Home

Samsung UN26EH4000M User Manual

1. You can attach your TV to your LAN by connecting the LAN port on the back of your TV to an external modem using a LAN cable See the diagram below The position of port may differ depending on the model TV Rear Panel External Modem The Modem Port on the Wall ADSL VDSL Cable TV LAN Cable Modem Cable English You can attach your TV to your LAN by connecting the LAN port on the back of your TV to a IP Sharer which is connected to an external modem Use LAN cable for the connection See the diagram below TV Rear Panel The Modem Port on the Wall External Modem IP Sharer ADSL VDSL Cable TV having DHCP server LAN Cable Modem Cable LAN Cable English Depending on how your network is configured you may be able to attach your TV to your LAN by connecting the LAN port on the back of your TV directly to a network wall outlet using a LAN cable See the diagram below Note that the wall outlet is attached to a modem or router elsewhere in your house TV Rear Panel The LAN Port on the Wall LAN Cable e f your network requires a Dynamic IP address you should use an ADSL modem or router that supports Dynamic Host Configuration Protocol DHCP English Modems and routers that support DHCP automatically provide the IP address subnet mask gateway and DNS values your TV needs to access the Internet so you do not have to enter them manually Most home netw
2. Your television has several setting options for picture quality control NOTE When connecting a PC you can only make changes to Backlight Cell Light CAD Contrast Brightness and Sharpness e Settings can be adjusted and stored for each external device connected gt to the TV Lowering picture brightness reduces power consumption English M Screen Adjustment Set the various picture options such as picture size and aspect ratio e Picture Size Your cable box satellite receiver may have its own set of screen sizes as well However we highly recommend you use 16 9 mode most of the time 16 9 Sets the picture to 16 9 wide mode Wide Zoom Magnifies the picture size more than 4 3 Adjusts the Position by using A VW buttons in the Position screen Zoom Magnifies the 16 9 wide pictures vertically to fit the screen size p Adjusts the position or size by using A W buttons in the Zoom Position screen English 4 3 Sets the picture to basic 4 3 mode Do not watch in 4 3 format for a long time Traces of borders displayed on the left right and center of the screen may cause image retention screen burn which are not covered by the warranty Screen Fit Displays the full image without any cut off when HDMI 720p 10801 1080p or Component 1080 1080p signals are input Not available for PDP 450 series Smart View 1 Qe Reduces original screen by 50 Smart View 2 QR Reduces original screen by 25
3. The Now amp Next guide shows daily TV program information for each channel according to the broadcasting time Scroll lt gt to view information for a desired program while watching the current channel Scroll A V to view information for other channels If you want to move to the currently selected channel press the ENTER C button A CAMPEONATO BRASILEIRO HD Clr ana urn Mult Fri 1 Jan 7 00 pm HE AAC A Infomation It may differ depending on the model English LI Using Channel menu MENU I Support Contents Home ENTER C Press the CONTENT button to select Contents Home then select the desired menu Each screen will be displayed D Guide AllShare Play Schedule Manager Source 5 Return The displayed image may differ depending on the model English E Channel List You can view channel information All TV Analog or Favorites 1 5 When you press the CH LIST button on the remote control Channel List screen will be displayed at once All Shows all currently available channels TV Shows all currently available TV channels Analog Shows all currently available analog channels Favorites 1 5 Show all favorite channels lt Favorites 1 5 will be displayed when you set Edit Favorites If you want to view favorites channels you added press the CH LIST button and use 4 gt CH Mode button to move Favorites 1 5 English Using the function buttons with
4. When Speaker Select is set to External Speaker you should use these settings e TV Speaker Off External Speaker On When Speaker Select is set to TV Speaker you should use these settings e TV Speaker On External Speaker On K If there is no video signal both speakers will be mute English e Auto Volume Off Normal Night To equalize the volume level on each channel set to Normal Night This mode provides an improved sound experience compared to Normal mode making almost no noise It is useful at night To use the volume control on the source device connected to the TV set Auto Volume to Off on the TV Otherwise a change to the volume control of the source device may not be applied English E Reset Sound Yes No Reset all sound settings to the factory defaults English LJ Selecting the Sound Mode When you set to Dual l ll the current sound mode is displayed on the screen Audio Type Default Pero moo Automatic change Dual gt Dual Dual O we wo Automatic change gt NICAM Stereo Mono Dual If the stereo signal is weak and an automatic switching occurs then switch to the mono Only activated in stereo sound signal Only available when the Source is set to TV English LI Connecting to the Network For LED TVs network function is not supported depending on the country E Wired Network Connection You can attach your TV to your LAN using cable in three ways
5. Press the TOOLS button in Channel List screen then select the Edit Mode A check box appears to the left of the channel 2 Press the A V buttons to select the desired channel and then press ENTERL4 button The v mark indicates the channel you ve selected You can select more than one channel Press ENTERL button again to deselect the channel English 3 Press the TOOLS button then select a function and change its settings e Edit Favorites Set the selected channels you watch frequently as favorites The Edit Favorites screen has five groups Favorites 1 Favorites 2 etc You can add a favorite channel to any one of the groups Press the A V buttons to select a group Lock Unlock Lock a channel so that the channel cannot be selected and viewed This function is available only when the Channel Lock is set to On gt The PIN input screen appears Enter your 4 digit PIN the default of which is 0 0 0 0 Change the PIN using the Change PIN option English Delete Delete a channel from the channel list Information Displays details of the selected program Press the Watch to switch the channel directly Deselect Deselect the selected channels Select All Select all the channels in the channel list English E Guide The EPG Electronic Program Guide information is provided by broadcasters Using program schedules provided by broadcasters you can specify programs you want to watch in advance so tha
6. Balance Off On Giese Controls the white balance in 10 point interval by adjusting the red green and blue brightness Available when the picture mode is set to Movie and when the external input is set to all input Some external devices may not support this function Interval Select interval to adjust Red Adjust the red level Green Adjust the green level Blue Adjust the blue level Reset Resets the 10p White Balance to its default settings English e Gamma Adjust the primary color intensity e Expert Pattern Off Pattern 1 Pattern 2 ISR By running the Expert Pattern function the picture can be calibrated without a generator or filter If the OSD menu disappears or a menu other than the Picture menu is opened the calibration is saved and the Expert Pattern window disappears While the Expert Pattern is running sound is not output Only available in Standard mode Only enabled on DTV Component HDMI English e xvYCC Off On Qa Setting the xvYCC mode on increases detail and color space when watching movies from an external device e g DVD player connected to the HDMI or Component IN jacks Available when the picture mode is set to Movie and when the external input is set to HDMI or Component Some external devices may not support this function Motion Lighting Off On Reduce power consumption by brightness control adapted motion This function is not supported in 3D mode When you
7. Choose for channels that are broadcasting in mono or if you are having difficulty receiving a stereo signal Stereo Choose for channels that are broadcasting in stereo SAP Choose to listen to the Separate Audio Program which is usually a foreign language translation Depending on the particular program being broadcast you can listen to Mono Stereo or SAP English e Audio Language digital channels only Change the default value for audio languages The available language may differ depending on the broadcast e Audio Format MPEG Dolby Digital 5 1 digital channels only When sound is emitted from both the main speaker and the audio receiver a sound echo may occur due to the decoding speed difference between the main speaker and the audio receiver In this case use the TV Speaker function Audio Format option may differ depending on the broadcast 5 1 Channel digital sound is only available when connecting an external speaker through an optical cable English E Additional Settings digital channels only e DTV Audio Level MPEG HE AAC This function allows you to reduce the disparity of a voice signal which is one of the signals received during a digital TV broadcast to a desired level According to the type of broadcast signal MPEG HE AAC can be adjusted between 10dB and OaB To increase or decrease the volume adjust between the range O and 10 respectively English SPDIF Output SPDIF So
8. Delete Deletes the devices from the list This function only deletes the name of the devices from the list If the gt deleted device is turned on or tries to connect to the TV it may appear on the list again English L Troubleshooting If the TV seems to have a problem first try this list of possible problems and solutions If none of these troubleshooting tips apply visit samsung com then click on Support or call Samsung customer service Issues Solutions and Explanations Poor picture First of all please perform the Picture Test and confirm that your TV is properly displaying the test image e goto MENU Support Self Diagnosis Picture Test If the test image is properly displayed the poor picture may be caused by the source or signal English Issues The TV image does not look as good as it did in the store Solutions and Explanations If you have an analog Cable Set top box upgrade to a digital set top box Use HDMI or Component cables to deliver HD high definition picture quality Cable Satellite subscribers Try HD stations from the channel line up Air Cable Antenna connection Try HD stations after performing Auto tuning Many HD channels are up scaled from SD Standard Definition contents Adjust the Cable Set top box video output resolution to 1080i or T200 English Issues The picture is distorted macroblock error small block dots pixelization Color is wrong or mi
9. NOTE e Smart View 1 is enabled only in HDMI mode e Smart View 2 is enabled only in DTV and HDMI modes The picture size can vary depending on the input resolution when content is played using Videos under Media Play English e Position Adjust the picture position It is only available in Screen Fit or Wide Zoom e Zoom Position Adjust the picture position It is only available in Zoom NOTE e After selecting Screen Fit in HDMI 1080i 1 O80p or Component 1080i 1080p mode you may need to center the picture Select Position then follow the steps below in the Position screen Select the Position press the ENTER L button 2 Pressthe A V lt or gt button to move the picture 3 Press the ENTERL button If you want to reset the position you adjusted select Reset in the Position screen The picture will be set to its default position Depending on the input source the picture size options may vary h English The available items may differ depending on the selected mode e When connecting a PC only 16 9 and 4 3 modes can be adjusted e Settings can be adjusted and stored for each external device connected to an input on the TV e lf you use the Screen Fit function with HDMI 720p input 1 line will be cut at the top bottom left and right as in the overscan function Input Source Picture Size ATV AV 16 9 Wide Zoom Zoom 4 3 DTV 720p 16 9 Wide Zoom Zoom 4 3 Component 480i 48
10. Operation Turns the 3D function off 2D 3D Changes a 2D image to 3D w Side by Side Displays two images next to each other B Top amp Bottom Displays one image above another English Some file format may not be supported the 2D 3D When you watch 3D images under flickering lighting such as a fluorescent lamp 50Hz 60Hz or a 3 wavelength lamp you may notice some screen flickering If this occurs dim or turn off the light 3D Perspective 5 5 Adjust overall 3D perspective of on screen image e Depth 1 10 Adjust overall depth e L R Change L R Image R L Image Swap the left and right pictures English Support resolution 16 9 only e HDMI Source Resolution Frequency Hz 1280 x 720p 59 94 60 Hz sant 4920 x 1080 59 94 60 Hz gt English Components amp DTV Source Resolution Frequency Hz 1280 x 720p 59 94 60 Hz Components 1920 x 1080i 59 94 60 Hz 1920 x 1080p 23 98 24 29 97 30 59 94 60 Hz 1280 x 720p 59 94 60 Hz 1920 x 1080i 59 94 60 Hz lt e Videos Photos In AllShare Play Refer to Supported Subtitle and AllShare Play file formats in the Other Information section English How to watch the 3D image e Method 1 Some 3D modes may not be available depending on the format of the image source Z To watch in 3D wear 3D Active Glasses and press the power button on the glasses 1 Press the MENU button on your remote use the A
11. desired Music in the file list 2 Press the ENTERL button or gt Play button You can use lt lt REW and gt gt FF buttons during playback Only displays the files with supported music file extension Other file extensions are not displayed even if they are saved on the same USB device If the sound Is abnormal when playing music files adjust the Equalizer in the Sound menu An over modulated music file may cause a sound problem lt English Using the playback menu Press the lt gt button to select the desired menu e Play Pause You can start or stop a music Alternatively the gt or Lit button on the remote e Repeat Mode Off One Song All You can play music files repeatedly Shuffle Mode Off On You can play the music randomly e Sound Mode Standard Music Movie Clear Voice Amplify You can adjust the sound setting English Supported Music Formats File Extension Type Codec ee Layer 3 e mac FLAC Seeks not supported Supports up to 20h ogg OGG Voros Supports up to 2oh WMA 10 Pro supports up to 5 1 channel and M2 profile LBR mode of MO is not supported English _ Media Contents Additional Functions Playing the selected Videos Music Photos files 1 2 Press the TOOLS button at each main screen and select Selection Play Select the desired files The check box appears to the left of the selected files Press the
12. its playing time If video time information is unknown play time and progress bar are not displayed During video playback you can search using lt and gt button You can use lt REW and gt gt FF buttons during playback In this mode you can enjoy movie clips contained on a Game but you cannot play the Game itself English Supported Subtitle Formats External NEIG File extension MPEG 4 timed text SAMI SubRip txt m 3 SubViewer Sub Micro DVD Sub or txt SubStation Alpha S Advanced SubStation Alpha Powerdivx sb a y a 09 S nternal NETE Container Format English Supported Video Formats File Extension Container Video Codec DivX 3 11 4 x 5 x 6 x MPEG4 SP ASP H 264 BP MP HP Motion JPEG 640 x 480 Window Meda Media Video v9 OOo o MPEG 1 Resolution 1920 x 1080 1920 x 1080 English Frame rate fps Bit rate Mbps Audio Codec AC3 LPCM ADPCM IMA MS AAC HE AAC WMA DD MPEG MP3 DTS Core G 711 A Law u Law Other Restrictions Video content will not play or not play correctly if there is an error in the content or the container Sound or video may not work if the contents have a standard bit rate frame rate above the compatible Frame sec listed in the table seen on last page e f the Index Table is in error the Seek Jump function is not supported When playing the video through
13. or W button to select Picture and then press the ENTERL button 2 Usethe A or V button to select 3D and then press the ENTERL button English 3 Usethe A or V button to select 3D Mode and then press the ENTERLC4 button 4 Using the lt or gt buttons on your remote control select the 3D Mode of the image you want to view e Method 2 1 Press the button on your remote and then you can view the 3D image 2 Ifyou want to change 3D options such as 3D Perspective press the MENU button on your remote and then select Picture 3 Goto Step 3 in the Method 1 and follow the directions from that point on To exit the 3D mode press the gig button on your remote again English Before using 3D function NOTE 3D Mode is set to Off automatically when you access AllShare Play or e Manual functions 3D Mode is set to memorized configuration value automatically when Changing the input source Some Picture functions are disabled in 3D mode PIP is not supported in 3D mode 3D Active Glasses from Samsung s previous product IR type or other manufacturers not be supported When the TV is initially powered on may take some time until the 3D display is optimized English The 3D Active Glasses may not work properly if there is any other 3D product or electronic devices turned on near the glasses or TV If there is a problem keep other electronic devices as far away as possible from the 3D Active Gl
14. router modem or device is not certified it may not connect to the TV via the Samsung Wireless LAN Adapter Ensure the TV is turned off before you connect the Samsung Wireless LAN Adapter Connection Methods You can setup the wireless network connection like below Auto Setup Using the Auto Network Search function Manual Setup WPS PBC Wi Fi Direct The Samsung Wireless LAN Adapter may not be recognized when using a connection via a USB hub or via a USB extension cable other than the cable supplied English Notice The picture may appear corrupted or have static for some channels when the TV is connected to the Samsung Wireless LAN Adapter In such a case establish a connection using one of the following methods or connect the Samsung Wireless LAN Adapter using a USB cable in a place that is not affected by radio interference Connect using the USB right angle adapter To connect the Samsung Wireless LAN Adapter using the USB right angle adapter follow these steps 1 Connect the USB right angle adapter to the Samsung Wireless LAN Adapter B The position of port may differ 2 Connect the other end of the right angle depending on the model adapter to the USB port English Connect via an extension cable To reconnect the Samsung Wireless LAN Adapter using the extension cable follow these steps 1 Connect the extension cable to the USB port 2 Connect the extension cable an
15. slot is beside the R icon The position and color may differ depending on the model To lock the product follow these steps 1 Wrap the Kensington lock cable around a large stationary object such as desk or chair Optional English RQ A Slide the end of the cable with the lock attached through the looped end of the Kensington lock cable Insert the locking device into the Kensington slot on the product Lock the lock NOTE These are general instructions For exact instructions see the User manual supplied with the locking device The locking device has to be purchased separately The location of the Kensington slot may be different depending on the TV gt model English _ License Sf S TheaterSound SRS and symbol are trademarks of SRS Labs Inc TheaterSound technology is incorporated under license from SRS Labs Inc TheaterSound SRS TheaterSound provides the most immersive surround sound experience from the TVs built in speakers while maintaining steady volume and delivering rich bass and clear dialog X DOLBY Manufactured under license from Dolby Laboratories Dolby and the ATT double D symbol are trademarks of Dolby Laboratories Manufactured under license under U S Patent Nos 5 956 674 S dts 5 974 380 6 487 535 amp other U S and worldwide patents issued 2 0 Digital Out amp pending DTS the Symbol amp DTS and the Symbol together
16. 0p 576i 576p 720p 16 9 Wide Zoom Zoom 4 3 DTV 1080i 1080p 16 9 Wide Zoom Zoom 4 3 Screen Fit Smart View 2 Component 1080i 1080p 16 9 Wide Zoom Zoom 4 3 Screen Fit HDMI 720p 1080i 1080p 16 9 Wide Zoom Zoom 4 3 Screen Fit Smart View 1 Smart View 2 English L Changing the Picture Options E Advanced Settings MENU MI Picture Advanced Settings ENTERC available in Standard Movie mode e Dynamic Contrast Off Low Medium Advanced Settings High Adjust the screen contrast e Black Tone Off Dark Darker Darkest Black Tone Select the black level to adjust the screen depth Flesh Tone Emphasize pink Flesh Tone e RGB Only Mode Off Red Green Blue pio Displays the Red Green and Blue color Top White Balance for making fine adjustments to the hue and l The displayed image may differ saturation depending on the model English e Color Space Auto Native Custom iglesias Adjust the range of colors available to create the image To adjust Color Red Green Blue and Reset set Color Space to Custom White Balance Adjust the color temperature for a more natural picture R Offset G Offset B Offset Adjust each color s red green blue darkness R Gain G Gain B Gain Adjust each color s red green blue brightness Reset Resets the White Balance to its default settings English e 10p White
17. E MANUAL imagine the possibilities Thank you for purchasing this Samsung product To receive more complete service please register your product at www samsung com register Model Serial No Contents Channel Using the INFO button Now amp Next guide Using Channel menu Memorizing channels Other Features Basic Features Changing the Preset Picture Mode Adjusting Picture Settings Changing the Picture Options Changing the Preset Sound Mode Sound Settings Adjusting Sound Settings Selecting the Sound Mode 16 19 21 22 27 37 38 40 48 Preference Features Connecting to the Network Setting the Wired Network Setting the Wireless Network Managing the Network Connected Devices Setting the Setup Setting the Time Using the Sleep Timer Setting the On Off Timer Locking Programs Picture In Picture PIP Economical Solutions Other Features Support Menu 49 66 70 TT 81 82 84 85 89 91 93 95 106 Advanced Features e Using the 3D function e Using the Media Contents e Connecting a USB Device e Connecting to the PC through network e Screen Display e Media Contents Additional Functions e Using the DLNA Functions Other Information e Troubleshooting e Anti theft Kensington Lock e License 116 127 128 134 137 148 153 159 175 177 LJ Using the INFO button Now amp Next guide The display identifies the current channel and the status of certain audio video settings
18. Setup procedure Press the SOURCE button to select TV mode go to MENU System Setup gt ENTER Check the cable connections and reconnect them Loss of audio or video can be caused by using overly rigid or thick cables Make sure the cables are flexible enough for long term use If mounting the TV to the wall we recommend using cables with 90 degree connectors English Issues Solutions and Explanations The PIP menu is not e PIP functionality is only available when you are using a HDMI or available components source You see small particles e This is part of the product s design and is not a defect when you look closely at the edge of the frame of the TV POP TV s internal banner e Select Home Use under Setup mode For details refer to Setup ad appears on the Initial Setup screen The message This file e This may appear because of high bit rate of content Content may not be playable generally will play but could experience some playability issue properly appears English L Anti theft Kensington Lock The Kensington Lock is not supplied by Samsung It is a device used to physically fix the system when using it in a public place The appearance and locking method may differ from the illustration depending on the manufacturer Refer to the manual provided with the Kensington Lock for additional information on proper use Please find a R icon on the rear of the TV A kensington
19. am when digital channel is selected English e Edit Favorites Ga Set channels you watch frequently as favorites Add or delete the selected channel in Favorites 1 5 1 Select the Edit Favorites then press the ENTER L button 2 Press the ENTERL4 button to select Favorites 1 5 then press the OK button One favorites channel can be added in several of favorites among Favorites 1 5 Lock Unlock Lock a channel so that the channel cannot be selected and viewed This function is available only when the Channel Lock is set to On The PIN input screen appears Enter your 4 digit PIN the default of which is 0 0 0 0 Change the PIN using the Change PIN option English Channel Name Edit analog channels only Assign your own channel name Edit Channel Number digital channels only Edit the number by pressing the number buttons desired Delete Delete a channel from the channel list Information Displays details of the selected program Press the Watch to switch the channel directly Sort digital channels only Changes the list ordered by channel number or channel name Change Antenna Switches to Air or Cable Edit Mode You can select desired channels and edit it For detailed information about using Edit Mode refer to Using Option Menu in Edit Mode English Using Option Menu in Edit Mode Set each channel using the menu options Edit Favorites Lock Unlock Delete Information Deselect Select All 1
20. are registered trademarks amp DTS 2 0 Digital Out is a trademark of DTS Inc Product includes software DTS Inc All Rights Reserved English The terms HDMI and HDMI High Definition Multimedia Interface and the HDMI Hm Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries DI WX DivX Certified to play DivX video up to HD 1080p including HD premium content ABOUT DIVX VIDEO DivX is a digital video format created by DivX LLC a subsidiary of Rovi Corporation This is an official DivX Certified device that plays DivX video Visit divx com for more information and software tools to convert your files into DivX videos ABOUT DIVX VIDEO ON DEMAND This DivX Certified device must be registered in order to play purchased DivX Video on Demand VOD movies To obtain your registration code locate the DivX VOD section in your device setup menu Go to vod divx com for more information on how to complete your registration Covered by one or more of the following U S patents 7 295 673 7 460 668 7 515 710 7 519 274 DivX DivX Certified and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license Open Source License Notice In the case of using open source software Open Source Licenses are available on the product menu Open Source License Notice is written only English English
21. asses Be sure to stay within the viewing angle and optimum TV viewing distance when watching 3D pictures Otherwise you may not be able to enjoy proper 3D effects The ideal viewing distance should be three times or more the height of the screen We recommend sitting with viewer s eyes on a level with the screen English LI Using the Media Contents Enjoy photos music and movie files saved on a USB Mass Storage Class MSC device 1 Press the CONTENT button to select Media Play AllShare Play CERES 2 Press A V button to select desired menu Videos Photos Music then press the ENTER button The displayed image may differ depending on the model 3 Press A V button to select desired device then press the ENTER L button again 5 Return English LI Connecting a USB Device 1 Turn on your TV TV Side Panel 2 Connect a USB device containing photo music and movie files to the USB port on the side of the TV 3 When USB is connected to the TV popup window appears You can select the Videos Photos or Music directly i a may lt It might not work properly with unlicensed multimedia files English Need to Know List before using Media Contents MTP Media Transfer Protocol is not supported The file system supports NTFS Read Only FAT16 and FAT32 Certain types of USB Digital camera and audio devices may not be compatible with this TV Media Contents only supports USB Mass S
22. button to select Play then press the ENTERC button You can select or deselect all files pressing the Select All Deselect All English Videos Music Photos Play Option menu During playing a file press the TOOLS button Category Operation Videos Photos Music Title Search You can move the other file directly vs You can search the video using lt and gt button at one minute interval or Time Search entering the number directly J It may not be supported depending on the input source Repeat Mode You can play movie files repeatedly Py fof gt preference English Category Operation Videos Photos Music Picture Mode You can adjust the picture setting Pov fo vw fo Sound Mode You can adjust the sound setting Pov f vw fo You can change the audio language if eyo EaR the video has more than one language jx Subtitle You can set subtitles on off You can play the video with subtitles Subtitle Settings This function only works if the subtitles vV are the same file name as the video Start Slide Show Stop Slide Show You can start or stop a slide show Pf fe English Category Operation Videos Photos Music You can select the slide show speed PACKIrOUNA MUSIC You can set on off background music On Background v when watching a slide show Music Off Background Music You can select background music VY Setting when watching a slide show screen mode English Category Rotate Edit Playl
23. cally USB can be selected only when a USB device is connected to the TV Antenna when the Source is set to TV Select the desired broadcasting signal Channel when the Source is set to TV Select the desired channel Music Photo when the Source is set to USB Select a folder in the USB device containing music or photo files to be played when the TV is turned on automatically gt If there is no music file on the USB device or the folder containing a music file is not selected the Timer function does not operate correctly When there is only one photo file in the USB the Slide Show will not play English A folder with too long of a name cannot be selected Each USB you use is assigned its own folder When using more than one of the same type of USB make sure the folders assigned to each USB have different names It is recommended that you use a USB memory stick and a multi card reader when using On Timer The On Timer function may not work with USB devices with a built in battery MP3 players or PMPs made by some manufacturers because these devices take a long time to be recognized English e Off Timer Three different off timer settings can be made You must set the clock first Setup Select Off Once Everyday Mon Fri Mon Sat Sat Sun or Manual to set at your convenience If you select Manual you can set up the day you want to activate the timer The Y mark indicates the day you ve selected Time Set t
24. ce that is connected to the TV i e an Air or a Cable system English E Auto Tuning Scans for a channel automatically and stores in the TV Automatically allocated program numbers may not correspond to actual or desired program numbers If a channel is locked the PIN input window appears If the antenna is connected to ANT 2 IN CABLE select Cable and if it is connected to ANT 1 IN AIR select Air When Antenna Source is set to Air or Cable When selecting Air Provide a value to scan for Digital and Analog channels When selecting Cable Provide a value to scan for Analog channels Analog Cable System Select the Analog Cable System among STD HRC and IRC by pressing the A or V button then press the Next English E Digital Manual Tuning Scans for a digital channel manually and stores in the TV Press the New button to search the digital channels by adjusting the Channel or Frequency If a channel is locked the PIN input window appears Digital Manual Tuning is only available in digital TV mode Channel Set the channel number using the A VW or number O 9 buttons Frequency Set the frequency using the number buttons E Channel Add Delete analog channels only You can delete or add a channel to display the channels you want This function is only available in the Tools menu English Q Other Features E Fine Tune analog channels only If the reception is clear you do not have to fine tune th
25. change the Backlight Cell Light CDAD Contrast or Brightness the TV sets Motion Lighting to Off Only available in Standard mode English E Picture Options MENU I Picture Picture Options ENTERC When connecting a PC you can only make changes to the Color Tone e Color Tone Cool Standard Warm1 Warm2 SS Warm1 or Warm2 will be deactivated when Digital Noise Filter the picture mode is Dynamic issih Settings can be adjusted and stored for Picture Options Film Mode Off each external device connected to an input Auto Motion Plus Standard on the TV LED Motion Plus Off The displayed image may differ depending on the model English Digital Noise Filter Off Low Medium High Auto Auto Visualization If the broadcast signal received by your TV is weak you can activate the Digital Noise Filter feature to reduce any static and ghosting that may appear on the screen When the signal is weak try other options until the best picture is displayed Auto Visualization When changing analog channels displays signal strength Only available for analog channels When the INFO button is pressed the signal strength bar is displayed When bar is green you are receiving the best possible signal e MPEG Noise Filter Off Low Medium High Auto Reduces MPEG noise to provide an improved picture quality English e HDMI Black Level Low Normal Selects the black level on the screen to a
26. d Samsung co Wireless LAN Adapter oS ae The position of port may differ 3 Attach the Samsung Wireless LAN Adapter to depending on the model the back of the TV near the top using double sided adhesive tape The Samsung Wireless LAN Adapter should be installed in an interference free area in order to avoid interference between the adapter and tuner English E Network Settings MENU Network Network Settings ENTER C Set the network connection to use AllShare Play and perform software upgrade For detailed settings for wired network refer to the Setting the Wired Network and for detailed settings for wireless network refer to the Setting the Wireless Network in this manual English M Network Status MENU Network Network Status ENTERL You can check the current network and Internet status English The check list for wired network connection failure When wired network connection failed try to apply the following information to each issue Issues Solutions and Explanations No network cable found Check that your network cable is plugged in e fitis connected make sure that the router is turned on if it is on try turning it off and on again IP auto setting failed Try the following to set your IP address automatically or set your IP address manually by selecting IP Settings e Ensure DHCP server is enabled on router and unplug and re plug in the router e Contact your In
27. devices 1 Connect the mobile phone or other devices which support AllShare Play function and then play the media contents of each device The popup screen appears on the bottom of your TV 2 Select the Allow to accept the connected devices The media contents of the devices can be playing on your TV You can find the allowed devices on the AllShare Settings English Using the AllShare Play function play the media contents of the devices connected to DLNA function 1 2 Press the CONTENT button to select AllShare Play Press A V button to select desired menu Videos Photos Music then press the ENTER LC button When the DLNA device is selected press the ENTERL button again Press the lt A V button to select the desired file Press the ENTER L button English NOTE Contents may not be played on your TV depending on their resolution and format e The ENTERL and lt P buttons may not work depending on the type of media content e Using the mobile device you can control the media playing For details refer to each mobile s user s guide English Using the AllShare Settings function MENU Network AllShare Settings ENTERC Shows a list of mobile phones or connected devices which have been set up with this TV for using the AllShare Settings function The AllShare Settings function is available in all devices which support DLNA DMC e Allow Deny Allows Blocks the devices e
28. djust the screen depth Available only in HDMI mode RGB signals e Film Mode Off Auto1 Auto2 Sets the TV to automatically sense and process film signals from all sources and adjusts the picture for optimum quality Available in TV AV COMPONENT 480i 1080 and HDMI 1080 If the screen does not seem natural change its option to Off Auto1 Auto2 in Film Mode English e Auto Motion Plus Off Clear Standard Smooth Custom Demo Enhances motion in fast moving scenes The info screen on your TV displays the resolution and frequency of the incoming video signal 60Hz This displayed frequency is not what the TV is displaying by using the Auto Motion Plus function If noise occurs on the screen please set up the Auto Motion Plus to Off If Auto Motion Plus is Custom you can set up the Blur Reduction Judder Reduction or Reset manually Blur Reduction Adjust blur reduction level of video sources Judder Reduction Adjust judder reduction level of video sources with film gt signals Reset Restore settings to default values e LED Motion Plus Off On Removes drag from fast scenes with a lot of movement to provide a clear picture English mM Reset Picture Yes No Resets your current picture mode to its default settings English L Changing the Preset Sound Mode MENU I Sound Sound Mode ENTERC Sound Mode Standard Selects the normal sound mode Music Emphasize
29. during the software transmission period software will be automatically searched and downloaded The time required to download the software is determined by the signal status e Alternative Software Replace the current software with the alternative English Standby Mode Upgrade Off 1 hour later 2 hours later 12 00 am 02 00 am 12 00 pm 02 00 pm A manual upgrade will be automatically performed at selected time Since the power of the unit is turned on internally the screen may be turned on slightly for the product This phenomenon may continue for more than 1 hour until the software upgrade is complete English E Contact Samsung View this information when your TV does not work properly or when you want to upgrade the software You can find information regarding our call centers and how to download products and software English E Contents Home You can enjoy useful and various contents English LJ Using the 3D function 3D MENU Picture 3D ENTER Q This exciting new feature enables you to view 3D content To fully enjoy this feature you must purchase a pair of Samsung 3D Active Glasses to view 3D video Samsung 3D Active Glasses are sold separately For more detailed purchasing information contact the retailer where you purchased this TV Z Full HD 3D Glasses Logo indicates compatibility between display products and 3D Glasses which are compliant with the Full HD 3D Glasses format a
30. e user the screen saver is activated to prevent the formation of ghost images on the screen Scrolling This function removes after images on the screen by moving all the pixels on the PDP according to a pattern Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time English The after image removal function has to be executed for a long time approximately 1 hour to effectively remove after images on the screen If the after image is not removed after performing the function repeat the function again Press any key on the remote control to cancel this feature Side Gray Light Dark When you watch TV with the screen ratio set to 4 3 the screen is prevented from any damage by adjusting the white balance on both extreme left and right sides English E General e Game Mode Off On When connecting to a game console such as PlayStation or Xbox you can enjoy a more realistic gaming experience selecting the game menu NOTE Precautions and limitations for game mode To disconnect the game console and connect another external device set Game Mode to Off in the setup menu f you display the TV menu in Game Mode the screen shakes slightly English e Game Mode is not available when the input source is set to TV e After connecting the game console set Game Mode to On Unfortunately you may notic
31. e channel as this is done automatically during the search and store operation If the signal is weak or distorted fine tune the channel manually e Select Fine Tune in the Channel menu Fine tuned channels that have been saved are marked with an asterisk on the right side of the channel number in the channel banner To reset the fine tuning select Reset lt gt English E Crosstalk Noise Reduction Off On analog channels only Reduce diagonal noise in picture caused by the crosstalk of signals E Color System Auto PAL M PAL N NTSC analog channels only Normally the TV can receive image and sound with good quality in Auto mode This mode detects the color signal sources automatically If the color implementation is unsatisfactory select any of PAL M PAL N or NTSC English L Changing the Preset Picture Mode MENU I Picture Picture Mode ENTER E Picture Mode Select your preferred picture type When connecting a PC you can only make changes to the Entertain and Standard Dynamic Suitable for a bright room Standard Suitable for a normal environment Natural IESE Suitable for an eye comfortable display Movie Suitable for watching movies in a dark room Entertain Suitable for watching movies and games It is only available when connecting a PC English L Adjusting Picture Settings E Backlight Cell Light Contrast Brightness Sharpness Color Tint G R
32. e reduced picture quality e f Game Mode is On Picture Mode is set to Standard and Sound Mode is set to Movie English Panel Lock Off On Lock or unlock all the keys on the panel e Boot Logo Off On Display Samsung logo when the TV is turned on e AV Color System Auto PAL M PAL N NTSC Normally the TV can receive image and sound with good quality when in the mode Auto This mode detects the signal color system automatically In case of some signal reception with color unsatisfactory select the AV Color System Mode to PAL M PAL N or NTSC English E DivX Video On Demand Shows the registration code authorized for the TV If you connect to the Divx web site and register with 10 digit registration code you can download the VOD activation file Once you play it using Media Play the registration is completed For more information on DivX VOD visit htto vod divx com English LI Support Menu MENU I Support gt ENTERC E e Manual You can read the introduction and instructions about the TV features stored in your TV For the detailed information about e Manual Screen refer to How to view the e Manual in User Manual English E Self Diagnosis e Picture Test Yes No Use to check for picture problems If the problem continues to occur check the color pattern Yes If the test picture does not appear or there is noise in the test picture select Yes There may be a probl
33. ed to enter a security key to use the router Contact your Internet Service Provider for more information English Issues Unable to connect to the network Connected to your local network but cannot connect to the Internet Network setup complete but cannot connect to the Internet Solutions and Explanations Check if your IP address is set correctly in IP Settings Check if you need to enter a security key to use the router Contact your Internet Service Provider for more information Check your Internet LAN cable is connected correctly to LAN port of router Check the DNS settings in IP Settings If the problem persists contact your Internet Service Provider to access the Internet Log in Internet service network If the problem persists contact your Internet Service Provider to access the Internet English LI Setting the Wired Network E Wired Network Setup Auto When connecting the LAN Cable the screen pop up appears directly to set wired network Use the Automatic Network Setup when connecting your TV to a network that supports DHCP To set up your TV s cable network connection automatically follow these steps English How to set up automatically 1 Goto Network Settings screen Network Network Settings 2 Select Start 3 The network connection screen appears and network setting is done Network cable connected Press Start to configure your wired netw
34. em with the TV Contact Samsung s Call Center for assistance No If the test picture is properly displayed select No There may be a problem with your external equipment Please check your connections If the problem persists refer to the external device s user manual English e Sound Test Yes No Use the built in melody sound to check for sound problems If you hear no sound from the TV s speakers before performing the sound test make sure Speaker Select is set to TV Speaker in the Sound menu The melody will be heard during the test even if Speaker Select is set to External Speaker or the sound is muted by pressing the MUTE button Yes If you can hear sound only from one speaker or not at all during the sound test select Yes There may be a problem with the TV Contact Samsunqg s Call Center for assistance No If you can hear sound from the speakers select No There may be a problem with your external equipment Please check your connections If the problem persists refer to the external device s user manual English Signal Information digital channels only An HD channel s reception quality is either perfect or the channels are unavailable Adjust your antenna to increase signal strength e Reset Reset all settings to the factory defaults except network settings The PIN input screen appears before the setup screen Enter your 4 digit PIN Change the PIN using the Change PIN option Troubleshooti
35. en displaying up scaled SD 4 3 contents Black bars on Top amp Bottom will be shown on movies that have aspect ratios different from your TV Adjust picture size option on your external device or TV to full screen English Issues Plasma TV is making humming noise 0da D Sma Image Retention Burn In Issue Gan Saas Solutions and Explanations Plasma TVs typically make a soft humming sound This is normal It s caused by the electrical charges that are used to create the images on the screen If the humming sound is loud you may have set the brightness on the TV too high Try setting the brightness lower You can also have loud humming if the back of your Plasma TV is too close to a wall or other hard surface Also try rerouting your connection cables Improper installation of wall mount can create excessive noise To minimize the possibility of screen burn this unit is equipped with Pixel Shift screen burn reduction technology Pixel Shift lets you set the picture so it moves slightly up and down Vertical Line and side to side Horizontal Dot The regular slight movement of the picture reduces screen burn in English Issues The remote control does not work The cable set top box remote control does not turn the TV on or off or adjust the volume A Mode Not Supported message appears Caption on TV menu is greyed out Solutions and Explanations Replace the remote contr
36. evice lt q If you want to disconnect the device select the connected device and press gt the ENTERL button to select Disconnect English E AllShare Settings MENU Network AllShare Settings ENTER C Set whether to allow a network connected device like a smartphone or tablet to share content or control TV using an application downloaded on your mobile device For details on set up options refer to the Using the DLNA Functions English E Device Name MENU Network Device Name ENTER C Change the TV s name by keying in a name manually A keyboard appears on the screen and you can key in a name for your TV manually using your remote control For example if you want to change the name to Samsung TV press each character using the A W lt P buttons and then select Done English 2 Setting the Setup E Setup MENU System Setup ENTER C Configure the channels and the time when setting up the TV for the first time or when resetting the unit For the detailed information about setting Setup refer to Setup Initial Setup in User Manual lt j Enter your 4 digit PIN the default of which is 0 O 0 0 English LI Setting the Time E Time MENU I System Time ENTER The current time will appear every time you press the INFO button Clock Setting the clock is for using various timer features of the TV If you disconnect the power cord you have to set the clock a
37. gain Clock Mode Set up the current time manually or automatically Auto Set the current time automatically using the time from a digital channel The antenna must be connected in order to set the time automatically English Manual Set the current time manually Depending on the broadcast station and signal the auto time set up may not be correct In this case set the time manually Clock Set Set the Date and Time Available only when Clock Mode is set to Manual You can set the Date and Time directly by pressing the number buttons on the remote control English a Using the Sleep Timer MENU I System Time Sleep Timer ENTER C e Sleep Timer Gee Automatically shuts off the TV after a preset period of time 30 60 90 120 150 and 180 minutes To cancel the Sleep Timer select Off English LI Setting the On Off Timer MENU M System Time On Timer lt or gt Off Timer ENTERL On Timer Three different on timer settings can be made You must set the clock first Setup Select Off Once Everyday Mon Fri Mon Sat Sat Sun or Manual to set at your convenience If you select Manual you can set up the day you want to activate the timer The Y mark indicates the day you ve selected Time Set the hour minute am pm Return Volume Set the desired volume level English Source Select TV or USB content to be played when the TV is turned on automati
38. he hour minute and am pm 5 Return English _1 Locking Programs MENU System Security ENTERC M Security The PIN input screen appears before the setup screen Enter your 4 digit PIN the default of which is 0 0 0 0 Change the PIN using the Change PIN option e Channel Lock Off On Lock channels to prevent unauthorized users such as children from watching unsuitable program English e Change PIN The Change PIN screen will appear Choose any 4 digits for your PIN and enter it in the Enter New PIN Re enter the same 4 digits in the Confirm New PIN When the Confirm screen appears press the ENTERL button Your PIN has been memorized If you forget the PIN code press the remote control buttons in the following sequence in Standby mode which resets the PIN to 0 0 0 0 MUTE 8 2 4 POWER on English 2 Picture In Picture PIP MENU I System PIP ENTER Q PIP You can watch the TV tuner and one external video source simultaneously PIP Picture in Picture does not function in the same mode NOTE For PIP sound refer to the Sound Select instructions If you turn the TV off while watching in PIP mode the PIP window will disappear You may notice that the picture in the PIP window becomes slightly unnatural when you use the main screen to view a game or karaoke English e PIP Settings Main picture Sub picture PIP Off On Activate or deactivate
39. ically when connected to the TV If a USB extension cable is used the USB device may not be recognized or the files on the device may not be read If a USB device connected to the TV is not recognized the list of files on the device is corrupted or a file in the list is not played connect the USB device to the PC format the device and check the connection If a file deleted from the PC is still found when Media Contents is run use the Empty the Recycle Bin function on the PC to permanently delete the file Media Contents only supports sequential joeg format The scene search and thumbnail functions are not supported in the Videos If the number of files and folders saved on a USB storage device is approximately over 4000 the files and folders may not appear and some folders may not be opened English Disconnecting a USB Device Method 1 Using the SOURCE button 1 Press the SOURCE button 2 Select a desired USB device and then press the TOOLS button The Tools menu appears 3 Select Safely Remove USB and then wait until the selected USB device is disconnected You can remove a USB device from the TV English Method 2 Using the Media Play AllShare Play home screen 1 Go to Media Play AllShare Play home screen 2 Select any category and then press the ENTERL button 3 Select a desired USB device and then press the TOOLS button The Tools menu appears 4 Select Safely Remove USB and then wa
40. ion screen set IP Mode to Manual Press the W button to go to the first entry field Enter the IP Address Subnet Mask Gateway and DNS Server values Use the number buttons to enter numbers and the arrow buttons to move from one entry field to another When done select the OK The network connection screen appears and network setting is done English gt E Wireless Network Setup WPS PBC If your router has a WPS PBC button follow these steps 1 Goto Network Settings screen 2 Select Start 3 The Network function searches for available wireless networks When done it displays a list of the available networks Select the WPS PBC Press the WPS PBC button on your router within 2 minutes Your TV gt automatically acquires all the network setting values it needs and connects to your network 6 The network connection screen appears and network setting is done English If Your TV Fails to Connect to the Internet Your TV may not be able to connect to the Internet because your ISP has permanently registered the MAC address a unique identifying number of your PC or modem which it then authenticates each time you connect to the Internet as a way of preventing unauthorized access As your TV has a different MAC address your ISP can not authenticate its MAC address and your TV can not connect To resolve this problem ask your ISP about the procedures required to connect devices other than a PC such as
41. ist Selection Play Information Operation Videos Photos Music You can rotate images in full screen 7 mode You can edit the play list when playing Y the desired music Select and play multiple files Pf Pw You can see detailed information about English 2 Using the DLNA Functions You can play media contents including videos photos and music saved on your mobile phones or the other devices Such as your PC by controlling them on the TV via the network For more information visit www samsung com or contact the Samsung call center Mobile devices may need additional software installation For details refer to each device s user s guide If your Samsung TV connects to a non Samsung DLNA server a compatibility issue may occur during video playback gt English By connecting your Samsung TV to a network via AllShare Play you can use Samsung s original functions as follows Playback of various video formats DivX MP4 3GPP AVI ASF MKV etc Video thumbnail feature Bookmark function to resume video playback Auto chaptering scene navigation Digital content management Compatibility with various subtitle formats SRT SMI SUB TXT TTXT Search with file names And many others To use the original DLNA functions of Samsung fully it is recommended that you use the AllShare Play software provided with your TV English Playing the media contents saved on the
42. it until the selected USB device is disconnected You can remove a USB device from the TV 77 To remove a USB device from the TV we recommend use Safely d Remove USB function English LJ Connecting to the PC through network You can play pictures music and videos saved on your PC through a network connection in the AllShare Play mode over your TV If you want to use AllShare Play to play files saved on your PC over your TV you should download AllShare PC Software and users manual from www samsung com 1 For more information on how to configure your network refer to Network Connection You are recommended to locate both TV and PC in same subnet The gt first 3 parts of the IP address of the TV and PC should be the same and only the last part the host address should be changed e g IP Address 123 456 789 English 2 Using aLAN cable connect between the external modem and the PC onto which the AllShare PC Software program will be installed You can connect the TV to the PC directly without connecting it through a Sharer Router Z Functions that are not supported when connecting to a PC through a network The Background Music On and Background Music Setting functions The lt lt REW or gt gt FF button while a movie is playing The DivX DRM Multi audio embedded caption does not supported y S AllShare PC Software should be permitted by the firewall program on
43. le box please try to reset it reconnect the AC cord and wait until the cable box reboots It may take up to 20 minutes Set output resolution of the cable box to 1080i or 720p First of all please perform the Sound Test to confirm that your TV audio is properly operating go to MENU Support Self Diagnosis Sound Test If the audio is OK the sound problem may be caused by the source or signal Please check the volume of the device Cable Sat Box DVD Blu ray etc connected to your TV English Issues The picture is good but there is no sound The speakers are making an inappropriate noise Solutions and Explanations Set the Speaker Select option to TV Speaker in the Sound menu If you are using an external device check the device s audio output option ex you may need to change your cable box s audio option to HDMI when you have a HDMI connected to your TV If you are using a DVI to HDMI cable a separate audio cable is required Reboot the connected device by reconnecting the device s power cable Check the cable connections Make sure a video cable is not connected to an audio input For Antenna or Cable connections check the signal information Low signal level may cause sound distortion Perform the Sound Test as explained above English Issues No Picture No Video The TV will not turn on The TV turns off automatically Solutions and Explanations Make sure the AC p
44. ly turned off when no user operation is received for 4 hours English Q Other Features MENU I System ENTERC E Language e Menu Language Set the menu language 1 Select Menu Language and press the ENTERL button 2 Choose desired language and press the ENTERL button Choose between English Portugu s and Espanol e Preferred Language Primary Audio Secondary Audio Primary Subtitle gt Secondary Subtitle Select a language which will be the default language when a channel is selected English E Subtitle digital channels only Use this menu to set the Subtitle mode The subtitle feature does not work in Component or HDMI modes Subtitle Off On Switches subtitles on or off Subtitle Mode Normal Hearing Impaired Sets the subtitle mode Subtitle Language Sets the subtitle language If the program you are watching does not support the Hearing Impaired function Normal automatically activates even if the Hearing Impaired gt mode is selected English is the default in cases where the selected language is unavailable in the broadcast English E Caption On Screen Text Messages analog channels only e Caption Off On You can switch the caption function on or off If captions are not available they will not be displayed on the screen The Caption feature does not work in Component or HDMI modes Caption Mode You can select the desired caption mode The availability of captio
45. msung recommends using IEEE 802 11n When you play video over a network connection the video may not be played smoothly NOTE e You must use the Samsung Wireless LAN Adapter WISOQSABGNX WIS12ABGNX to use a wireless network Samsung Wireless LAN Adapter and the USB extension Cable are sold separately and are offered by select retailers and Ecommerce sites English Jo use a wireless network your TV must be connected to a wireless IP sharer either a router or a modem If the wireless IP sharer supports DHCP your TV can use a DHCP or static IP address to connect to the wireless network Select a channel for the wireless IP sharer that is not currently being used If the channel set for the wireless IP sharer is currently being used by another device nearby this will result in interference and communication failure lf you apply a security system other than the systems listed below it will not work with the TV p English e f HIGH PURE THROUGHPUT Greenfield 802 11n mode is selected and the Encryption type is set to WEP or TKIP for your wireless router Samsung TVs will not support a connection in compliance with new Wi Fi certification specifications e f your wireless router supports WPS Wi Fi Protected Setup you can connect to the network via PBC Push Button Configuration or PIN Personal Identification Number WPS will automatically configure the SSID and WPA key in either mode English If your
46. nd does not indicate picture quality of display products English Viewing TV using the 3D function IMPORTANT HEALTH AND SAFETY INFORMATION FOR 3D PICTURES Read and understand the following safety information before using the TV s 3D function A WARNING Some viewers may experience discomfort while viewing 3D TV such as dizziness nausea and headaches If you experience any such symptom stop viewing 3D TV remove 3D Active Glasses and rest e Watching 3D images for an extended period of time may cause eye strain If you feel eye strain stop viewing 3D TV remove your 3D Active Glasses and rest English A responsible adult should frequently check on children who are using the 3D function If there are any reports of tired eyes headaches dizziness or nausea have the child stop viewing 3D TV and rest e Do not use the 3D Active Glasses for other purposes Such as general eyeglasses sunglasses protective goggles etc e Do not use the 3D function or 3D Active Glasses while walking or moving around Using the 3D function or 3D Active Glasses while moving around may result in injuries due to running into objects tripping and or falling English e 3D Mode Select the 3D input format Z Ifyou want to feel the 3D effect fully please wear the 3D Active Glasses first and then select 3D Mode from the list below that provides the best 3D viewing experience When watching 3D images turn on 3D Active Glasses 3D Mode
47. nel list go to MENU Channel Auto Tuning then select Auto and make sure the correct Cable TV signal type is set in the menu Verify the Antenna is positioned correctly No Caption on digital Check Caption setup menu channels Some channels may not have caption data The picture is distorted Compression of video contents may cause picture distortion macroblock error small especially on fast moving pictures such as sports and action movies block dots pixelization A low signal can cause picture distortion This is not a TV problem English Issues Solutions and Explanations Network Connection Eod aD Eo OESS The wireless network Samsung Wireless LAN adapter is required to use a wireless connection failed network Make sure the TV is connected to a wireless IP sharer Router Software Upgrade over Try Network Settings in Network menu the network fails If you have latest SW version SW upgrade will not proceed English Issues Others Purple green rolling horizontal bars and buzzing noise from the TV speakers with Component cable connection The picture will not display in full screen Solutions and Explanations Remove the left and right audio connections from the set top box If the buzzing stops this indicates that the set top box has a grounding issue Replace the Component video cables with an HDMI connection HD channels will have black bars on either side of the screen wh
48. network it may not work depending on the network status When you play video over a network connection the video may not be played smoothly Some USB digital camera devices may not be compatible with the player e The menu can be displayed late if the video is over 10Mbps bit rate English Wife Yee erele ANEO 0R o 101010 5f Supports up to H 264 Level 4 1 WMA 10 Pro supports up to 5 1 channel H 264 FMO ASO RS VC1 SP MP and M2 profile LBR mode of MO is not AP L4 and AVCHD are not supported supported GMCis not supported WMA lossless audio is not supported English E Photos Viewing a Photo or Slide Show 1 Press the lt P A button to select the desired photo in the file list 2 Press the ENTER CC button L When you press the gt Play button in the file list slide show will be started immediately Z During the slide show all files in the file list will be displayed in order During the slide show you can adjust the slide show speed using lt lt gt REW or gt gt FF button Z You can move to other file using lt or gt button Music files can be automatically played during the slide show if the Background Music On is set English Supported Photo Formats File Extension Type Resolution JPEG 15360x8640 a 1920x1080 Do oe O O 15360x8640 English WE Music Playing Music 1 Press the lt A V button to select the
49. ng If the TV seems to have a problem refer to this description If none of these troubleshooting tips apply contact the Samsung customer service center English E Software Upgrade Software Upgrade can be performed by downloading the latest firmware from www samsung com to a USB memory device Current Version the software already installed in the TV English Installing the Latest Version e By USB Insert a USB drive containing the firmware upgrade file downloaded from TV Side Panel www samsung com into the TV Please be careful not to disconnect the power or remove the USB drive until upgrades are complete The TV will be turned off and on automatically after completing the firmware upgrade When software is upgraded The placement of the USB port may differ depending on the model video and audio settings you have made will return to their default settings We advise you to write down your settings so that you can easily reset them after the upgrade English e Online Geers Upgrade the software using the Internet First configure your network For detailed procedures on using the Network Setup refer to the Network Settings instructions If the Internet connection does not operate properly the connection may be broken Please retry downloading If the problem persists download by USB and upgrade e By Channel Upgrade the software using the broadcasting signal If the function is selected
50. nnection screen appears and network setting is done English LI Setting the Wireless Network E Wireless Network Setup Auto Most wireless networks have an optional security system that requires devices that access the network to transmit an encrypted security code called an Access or Security Key The Security Key is based on a Pass Phrase typically a word or a series of letters and numbers of a specified length you were asked to enter when you set up wireless security for your wireless network If you use this method of setting up the network connection and have a Security Key for your wireless network you will have to enter the Pass Phrase during the setup process When connecting Samsung Wireless LAN Adapter the screen pop up appears directly to set wireless network English How to set up automatically Go to Network Settings screen Select Start E Det aro GR The Network function searches for available wireless networks When done it displays a list of the 9 you want to connect to your wired network plug in a available networks a SAMSU NG gt 4 Inthe list of networks press the A or W button to select a network and then press ENTERLC button If the wireless router is set to Hidden Invisible you have to select Add Network and enter the correct network name and Security key to establish the connection English 5 If the Security screen pop up appears go to step 6 If you select the wirele
51. ns depends on the program being broadcasted Default CC1 CC4 Text1 Text4 analog channels only The Analog Caption function operates in either analog TV channel mode or when a signal is supplied from an external device to the TV Depending on the broadcasting signal the Analog Caption function may or may not work with digital channels English WE Auto Protection Time e Auto Protection Time Off 2 hours 4 hours 8 hours 10 hours If the screen remains idle with a still image for a certain period of time defined by the user the screen saver is activated to prevent the formation of ghost images on the screen English E Screen Burn Protection MENU System Screen Burn Protection ENTER To reduce the possibility of screen burn this unit is equipped with screen burn prevention technology The Time setting allows you to program the time between movement of the picture in minutes e Pixel Shift Off On Using this function you can minutely move pixels on the PDP in horizontal or vertical direction to minimize after image on the screen Optimum condition for pixel shift Item TV HDMI Natal bind nia English The Pixel Shift value may differ depending on the monitor size inches and mode This function is not available in the Screen Fit mode e Auto Protection Time Off 10 min 20 min 40 min 1 hour If the screen remains idle with a still image for a certain period of time defined by th
52. ny Philips Digital InterFace is used to provide digital sound reducing interference going to speakers and various digital devices such as a DVD player Audio Format You can select the Digital Audio output SPDIF format The available Digital Audio output SPDIF format may differ depending on the input source By connecting to 5 1ch speakers in a dolby digital setup maximize your interactive 3D sound experience Audio Delay Correct audio video mismatch when watching TV or video and listening to digital audio output using an external device such as an AV receiver Oms 250ms English Dolby Digital Comp Line RF This function minimizes signal disparity between a dolby digital signal and a voice signal i e MPEG Audio HE AAC ATV Sound Select Line to obtain dynamic sound and RF to reduce the difference between loud and soft sounds at night time Line Set the output level for signals greater or less than 31dB reference to either 20qB or 31dB RF Set the output level for signals greater or less than 20dB reference to either 10dB or 20dB English E Speaker Settings e Speaker Select External Speaker TV Speaker A sound echo may occur due to a difference in decoding speed between the main speaker and the audio receiver In this case set the TV to External Speaker When Speaker Select is set to External Speaker the volume and MUTE buttons will not operate and the sound settings will be limited
53. ol batteries with correct polarity Clean the transmission window located on the top of the remote control Try pointing the remote control directly at the TV from 5 6 feet away Program the Cable Set top box remote control to the operate the TV Refer to the Cable Set top box user manual for SAMSUNG TV code Check the supported resolution of the TV and adjust the external device s output resolution accordingly Refer to resolution settings in this manual Caption can not be selected in the TV menu when connected via HDMI or Component Caption must be activated on the external device English Issues Solutions and Explanations There is a plastic smell e This smell is normal and will dissipate over time from the TV TV Signal Information e This function is only available with digital channels from an Antenna is unavailable in the Self RF Coax connection Diagnosis Test menu TV is tilted to the right or Remove the stand base from the TV and reassemble it left side The Channel menu is grey The Channel menu is only available when the TV source is selected out unavailable English Issues Your settings are lost after 30 minutes or every time the TV is turned off You have intermittent loss of audio or video Solutions and Explanations If TV is in the Store Demo mode it will reset audio and picture settings every 30 minutes Please change from Store Demo mode to Home Use mode in the
54. ork settings o m Start Cancel If you want to connect to your wireless network plug in a Samsung Wireless LAN Adapter If it fails to set automatically check the connection of LAN port Z If you cannot find network connection values or if you want to set connection manually set it to Manual Refer to following How to set up manually E Wired Network Setup Manual Use the Manual Network Setup when connecting your TV to a network that requires a Static IP address Getting the Network Connection Values To get the Network connection values on most Windows computers follow these steps 1 Right click the Network icon on the bottom right of the screen 2 Inthe pop up menu that appears click Status 3 On the dialog that appears click the Support tab 4 On the Support Tab click the Details button The Network connection values are displayed English How to set up manually To set up your TV s cable network connection manually follow these steps 1 Follow Steps 1 through 2 in the How to set up automatically procedure 2 Select the IP Settings on network connection screen Set IP Mode to Manual Press the W button to go to the first entry DNS Server field Return 5 Enter the IP Address Subnet Mask Gateway and DNS Server values Use the number buttons to enter numbers and the arrow buttons to move from one entry field to another When done select the OK The network co
55. orks use a Dynamic IP address Some networks require a Static IP address If your network requires a Static IP address you must enter the IP address subnet mask gateway and DNS values manually on your TV s Cable Setup Screen when you set up the network connection To get the IP address subnet mask gateway and DNS values contact your Internet Service Provider ISP If you have a Windows computer you can also get these values through your computer Z You can use ADSL modems that support DHCP if your network requires a Static IP address ADSL modems that support DHCP also let you use Static IP addresses It is not Supported when the network speed is below or equal to 10Mbps Use Cat 5 STP Type cable for the connection Shielded Twist Pair y S English E Wireless Network Connection To connect your TV to your network wireless you need a wireless router or modem and a Samsung Wireless LAN Adapter WISOSABGNX WIS12ABGNX which you connect to your TV s back or side panel USB port See the illustration below Wireless IP sharer Wireless router having DHCP Samsung Wireless LAN Server Adapter The LAN Port on the Wall TV Side Panel The position of port may differ depending on the model English Samsung s Wireless LAN adapter is sold separately and is offered by select retailers and Ecommerce sites Samsung s Wireless LAN adapter supports the IEEE 802 11a b g and n communication protocols Sa
56. ower cord is securely plugged into the wall outlet and the TV Make sure the wall outlet is working Try pressing the POWER button on the TV to make sure the problem is not the remote control If the TV turns on refer to Remote control does not work below Ensure the Sleep Timer is set to Off in the System menu If your PC is connected to the TV check your PC power settings Make sure the AC power cord is plugged in securely to the wall outlet and the TV When watching TV from an antenna or cable connection the TV will turn off after 10 15 minutes if there is no signal English Issues There is no picture video Solutions and Explanations Check cable connections remove and reconnect all cables connected to the TV and external devices Set your external device s Cable Set top box DVD Blu ray etc video outputs to match the connections to the TV input For example if an external device s output is HDMI it should be connected to an HDMI input on the TV Make sure your connected devices are powered on Be sure to select the TV s correct source by pressing the SOURCE button on the remote control Reboot the connected device by reconnecting the device s power cable English Issues Solutions and Explanations Antenna Air Cable Connection The TV is not receiving all Make sure the coaxial cable is connected securely channels Please try Auto Tuning to add available channels to the chan
57. s music over voices Movie Provides the best sound for movies Clear Voice Emphasizes voices over other sounds Amplify Increase the intensity of high frequency sounds to allow a better listening experience for the hearing impaired lf Speaker Select is set to External Speaker Sound Mode is disabled English L Sound Settings MENU l Sound Sound Effect ENTERC E Sound Effect standard sound mode only Use the up and down arrow keys to select an option and then press ENTERL SRS TruSurround HD Off On This function provides a virtual 5 1 channel surround sound experience through a pair of speakers or headphones using HRTF Head Related Transfer J Function technology e SRS TruDialog Off On This function allows you to increase the intensity of a voice over background music or sound effects so that dialog can be heard more clearly English Equalizer Use Equalizer to customize sound setting for each speaker Balance L R Adjusts the balance between the right and left speaker 100Hz 300HZz 1kHz 3kHz 10kHz Bandwidth Adjustment Adjusts the level of specific bandwidth frequencies Reset Resets the equalizer to its default settings If Speaker Select is set to External Speaker Sound Effect is disabled English L Adjusting Sound Settings E Broadcast Audio Options MENU l Sound Broadcast Audio Options ENTERL Multi Track Sound MTS analog channels only Mono
58. ss router which does not have wireless security go to step 7 6 To set wireless security for the router enter the Security kKey Security or PIN When you enter the Security key Security or PIN use A W lt gt buttons to select number characters Press ENTER L to enter the characters You should be able to find the Pass Phrase on one of the set up screens you used to set up your router or modem 4 7 The network connection screen appears and network setting is done If it fails to set Security key Security or PIN select Retry or IP Settings If you want to set connection manually select the IP Settings Refer to following How to set up manually English E Wireless Network Setup Manual Use the Manual Network Setup when connecting your TV to a network that requires a Static IP address Getting the Network Connection Values To get the Network connection values on most Windows computers follow these steps 1 Right click the Network icon on the bottom right of the screen 2 Inthe pop up menu that appears click Status 3 On the dialog that appears click the Support tab 4 On the Support Tab click the Details button The Network connection values are displayed English How to set up manually To set up your TV s cable network connection manually follow these steps 1 7 2 e D Follow Steps 1 through 7 in the How to set up automatically procedure Select the IP Settings on network connect
59. ssing Solutions and Explanations Compression of video contents may cause picture distortion especially in fast moving pictures such as sports and action movies Low signal level can cause picture distortion This is not a TV problem Mobile phones used close to the TV up to 3 3 ft may cause noise in picture on analog and digital TV If you re using component connection make sure the component cables are connected to the correct jacks Incorrect or loose connections may cause color problems or a blank screen English Issues There is poor color or brightness There is a dotted line on the edge of the screen The picture is black and white Solutions and Explanations Adjust the Picture options in the TV menu go to Picture Mode Color Brightness Sharpness Adjust Energy Saving option in the TV menu go to MENU System Eco Solution Energy Saving Try resetting the picture to view the default picture setting go to MENU Picture Reset Picture If the picture size is set to Screen Fit change it to 16 9 Change cable Set top box resolution If you are using an AV composite input connect the video cable yellow to the Green jack of component input 1 on the TV English Issues When changing channels the picture freezes or is distorted or delayed Sound Problem There is no sound or the sound is too low at maximum volume Solutions and Explanations If connected to a cab
60. t Cancel schedule English E Schedule Manager You can set a desired channel to be displayed automatically at the intended time In addition you can view modify or delete a channel you have reserved to watch Set the current time first to use this function Using Option Menu Set each channel using the menu options Cancel schedule Edit Schedule Manually Schedule View Guide 1 Press the TOOLS button to select the Manually Schedule 4 You can press the EY Manually Schedule directly on the Schedule Manager screen 2 Press the lt P A V button to set the Antenna Channel Repeat Date Start Time e Antenna Select the desired broadcasting signal Channel Select the desired channel English Repeat Select Once Manual Sat Sun Mon Fri or Everyday to set at your convenience If you select Manual you can set the day you want The v mark indicates the day is selected e Date You can set desired date It is available when you select Once in Repeat e Start Time You can set start time you want If you want to edit or cancel the schedule select the reserved schedule on the Booking List Press the TOOLS button and select the Edit Schedule or Cancel schedule If you select the View Guide you can see the Guide screen English 2 Memorizing channels MENU Ml Channel ENTERL4 E Antenna Air Cable Before your television can begin memorizing the available channels you must specify the type of signal sour
61. t the channel automatically changes to the selected program channel at the specified time Program entries may appear blank or out of date depending on a channel status Po 6 Mon 25 Jan 6 38 am DTV Air 3 RCN MPEG4 HD Home and Away 6 00 am 6 30 am ATLETICO MG X CORINTHIANS HD Channel View All Today 6 00 am l 6 30 am 7 00 am 1 Caracol MPEG 2 JORNAL DA GLOBAL l Tine Team 2 RCN MPEG2 No Information l 3 RCN MPEG4 No Information Fiv Dark Angel 4 PRUEBA HD No Information 5 QVC No Information v 6 R4DTT No Information A Schedule Mgr 8 24 Hours 24 Hours CH Mode ji Information Page Schedule It may differ depending on the model English Seo 8S EX Red Schedule Mgr Moves to the Booking List in Schedule Manager E Green 24 Hours Viewing the list of programs to be broadcasted before 24 hours Yellow 24 Hours Viewing the list of programs to be broadcasted after 24 hours BP Blue CH Mode Select the type of channels you want to display on the Channel List window All TV Favorites 1 5 1 Information Displays details of the selected program and let you make a manual booking gt Page Move to previous or next page 4 Watch Schedule When selecting the current program you can watch the selected program When selecting the future program you can reserve to watch the selected program To cancel the schedule press the ENTER C button again and selec
62. ternet Service Provider for more information English Issues Unable to connect to the network Connected to your local network but cannot connect to the Internet Network setup complete but cannot connect to the Internet Solutions and Explanations Check if your IP address is set correctly in IP Settings Contact your Internet Service Provider for more information Check your Internet LAN cable is connected correctly to LAN port of router Check the DNS settings in IP Settings If the problem persists contact your Internet Service Provider to access the Internet Log in Internet service network If the problem persists contact your Internet Service Provider to access the Internet English The check list for wireless network connection failure When wireless network connection failed try to apply the following information to each issue Issues Solutions and Explanations Wireless network e No wireless router selected Go to Network Settings to select your connection failed router Unable to connect to Check that the router is turned on and if it is on try turning it off and on wireless router again Check if you need to enter a security key to use the router IP auto setting failed Try the following to set your IP address automatically or set your IP address manually by selecting IP Settings Ensure DHCP server is enabled on router and unplug and re plug in the router Check if you ne
63. the Channel List e Tools Displays the option menu lt gt CH Mode Channel Move to the All TV Analog or Favorites 1 5 When you select the Program View in g_ Tools menu you can move to other channels using 4 gt Channel button e C Watch Information Watches the channel you select Displays details of the selected program e Page Move to next or previous page English How to use Schedule Viewing in Channel List digital channels only When you set the Schedule Viewing in Channel List you can only set the program in Program View 1 Press the CH LIST button then select a desired digital channel 2 Press TOOLS button and then select the Program View The program list for that channel appears 3 Press the A V buttons to select the desired program then press the ENTERC4 Information button Select Schedule Viewing then press the ENTERL button when done gt If you want to cancel Schedule Viewing follow steps 1 through 3 Select Cancel schedule y S English Using Option Menu Set each channel using the Channel List menu options Program View Edit Favorites Lock Unlock Channel Name Edit Edit Channel Number Delete Information Sort Change Antenna Edit Mode Option menu items may differ depending on the channel status 1 Select a channel and press the TOOLS button 2 Select a function and change its settings Program View digital channels only Displays the progr
64. the PIP function Air Cable Air Cable Select either Air or Cable as the input source for the sub screen Channel Select the channel for the sub screen Size Liml _ l Select a size for the sub picture Position Lal C5 F_ k_l Select a position for the sub picture Sound Select Main Sub You can choose the desired sound Main or Sub in PIP mode English lt Economical Solutions Eco Solution e Energy Saving Off Low Medium High Picture Off 08 This adjust the brightness of the TV in order to reduce power consumption If you select Picture Off the screen is turned off but the sound remains on Press any button except volume button to turn on the screen Eco Sensor Off On To enhance your power savings the picture settings will automatically adapt to the light in the room Not available for LED 4 series If you adjust the Backlight Cell Light the Eco Sensor will be set to Off English Min Backlight Min Cell Light When Eco Sensor is On the minimum screen brightness can be adjusted manually If Eco Sensor is On the display brightness may change become slightly darker in most cases depending on the surrounding light intensity No Signal Power Off Off 15 min 30 min 60 min Sets how quickly the TV switches to standby mode if no picture is being received Disabled when the PC is in power saving mode e Auto Power Off Off On The TV will be automatical
65. torage Class MSC devices MSC is a Mass Storage Class Bulk Only Transport device Examples of MSC are Thumb drives Flash Card Readers USB HUB are not supported Devices should be connected directly to the TV s USB port Before connecting your device to the TV please back up your files to prevent them from damage or loss of data SAMSUNG is not responsible for any data file damage or data loss The HDD Hard Disk Drive connected to USB is not supported Do not disconnect the USB device while it is loading English The higher the resolution of the image the longer it takes to display on the screen The maximum supported JPEG resolution is 153860 x 8640 pixels For unsupported or corrupted files the Not Supported File Format message is displayed MP3 files with DRM that have been downloaded from a non free site cannot be played Digital Rights Management DRM is a technology that supports the creation distribution and management of the content in an integrated and comprehensive way including the protection of the rights and interests of the content providers the prevention of the illegal copying of contents as well as managing billings and settlements A USB device that requires high power more than 500mA 5V may not be supported If the TV has been no input during time set in Auto Protection Time the Screensaver will run English The power saving mode of some external hard disk drives may be released automat
66. your PC English When you use AllShare Play mode through a network connection according to functions of the provided server The sorting method may vary The lt lt REW gt gt FF or Lit Pause buttons may not work depending on the content information If you experience any file stuttering issue while playing a video over a wireless network we recommend using a wired network English L Screen Display Move to the desired file using the lt A buttons and then press the ENTERL4 or Play button The file is played The screen may differ depending on the way to enter the screen The displayed image may differ depending on the model Information You can ascertain the 4 Information selected device name f webs You can ascertain the contents mode folder file ges name size and created d name page date of the selected file India s Life Tonight Show Whale s Life Ca Page Move a ols 9 a File List Section Operation Buttons You can confirm the L Play Play the selected file files and groups that are a Tools Displays the option menu sorted by category D Return Move to the previous step lt lt gt gt E amp Page Move Move to up or down page English M Videos Playing Video 1 Press the lt A V button to select the desired video in the file list 2 Press the ENTERL button or gt Play button The selected file name is displayed on the top with
67. your TV to the Internet If your Internet service provider requires an ID or password to connect to the Internet your TV may not be able to connect to the Internet If this is the case you must enter your ID or password when connecting to the Internet The internet connection may fail because of a firewall problem If this is the case contact your Internet service provider If you cannot connect to the Internet even after you have followed the procedures of your Internet service provider please contact Samsung Electronics English gt LJ Managing the Network Connected Devices E Wi Fi Direct MENU Network Wi Fi Direct gt ENTER Q Set to connect the TV to wireless mobile devices Using this function you can connect wireless mobile devices with your TV directly without a router You can use this function when connecting the Samsung Wireless LAN Adapter lt It only supports AllShare Play function It may not be supported depending on the mobile device English How to connect the Wi Fi device to your TV using Wi Fi Direct function 1 Goto Wi Fi Direct screen The TV starts to search devices 2 Turn on the Wi Fi Direct function on your device Select the desired device and then press ENTERLC button PBC Press the WPS PBC button on your device within 2 minutes Your TV automatically acquires all the network setting values it needs and connects to your network PIN Input the displayed PIN on your d

Samsung UN26EH4000M User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents