Samsung SH07ZZ8 Наръчник за потребителя
Contents
1. q gt setting the Sleep Timer N CD ET TEMP te n ty The Sleep Timer can be used when you are cooling or heating your room to switch the air conditioner off automatically after a period of 6 hours Note If you wish to switch the unit off at a specific time refer to page 19 1 Make sure that you have selected either COOL or HEAT mode 2 Press the button one or more times until 2 appears on the remote control Result The indoor unit beeps 4 The air conditioner will be controlled as indicated in the illustrations below Cooling The desired temperature is increased by 1 C every hour When it has been increased by 2 C after 2 hours the temperature is maintained for four hours Heating The desired temperature is decreased by 1 C every hour When it has been decreased by 2 C after 2 hours the temperature is maintained for four hours To Cancel the Sleep Timer If you no longer wish to use the Sleep Timer that you have set you can cancel it at any time Press the button Result The indoor unit beeps The Z is no longer displayed The air conditioner operates normally Operating Recommendations Here are a few recommendations that you should follow when using your air conditioner Topic Recommendation Heating performances The heat pump inside the air conditioner absorbs heat from outside air and bring2. The indoor unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Ifthe X is not displayed at the top of the remote control press the button on the remote control one or more times until it appears Result 4 The indoor unit beeps each time you press the button The air conditioner runs in COOL mode Mote You can change modes at any time 3 To adjust the temperature press the gt button one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press the C 5 button The temperature is adjusted by 1 C The indoor unit beeps The air conditioner starts cooling provided that the room temperature is higher than the selected temperature If the room temperature reaches the set temperature the air conditioner stops cooling but the fan is still operating 4 Select the fan speed by pressing the button one or more times until the required setting is displayed Jer Automatic rotated 5 hur Parl ols Low ul Medium Sail High Result Each time you press the button the indoor unit beeps 5 To control the direction of the air flow refer to pages 16 and 17 Heating Your Room You must select the Heat mode if you wish to adjust the Hea
3. can still be controlled using the remote control as usual Solving Common Problems Before contacting the after sales service perform the following simple checks They may save you the time and expense of an unnecessary call Problem The air conditioner does not operate at all The air conditioner does not operate with the remote control No beep is heard when you press the On Off on the remote control The air conditioner does not cool or heat When heating the required room temperature is never reached and the air conditioner frequently stops The fan speed does not change when you press the button The air flow direction does not change when you press the button The timer is not correctly triggered Odour is permeated in the room during air conditioning 49 o 9 4 Explanation Solution Check that the breaker used for the air conditioner is switched on if necessary press the amp 5 On Off button on the remote control Check whether the Timer indicator on the indoor unit is switched on If so Wait until the switch on time is reached and the air conditioner starts up automatically Cancel the timer see pages 18 and 19 for further details Check that there are no obstacles between you and the indoor unit Check the remote control batteries Check that you are close enough to the indoor unit seven meters yards or less Check that you are pointing the remote control at t
4. have finished insert the filter into the grille 5 Insert the top part of the front grille into their slots and push down on the bottom slots until they click into place 6 Clean the front grille with a damp cloth and mild detergent do NOT use benzene solvents or other chemicals Note If you have not used the air conditioner for a long period of time set the fan going for three to four hours to dry the inside of the air conditioner thoroughly Upper front grille THIS AIR CONDITIONER IS MANUFACTURED BY AD ELECTRONICS
5. 8 OPERATING YOUR AIR CONDITIONER m Selecting the Automatic Operating Mode 9 m Cooling Your ROOM suus xo dun tex Nea Uep RECO et En 10 m Heating Your Room eneen 11 m Changing the Room Temperature Quickly 12 m Removing Excess Humidity 13 m Airing Your Room esc aaa a ee ee en et ae qoe eus EROR C ds 14 m Selecting Energy Saving Mode 15 m Adjusting the Air Flow Direction Vertically 16 m Adjusting the Air Flow Direction Horizontally 17 PROGRAMMING YOUR AIR CONDITIONER m Setting the On Timer nennen 18 mcsetingiheOflimer 19 mSetingiheSleeplimer 20 RECOMMENDATIONS FOR USE m Operating Recommendations 21 mlemperaturrandHumidiiyRanges 22 m Operating Your Air Conditioner Without the Remote Control 23 msolvingCommonProblems 24 m Cleaning Your Air Conditioner 25 View of the Unit The design and shape are subject to change according to the model Air filter Air Inlet under the grille Air flow blades outlet Operation indicator Remote Control Sensor Green On Off button Turbo indicator Green Timer indi
6. OWNER gt INSTRUCTIONS Indoor unit Outdoor unit SH05778 SH05778X SH07778 SH07778X SPLIT TYPE ROOM AIR CONDITIONER Cool and Heat ER DB98 15865A 1 Safety Precautions The following safety precautions must be taken when using your air conditioner N WARNING DURING OPERATION DISPOSING OF THE UNIT OTHERS Risk of electric shock e Can cause injury or death e Disconnect all remote electric power supplies before servicing installing or cleaning This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard Users of this product are cautioned not to attempt repair of this product at their own discretion Instead they are requested to directly contact a designated service center or the outlet at which the product was purchased Never spill any kind of liquid into the unit Should this happen unplug or main switch off the unit and contact an authorized service center Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury Keep children away from the unit Do not place any obstacles in front of the unit Do not spray liquid of any kind into the indoor unit Should this happen switch off the breaker used for your air conditioner and contact your installation specialist Make sure that the unit is correctly ventilated at all times Do not place clothing or other materials over it If t
7. air conditioner automatically after a given period of time You can set the period of time from 30 minutes to 24 hours 1 To set the operating time press the button one or more times until the required time is displayed Possible time is between 0 5 hour and 24 hours inclusive 2 Press the 96 Set Cancel button to complete the setting Result o The remaining time is displayed Blinking of the timer indicator stops The air conditioner will switch off automatically when the fil counter displayed on the remote control reaches the set time gt and disappears the Off timer setting Example If you would like to turn the air conditioner on after 2 hours and to operate it for 2 hours 1 Press the button until 2 0 Hr is displayed Energy Saving 2 Press the Set Cancel button Ss A 3 Press the button until 4 0 Hr is displayed m 4 Press the Set Cancel button Note You can see or change the setting mode and or the temperature by pressing the button or the GS button after setting the Off timer To Cancel the Off Timer ee 1 To cancel the Off Timer press the button one or more times until the ul timer setting disappears miz W On Timer poe a 2 Press the Set Cancel button Note If you want to turn off the air conditioner before the timer reaches IT ey the setting time press the On Off button P3 0
8. cator Orange Air Inlet Rear Air Outlet Connection Valve inside Remote Control Buttons and Display Remote control transmission indicator C Mode Mode selection button Operating mode AUTO COOL DRY FAN HEAT AUTO amp COOL DRY i ep FAN HEAT 24 D Temperature adjustment Temperature setting Vs buttons Turbo mode Sleep mode Energy saving CTurbo 23 1 Turbo Sleep mode selection button r 4 Fan speed adjustment button Fan speed Ti M Air flow direction aca Swing button On Timer setting On Timer On Timer button am Off Timer setting Off Timer Off Timer button Battery discharge indicator On Off amp Energy Saving button Timer Set Cancel button Getting Started 60020000090900009000090990090099000099000009000099900000990000909000090000099000909000000900000990009090000090000090000099000009000000900090090000009000090000990000990009 You have just purchased a split type air conditioner and it has been installed by your installation specialist Your Owners Instructions contains valuable information on using your air conditioner Please take the time to read it as it will help you take full advantage of the unit s features The booklet is organized as follows The following figures are shown on pages from 4 to 6 Indoor and outdoor units Remote control buttons and display They wil
9. conditioner cools or heats the room as quickly as possible After 30 minutes the air conditioner is reset automatically to the previous mode temperature and fan settings But if you press the button in DRY or FAN mode it will change to AUTO mode automatically 3 If you wish to stop the Turbo function before the end of the 30 minute period press the Guw3 button one or more times until or 2 disappears Result The air conditioner is reset automatically to the previous mode temperature and fan settings 4 To control the direction of the air flow refer to pages 16 and 17 Removing Excess Humidity If the atmosphere in your room is very humid or damp you can remove excess humidity without lowering the room temperature too much e 1 If necessary press the 2 On Off button gt J q Result The operation indicator on the indoor unit lights up On Timer The air conditioner starts up in the mode selected when Sa E the unit was last used Off Timer The indoor unit beeps PORTANT The air conditioner is fitted with a protection mechanism EC OY to prevent the unit from being damaged when it is started AV b immediately after being uw Plugged in b Stopped he It will start up normally after three minutes 2 Ifthe C is not displayed at the top of the remote control press the button on the remote control one or more times u
10. e temperature 5 To select the fan speed press the Q the required setting is displayed button one or more times until 6 To control the direction of the air flow refer to pages 16 and 17 gt m Viod iL Mode CAS 7 Adjusting the Air Flow Direction Vertically Depending on the position of the indoor unit on the wall of your room you can adjust the position of the outer air flow blade on the bottom of the unit thus increasing the efficiency of the air conditioner SET TEMP LK gt 1 Press the button one or more times as required C N l QV Result The outer blade is adjusted vertically RECOMMENDATION When Adjust the blade to face en Cooling Upwards awd 4 Heating Downwards E e On Timer gt 2 If you want the blade to move up and down automatically when the air conditioner is operating press the button Result The blade moves up and down around the base position set 3 To stop the blade moving up and down press the button again Mote Ifyou switch the air conditioner Then the blade is Off Closed completely On again Set to the initial position powered Adjusting the Air Flow Direction Horizontally There are two sets of inner air flow blades Just as the outer air flow blade can be adjusted vertically the inner blades can be adjusted horizontally 1 Adjust each set of inner blades to the required position by pus
11. ected when the unit was last used The indoor unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Ifthe a is not displayed at the top of the remote control press the button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the button The air conditioner runs in AUTO mode Mote You can change modes at any time 3 To adjust the standard temperature The air conditioner automatically set the standard temperature by the current room temperature press the gt button one or more times SET TEMP SET TEMP 2 C 1 C SET TEMP SET TEMP Standard temperature 1 C 2 C lt When you feel hot gt lt When you feel chilly gt Energy Saving SET TEMP we On Timer gnCe 4 lO x iu a Cooling Your Room Energy Saving SET TEMP i e You must select the Cool mode if you wish to adjust the Cooling temperature Fan speed when cooling 1 If necessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used
12. he remote control sensor in the right of the indoor unit Replace the remote control batteries if necessary Check that the correct operating mode has been selected AUTO COOL HEAT The room temperature may be too low or too high Dust may be blocking the air filter guard refer to page 25 for cleaning instructions Check that there is no obstacle in front of the outdoor unit Check that the required temperature has been set correctly Increase the fan speed If the air flow is directed upwards use the remote control to direct it downwards Check that the operating mode is set to COOL HEAT or FAN in the AUTO mode the fan speed changes automatically and in the DRY mode it is set to AUTO Check that the air conditioner has been switched on if necessary press the On Off button on the remote control Check that the timer has been programmed correctly see pages 18 and 19 Air the room Cleaning Your Air Conditioner To get the best possible use out of your air conditioner you must clean it regularly to remove the dust that accumulates on the air filter PORTANT Before cleaning your air conditioner ensure that you have switched off the breaker used for the unit 1 Press the right and left marks of the front grille pushing it 2 Remove the front grille from the indoor unit to remove the air filter 3 Remove all dust on the air filter with a vacuum cleaner or brush 4 When you
13. he wireless remote control will not be used for a long time remove the batteries If applicable When using a wireless remote control the distance should not be more than 7 meters from the air conditioner If applicable Before throwing out the device it is necessary to pull back the battery cells and get rid of them safely for recycling reasons When you need to dispose of the unit consult your dealer If pipes are removed incorrectly refrigerant may blow out and come into contact with your skin causing injury Releasing refrigerant into the atmosphere also damages the environments Please recycle or dispose of the packaging material for this product in an environmentally responsible manner Never store or ship the air conditioner upside down or sideways to avoid damage to the compressor The appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency Contents PREPARING YOUR AIR CONDITIONER m Safety Precautions sese x andermans 2 m View of the Unit een te Be e aak RE ke ERE EE ER 4 m Remote Control Buttons and Display 6 m Getting Started 7 m nserting the Remote Control Batteries
14. hing or pulling them sideways Setting the On Timer CD LH oH Off Timer e The On Timer enables you to switch on the air conditioner automatically after a given period of time You can set the period of time from 30 minutes to 24 hours To set the operating time press the OnTime button one or more times until the required time is displayed Possible time is between 0 5 hour and 24 hours inclusive Press the Set Cancel button to complete the setting Result The remaining time is displayed Blinking of the timer indicator stops The selected mode and the temperature on the display disappear after 10 seconds The air conditioner will switch on automatically when the counter displayed on the remote control reaches the set time and disappears the On timer setting To select an operating mode in advance press the amp Mede button until the desired mode is displayed at the top of the remote control Result The air conditioner will run in the selected mode when it is turned on To Cancel the On Timer 1 To cancel the On Timer press the button one or more times until the timer setting disappears 2 Press the 56 Set Cancel button Note If you want to turn on the air conditioner before the timer reaches the setting time press the On Of button setting the Off Timer The Off Timer enables you to switch off the
15. ic protection feature may be triggered and the air conditioner stopped Low temperatures A water leak or some other malfunction may occur if the heat exchanger freezes High humidity levels Water may condense on and drip from the surface of the indoor unit if it is used for long periods Mode Outdoor Temperature Indoor Temperature Indoor Humidity Heating 0 C to 24 C approx 27 C or less Cooling 21 C to 43 C approx 18 C to 32 C approx 80 or less Drying 18 C to 43 C approx 18 C to 32 C approx Ifthe heating operation is used at below 0 C outdoor temperature it does not heat at its full capacity If the cooling operation is used at over 33 C indoor temperature it does not cool at its full capacity Operating Your Air Conditioner Without the Remote Control Your air conditioner can be operated directly from the indoor unit if the remote control is lost or broken 1 To turn the air conditioner on press the On Off button on the right side m of the indoor unit Result The Operation indicator on the indoor unit comes on The indoor unit beeps 4 The air conditioner starts up in the most suitable mode for the room temperature Room Temperature Operating Mode Temperature Setting Less than 21 C Heat 22 C approx 21 C or above Cool 24 C approx 2 To turn the air conditioner off press the On Off button again Note Even if the air conditioner has been turned on via the On Off button operations
16. l help you find the buttons and understand the symbols displayed Inthe manual you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use three different symbols HOLD DOWN Inserting the Remote Control Batteries You must insert or replace the remote control batteries when You purchase the air conditioner The remote control does not work correctly Note Use two AAA LRO3 1 5V batteries Do not use old batteries or different kinds of batteries together Batteries may be completely discharged after 12 months even if they have not actually been used 1 Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it 2 Insert the two batteries taking care to respect the polarities on the battery with on the remote control on the battery with on the remote control 3 Close the cover by sliding it back until it clicks into place Selecting the Automatic Operating Mode You can start the air conditioner in Automatic mode from your remote control In the Automatic mode the standard temperature and the optimum fan speed is selected automatically You can adjust the standard temperature but not the fan speed 1 If necessary press the 9 On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode sel
17. ntil it appears 4a Result The indoor unit beeps each time you press the button Mode The air conditioner runs in DRY mode Ak Note You can change modes at any time co 3 To adjust the temperature press the button one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive la Result Each time you press the gt button f The temperature is adjusted by 1 C The indoor unit beeps IN n The air conditioner starts removing the excess humidity G Mode the quantity of air is adjusted automatically I C pru i 4 SET TEMP GAS gcn i Pca SV 4 To control the direction of the air flow refer to pages 16 and 17 Tl p Airing Your Room If the atmosphere in your room is stale you can air the room using the Fan feature 1 If necessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps 2 Ifthe of is not displayed at the top of the remote control press the button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the button 4 The air conditioner runs in FAN mode The temperature is set automatically Mote You can change modes at any time 3 Select the fan speed by pressing the bu
18. s it indoors If the temperature of the outside air drops the air conditioner will heat less If you find that the room is not warm enough use an additional heating appliance Warm air circulation The air conditioner circulates warm air to heat your room as a result some time will be required after starting the air conditioner to warm the entire room If necessary set the air conditioner on before you wish to use the room Frost When outside temperatures are low and humidity is high frost may form in the outdoor unit when heating is selected If this happens The heating operation is stopped The Deice mode is triggered automatically for about seven minutes No intervention is required from you after about seven minutes the air conditioner starts operating again normally High indoor and outdoor If both the indoor and outdoor temperatures temperatures are high and you select the Heat mode the outdoor unit s fan and compressor may stop at times This is normal simply wait until the air conditioner switches on again Power failure If a power failure occurs when the air conditioner is operating the unit is switched off When the power returns the air conditioner starts up again automatically Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used If the air conditioner is used at Then High temperatures The automat
19. ting temperature Fan speed when heating 1 If necessary press the 69 On Off button 5 Result The operation indicator on the indoor unit lights up On Timer The air conditioner starts up in the mode selected when Nm the unit was last used OffTimer 8 The indoor unit beeps I g ln 4 PORTANT The air conditioner is fitted with a protection mechanism en ee to prevent the unit from being damaged when it is started 220 immediately after being VA Plugged in N Stopped bs It will start up normally after three minutes 2 Ifthe is not displayed at the top of the remote control press the nn button on the remote control one or more times until it appears Result The indoor unit beeps each time you press the button The air conditioner runs in HEAT mode gn 4a Mote You can change modes at any time Mode CANS i i C maa 3 To adjust the temperature press the S button one or more times r4 VA until the reguired temperature is displayed Possible temperatures are between 16 C and 30 C inclusive Result Each time you press the button The temperature is adjusted by 1 C The indoor unit beeps em The air conditioner starts heating provided that the room temperature is lower than the desired temperature selected temperature 3 C If the room temperature reaches the set temperature the air IW conditioner s
20. tops heating but the fan is still operating xk mi 4 chs n SET TEMPE o Q 3s gre 4 Select the fan speed by pressing the button one or more times Lt KY until the required setting is displayed ser Automatic rotated se Dar gt il M a Low SAT Medium SI Result Each time you press the button the indoor unit beeps Eau UV For the first three to five minutes the fan operates very DM slowly until the air has been sufficiently warmed Once the correct temperature has been reached the fan is automatically set to the required speed ani On Timer 5 To control the direction of the air flow refer to pages 16 and 17 Changing the Room Temperature Quickly The Turbo cooling heating function is used to cool or heat your room as quickly as possible Example You have just come home and find that the room is very hot You wish to cool it down as quickly as possible The Turbo function operates for 30 minutes with the maximum settings before returning automatically to the mode and temperature previously selected 1 If necessary press the onop button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps 2 Press the button Result The temperature and fan settings are adjusted automatically The air
21. tton one or more times until the required setting is displayed p Low Medium il High Result Each time you press the button the indoor unit beeps 4 To control the direction of the air flow refer to pages 16 and 17 Selecting Energy Saving Mode If you wish to save energy when using your air conditioner select the Energy saving mode with the Energy saving button 1 If necessary press the On Off button Result The operation indicator on the indoor unit lights up The air conditioner starts up in the mode selected when the unit was last used The indoor unit beeps PORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up normally after three minutes 2 Select COOL mode by pressing the ode button Note You can select the Energy saving mode only in COOL mode 3 Press the lt gt button Result The indoor unit beeps The air conditioner runs in the Energy saving mode The outer air flow blade moves up and down _ To stop the Energy saving mode press the 25 again 4 To adjust the temperature press the gt button one or more times until the reguired temperature is displayed Possible temperatures are between 26 C and 30 C inclusive Note If you want to adjust temperature under 26 C cancel the Energy saving mode before adjusting th
Download Pdf Manuals
Related Search