STK-460 Vertical Protection PIR Motion Detector S A M T E K
Contents
1. STK 460 Vertical Protection PIR Motion Detector SAMTEK Installation Manual Introduction This high performance RFI shielded infrared unit is ideally suited to monitor exit requests in card access systems as well as handle other security vertical view protection requirements Specialized design features of the 460 include a low noise high sensitivity dual element sensor which permits quicker response at close range a unique full curtain adjustable pattern lens Auto Pulse Signal Processing automatic compensation for temperature variation in the protected area an adjustable signaling period and a choice of two different operating voltages 12 24V Installation Caution When selecting detector location please ensure that the 460 is not placed directly above or in close proximity to a heat source that could cause rapid fluctuations in detector temperature If you are using the 460 for card access systems a hand sized movement will be accurately detected from a distance of up to 2 1 meters For body sized movements the 460 will detect accurately up to 6 6m Opening the Detector Prior to Installation Place a small screwdriver in the two insertion points found at the base of the detector Gently pry off the back cover of the detector J1 LED JUMPER Mounting ga A a Knock out the wire hole entry you wish to use and run the wire through the entry tens a When installing you can vary the distance from the detector to the wa2. ll using the Gomes M Six Spacers supplied with the 460 Make sure that nothing blocks the view of the J4 OPERATING VOLTAGE lens opening i e a door frame or any other object The 460 can be mounted with rce screw JUMPER a view down up or to the side Connect the wires by using either the relay output 0 15A max or transistor 2A max output option depending on your detector O ELECTRICAL CONNECTORS model Q SIGNAL DURATION TRIMMER Caution When driving high current loads like door locks do not exceed the maximum current of 2 Amperes DC When using the relay output the maximum AtameeRswrch f WIREHOLE current should not exceed 0 15 Amperes The transistor output is connected to ground in the CLOSED position arc LaseL Q sac rcs spacers Opening the Detector After Installation Genily pull on the lip found at the base of the detector near the lens opening To close the detector replace the detector cover on its base and snap it on Beam Pattern Adjustments The 460 has two adjustable patterns 0 degrees and 10 degrees It is PCB TERMINAL CONNECTION factory set in the O degree lens position To change the beam angle POWERINPUT ANTI TAMPER OUTPUT remove the lens holder pull out the lens and rotate it 180 degrees ea A oo Replace the lens in the detector and gently put back the lens holder MAX JEP Oe ensuring that the small opening in the lens holder faces the inside left corner of the len
3. oltage 9 to 16 VDC or 20 to 27VDC nstallation Height 2m to 2 7m 7ft to 9ft Cylindrical LODIFF segment full curtain Fresnel card access applications 6 6m x 4 5m 21 x 15 to 9ft eee r 2 a i 28VDC 0 15A N C or N O Anti Tamper switch 28VDC 0 15A opens when cover removed
4. s O Alarm Duration Adjustments Rotate the trimmer clockwise to increase signal time and counter clockwise to decrease signal time JUMPER SETTING The 460 has four jumpers three on the bottom left and one on the bottom right ON OFF J1 Enables LED indicator in the ON position J2 Selects the output type in the ON position the output type is normally closed open when signal is detected In the OFF position the output type is normally opened output is closed when signal is detected J3 Turns the Auto pulse on and off Please note that when the jumper is ON Auto pulse is OFF In security applications the Auto pulse setting should always be ON Jumper OFF In card access applications the Auto pulse should be turned OFF Jumper ON to achieve more rapid detection J4 Selects the operating voltage Set in the ON position for 12 VDC and OFF for 24VDC operation The Seller warrants its products to be free from defects in PATTERN OF COVERAGE materials and workmanship under normal use for a period Side view px Tanne of one year Except as specifically stated herein all a express or implied warranties whatsoever statutory or otherwise including without limitation any implied warranty of merchantability and fitness for a particular 2 4m ee purpose are expressly excluded Since Seller does not install or connect the products and because the products ma
5. y be used in conjunction with products not manufactured by the Seller Seller cannot guarantee the performance of the security system Seller obligation and liability under this warranty is expressly limited to repairing or replacing at Seller s option any products not meeting the specifications In no event shall the Seller be liable to the buyer or any other person for any losses or damages whether direct or indirect or consequential or incidental including without limitation any damages for lost profits stolen goods or claims by any other party caused by defective goods or otherwise arising from the improper incorrect or otherwise faulty installation or use of the merchandise sold Note It is up to the local authorities that have jurisdiction over the area in which the device is being installed that can authorize if the device can be used in lieu of panic hardware or can be installed in a fail secure condition In accordance with UL294 this device can be installed for use in Access Control applications The user is cautioned that any changes or modifications not expressly approved by Posonic Security Systems could void the user s authority to operate use the equipment 6 6m _ m position position A 0 B 10 A Grn 0 9m 0 9m ECHNICAL SPECIFICATIONS Processing Threshold or Auto pulse Automatic temperature compensation metal shielding Detection Speed 0 2m to 7m sec 0 6ft to 23ft sec 10 C to 50 C 14 F to 122 F V
Download Pdf Manuals
Related Search