Samsung SH12BWH Manual de Usuario
Contents
1. 2 Ifthe u is not displayed at the top of the remote control press the appears Result Nota e button on the remote control one or more times until it The indoor unit beeps each time you press the r button The air conditioner runs in the Auto mode The Auto mode cools and heats the room in optimum condition by adjusting the indoor temperature depending on the set temperature The mode may change from cooling into heating from heating into cooling depending on the current temperature during operation You can change modes at any time 3 To adjust the temperature press the 7 A button one or more times until the required temperature is displayed Possible temperatures are between 16 C and 30 C inclusive Result Each time you press the Y A button The temperature is adjusted by 1 C The indoor unit beeps 0 6 Cooling Your Room You must select the Cool mode if you wish to adjust the Cooling temperature Fan speed when cooling POWER 1 If necessary press the o button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally aft2. The indoor unit beeps The air conditioner starts up in the most suitable mode for the room temperature The mode may change from cooling into heating from heating into cooling depending on the current temperature during operation Room Temperature Operating Mode Less than 24 C Heat 24 or above Cool a 1 2 To switch the air conditioner off press the On Off switch again Nowe Even if the air conditioner has been switched on via the On Off switch operations can still be controlled using the remote control as usual Solving Common Problems Before contacting the after sales service perform the following simple checks They may save you the time and expense of an unnecessary call Problem Explanation Solution The air conditioner does not operate at all Check that the breaker used for the air conditioner is switched on Check that the operation indicator on the indoor unit is on if necessary press the button on the remote control Check whether the Timer indicator on the indoor unit is switched on If so Wait until the switch on time is reached and the air conditioner starts up automatically Cancel the timer see pages 18 and 19 for further details The air conditioner does not operate with the remote control 227 Check that there are no obstacles between you and the indoor unit Check the remote control batteries Check that you are close enough to the indoor u
3. Result The outer blade is adjusted vertically t SET CANCEL a 2 If you want the blade to move up and down automatically when the air conditioner is operating press the O button Result The blade move up and down around the base position set 3 To stop the blade moving up and down press the button again Nowe fyou switch the air conditioner Then the blade is Off Closed completely On again Set to the initial position powered Adjusting the Air Flow Direction Horizontally There are two sets of inner air flow blades J ust as the outer air flow blade can be adjusted vertically the inner blades can be adjusted horizontally 1 Adjust each set of inner blades to the required position by pushing or pulling them sideways Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time You can set the period of time from 1 hour to 24 hours 1 To set the operating time press the button one or more times until the required time is displayed Possible time is between 1 hour and 24 hours inclusive SET CANCEL 2 Press the button to complete the setting Result The remaining time is displayed Blinking of the timer indicator stops The selected mode and the temperature on the display disappear after 10 seconds The air conditioner will switch on automatically when the counter displayed on the rem
4. When it has been decreased Set by 2 C after 2 hours the TEMP temperature is maintained for four hours To Cancel the Sleep Timer If you no longer wish to use the Sleep Timer that you have set you can cancel it at any time Press the e button Result The indoor unit beeps The 2 indicator is no longer displayed The air conditioner operates normally Setting the 1 Hour Timer The 1 Hour Timer enables each mode to operate only for an hour and stop automatically with just one touch of the 1 Hour Timer button It is good for you when you feel setting the Off Timer by pressing the Off Timer button several times is unnecessary and inconvenient 1 Press the e button one or more times until the indicator appears on the remote control Result The indoor unit beeps The air conditioner will stop operating after an hour automatically 2 To select an operating mode under the set 1 Hour Timer press the O button until the desired mode is displayed at the remote control Result The air conditioner will run and stop operating in the selected mode with the 1 Hour Timer set Note If you operate the 1 Hour Timer when the air conditioner is turned off the air conditioner will start operating and be turned off after an hour To cancel the 1 Hour Timer If you no longer wish to use the 1 Hour Timer that you have set you can cancel it at any time SET TEMP Press the button i Result
5. OWNER S INSTRUCTIONS Indoor unit Outdoor unit SHO9BWH SHO9BWHX SH12BWH SH12BWHX SPLIT TYPE ROOM AIR CONDITIONER Cool and Heat OR DB98 21903A 1 Register your product at www samsung com global register Safety Precautions The following safety precautions must be taken when using your air conditioner WARNING Risk of electric shock e Can cause injury or death e Disconnect all remote electric power supplies before servicing installing or cleaning This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard DURING OPERATION Users of this product are cautioned not to attempt repair of this product ETE 292 DN at their own discretion Instead they are reguested to directly contact a designated service center or the outlet at which the product was purchased Never spill any kind of liquid into the unit Should this happen unplug or main switch off the unit and contact an authorized service center Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury Keep children away from the unit Do not place any obstacles in front of the unit Do not spray liquid of any kind into the indoor unit Should this happen switch off the breaker used for your air conditioner and contact your installation specialist Make sure that the unit is correctly ventilated at all times Do not place clothing or o
6. Control Batteries You must insert or replace the remote control batteries when You purchase the air conditioner The remote control does not work correctly Note Use two AAA LR03 1 5V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it 2 Insert the two batteries taking care to respect the polarities on the battery with on the remote control on the battery with on the remote control 3 Close the cover by sliding it back until it clicks into place Selecting the Automatic Operating Mode You can start the air conditioner in Auto mode from your remote control In the Auto mode the cooling and heating operation is selected automatically You can also raise or lower the temperature and the fan speed in the Auto mode POWER 1 If necessary press the button Result PORTANT The operation indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes
7. The indoor unit beeps Tarh The indicator is no longer displayed The air conditioner operates normally Operating Recommendations Here are a few recommendations that you should follow when using your air conditioner Topic Recommendation Heating performances The heat pump inside the air conditioner absorbs heat from outside air and brings it indoors If the temperature of the outside air drops the air conditioner will heat less If you find that the room is not warm enough use an additional heating appliance Warm air circulation The air conditioner circulates warm air to heat your room as a result some time will be required after starting the air conditioner to warm the entire room If necessary set the air conditioner on before you wish to use the room Frost When outside temperatures are low and humidity is high frost may form in the outdoor unit when heating is selected If this happens The heating operation is stopped The Deice mode is triggered automatically for about seven minutes No intervention is required from you after about seven minutes the air conditioner starts operating again normally High indoor and outdoor If both the indoor and outdoor temperatures temperatures are high and you select the Heat mode the outdoor unit s fan and compressor may stop at times This is normal simply wait until the air conditioner switches on again Power failure If a power failur
8. dry them in the shade 4 Insert the filters into the original position Note You can change the position of filters with each other 5 Close the front grille THIS AIR CONDITIONER IS MANUFACTURED BY a ELECTRONICS
9. 2 hours 1 Press the button until 2 Hr is displayed 2 Press the C button 3 Press the button until 4 Hr is displayed 4 Press the button SET CANCEL Note You can see or change the setting mode and or the temperature by pressing the M2 amp button or the 7 A button after setting the Off Timer To Cancel the Off Timer If you no longer wish to use the Off Timer that you have set you can cancel it at any time SET CANCEL Press the button Note Ifyou want to turn off the air conditioner before the timer reaches the setting time press the button Setting the Sleep Timer SET CANCEL a gt ON m The Sleep Timer can be used when you are cooling or heating your room to switch the air conditioner off automatically after a period of 6 hours Note If you wish to switch the unit off at a specific time refer to page 19 1 Make sure that you have selected either the Cool or Heat mode 2 Press the button one or more times until the 2 indicator appears on the remote control Result The indoor unit beeps The air conditioner will be controlled as indicated in the illustrations below Cooling The desired temperature is increased by 1 C every hour When it has been increased by 2 C after 2 hours the Set temperature is maintained for TEMP four hours rari Stop Heating The desired temperature is decreased by 1 C every hour Start Stop
10. ING YOUR AIR CONDITIONER m Selecting the Automatic Operating Mode 9 m Cooling Your Room lt lt 10 m Heating Your Room 11 m Removing Excess Humidity c cece eee eee 12 m Airing Your Room eee 13 m Changing the Room Temperature Quickly ununun 14 m Selecting Energy Saving Mode ias 15 m Adjusting the Air Flow Direction Vertically 16 m Adjusting the Air Flow Direction Horizontally 17 PROGRAMMING YOUR AIR CONDITIONER m Setting the On Timer Ls 18 m Setting the Off Timer lt 19 m Setting the Sleep Timer aaan 20 m Setting the 1 Hour Timer ooo 21 RECOMMENDATIONS FOR USE m Operating Recommendations kis 22 m Temperature and Humidity Ranges lesse 23 m Operating Your Air Conditioner Without the Remote Control 23 m Solving Common Problems 4 24 m Cleaning Your Air Conditioner LL 25 m Cleaning Deodorizing and Bio filter Option sa auaeaaa 25 View of the Unit The design and shape are subject to change according to the model Temperature sensor On Off switch Air filter Air flow blades under the grille outlet Air Inlet Operation indicator GREEN Timer indicator GREEN RED On Off switch nit Air Inlet Rear Connection Valve 5 5 o 5 Remote Control Buttons and Display Remote control transmission indicator Temperature and Timer setting Battery life indicator 1 Hour Time
11. air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 If the is not displayed at the top of the remote control press the MODE button on the remote control one or more times until it appears 0 Result The indoor unit beeps each time you press the button The air conditioner runs in the Heat mode Note You can change modes at any time 3 To adjust the temperature press the Z A button one or more times until the required temperature is displayed Possible temperatures are between 16 C and 30 C inclusive Result Each time you press the 7 A button The temperature is adjusted by 1 C The indoor unit beeps If the room temperature reaches the set temperature selected temperature 5 C the air conditioner stops heating but the fan is still operating The air conditioner starts heating provided that the room temperature is lower than the desired temperature selected temperature 3 C 4 Select the fan speed by pressing the rj button one or more times until the required setting is displayed Hat Automatic rotated gt amp gt Buut oh Low Ba Medium Rant High FAN SPEED Result Each t
12. and in the Heat mode the temperature will fall resulting in saving energy POWER 1 If necessary press the 6 button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes ENERGY SAVING 2 Press the button Result The indoor unit beeps The air conditioner runs in the Energy Saving mode The outer air flow blade moves up and down To stop the Energy Saving mode press the EAN again Note You can select the Energy Saving mode in the Cool and Heat mode 3 To adjust the temperature press the 7 A button one or more times until the required temperature is displayed 4 To select the fan speed press the C button one or more times until the required setting is displayed 5 To control the direction of the air flow refer to pages 16 and 17 j Adjusting the Air Flow Direction Vertically Depending on the position of the indoor unit on the wall of your room you can adjust the position of the outer air flow blade on the bottom of the unit thus increasing the efficiency of the air conditioner 1 Press the el button one or more times as required
13. e occurs when the air conditioner is operating the unit is switched off When the power returns the air conditioner starts up again automatically Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used If the air conditioner is used at Then High temperatures The automatic protection feature may be triggered and the air conditioner stopped Low temperatures A water leak or some other malfunction may occur if the heat exchanger freezes High humidity levels Water may condense on and drip from the surface of the indoor unit if it is used for long periods Mode Outdoor Temperature Indoor Temperature Indoor Humidity Heating 0 C to 24 C approx 27 or less Cooling 19 C to 43 C approx 16 C to 32 C approx 80 or less Drying 19 C to 43 C approx 16 C to 32 C approx gt If the outdoor temperature is as low as 0 C the heating capacity drops up to 70 80 depending on the Operating condition If the cooling operation is used at over 32 C indoor temperature it does not cool at its full capacity Operating Your Air Conditioner Without the Remote Control Your air conditioner can be operated directly from the indoor unit if the remote control is lost or broken 1 To switch the air conditioner on press the ON OFF switch on the right side of the indoor unit Result The Operation indicator on the indoor unit comes on
14. er three minutes 2 Ifthe is not displayed at the top of the remote control press the e button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the e button The air conditioner runs in the Cool mode Note You can change modes at any time 3 To adjust the temperature press the X A button one or more times until the required temperature is displayed Possible temperatures are between 16 C and 30 C inclusive Result Each time you press the Y A button The temperature is adjusted by 1 C The indoor unit beeps The air conditioner starts cooling provided that the room temperature is higher than the selected temperature If the room temperature reaches the set temperature the air conditioner stops cooling but the fan is still operating SET TEMP 4 Select the fan speed by pressing the button one or more times 1 until the reguired setting is displayed Hat Automatic rotated amp gt K u gt Rau Low Sau Medium Baat High Result Each time you press the button the indoor unit beeps a 5 To control the direction of the air flow refer to pages 16 and 17 Heating Your Room You must select the Heat mode if you wish to adjust the Heating temperature Fan speed when heating 1 If necessary press the button Result The operation indicator on the indoor unit lights up The
15. heating function is used to cool or heat your room as quickly as possible Example You have just come home and find that the room is very hot You wish to cool it down as quickly as possible The Turbo function operates for 30 minutes with the maximum settings before retuming automatically to the mode and temperature previously selected 1 If necessary press the button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps 2 Press the button Result The temperature and fan settings are adjusted automatically The air conditioner cools or heats the room as quickly as possible After 30 minutes the air conditioner is reset automatically to the previous mode temperature and fan settings You can select the Turbo function in the Auto Cool and Heat mode If you select this function in the Dry or Fan mode it will return to the Auto mode 3 If you wish to stop the Turbo function before the end of the 30 minute period press the e button one or more times until gee disappears Result The air conditioner is reset automatically to the previous mode temperature and fan settings 4 To control the direction of the air flow refer to pages 16 and 17 Selecting Energy Saving Mode You can save energy even during operation in the Cool and Heat mode In the Cool mode the temperature will rise
16. ime you press the button the indoor unit beeps For the first three to five minutes the fan operates very slowly until the air has been sufficiently warmed Once the SET TEMP LL w correct temperature has been reached the fan is automatically set to the required speed 5 To control the direction of the air flow refer to pages 16 and 17 Removing Excess Humidity If the atmosphere in your room is very humid or damp you can remove excess humidity without lowering the room temperature too much 1 If necessary press the button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps PORTANT The air conditioner is fitted with a protection mechanism POWER to prevent the unit from being damaged when it is started i immediately after being Plugged in E Stopped It will start up normally after three minutes SET TEMP yt 2 Ifthe 4is not displayed at the top of the remote control press the MODE is O button on the remote control one or more times until it appears MODE Result The indoor unit beeps each time you press the button The air conditioner runs in the Dry mode Note You can change modes at any time saan 3 To adjust the temperature press the 7 A button one or more times 5 i until the required temperature is displayed m Possib
17. le temperatures are between 16 C and 30 C inclusive Result Each time you press the 7 A button The temperature is adjusted by 1 C The indoor unit beeps The air conditioner starts removing the excess humidity the quantity of air is adjusted automatically 4 To control the direction of the air flow refer to pages 16 and 17 Airing Your Room If the atmosphere in your room is stale you can air the room using the Fan feature 1 If necessary press the button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps 2 If the e is not displayed at the top of the remote control press the ys button on the remote control one or more times until it appears ME Result The indoor unit beeps each time you press the button The air conditioner runs in the Fan mode The temperature is set automatically Note You can change modes at any time 3 Select the fan speed by pressing the Cy button one or more times until the required setting is displayed oh Low Ru Medium Rau High FAN SPEED Result Each time you press the O button the indoor unit beeps 4 To control the direction of the air flow refer to pages 16 and 17 ee wv FAN SA GY SAVING FLAP SLEEP a Changing the Room Temperature Quickly The Turbo cooling
18. nit seven meters yards or less No beep is heard when you press the 5 on the remote control Check that you are pointing the remote control at the remote control sensor in the right of the indoor unit Replace the remote control batteries if necessary The air conditioner does not cool or heat When heating the required room temperature is never reached and the air conditioner frequently stops 99 Check that the correct operating mode has been selected Auto Cool Heat The room temperature may be too low or too high Dust may be blocking the air filter guard refer to page 25 for cleaning instructions Check that there is no obstacle in front of the outdoor unit Check that the required temperature has been set correctly Increase the fan speed If the air flow is directed upwards use the remote control to direct it downwards The fan speed does not change when you press the button Check that the operating mode is set to the Auto Cool Heat or Fan mode in the Dry mode the fan speed changes automatically The air flow direction does not change when you press the button Check that the air conditioner has been switched on if necessary press the button on the remote control The timer is not correctly triggered Check that the timer has been programmed correctly see pages 18 and 19 Odour is permeated in the room during air conditioning Air the room Cleaning Yo
19. ote control reaches the set time and disappears the On Timer setting 3 To select an operating mode in advance press the O button until the desired mode is displayed at the top of the remote control Result The air conditioner will run in the selected mode when it is turned on Note If you don t operate the remote control after setting the On Timer it will be turned off automatically after 25 hours To Cancel the On Timer If you no longer wish to use the On Timer that you have set you can cancel it at any time Note If you want to turn on the air conditioner before the timer reaches SET CANCEL Press the oe button the setting time press the O button Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given period of time You can set the period of time from 1 hour to 24 hours 1 To set the operating time press the button one or more times until the required time is displayed Possible time is between 1 hour and 24 hours inclusive SET CANCEL 2 Press the button to complete the setting Result The remaining time is displayed Blinking of the timer indicator stops The air conditioner will switch off automatically when the counter displayed on the remote control reaches the set time and disappears the Off Timer setting ample If you would like to turn the air conditioner on after 2 hours and to operate it for
20. r indicator On Timer setting Off Timer setting Operating mode 4 AUTO COOL DRY FAN XXHEAT Turbo mode Sleep mode Energy Saving Air flow direction Fan speed Turbo button On Off button D 1 Hour Timer button Mode selection button AUTO COOL DRY FAN HEAT Fan speed button Airflow control button Timer Set Cancel button Battery check button Note Each mode indicator shows each mode as well as the battery life If you want to check the battery press the C button The more is a battery life indicator the longer will remain the battery life If one battery life indicator remains replace new batteries Getting Started You have just purchased a split type air conditioner and it has been installed by your installation specialist Your Owner s Instructions contains valuable information on using your air conditioner Please take the time to read it as it will help you take full advantage of the unit s features The booklet is organized as follows The following figures are shown on pages from 4 to 6 Indoor and outdoor units Remote control buttons and display They will help you find the buttons and understand the symbols displayed Inthe manual you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use three different symbols HOLD DOWN Inserting the Remote
21. ther materials over it Ifthe wireless remote control will not be used for a long time remove the batteries If applicable When using a wireless remote control the distance should not be more than 7 meters from the air conditioner If applicable DISPOSING OF THE UNIT Before throwing out the device it is necessary to pull back the battery Se cells and get rid of them safely for recycling reasons When you need to dispose of the unit consult your dealer If pipes are removed incorrectly refrigerant may blow out and come into contact with your skin causing injury Releasing refrigerant into the atmosphere also damages the environments Please recycle or dispose of the packaging material for this product in an environmentally responsible manner OTHERS Never store or ship the air conditioner upside down or sideways to a V avoid damage to the compressor The appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency Contents PREPARING YOUR AIR CONDITIONER m Safety Precautions ennen 2 m View of the Unit Laikai 4 m Remote Control Buttons and Display esaeen 6 m Getting Started Ls 7 m Inserting the Remote Control Batteries 8 OPERAT
22. ur Air Conditioner To get the best possible use out of your air conditioner you must clean it regularly to remove the dust that accumulates on the air filter PORTANT Before cleaning your air conditioner ensure that you have switched off the breaker used for the unit 1 Open the upper front grille by pulling the lower right and left tabs of the grille 2 Pull air filters out of each tab of the grille 3 Remove all dust on the air filters with a vacuum cleaner or brush 4 When you finished insert air filters by fixing it to each tab of the grille 5 To close the front grille fix it to hooks and push down the lower right and left tabs of the grille 6 Clean the front grille with a damp cloth and mild detergent do NOT use benzene solvents or other chemicals Note If you have not used the air conditioner for a long period of time set the fan going for three to four hours to dry the inside of the air conditioner thoroughly Cleaning Deodorizing and Bio filter Option To remove minute dust particles and odors deodorizing and Bio filter are installed in the air conditioner You should clean the filters every 3 months 1 Open the upper front grille by pulling the lower right and left tabs of the grille Deodorizing Filter 2 Pull out the deodorizing and Bio filter Bio Filter 3 Wash the filters with clean water then
Download Pdf Manuals
Related Search