to the operation of other equipment under unfavorable mains conditions This equipment does not comply with the relevant technical standards for the limitation of voltage fluctuations and flicker Before connecting this equipment to the power supply system please report to your supply authority and obtain the consent Do not connect other electric appliances to the same supply lines AW18xXxX The maximum permissible system impedance at the power junction box is 0 24 ohms Usually the maximum permissible mains impedance will not be exceeded when the branch to the power outlet is fed from a junction box with a rated current of 32A ENGLISH Air Conditioning Unit Main Parts Buttons and Display K The design and shape are subject to change according to the model Air outlet Al Inner air flow blades right left orientation ir inlet insi Outer air flow blades ad gt up down orientation The air filter is SSS located inside Air inlet Outside Ventilation lever The power plug ma
9. e selected temperature 4 To set the fan speed to Then Press the ped or Ko button on the remote control as desired or Press the button on the unit one or more times until the desired fan speed F1 F2 or F3 is displayed F i Low Speed F 2 Med Speed Fa High Speed 5 To control the direction of the air flow refer to page 10 Airing your room If the atmosphere in your room is stale you can air it using the Fan feature and if necessary evacuate the stale air outside 1 If you wish to evacuate stale air outside push the ventilation lever on the front of the unit to the right and the open position 3 amp 7 ENGLISH Result The air inside the room circulates and stale air is evacuated outside Otherwise push the ventilation lever to the left and the closed position E Result The air simply circulates inside the room Remote Control Control Panel Power 2 If necessary press the 5 On Off button Result The air conditioner starts up in the Cool mode 9 Q The unit beeps twice 3 Ifthe FAN indicator is not lit up on the unit Press the button on the remote control or Press the button on the unit one or more times until the FAN indicator lights up Result The unit beeps each time you press the button The air conditioner starts up in Cool mode gt You can change modes at any time When the air conditioner is in the Fan mode the temper
10. entilated at all times Do not place clothing or other materials over it Ifthe wireless remote control will not be used for a long time remove the batteries If applicable When using a wireless remote control the distance should not be more than 7 meters from the air conditioner If applicable The air conditioner must be plugged into its own specific power source which must be installed in compliance with national wiring earthing and safety regulations If the power cord is damaged in any way it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard This device must be installed according to the national electrical rules The appliance must be installed where the plug should be easily accesible after installation If the fuse on PC board is broken please change it with the type of T3 15a 250V The breaker of the air conditioner should be all pole switch and the distance between its two contacts should be no less than 3 5 mm Such means for disconnection must be incorporation in the fixed wiring Before throwing out the device it is necessary to pull back the battery cells and get rid of them safely for recycling reasons When you need to dispose of the unit consult your dealer If pipes are removed incorrectly refrigerant may blow out and come into contact with your skin causing injury Releasing refrigerant into the atmosphere also damages the environmen
11. h time you press the _A_ or v buttons The temperature is adjusted by 1 C The unit beeps The air conditioner starts removing the excess humidity the quantity of air is adjusted automatically 5 To control the direction of the air flow refer to page 11 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room you can adjust the orientation of the inner air flow blades on the right hand side of the unit thus increasing the efficiency of the air conditioner Remote Control Control Panel ENGLISH 1 Press the or Swng on the unit button on the remote control Result The inner blades swing automatically left and right gt In the Energy Saving Mode the blades may stop when the compressor is off For details on the Energy Saving Mode refer to page 14 2 To stop the blades moving left and right press the or on the unit button on the remote control gt To stop the blades in a specific position and orient the air flow in the corresponding direction simply press the or on the unit button on the remote control when the blades are in the desired position Adjusting the Air Flow Direction Vertically Again depending on the position of the unit in your room you can adjust the orientation of the outer air flow blades on the right hand side of te unit RECOMMENDATION When Adjust the blades to face Cooling Upwards Adjust the a
12. he air conditioner automatically after a given period of time You can set the period of time from 1 hour to 24 hours You can select the Off Timer only when the air conditioner is on Remote Control Control Panel Power 1 Check that the air conditioner has been switched on if necessary 9 press the l On Off button 2 Set the operating time by pressing on the remote control or on the unit one or more times Possible times are between 1 hour and 24 hour inclusive Result 4 The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time The air conditioner switches off automatically when the operating time reaches zero gt You can change the fan speed and air flow direction after setting the Off Timer To Cancel the Off Timer To cancel the Off Timer press on the remote control or Timer on the unit one or more times until P BR is displayed The air conditioner operates in the Cool mode or 5 on the remote control or unit button on the unit button on the remote control ENGLISH Setting the Sleep Timer The Sleep Timer can be used when you are cooling you room to switch the air conditioner off automatically after a period of 8 hours gt If you wish to switch the unit off at a specific time refer to page 12 Remote Control Control Panel Power 9 Q 1 Make sure that you have selected either cool mode 9 2 Press the button
13. ir flow blades to the desired position by pushing them upwards or downwards gt If you orient the air flow blades downwards and the unit operates in Cool mode for a long period of time dew may Form on the surface of the blades Drip from the blades Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time You can set the period of time from 1 hour to 24 hours You can select the On Timer only when the air conditioner is off Remote Control Control Panel Power 1 Check that the air conditioner has been switched off if necessary a press the l On Off button 2 Set the operating time by pressing on the remote control or on the unit one or more times Possible time is between 1 hour and 24 hours inclusive Result The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time The air conditioner switches on automatically when the operating time reaches zero gt You can change the fan speed after setting the On Timer To Cancel the On Timer To cancel the on timer press E on the remote control or on the unit one or more times until E is displayed The air conditioner operates in the Cool mode or On Off button on the remote control or unit Button on the unit Button on the remote control Setting the Off Timer The Off Timer enables you to switch off t
14. main parts buttons and display Remote control buttons They will help you find the buttons and understand the symbols displayed In the manual you will find a series of step by step procedures for each function available The ilustrations in the step by step procedures use four different symbols Moreover applicable wherever the illustrations show the positions of the buttons on both the remote control and the unit itself For the The illustrations have a Remote control Gray background Example Unit itself White background gt E Inserting the Remote Control Batteries You must insert or replace the remote control batteries when ENGLISH You purchase the air conditioner The remote control does not work correctly y Use two AAA LRO3 1 5 V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it 2 Insert the two batteries taking care to respect the polarities on the battery with on the remote control onthe battery with on the remote control 3 Close the cover by sliding it back until it clicks into place Result You can control all the functions on your air conditioning unit directly from your seat using the rem
15. n in the figure and then connect the drain hose You can use any commercialy available drain hose 8 Install the cabinet at the specified area after installing the drain pan and then re assemble it in the original condition Drain Pan gt Secure the front panel to the case by replacing the screw removed in step 2 If a screw not removed in step 2 secure the panel with a supplied screw Ty see Cap Screw Drain Hose Bottom Side View with Inthe case of an area where the drain pan can be directly E Drain Pan and Hose in Place installed on the rear side of the unit after installing the air conditioner 1 Follow steps 6 and 7 only eo
16. nergy Saving mode press the Energy Saver button on the remote control or unit again Result The fan runs at all times while the compressor cycles on and off gt If you select the Sleep Timer in the Energy Saving mode the Energy Saving will be cancelled and the air conditioner will start up in the Sleep Timer mode Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used Mode Indoor Temperature Outdoor Temperature Indoor Humidity Cooling 21 C to 32 C approx 21 C to 43 C approx 80 or less If the air conditioner is used at Then Higher temperatures The automatic protection feature may be triggered and the air conditioner stopped Lower temperatures A water leakage or some other malfunction may happen if the heat exchanger freezes Higher humidity levels Water may condense on and drip from the surface of the unit if it is used for long periods Cleaning your Air Conditioner IGIGIEKPH 23K models Front Grille gt Grille groove Body guide The air conditioner has two or three grille grooves depending on the model Be sure to clean the air filter periodically to maintain the air conditioner in the best condition for a long period of time PORTANT When cleaning the air conditioner turn it off and pull out the power plug 1 Hold the front grille handle sligh
17. ote control Cooling your room Remote Control 9 Control Panel Power You must select the Cool mode if you wish to lower the temperature in your room You can also set the fan speed 1 If necessary press the b On Off button Result The air conditioner starts up in the COOL mode 4 The unit beeps twice E The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up automatically after about three minutes 2 If the COOL indicator is not lit up on the unit Press the button on the remote control or Press the button on the unit one or more times until the COOL indicator lights up Result 4 The unit beeps each time you press the button The air conditioner starts up in Cool mode gt You can change modes at any time 3 To adjust the temperature press the LD or SY button on the remote control one or more times until the required temperature is displayed To adjust the temperature press the C2 or CvJ button on the unit one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press the temperature buttons The temperature is adjusted by 1 C and displayed on the control panel Theunit beeps The air conditioner starts cooling if the room temperature is higher than th
18. tly pull it to the left side and open the font grille gt The removal of the font grille makes it easier to clean the air conditioner Open the grille as much as possible CAUTION Removal and Reassembly of the Front Grille For user s safety a safety clip has been installed in the front grille 1 Grasp the lower part of the front grille and the front grille handle then open the grille The open angle of front grille has not to be exceeded 25 degree Lift the front grille slightly and remove it from the front panel Reassembling of front grille should be done in reverse order of disassembly 2 Pull the air filter to the right side 3 Remove all dust on the air filter with a vacuum cleaner or brush 4 When you have finished insert the air filter back into its original position 5 Wipe the surface of the unit with a neutral detergent and then wipe it again with dry cloth Be sure not to use benzene solvent or other chemical products If you Then gt Will not be using the Set the fan going for a few hours to air conditioner for a dry the inside of the air conditioner long period of time troroughly 4 Switch the air conditioner off and unplug it from the wall socket 4 Clean the filter and outer surfaces J gt Have not used the air conditioner for a long period of time Set the fan going for a few hours to dry the inside of the air conditioner troroughly Sol g
19. ts Please recycle or dispose of the packaging material for this product in an environmentally responsible manner Never store or ship the air conditioner upside down or sideways to avoid damage to the compressor The appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency Contents PREPARING YOUR AIR CONDITIONER Safety PRECAUTIONS ine eee eer ete Deed Re E ie RE e DE ede 2 Air Conditioning Unit Main Parts Buttons and Display ssssssssss 4 Remote Control Buttons 5 Getting Started 6 Inserting the Remote Control Batteries sseseessseeen eene 7 OPERATING YOUR AIR CONDITIONER amp Cooling Your ROOIn ttm tr meet i eene trn 8 a Airing Your Room 9 Removing Excess Humidity e 10 Adjusting the Air Flow Direction Horizontally sssssee 11 a Adjusting the Air Flow Direction Vertically ssssss me 11 PROGRAMMING YOUR AIR CONDITIONER Setting the OM TIGE sese san hec ae Fan hieu inv epa Setting the Off Timer Setting the Sleep Timer wo ccc ccecccssccssscsseccsessseseseeeseseseaseeeseseusenavenaeeees 14 Selecting Energy Saving mo
20. y be not s pplied depending on the model The type of the power Power plug P plug may differ accor ding to the local power supply Temperature Timer settings SSN mode indicators OOL DRY FAN Temperature adjustment Sleep Timer setting button uttons 7 Timer setting button Remote control sensor Air flow blade i swing button T 7 Air Swing Air Swing Fan speed adjustment utton Timer indicator Sleep indicator 11 Operating mode selection T button COOL DRY FAN Fan Speed E Energy Saver button ON OFF button Remote Control Buttons Timer setting button lg CAS Temperature adjustment Tre spP buttons Sleep timer setting button Fan speed adjustment buttons Operating mode selection buttons Energy Saver button Air flow blade swing button ON OFF button ENGLISH g Started You have just purchased a window type room air conditioner and it has been installed by your installation specialist Your Owner s Instructions contain valuable information on using your air conditioner Please take the time to read them as they will help you take full advantage of the unit s functions This Owner s Instructions is just for using your air conditioner correctly Thus the illustrations shown in this manual may not exactly match your air conditioners The booklet is organized as follows The following figures are shown on pages 4 and 5 Air conditioning unit
Download Pdf Manuals
Related Search