Samsung AR09JSPFBWKNEU Manual de Usuario
Contents
1. English 31 EU Best model_IB_DB68 05163A_EN indd 31 2015 1 9 11 38 20 Maintaining the air conditioner If the air conditioner will not be used for an extended period of time dry the air conditioner to maintain it in best condition 1 Dry the air conditioner thoroughly by operating in Fan mode for 3 to 4 hours and cut off the power supply There may be internal damage if moisture is left in components 2 Before using the air conditioner again dry the inner components of the air conditioner again by running in Fan mode for 3 to 4 hours This helps remove odors which may have generated from dampness Periodical checks Refer to the following chart to maintain the air conditioner properly Type Description pelle nn Es Once a year Clean the air filter 1 Clean the condensate drain pan 2 Indoor Thoroughly clean the heat exchanger 2 unit Clean the cross fan 2 Clean the condensate drain pipe 2 Replace the remote controller batteries 1 Clean the heat exchanger on the outside ofthe unit 2 Clean the heat exchanger on the inside of the unit 2 Clean the electric components with jets of air 2 Outdoor Verify that all the electric components are firmly e unit tightened 2 Clean the fan 2 Verify that all the fan assembly is firmly tightened 2 Clean the2. EU Best model_IB_DB68 05163A_EN indd 1 2015 1 9 11 38 05 ZS E Features of your new air conditioner 2 step cooling 2 step cooling function will quickly cool the room to reach the set temperature and then it will adjust the fan speed and air flow direction automatically to help you stay comfortable and refreshing Fast cooling heating If you want the strong and cool warm air just select Fast function It will get you the strongest air Comfort cooling heating If you want the comfortable and refreshing air Comfort function will spread the cool warm air indirectly to you so that you can stay comfortable Single User Use Single User function when you are alone at home Single User function will minimize the energy consumption with inverter technology and reduce your electricity bill by adjusting the maximum operating capacity ofthe compressor Easy Filter There is no grille to remove before separating the filter from the air conditioner Therefore filter can be cleaned easily more frequently Frequent filter cleaning will prevent dust from entering into the product or accumulating on the filter good sleepfunction good sleep function will allow you to have deep good night s sleep by adjusting the temperature fan speed and air flow direction Smart Install When the installation is done your product will examine itself through trial operation to check if it was installed proper
3. EU Best model_IB_DB68 05163A_EN indd 3 2015 1 9 11 38 06 e COMTE Safety precautions Before using your new air conditioner please read this manual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance Because the following operating instructions cover various models the characteristics of your air conditioner may differ slightly from those described in this manual If you have any questions call your nearest contact center or find help and information online at www samsung com Important safety symbols and precautions Hazards or unsafe practices that may result in severe WARNING personal injury or death Hazards or unsafe practices that may result in minor A CAUTION personal injury or property damage Follow directions Cut off the power supply Do NOT attempt Do NOT disassemble Make sure the machine is grounded to prevent electric shock FOR INSTALLATION WARNING Q Use the power line with the power specifications of the product or higher and use the power line for this appliance only In addition do not use an extension line D Extending the power line may result in electric shock or fire P Do not use an electric transformer It may result in electric shock or fire gt Ifthe voltage frequency rated current condition is different it may cause fire The installati
4. Heating 27 C or less 15 C 24 C 2 Dry 18 C 32 C 10 C 46 C s gt Ifthe air conditioner operates in cooling mode for long period of time in high humidity area dew may be formed gt If the outdoor temperature goes down to 5 C heating capacity may decrease as much as 60 70 of specified capacity according to the using conditions Model AJ gt Mode Ca Sn Indoor humidity Remark Cooling 16 C 32 C 5 C 46 C 80 or less AJ100 outdoor temperature 10 C 46 C Heating 27 Corless 15 C 24 C 2 Dry 18 C 32 C 5 C 46 C AJ100 outdoor temperature 10 C 46 C gt The standardized temperature for heating is 7 C If the outdoor temperature drops to 0 C or below the heating capacity D can be reduced depending on the temperature condition amp gt Ifthe cooling operation is used at over 32 C indoor temperature it does not cool at its full capacity Maintaining your air conditioner Internal protections via the unit control system gt This internal protection operates if an internal fault occurs in the air conditioner Type Description Against cold air The internal fan will be off to prevent cold air when the heat pump is heating The internal fan will be off to defrost ice when the heat pump is heating Defrost cycle Vertical air flow blade will be closed during defrost cycle and it will open again during heating operation after def
5. Turning the air conditioner off and then on again with the circuit breaker may cause a spark and result in electric shock or fire After unpacking the air conditioner keep all packaging materials well out of the reach of children as packaging materials can be dangerous to children Ifa child places a bag over its head it may result in suffocation English 6 EU Best model_IB_DB68 05163A_EN indd 6 2015 1 9 11 38 07 ZS EU Do not touch the air flow blade with your hands or fingers during the heating operation This may result in electric shock or burns Do not insert your fingers or foreign substances into the air inlet outlet of the air conditioner gt Take special care that children do not injure themselves by inserting their fingers into the product Do not strike or pull the air conditioner with excessive force This may result in fire injury or problems with the product NOILYHVd34d LO Do not place an object near the outdoor unit that allows children to climb onto the machine gt This may result in children seriously injuring themselves Do not use this air conditioner for long periods of time in badly ventilated locations or near infirm people Since this may be dangerous due to a lack of oxygen Open a window at least once an hour Ifany foreign substance such as water has entered the appliance cut off the power supply and contact the nearest service center gt Fa
6. condensate drain pan 2 e This check mark requires checking the indoor outdoor unit periodically Follow the description to maintain the air conditioner properly A 1 The described operations should be performed more frequently if CAUTION _ thearea of installation is very dusty 2 These operations must always be performed by qualified personnel For more detailed information see the installation part in the manual English 32 EU Best model_IB_DB68 05163A_EN indd 32 2015 1 9 11 38 20 MS CONS UE Troubleshooting Refer to the following chart if the air conditioner operates abnormally This may save time and unnecessary expenses PROBLEM SOLUTION S The air conditioner Check power status and then operate the air conditioner does not work at again z all Plug in or switch on the circuit breaker and then operate the air conditioner again Ensure Isolator is switch on Check if you have set the Off Timer Operate the air conditioner again by pressing the Power button Push down the Grille Door manually maybe the Grille Door s stepping motor has problem And Check the display if error indicator appears the air conditioner has another problem also Contact the nearest service center The temperature Check if you have selected Fan Fast mode In these modes adjustment is not set temperature is set to auto and you cannot adjust the working temperature Cool Warm air Check if the
7. consumption indicator Auto clean indicator Power button Remote controller receiver Wi Fi indicator Timer Auto clean indicator English 11 EU Best model_IB_DB68 05163A_EN indd 11 2015 1 9 11 38 08 ZS EU Checking the remote controller Point the remote controller towards the remote controller receiver of the indoor unit When you properly press the button on the remote controller you will hear beep sound from the indoor unit and a transmit indicator gt appears on the remote controller display Remote controller buttons x Before using the functions of the remote controller you should set the current time Refer to page 17 Vertical air swing Activate Deactivate vertical air flow blade movement automatically Mode amp Set one of the 5 operating modes D Power Turn on off the air conditioner Temp Fana w Increase Decrease the Adjust the fan speed temperature by 1 C Options Select options during operation Horizontal air swing Activate Deactivate horizontal air flow blades movement automatically Timer Select Timer option Settings Select settings SET Directional lt gt on the selected option or Move through the Timer 9 Options or Settings menu to make a selection In case you wish to cancel the options or settings that you have just set press the Options or Settings button again NOTE then
8. cut the power at the circuit breaker gt Failing to do so may result in electric shock or fire FOR USING WARNING Ifthe appliance is flooded please contact your nearest service center gt Failing to do so may result in electric shock or fire If the appliance generates a strange noise a burning smell or smoke cut off the power supply immediately and contact the nearest service center Failing to do so may result in electric shock or fire In the event of a gas leak such as propane gas LP gas etc ventilate immediately without touching the power line Do not touch the appliance or power line gt Do not use a ventilating fan D A spark may result in an explosion or fire To reinstall the air conditioner please contact your nearest service center gt Failing to do so may result in problems with the product water leakage electric shock or fire gt A delivery service for the product is not provided If you reinstall the product in another location additional construction expenses and an installation fee will be charged gt Especially when you wish to install the product in an unusual location such as in an industrial area or near the seaside where it is exposed to the salt in the air please contact your nearest service center Do not touch the circuit breaker with wet hands This may result in electric shock Do not turn the air conditioner off with the circuit breaker while it is operating gt
9. disappear Q Indoor unit display Setting the Display option amp Display lighting can be adjusted by following this instruction amp 1 Press the Settings button 2 Press the or Settings button until Display indicator starts to blink 3 Press the SET button to set the display status 3 seconds after setting Display function Display indicator on the remote controller display will disappear and indoor unit display will be turned off gt Press the Settings button gt Press the C or Settings button to make Display indicator blink and press the SET button gt Display indicator on the remote controller display will disappear and the indoor unit display will be turned on again Cancel Display option cannot be set when the air conditioner is off Note Ifyou turn off the display when the Virus doctor function is in operation with air conditioner operation the indoor unit display and Virus Doctor lamp will be turned off at the same time Operation or timer display will not be turned off by the display off function English 27 EU Best model_IB_DB68 05163A_EN indd 27 2015 1 9 11 38 18 BRENT CSN EU Setting the Beep sound Beep sound from the indoor unit can be muted 1 Press the Settings button 2 Press the Q or Settings button until Beep indicator starts to blink 3 Press the SET button to mute the beep sound 3seconds after setting Beep sound function Bee
10. display using alkaline detergent CAUTION Do not use sulfuric acid hydrochloric acid organic solvents such as thinner kerosene and acetone etc to clean the surface of the product or put any stickers on it They may damage the surface of the air conditioner Cleaning the outdoor unit heat exchanger gt When dust accumulates on the heat exchanger it may decrease cooling performance Therefore clean it regularly gt Spray water to clean the dust SR lt Re RER IIK PESSA RL RER RER RER RRR amp K 0 ace RO dnt ss REEL RS RRR 2 ss ER Ifit is difficult to clean the outdoor unit heat exchanger on NOTE Your own contact service center RTL ER ER RR 2 Be R TX e Be careful with the sharp edges on the Heat exchanger CAUTION outdoor unit heat exchanger Illustration may differ slightly depending on the models English 29 EU Best model_IB_DB68 05163A_EN indd 29 2015 1 9 11 38 19 ZS E Cleaning the air conditioner Removing the Air filter Air filter There is a hole on the bottom right side of the filter Put your finger in that hole to get a grip on the filter and slightly push it up to release the hooks from the bottom side Then pull it down to remove the filter from the main body Cleaning the air filter Washable foam based air
11. set temperature by 1 C within the range of 16 C 30 C Zs Press the button to set the desired fan speed Vv Auto B Auto coa Auto Low amp Med ae High amp Turbo Dry 2 Auto Fan I Low Er Med Er High Bl Turbo Heat Auto Low Med amp High Turbo B Dry mode is only available in the cooling mode NOTE English 15 EU Best model_IB_DB68 05163A_EN indd 15 2015 1 9 11 38 09 Adjusting the air flow direction This function will allow you to adjust the air flow direction vertically and or horizontally Press the or button to make air flow blades vertically and or horizontally Vertical air flow Horizontal air flow gt To keep the air flow direction in a constant direction press the or button again The air flow blade s will stop the movement gt Ifyou adjust the vertical air flow blade manually it may not close completely when you turn off the air conditioner gt Ifyou adjust the horizontal air flow blade manually it may not operate normally Adjusting the air flow direction is not note available in good sleep mode while it is in cool mode However you can adjust the air flow direction in good sleep mode while it is in heat mode Remote controller display Remote controller display English 16 EU Best model_IB_DB68 05163A_EN indd 16 2015 1 9 11 38 10 MMM a NE Setting the Current time Bef
12. signs accordingly Make sure Storing the remote controller you have inserted the batteries in correct position When you do not use the remote controller for long time 3 Close the cover by place it back to its original position remove the batteries from the remote controller and store it 3 The signal may not be received well of electronic lighting style fluorescent lamps such as inverter fluorescent lamps are in the same space Ifother electrical products operate by the remote controller call your nearest contact center Correct disposal of batteries in this product Applicable in countries with separate collection systems This marking on the battery manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life Where marked the chemical symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 If batteries are not properly disposed of these substances can cause harm to human health or the environment To protect natural resources and to promote material reuse please separate batteries from other types of waste and recycle them through your local free battery return system English 13 You should hear click sound when the cover is locked properly N NOILDNNA DISV4 ZO ZS E Basic function Basic operation is an operation mode that can b
13. the most recently selected item will blink and you may simply cancel it by pressing the SET button while selected item is blinking English 12 EU Best model_IB_DB68 05163A_EN indd 12 2015 1 9 11 38 08 MMM o E EU Best model_IB_DB68 05163A_EN indd 13 2015 1 9 11 38 08 Remote controller display Transmit indicator Operation mode indicator Low battery indicator Set temperature Time for Timer option indicator Fan speed indicator api Fic am TE TK good sleep indicator cpm hr Se Vertical Horizontal air swing indicator Options indicator Single user Quiet cee dig io Settings indicator Make sure that the water does not get to the remote controller caution d light Cool function is displayed on the remote controller display but not supported in this model When turning off and turning on the remote controller the Timer Options and Settings set before turning off the remote controller are cancelled However the fan direction does not change Low Battery warning Inserting the batteries When the battery is exhausted 924 will be displayed in the 1 Push the lever as arrow indicates on the rear side of the remote controller display When the icon appears change remote controller and pull up the batteries The remote controller requires two 1 5 V AAA 2 Insert two AAA batteries type batteries Check and match the and
14. 267 www samsung com ee support EU Best model_IB_DB68 05163A_EN indd 36 DB68 05163A 00 2015 1 9 11 38 21 AR xJS Series ARKKHSXKX Series 100 Recycled Paper imagine the possibilities Thank you for purchasing this Samsung product nr EU Best model_IB_DB68 05163A_EN indd 37 2015 1 9 11 38 21
15. 67864 0 10 Min www samsung com nl support www samsung com be support Dutch BELGIUM 02 201 24 18 ig Art ao en N amp NORWAY 815 56480 www samsung com no support DENMARK 70701970 www samsung com dk support FINLAND 030 6227 515 www samsung com fi support SWEDEN 0771 726 7864 SAMSUNG www samsung com se support 0 801 172 678 lub 48 22 607 93 33 POLAND HHP 0 801 672 678 lub 48 22 607 93 33 www samsung com pl support koszt po czenia wed ug taryfy operatora HUNGARY PNA Dr A ie www samsung com hu support SLOVAKIA 0800 SAMSUNG 0800 726 786 www samsung com sk support AUSTRIA 0800 SAMSUNG 0800 7267864 www samsung com at support www samsung com ch support German SWITZERLAND 0800 726 78 64 0800 SAMSUNG ne ji va nel ie em a CZECH 800 SAMSUNG 800 726786 www samsung com cz support CROATIA 072 726 786 www samsung com hr support BOSNIA 051 331 999 www samsung com support MONTENEGRO 020 405 888 www samsung com support SLOVENIA 0 637 2 www samsung com si SERBIA 011 321 6899 www samsung com rs support BULGARIA 800 111 31 BesnnatHa Tene OHHa nuHuA www samsung com bg support ROMANIA 08008 726 Are can AMSUNG www samsung com ro support CYPRUS 8009 4000 only from landline toll free GREECE 80111 SAMSUNG 80111 726 7864 only from land line www samsung com gr support 30 210 6897691 from mobile and land line LITHUANIA 8 800 77777 www samsung com It support LATVIA 8000 7267 www samsung com lv support ESTONIA 800 7
16. and user maintenance shall not be made by children without supervision NOILYHVd34d LO FOR CLEANING A WARNING Do not clean the appliance by spraying water directly onto it Do not use benzene thinner or alcohol to clean the appliance This may result in discoloration deformation damage electric shock or fire Before cleaning or performing maintenance cut off the power supply and wait until the fan stops P Failing to do so may result in electric shock or fire FOR CLEANING _ A CAUTION Take care when cleaning the surface of the heat exchanger of the outdoor unit since it has sharp edges This should be done by a qualified technician please contact your installer or service center Do not clean the inside of the air conditioner by yourself D For cleaning inside the appliance contact your nearest service center gt When cleaning the internal filter refer to the descriptions in the Cleaning the air conditioner section Failure to do may result in damage electric shock or fire English 9 EU Best model_IB_DB68 05163A_EN indd 9 2015 1 9 11 38 07 ZS E Checking before use Operation ranges The table below indicates the temperature and humidity ranges the air conditioner can be operated within Refer to the table for efficient use Mode Indoor temperature Outdoor temperature Indoor humidity Cooling 16 C 32 C 10 C 46 C Relative humidity 80 or less
17. cator will turn on the indoor unit display Auto clean function will be activated after the air conditioner stops operating Duration of the Auto clean function can be different depending on the previous operation mode used Auto cool Cool Dry mode 30 minutes Auto heat Heat Fan mode 15 minutes gt Press the Settings button gt Press the I or Settings button to C aus make the Clean indicator blink and press the SET button Indoor unit display When the operation mode is set during Auto clean function is activated the air conditioner will operate in chosen operation mode and the Auto clean function will be re activated when the operation stops During the auto clean function indoor fan will continue to run and air flow blade will remain open to expel ambient air English 26 EU Best model_IB_DB68 05163A_EN indd 26 2015 1 9 11 38 17 ZS CSN UE Resetting the Filter clean reminder When Filter clean reminder CF lights up on the indoor unit display clean the filter and reset the reminder by following this instruction 1 Press the Settings button 2 Press the or Settings button until Filter Reset indicator starts to blink 3 Press the SET button to reset Filter clean reminder amp 3 seconds after setting Filter clean reminder function Filter Reset indicator on m the remote controller display will disappear and CF indicator on the indoor d unit display will
18. city consumed by operating the air conditioner When the air conditioner is operating 1 Press the Settings button 2 Press the Q or Settings button until Usage indicator starts to blink 3 Press the SET button to check the power consumption 3 seconds after setting power consumption checking function Usage indicator on the remote controller will disappear Indoor unit will display the amount of Power consumption for few seconds and then return to usual status by displaying the set indoor temperature Power consumption will be calculated from the moment the air conditioner is turned on and calculated value will be reset when the air conditioner turns off 0 1 is the default value of the electricity consumption and 99 is the maximum value Unit is in kWh When the air conditioner is not operating power consumption will not NOTE be displayed on the indoor unit display Indoor unit display Using the Auto clean function Auto clean function will minimise the moisture inside of the indoor unit Activate this function to help provide you with clean air When the air conditioner is operating 1 Press the Settings button 2 Press the or Settings button until Clean indicator starts to blink 3 Press the SET button to set the Auto clean function 3 seconds after setting Auto clean function Clean indicator on the remote controller display will disappear and Auto clean Timer D indi
19. d and remain on until the On timer turns on Off timer may not work depending on the On Off status of the indoor unit and the On Off status of the indicator on the remote controller display Only the latest setting timer will be applied between the On Timer Off Timer and good sleep Off timer functions Set wi Ke HD 1 EEE Remote controller display English 18 EU Best model_IB_DB68 05163A_EN indd 18 2015 1 9 11 38 11 Additional options available in On Off timer mode When the remote controller is on You can select from Auto Cool Dry Fan Heat YAWIL 0 Ge You can set the temperature after selecting the operation mode Temperature adjustment is available when Auto Cool Dry Heat mode is selected Setting on timer and off timer simultaneously Follow the same process for setting on timer and offtimer Remote controller display On timer and Off timer setting time should be different from each other NOTE Press the Power button on the remote controller while timer combination is on Both of the On and Off timer will be canceled and the indicator will disappear English 19 EU Best model_IB_DB68 05163A_EN indd 19 2015 1 9 11 38 11 ZS CSN EU good sleep mode For a comfortable sleep the air conditioner will operate in 3 stages in order of Fall asleep gt Sound sleep gt Wake up stage When the air conditioner is operating in Cool Hea
20. e selected by pressing the Mode button Auto 2 Step Cooling or Heat In Auto mode the air conditioner will automatically set the temperature and fan speed depending on the room temperature 2 Step Cooling mode sets the air conditioner to operate in Fast Cool mode when set temperature is lower than indoor temperature and then the air conditioner will automatically operate in Dry mode when indoor temperature reaches set temperature If using a multi system in Auto operation the system selects a temperature setting and an appropriate operation mode COOL or HEAT based on the room temperature at the start ofthe operation Cool In Cool mode the air conditioner will cool your room You can adjust the temperature and the fan speed to feel cooler in hot season If current outside temperature is much higher than the selected indoor temperature it may take time to bring the inner temperature to the desired coolness e Quiet mode makes the noise quieter during the operation of the indoor unit in the Cool mode Dry The air conditioner in Dry mode acts like a dehumidifier by removing moisture from the indoor air amp Dry mode makes the air feel refreshing in a humid climate To activate the Dry mode set temperature on the remote controller should be lower than indoor room temperature Fan Fan mode can be selected to circulate your room Fan mode will be helpful to refresh the stale air in your room Heat The air conditi
21. e up Allows you to wake up from comfortable intermittent air and it makes you feel refreshed Fan speed and the air flow direction will be adjusted automatically in good sleep mode Recommended set temperature is between 25 C 27 C for cooling and 21 C 23 C for heating Ifthe set temperature is too low you may feel cold during sleep or catch a cold Optimal operation hour of good sleep mode is 8 hours Therefore if the time is set too short or long you may not feel as comfortable as you would expect If the good sleep mode is set over 5 hours Wake up stage will begin when 1 hour is remaining in the operation time and the air conditioner will stop automatically When the On timer and the good sleep function is set simultaneously the air conditioner will only apply the function that was set later English 20 EU Best model_IB_DB68 05163A_EN indd 20 2015 1 9 11 38 12 ZS en mann 2 Step cooling function 2 Step Cooling function will set the air conditioner to cool the room quickly to reach the set temperature when the indoor temperature is higher than the set temperature and then the air conditioner will automatically operate in Dry mode when indoor temperature reaches set temperature When the air conditioner is operating in Cool mode 1 Press the Options button 2 Press the or Options button until 2 Step indicator starts to blink 3 Press the SET button to set the 2 Step C
22. emote controller display Using the Comfort function You can set the Comfort function to provide mild cooling heating When the air conditioner is operating in Cool Heat mode 1 Press the Options button 2 Press the lt G or Options button until Comfort indicator starts to blink 3 Press the SET button to set the Comfort function Comfort Comfort indicator will be displayed on the remote controller display and Comfort function will begin gt Press the Options button gt Press the amp gt or Options button to G SE make the Comfort indicator blink and press the SET button Comfort function is only available in Cool Heat mode NOTE Vertical Horizontal air swing can be adjusted Set temperature can be adjusted but fan speed cannot be adjusted Ifthe Comfort function is selected while 2 Step Cooling Fast Single user Quiet good sleep function is on corresponding function will be cancelled Remote controller display English 22 EU Best model_IB_DB68 05163A_EN indd 22 2015 1 9 11 38 14 MEME CSN NE Using the Single User function If using a multi system this function is not supported This function will reduce the energy usage while the air conditioner is operating in Cool Heat mode When the air conditioner is operating in Cool Heat mode 1 Press the Options button 2 Press the amp 2 or Options button until Single user indicator starts to blink 3 Pr
23. ess the SET button to set the Single user function Single user Single user indicator will be displayed on the remote controller display Then _ _ will be displayed on the set temperature indicator part for few seconds and Single user function will begin When the Single user function is on vertical air swing will turn on automatically Ifthe current set temperature is lower than 24 C in Cool mode it will be automatically raised to 24 C SNOILdO 70 gt Press the Options button gt Press the amp 2 or Options button to G au make the Single user indicator blink and press the SET button gt Single user function is only available in Cool Heat mode NOTE If the Single user function is selected while 2 Step Cooling Fast Comfort Quiet good sleep function is on corresponding function will be cancelled Single user Vertical air swing will remain on even after the Single user function is cancelled Remote controller display Additional options available in Single user function You can adjust the set temperature by 1 C within the range of 24 C 30 C in Cool mode and 16 C 30 C in Heat mode lt Auto Low 2 Med 2 High 2 Turbo can be selected Vertical Horizontal air swing can be selected English 23 EU Best model_IB_DB68 05163A_EN indd 23 2015 1 9 11 38 15 ZS CON EU Using the Quiet function Y
24. filter captures large particles from the air The filter is cleaned with a vacuum or by hand washing Remove the Air filter from the main body Clean the Air filter with a vacuum cleaner or soft brush If dust is too heavy rinse it with running water Insert the Air filter back in its original position Dry the Air filter in a ventilated area Clean the Air filter every 2 weeks Cleaning term may differ depending on the usage and environmental conditions In dusty area clean it once a week If the Air filter dries in a confined or humid area odors may generate If it occurs re clean and dry it in a well ventilated area When the filter clean reminder is on please press the 2 F button and then press the Single User button on remote controller English 30 EU Best model_IB_DB68 05163A_EN indd 30 2015 1 9 11 38 19 Reassembling the Air filter 1 Put the filter on the main body and insert the hooks which are Air filter in the top of the Air filter into the the main body SYAHLO 90 2 There s one hook in both side of the filter press the surface of the Air filter softly and get the hooks into the main body 3 Press the bottom of the filter lightly to securely fix the main body
25. g the service call Noise is generated Depending on the status of the air conditioner usage noise can be heard when refrigerant flow movement changes It is normal Smoke is If may not be a fire but it can be a steam generated by the generated from defrost operation from outdoor heat exchanger during the outdoor unit Heat mode in winter Water is dropping Water may be generated because of the temperature from the outdoor difference It is normal unit piping connection English 34 2015 1 9 11 38 20 EU Best model_IB_DB68 05163A_EN indd 35 English 35 SH1H1O 90 2015 1 9 11 38 20 QUESTIONS OR COMMENTS COUNTRY CALL OR VISIT US ONLINE AT UK 0330 SAMSUNG 7267864 www samsung com uk support EIRE 0818717100 www samsung com ie support 0180 6 SAMSUNG bzw 0180 6 7267864 0 20 Anruf aus dem dt Festnetz aus dem Mobilfunk max 0 60 Anruf GERMANY HHP 0180 6 M SAMSUNG bzw www samsung com de support 0180 6 67267864 0 20 Anruf aus dem dt Festnetz aus dem Mobilfunk max 0 60 Anruf FRANCE 01 48 63 00 00 www samsung com fr support ITALIA HHP Boel am se Bebe Dre 4 www samsung com it support SPAIN PT ee www samsung com es support PORTUGAL 808 20 7267 www samsung com pt support LUXEMBURG 261 03710 www samsung com support NETHERLANDS 0900 SAMSUNG 0900 72
26. h ground NOILYHVd34d LO FOR INSTALLATION A CAUTION Install your appliance on a level and hard floor that can support its weight Failing to do so may result in abnormal vibrations noise or problems with the product Install the draining hose properly so that water is drained correctly P Failing to do so may result in water overflowing and property damage Avoid adding drain to waste pipes as odours may arise in the future When installing the outdoor unit make sure to connect the draining hose so that draining is performed correctly D The water generated during the heating operation by the outdoor unit may overflow and result in property damage In particular in winter if a block of ice falls it may result in injury death or property damage FOR POWER SUPPLY 4 WARNING When the circuit breaker is damaged contact your nearest service center Do not pull or excessively bend the power line Do not twist or tie the power line Do not hook the power line over a metal object place a heavy object on the power line insert the power line between objects or push the power line into the space behind the appliance This may result in electric shock or fire English 5 EU Best model_IB_DB68 05163A_EN indd 5 2015 1 9 11 38 07 Ps o CHOSE Nu Safety precautions FOR POWER SUPPLY CAUTION When not using the air conditioner for a long period of time or during a thunder lightning storm
27. ic function Checking thename ofthe Parts s siissivaetssaancesaceseen see eeeadtadedaenuninadsoteecsetedssasadtiotsacieeuseasias sakes 11 Checking theremote controller nur oe nent fn nette trente 12 Basic function c eers tsas ennaa aE EEEE REENER EEEE EEEIEE ERETTE ERRE in raai 14 Adjusting theair flowdir ction i ns ei 16 Timer Setting the Current time ss on 17 Setting the On Off UME sa mn CSEE nee nr EE ete seaes 18 9008 SIEEPIMOE en badeoad one ni en 20 Options 2 Step cooling f nction mm i cage eanandteneddaaeay sales eet ES Le Rise stunt 21 UsingthelFasttunctioN a en UERR E EE EEEO REE EERE 22 Using the Comfort function nn ei 22 Usingthe Single Userfuretion am seen a te ce en t inerte einen ts 23 Using the Quiet function ee dn ERE nettes 24 Using the Virus Doctor functiom sm re Eo nEaN VUANTE EEE EEEE OEE EEEREN EER ERE 25 Settings Checking the power CONSUMPTION 26 Using the Auto clean function een essaie men naeh re ee 26 Resetting the Filter clean reminder eisen area nee 27 Setting the Display option nn Ares rear M DIRT ee en Kerr de OUR 27 Setting the Beep sound sa dette tent asiuinemeaas sui quae EEE EEEE EERE EEEE N NEEE 28 Using the Smart A Capplicationess siennes sees see tana nn 28 Others Cleaning the Air Conditie seess en tinari sse EEEE KEENE nenne hehe 29 Mainta iningttheiais conditi ner n tsar tE rE nonea a er eee er etienne THEE EEEE 32 Troubleshooting ey a i ed in ee 33 English 3
28. iling to do so may result in electric shock or fire Do not attempt to repair disassemble or modify the appliance yourself gt Do not use any fuse such as cooper steel wire etc other than the standard fuse Failing to do so may result in electric shock fire problems with the product or injury English 7 EU Best model_IB_DB68 05163A_EN indd 7 2015 1 9 11 38 07 Safety precautions FOR USING ACAUTION Do not place objects or devices under the indoor unit gt Water dripping from the indoor unit may result in fire or property damage example electrical appliances Check that the installation frame of the outdoor unit is not broken at least once a year P Failing to do so may result in injury death or property damage Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency Do not stand on top of the appliance or place objects such as laundry lighted candles lighted cigarettes dishes chemicals metal objects etc on the appliance This may result in electric shock fire problems with the product or injury Do not operate the appliance with wet hands This may result in electric shock Do not spray volatile material such as insecticide onto the surface of the appliance D As well as being harmful to humans it may also result in electric shock fire or problems with the product Do not drink the wa
29. ime in hourly units from 1 hour 12 hours according to AM PM and in minute units from 0 59 minutes 3 Press the SET button to complete the On off timer setting On Off indicator and the set time of the timer will be displayed on the remote controller display and the Timer indicator will be displayed on the indoor Setting On ti Seeks unit display On Off timer setting will be cancelled if you don t press the SET button within 10 seconds after setting the time Therefore check for the On Off indicator on the remote controller display and the Timer indicator on the indoor unit display gt Press the Timer button gt select On Off gt press the Q or button Cancel gt set the timer to press the SET button amp gt Press the Power button When On Off timer setting is completed the set status will be displayed Remote controller display for 3 seconds and then only On Off indicator will remain on the remote controller display thereafter Ifyou press the Power I button on the indoor unit after setting the On Off timer from the remote controller Timer indicator on the indoor unit display will disappear and the On Off timer will be cancelled Even though the On Off timer is cancelled On Off indicator on the remote Setting Off timer Auto controller will remain displayed When the On timer is set while the air conditioner is off Timer indicator will be displaye
30. ly Easy Installation It s so easy to install You can easily hang the product on the wall and connect the pipes and wires by opening the cover on the bottom of the product Now you won t have to tilt the product to connect the pipe and the wires xf Correct Disposal of This Product Waste Electrical amp Electronic Equipment Le Applicable in countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal English 2 EU Best model_IB_DB68 05163A_EN indd 2 2015 1 9 11 38 06 Contents Preparation Safetyiprecautions sed ne a 4 Checking before use nie 10 Bas
31. n EICH indicator will be displayed on the remote controller display and Virus Doctor function will begin SNOILdO 70 gt Press the Options button gt Press the amp DJ or Options button to G ot His make the indicator blink and press the SET button Virus Doctor lamp will turn on when the Virus Doctor function turns on and it will turn off when the function is cancelled Virus Doctor function can be selected while Auto Cool Dry Fan Heat mode is on Set temperature can be adjusted Auto There will not be much difference on energy consumption and operating noise when the Virus Doctor function is selected additionally while the other function is on When the Virus Doctor function is selected with other operation mode pressing the Power button will stop the operation Remote controller display When the air conditioner is not in operation 1 Press the Options button 2 When the 23 indicator blinks press the SET button to select the Virus Doctor function CORTE indicator will be displayed on the remote controller display and Virus Doctor function will begin gt Press the Options button to make the 833 indicator blink and press Cancel the SET button gt Press the Power button English 25 EU Best model_IB_DB68 05163A_EN indd 25 2015 1 9 11 38 16 ZS CON NE Checking the power consumption This function will display the amount of electri
32. on If the good sleep mode is operating in Heat mode you can adjust the air flow direction Fan speed adjustment is not working Check if you have selected Auto Dry Fast Comfort good sleep mode In these mode fan speed is set to Auto and you cannot adjust the fan speed Remote controller is not working Check if your batteries are depleted Make sure nothing is blocking your remote controller sensor Check that there are strong lighting apparatus near the air conditioner Strong light which comes from fluorescent bulbs or neon signs may interrupt the electric waves Timer function Check if you press the Set Cancel button on the remote does not set controller after you have set the time The indicator Press the Power button or disconnect the power plug is blinking switch off the auxiliary power switch amp EU Best model_IB_DB68 05163A_EN indd 34 continuously If the indicator is still blinking contact the service center Odors permeate in the room during operation Check if the appliance is running in a smoky area Ventilate the room or operate the air conditioner in Fan mode for 1 2 hours We do not use smelly components in the air conditioner Check the Drains have been cleared Regular Maintenance Error is indicated When an indoor unit indicator blinks contact the nearest service center Please ensure the error code is passed onto the service center when bookin
33. on of this appliance must be performed by a qualified technician or service company Failing to do so may result in electric shock fire explosion problems with the product or injury and may also void warranty on the installed product Install a Isolation Switch next to the Air Conditioner but not on the panels of the Air Conditioner and circuit breaker dedicated to the air conditioner Failing to do so may result in electric shock or fire Fix the outdoor unit firmly so that the electric part of the outdoor unit is not exposed Failing to do so may result in electric shock fire explosion problems with the product English 4 EU Best model_IB_DB68 05163A_EN indd 4 2015 1 9 11 38 07 ZS EU Do not install this appliance near a heater inflammable material Do not install this appliance in a humid oily or dusty location in a location exposed to direct sunlight and water rain drops Do not install this appliance in a location where gas may leak This may result in electric shock or fire Never install the outdoor unit in a location such as on a high external wall where it could fall P Ifthe outdoor unit falls it may result in injury death or property damage This appliance must be properly grounded Do not ground the appliance toa gas pipe plastic water pipe or telephone line Failure to do so may result in electric shock fire and explosion gt Make sure to use a socket outlet wit
34. oner heats as well as cools Warm your room with this versatile appliance in the cold of winter Fan may not operate for about 3 5 minutes at the beginning to prevent any cold blasts while the air conditioner is warming up Quiet mode makes the noise quieter during the operation of the indoor unit in the Heat mode Since the air conditioner heats the room by taking heat energy from outdoor air the heating capacity may decrease when outdoor temperature is extremely low Use an additional heating appliance in combination with the air conditioner if you feel the air conditioner heats insufficiently English 14 EU Best model_IB_DB68 05163A_EN indd 14 amp 2015 1 9 11 38 08 Press the button to turn on the air conditioner Press the button to set the operating mode Each time you press the Mode button the mode will change in order of Auto Cool Dry Fan and Heat Auto Cool Heat Set K Set C IL IL 30 Set LI NOIL2NndJ DISV4 ZO Press the button to adjust the temperature Auto You can adjust the set temperature by 1 C within the range of 16 C 30 C Cool You can adjust the set temperature by 1 C within the range of 16 C 30 C Dry You can adjust the set temperature by 1 C within the range of 18 C 30 C Fan Temperature adjustment is not possible Heat You can adjust the
35. ooling function 2 Step 2 Step indicator will be displayed on the remote controller display and 2 Step Cooling function will begin SNOILdO 70 gt Press the Options button gt Press the C C or Options button to Cancel make the 2 Step indicator blink and press the SET button Remote controller display English 21 EU Best model_IB_DB68 05163A_EN indd 21 2015 1 9 11 38 13 ZS CON NE Using the Fast function You can set the Fast function to provide fast and powerful cooling heating When the air conditioner is operating in Cool Heat mode 1 Press the Options button 2 Press the or Options button until Fast indicator starts to blink 3 Press the SET button to set the Fast function Fast Fast indicator will be displayed on the remote controller display and Fast function will begin gt Press the Options button gt Press the amp DJ or Options button to make the Fast indicator blink and press the SET button Cancel Fast function is only available in Cool Heat mode NOTE Vertical Horizontal air swing can be adjusted Set temperature and fan speed cannot be adjusted If the Fast function is selected while 2 Step Cooling Comfort Single user Quiet good sleep function is on corresponding function will be cancelled When you select Fast function in Heat mode you may not be able to increase fan speed in order to prevent any cool air from blowing R
36. ore using the functions of the air conditioner set the current time 1 Press the Settings button 2 Press the Q or Settings button until Colck indicator starts to blink 3 Press the SET button to set the Colck function Colck Colck indicator will be displayed on the remote controller display and you can set the time 4 Press the button to set the time You can set the time in hourly units from 1 hour 12 hours according to AM PM and in minute units from 0 59 minutes YAWIL 0 5 Press the SET button to complete the current time setting Current time setting will be cancelled if you don t press the SET button within 10 seconds after setting the time Therefore check for the current time on the remote controller display Remote controller display English 17 EU Best model_IB_DB68 05163A_EN indd 17 2015 1 9 11 38 10 Setting the On Off timer Check the current time on the remote controller before using this function caution The default time is 1 AM on the remote controller The current time is reset to default time after changing the batteries You can set the air conditioner to turn on off automatically at desired time Setting On timer while the air conditioner is off Off timer while the air conditioner is on 1 Press the Timer button to select On Off On Off indicator will keep blinking and you can set the time 2 Press the button to set the time You can set the t
37. ou can reduce the noise generated from an indoor unit during Cool Heat mode When the air conditioner is operating in Cool Heat mode 1 Press the Options button 2 Press the X C or Options button until Quiet indicator starts to blink 3 Press the SET button to set the Quiet function Quiet Quiet indicator will be displayed on the remote controller display and Quiet function will begin gt Press the Options button gt Press the amp gt or Options button to Cancel make the Quiet indicator blink and press the SET button Additional options available in Quiet function ids You can adjust the set temperature by 1 C within the range of w 16 C 30 C 7N Fam Fan speed is set to lt Auto v Remote controller display Vertical Horizontal air swing can be selected Quiet function is only available in Cool Heat mode NOTE If the Quiet function is selected while 2 Step Cooling Fast Comfort Single user good sleep function is on corresponding function will be cancelled English 24 EU Best model_IB_DB68 05163A_EN indd 24 2015 1 9 11 38 15 Zl E Using the Virus Doctor function This function will produce positive ions and supply them into the airflow When the air conditioner is operating 1 Press the Options button 2 Press the or Options button until 3 indicator starts to blink 3 Press the SET button to set the Virus Doctor functio
38. p indicator on the remote controller display will disappear and Beep sound function will begin Using the Smart A C application You can conveniently control your air conditioner anywhere with Smart APP WIFI WPS is not seen to new remote control LCD It is hidden function 1 Press the Timer button to set the WiFi function Press the Timer button for 4 seconds will blink first then appears on the remote controller display for few seconds and disappears WiFi function will begin 2 Press the Settings button to set the WPS function Press the Settings button for 4 seconds T will blink first then disappears and WPS function will begin For detail information please refer to Smart A C application manual NOTE Smart A C application may not be available for some models Remote controller display English 28 EU Best model_IB_DB68 05163A_EN indd 28 2015 1 9 11 38 18 ZS E Cleaning the air conditioner Make sure to turn off the power of the indoor unit and cut off CAUTION the power supply before cleaning the air conditioner Cleaning the indoor unit gt Clean the product with a tepid damp cloth gt Remove the dust accumulated in the gap of the product with a soft brush SY3HLO 90 Contact the service center when you clean the indoor unit note heat exchanger because it needs to be disassembled Do not clean the
39. rost cycle Protect compressor The air conditioner does not start operating immediately to help protect the compressor of the outdoor unit after it has been started Ifthe heat pump is operating in Heat mode defrost cycle is actuated to help remove frost from an outdoor NOTE unit that may have deposited at low temperatures The internal fan is switched off automatically and restarted only after the defrost cycle is completed Smart install If using a multi system this function is not supported gt Through Smart install function installer can check if the installation was done properly gt Ifthe installation was not done properly error indicator will turn on the indoor unit display Therefore user will know if the installation was done properly or not English 10 EU Best model_IB_DB68 05163A_EN indd 10 2015 1 9 11 38 07 ZS a mann Checking the name of the parts Your air conditioner may slightly look different from illustration shown below depending on your model Main parts Room temperature sensor NOILDNNA DISV4 ZO D EG Wi Fi module Air filter Air intake f Virus Doctor Lamp Virus Doctor Vertical air flow blade Horizontal air flow blades Temperature indicator Filter Clean reminder indicator EF Defrost indicator 4F Power
40. set temperature is higher during Cool mode does not come lower during Heat mode than the current temperature out of the air Press the Temp or button on the remote controller to conditioner change the set temperature Check if the Air filter is blocked by dirt If there is a lot of dust on the Air filter cooling heating performance may decrease Clean them frequently Check if the outdoor unit is covered or installed near the obstacle Take the cover off and take the obstacle away Check if the air conditioner is operating in defrost mode When the ice formed in winter or the outdoor temperature is too low the air conditioner operates in defrost mode automatically In defrost mode indoor fan stops and warm air does not come out If the doors or windows are open it may cause bad cooling heating performance Close the doors and windows Check if the air conditioner has just been turned on after stopping cooling or heating operation In this case just a fan will run to protect the outdoor unit compressor Check if the pipe length is too long When the pipe length exceeds maximum allowable pipe length cooling heating performance may decrease English 33 EU Best model_IB_DB68 05163A_EN indd 33 2015 1 9 11 38 20 mE Troubleshooting PROBLEM SOLUTION Air flow Check if you have selected good sleep mode In cool mode adjustment is not working you cannot adjust the air flow directi
41. t mode 1 Press the Timer button to select Co indicator will keep blinking and you can set the time 2 Press the button to set the time You can set the time in half hour unit from 30 minutes 0 5 on the display 3 hours and hour unit from 3 12 hours Time can be set from minimum 30 minutes to maximum 12 hours Default time setting for the good sleep mode is 8 hours 3 Press the SET button to complete the good sleep mode setting Cool indicator and the set time of the good sleep mode will be displayed on em the remote controller display EE En c Timer indicator will be displayed on the indoor unit display on I wt good sleep mode setting will be cancelled if you don t press the SET button within yan H Di 30 10 seconds after setting the time Therefore check for the indicator on the remote controller display and the Timer indicator on the indoor unit display gt Press the Timer button select Xd gt press the CJ or C button gt set the timer to gt press the SET button Cancel Remote controller display Additional options available in good sleep mode You can adjust the set temperature by 1 C within the range of 16 C 30 C Temperature and fan speed change in good sleep mode Fall asleep Eases you into sleep by dropping the temperature Sound sleep Relaxes your body and raises your temperature slightly Wak
42. ter from the air conditioner gt The water may be harmful to humans Do not apply a strong impact to the remote controller and do not disassemble the remote controller Do not touch the pipes connected with the product This may result in burns or injury Do not use this air conditioner to preserve precision equipment food animals plants or cosmetics or for any other unusual purposes This may result in property damage Avoid directly exposing humans animals or plants from the air flow from the air conditioner for long periods of time This may result in harm to humans animals or plants English 8 EU Best model_IB_DB68 05163A_EN indd 8 2015 1 9 11 38 07 ZS EU This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance For use in Europe This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning
Download Pdf Manuals
Related Search