Samsung AW12PHA User Manual
Contents
1. The automatic protection feature may be triggered and the air Higher temperatur e 9r Temperatures conditioner stopped A water leakage or some other malfunction may happen if the Lower temperatures heat exchanger freezes Water way condense on and drip from the surface of the unit if Higher humidity levels it is used for long periods Cleaning Your Air Conditioner Be sure to clean the air filter periodically to maintain the air conditioner in the best condition for a long period of time PORTANT When cleaning the air conditioner turn it off and pull out the power plug 1 Holdthe front grille handle slightly pull it to the left side and open the front grille gt The removal of the front grille makes it easier to clean the air conditioner Open the grille as much as possible CAUTION Removal and Reassembly of the Front Grille For user s safety a safety clip has been installed in the front grille 1 Grasp the lower part of the front grille and the front grille handle then open the grille The open angle of front grille has not to be exceeded 25 degree Lift the front grille slightly and remove it from the front panel Reassembling of front grille should be done in reverse order of disassembly Front grille Grille groove 2 Pull the air filter to the right side 3 Remove all dust on the air filter with a vacuum cleaner or brush Body gui2. umm USER S MANUAL AW08PH Series AW08PK Series AW12PH Series AW12PK Series AW18PH Series AW18PK Series AW24PH Series AW24PK Series AW122PB Window type Room Air Conditioner Cooling m NU wn NE N I DB98 26004A 4 Register your product at www samsung com global register Safety Precautions The following safety precautions must be taken when using your air conditioner WARNING DURING OPERATION DISPOSING OF THE UNIT OTHERS Risk of electric shock Can cause injury or death e Disconnect all remote electric power supplies before servicing installing or cleaning This must be done by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard Users of this product are cautioned not to attempt repair of this product at their own discretion Instead they are requested to directly contact a designated service center or the outlet at which the product was purchased Never spill any kind of liquid into the unit Should this happen unplug or main Switch off the unit and contact an authorized service center Do not insert anything between the air outlet blades because the inner fan may be damaged and could cause injury Keep children away from the unit Do not place any obstacles in front of the unit Do not spray liquid of any kind into the indoor unit Should this happen switch off the breaker used for your air conditioner and contact your installation speci
3. 362 603 www samsung com au HONG KONG 2862 6001 www samsung com hk INDIA 3030 8282 1800 110011 www samsung com in INDONESIA 0800 112 8888 www samsung com id MALAYSIA 1800 88 9999 www samsung com my PHILIPPINES 1800 10 SAMSUNG 7267864 www samsung com ph SINGAPORE 1800 SAMSUNG 7267864 www samsung com sg THAILAND 1800 29 3232 02 689 3232 www samsung com th VIETNAM 1 800 588 889 www samsung com vn SOUTH AFRICA 0860 7267864 SAMSUNG www samsung com za
4. MIEL A aaa na Ega anapa ANN 13 m Selecting Good Morning mode saeaaenae ena ane anane anana anana nenen nana ene 14 m Selecting Energy saving mode eesaenenenae anaa nana a nana naen aana e nana ee aee 15 RECOMMENDATIONS FOR USE m Temperature and Humidity Ranges ssneneeneanan nen annneenn nane nn sanan 15 m Cleaning Your Air Conditioner aessesen ena aee anane a nane n aana a nenen anna ene 16 m Solving Common Problems nennen 17 m Technical Specifications esesesssseeeeneeeeeneneneen nennen 18 INSTALLATION t 19 CAUTION The high inrush current of the starting compressor motor can have adverse effects to the operation of other equipment under unfavorable mains conditions This equipment does not comply with the relevant technical standards for the limitation of voltage fluctuations and flicker Before connection this equipment to the power supply system please report to your suply authority and obtain the consent Do not connect other electric appliances to the same supply lines AW18 The maximum permissible system impedance at the power junction box is 0 24 ohms Usually the maximum permissible mains impedance will not be exceeded when the branch to the power outlet is fed from a junction box with a rated current of 32A Air Conditioning Unit Main Parts Buttons and Display The design and shape are subject to change according to the m
5. should have sufficient strength and durability for operation of the air conditioner and for prevention of any vibration or noise If itis weak reinforcement work should be performed separately It is advisable to install the air conditioner in the north or west side to prevent the effect of direct sunlight When installing it in the south or east side due to unavoidable circumstances it is advisable to install the sunshade to prevent the direct sunlight In this case take care not to cause any hindrance to the flow of outside air When installing the air conditioner be sure to obtain sufficient space on the rear side of the unit for smooth flow of air When operating the air conditioner in closed areas such as inner building with cooling operation and result in trouble with the unit See the illustration below The appliance must be fixed well by screw or similar Awning method TIL Fence wall or other aim MODEL AW08 AW12 AW18 AW24 obstacle Approx 3 150mm min If the wall is greater than 150mm thick cut the wall back on a 45 angle if possible Outdoor side 45 C ES BES a Indoor side 100mm or more Installation cont In some region drain tube and drai
6. when you are cooling your room to switch the air conditioner off automatically after 8 hours Remote Contro Control Panel gt The Good Morning function can be set whether the air conditioner is m switched on or off and this function can be selected for any mode Press the button on the remote control or o Press the button on the unit Result 9 Each time you press a butoon the unit beeps The 35 indicator and 4 will be displayed The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time f Good Morning is selected after switching on the unit the air conditioner will run in Cool mode During this period the temperature displayed is one you set for the Cool mode If the Good Morning is selected before switch on the unit the air conditioner starts running in Cool mode and the aga EEA temperature is set to 26 C H v The fan is running in low mode and you can adjust the di i speed To Cancel the Good Morning Timer If you no longer wish to use the Good Morning mode that you have set you can cancel it at any time 1 Press the button on the remote control or press the button on the unit to switch off the air conditioner 2 To cancel a selected Good Morning mode you can also press the E599 Gime or button on the remote control or press the i or button on the unit Result The unit beeps The indicator is no longer dis
7. 00BTU h 2820W 12 5A AW12PKAB 115V 60Hz 12000BTU h 1110W 10 0A AW12PKBB 220V 60Hz 12000BTU h 1110W 5 2A Installation for 60Hz 1 Electrical Requirements For personal safety This appliance must be properly grounded Do not under any circumstances cut or remove the third grounding prong from the power cord We recommend that you do not use an extension cord or an adapter plug with this appliance Do not change the plug on the power cord of this appliance Follow national electrical codes or local codes and ordinances 115V 230V 208V 230V 208V 230V 208V 15 AMP Circuit 20 AMP circuit 15AMP circuit 30 AMP circuit parallel type perpendicular type tandem type tandem type 0 Q ve If the electric supply provided does not meet the above specifications call a licensed electrician Aluminum house wiring may pose special problemsconsult a qualified electrician This unit requires a separate circult serving only this appliance Installation cont Before installation be sure to check the installation area or the air conditioner and drain hose Checkpoints prior to installation 1 Check the cabinet and front grille of the unit for any harmful defects such as scratches Be sure to check the power supply Refer to the specifications on the label attached to the unit Installation Conditions 1 As the unit is heavy the wall or window of the installation area
8. alist Make sure that the unit is correctly ventilated at all times Do not place clothing or other materials over it If the wireless remote control will not be used for a long time remove the batteries If applicable When using a wireless remote control the distance should not be more than 7 meters from the air conditioner If applicable The air conditioner must be plugged into its own specific power source which must be installed in compliance with national wiring earthing and safety regulations If the power cord is damaged in any way it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard This device must be installed according to the national electrical rules The appliance must be installation that the plug should be easily accessible after installation If the fuse on PC board is broken please change it with the type of T 3 15A 250V The breaker of the air conditioner should be all pole switch and the distance between its two contacts should be no less than 3 5mm Such means for disconnection must be incorporation in the fixed wiring Before throwing out the device it is necessary to pull back the battery cells and get rid of them safely for recycling reasons When you need to dispose of the unit consult your dealer If pipes are removed incorrectly refrigerant may blow out and come into contact with your skin causing injury Releasing refrigerant
9. as been installed by your installation specialist Your Owenr s Instructions contain valuable information on using your air conditioner Please take the time to read them as they will help you take full advantage of the unit s functions This Owner s Instructions is just for using your air conditioner correctly Thus the illustrations shown in this manual may not exactly match your air conditioners The booklet is organized as follows The following figures are shown on pages 4 and 5 Air conditioning unit main parts buttons and display Remote control buttons They will help you find the buttons and understand the symbols displayed In the manual you will find a series of step by step procedures for each function available The illustrations in the step by step procedures use four different symbols A m s PRESS PUSH IMPORTANT Moreover applicable wherever the illustrations show the positions of the buttons on both the remote control and the unit itself For the The illustrations have a Remote control Gray background Example Unit itself White background Example Power Inserting the Remote Control Batteries You must insert or replace the remote control batteries when You purchase the air conditioner The remote control does not work correctly Use two AAA LR03 1 5V batteries Do not use old batteries or different kinds of batteries together a Batteries may be completely discharged afte
10. de 4 When you have finished insert the air filter back into its original position 5 Wipe the surface of the unit with a neutral detergent and then wipe it again with dry cloth Be sure not to use benzene solvent or other chemical products gt If you Then The air conditioner has two or three grille 7 grooves depending on the model Will not be using the Set the fan going for a few hours to air conditioner for a dry the inside of the air conditioner long period of time thoroughly Switch the air conditioner off and unplug it from the wall socket Clean the filter and outer surfaces Have not used the air Set the fan going for a few hours to conditioner for a long dry the inside of the air conditioner period of time thoroughly Solving Common Problems Before contacting the after sales service perform the following simple checks They may save you the time and expense of an unnecessary service call Problem Explanation Solution The air conditioner does not operate at all Check that the circuit breaker used for the air conditioner has not been triggered Check that the power cable is plugged into a wall socket and the socket is switched on if necessary Check that the operating mode indicator COOL or FAN on the unit is lit up if necessary press On Off button on the remote control or unit The air conditioner does not operate wit
11. e 5 On Off button Power Result The air conditioner starts up in the Cool mode The unit beeps twice 3 If the FAN indicator is not lit up on the unit Press the button on the remote control Cx E Press the button on the unit one or more times until the FAN indicator lights up Result The unit beeps each time you press the button Dr The air conditioner starts up in Fan mode gt You can change modes at any time When the air conditioner is in the Fan mode the temperature is not dis played in this case you do not need to set the temperature d 11 or Press the button on the unit one or more times until the desired fen speed F1 F2 or F3 is displayed Low F 1 Low Speed c Med Speed 4 To set the fan speed to Then Press the ved or button on the remote control as desired 5 Tocontrol the direction of the air flow refer to page 11 Remote Control Removing Excess Humidity Control Panel Power If the atmosphere in your room is very humid or damp you can remove excess humidity without lowering the room temperature too much If necessary press the O On Off button Result The air conditioner starts up in the Cool mode The unit beeps The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up to coo
12. erating time reaches zero gt You can change the fan speed and others after setting the On Timer To Cancel the On Timer To cancel the On Timer press e on the remote control or on the unit one or more times until gg is displayed e 5 On Off button on the remote control or unit Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given period of time You can set the period of time from 1 hour to 24 hours You can select the Off Timer only when the air conditioner is on Remote Control Control Panel 1 Check that the air conditioner has been switched on if necessary press the 1 On Off button Power 2 Setthe operating time by pressing on the remote control gl or 3 2 e on the unit one or more times E Possible time is between 1 hour and 24 hours inclusive Result The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time The air conditioner switches off automatically when the operating time reaches zero gt You can change the fan speed and air flow direction and others after setting the Off Timer To Cancel the Off Timer To cancel the Off Timer press o on the remote control or on the unit one or more times until mpa is displayed Ka D On Off button on the remote control or unit d Selecting Good Morning Mode The Good Morning mode can be used
13. h the remote control Check that there are no obstacles between you and the unit Replace the remote control batteries if necessary Check that you are close enough to the unit seven metres yards or less No beep is heard when you press 5 On Off on the remote control Check that you are pointing the remote control at the remote control sensor on the unit Replace the remote control batteries if necessary The air conditioner does not cool The air flow direction does not change when you press the or on the unit button Check that the correct operating mode has been selected COOL The room temperature may be too low Dust may be blocking the air filter refer to page 16 for cleaning instructions Check that there is no obstacle blocking the air flow into or out of the unit Check that the air conditioner has been switched on if necessary press 5 On Off button on the remote control or unit The timer is not correctly triggered Check that the timer has been programmed correctly see page 12 13 Odour is permeated in the room during air conditioning Air the room Technical Specifications Design and specifications are to change without notice Voltage 4 z Power Operating mode Freon Capacity Consumption Current AW12PKAA 115V 60Hz 12000BTU h 1230W 11 2A AW12PKBA 220V 60Hz 12000BTU h 1230W 5 5A AW18PKBA 220V 60Hz 18000BTU h 1850W 8 3A AW24PKBA 220V 60Hz 240
14. into the atmosphere also damages the environments Please recycle or dispose of the packaging material for this product in an environmentally responsible manner Never store or ship the air conditioner upside down or sideways to avoid damage to the compressor The appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance Max current is measured according to IEC standard for safety and current is measured according to ISO standard for energy efficiency Contents PREPARING YOUR AIR CONDITIONER Safety Precautions uu aaa bi Mee aee an ELLE ER LAN a M e alani 2 m Air Conditioning Unit Main Parts Buttons and Display 4 m Remote Control Buttons sssseeeeeneenneeneeneen enne 5 m Getting Started sssssssssssseseseeeeeenee nene nnne nennen rs 6 m Inserting the Remote Control Batteries ssseeeenene 7 OPERATING YOUR AIR CONDITIONER m Cooling Your ROOIfi iicet teer ANA ce np las 8 m Airing Your ROOM aaa AE enm eene nennen nnne nennen 9 m Removing Excess Humidity 10 m Adjusting the Air Flow Direction Horizontally eeeeeeeeeee 11 m Adjusting the Air Flow Direction Vertically eseennee 11 PROGRAMMING YOUR AIR CONDITIONER m Setting the On Timer rennen nennen nnns 12 a Setting the Off TIMOR sasasi aana eg Aa A NGAEN
15. l normally after three minutes If the EJ is not displayed at the top of the control panel press the button on the control panel or press button on the remote control one or more times until it appears Result The unit beeps each time you press the button The air conditioner runs in Dry mode gt You can change modes at any time To adjust the temperature press the 4_ or C J buttons one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press the C or C v buttons The temperature is adjusted by 1 C The unit beeps The air conditioner starts removing the excess humidity the quality of air is adjusted automatically To control the direction of the air flow refer to page 11 Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room you can adjust the orientation of the inner air flow blades on the right hand side of the unit thus increasing the efficiency of the air conditioner Remote Control Control Panel 1 Press the or on the unit button on the remote control Result The inner blades swing automatically left and right ol l Swing air swing m 2 To stop the blades moving left and right press the or on the unit button in the remote control gt To stop the blades in a specific position and orient the air flow in the cor
16. n pan may not be supplied Plesae contact the sales agent Installation of the Drain Tube Fix the drain tube as shown in the figure Drain Tube Screws 2EA Contact SAMSUNG WORLD WIDE If you have any comments or questions regarding a Samsung products contact the SAMSUNG customer care center Country Customer Care Center B ELECTRONICS Web Site MEXICO 01 800 SAMSUNG 7267864 www samsung com mx ARGENTINE 0800 333 3733 www samsung com ar BRAZIL 4004 0000 www samsung com br CHILE 800 726 7864 SAMSUNG www samsung com cl COLOMBIA 01 8000 112 112 www samsung com co COSTA RICA 0 800 507 7267 www samsung com latin ECUADOR 1 800 10 7267 www samsung com latin EL SALVADOR 800 6225 www samsung com latin GUATEMALA 1 800 299 0013 www samsung com latin JAMAICA 1 800 234 7267 www samsung com latin PANAMA 800 7267 www samsung com latin PUERTO RICO 1 800 682 3180 www samsung com latin REP DOMINICA 1 800 751 2676 www samsung com latin TRINIDAD amp TOBAGO 1 800 7267 864 www samsung com latin VENEZUELA 1 800 100 5303 www samsung com latin RUSSIA 8 800 200 0400 www samsung ru KAZAHSTAN 8 800 080 1188 www samsung kz UZBEKISTAN 140 1234 www samsung uz UKRAINE 8 800 502 0000 www samsung com ur LATVIA 800 7267 AUSTRALIA 1300
17. odel Air Outlet Inner air flow blades EB right left orientation Air inlet Inside A B up down orientation The air filter is Z A Air inlet Outside Outer air flow blades located in side Wy Ventilation lever Y The power plug may be not supplied depending on the model zm The type of the power plug ES Power plug jj may differ according to the V type of local power supply Operating mode indicators COOL DRY FAN Good do Morning setting button CHE Morning Temperature Timer setting A Temperature adjustment T emp buttons Timer setting button Energy Saver indicator Timer indicator Good Morning indicator Operating mode selection button COOL DRY FAN Energy Saver button Remote Control sensor Air flow blade Air Swing Mode swing button Fan speed adjustment 41 Fan Speed E Savern LOU button On Off button Remote Control Buttons Timer setting button N J Temperature adjustment Selecting Good Morning c 7 1 button button di Fan speed adjustment Operating mode button selection button Power Swing L D 3 1 on off button oS Energy Saver button it Saver Air flow blade swing button Getting Started You have just purchased a window type room air conditioner and it h
18. plyed The air conditioner operates in the mode selected last gt If you select the Energy Saving mode in the Good Morning mode the Good Morning mode will be canceled and the air conditioner will start up in the Energy Saving mode Selecting Energy Saving Mode If you wish to save Energy when using your air conditioner select the Energy Saving mode with the Energy Saver button Remote Control Control Panel 1 Toselect the Energy Saving mode press the Energy Saver button on the remote m control or unit one or more times until the Energy Saver indicator lights up ri E Da Result The fan and compressor cycle on and off together The fan will continue to run for a short time after the E saver compressor cycles off N e o 2 To stop the Energy Saving mode press the Energy Saver button on the remote control or unit again Result 8 The fan runs at all times while the compressor cycles on and off gt If you select the Good Morning mode in the Energy Saving mode the Energy Saving will be cancelled and the air conditioner will start up in the Good Morning mode Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used in the best condition Mode IndoorTemperature OutdoorTemperature Indoor Humidity Cooling 21 C to 32 C approx 21 C to 43 C approx 80 or less If the air conditioner is used at Then
19. r 12 months even if they have not actually been used 1 Push the battery cover on the rear of the remote control with your thumb in the direction of the arrow and remove it 2 Insert the two batteries taking care to respect the polarities 9 on the battery with on the remote control 9 onthe battery with on the remote control 3 Close the cover by sliding it back unitl it clicks into place Result You can control all the functions your air conditioning unit directly from your seat using the remote control Cooling Your Room You must select the Cool mode if you wish to lower the temperature in your room You can also set the fan speed Remote Control Control Panel 1 Power a If necessary press the b On Off button Result The air conditioner starts up in the Cool mode The unit beeps twice The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being Plugged in Stopped It will start up to cool aotomatically after about three minutes If the COOL indicator is not lit up on the unit Press the button on the remote control or Press the button on the unit one or more times until the COOL indicator lights up Result The unit beeps each time you press the button The air conditioner starts up in Cool mode gt You can change modes at any time To adjust the temperature press the CAN or GVA but
20. responding direction simply press the or on the unit button on the remote control when the blades are in the desired position Adjusting the Air Flow Direction Vertically Again depending on the position of the unit in your room you can adjust the orientation of the outer air flow blades on the right hand side of the unit RECOMMENDATION When Adjustthe blades to face M NG LSM Cooling Upwards many Adjust the air flow blades to the desired position by pushing them upwards or downwards gt f you orient the air flow blades downwards and the unit operates in Cool mode for a long period of time dew may From on the surface of the blades Drip from the blades Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period time You can set the period of time from 1 hour to 24 hours Remote Control Control Panel You can select the On Timer only when the air conditioner is off Power m Check that the air conditioner has been switched off if necessary press the b On Off button 2 Setthe operating time by pressing z on the remote control or EE on the unit one or more times Possible time is between 1 hour and 24 hours inclusive Result The remaining time is displayed and decreased by 1 hour automatically to indicate the remaining time The air conditioner switches on automatically when the op
21. ton on the remote control one or more times until the required temperature is displayed To adjust the temperature press the J or v J button on the unit one or more times until the required temperature is displayed Possible temperatures are between 18 C and 30 C inclusive Result Each time you press the temperaure buttons The temperature is adjusted by 1 C and displayed on the control panel The unit beeps The air conditioner starts cooling if the room temperature is higher than the selected temperature To set the fan speed to Then Press the ved or button on the remote control as desired or Press the button on the unit one or more times until the desired fen speed F1 F2 or F3 is displayed F Low Speed F 2 Med Speed rc F 3 High speed lt Um Low Sa To control the direction of the air flow refer to page 11 Airing Your Room If the atmosphere in your room is stale you can air it using the Fan feature and if necessary evacuate the stale air outside 1 If you wish to evacuate stale air outside push the ventilation lever on the front of the unit to the right and the open position 1ST Result 8 The air inside the room circulates and stale air is evacuated outside Otherwise push the ventilation lever to the left and the closed position ST Result 8 The air simply circulates inside the room Remote Control Control Panel 2 fnecessary press th
Download Pdf Manuals
Related Search