Home
USER MANUAL
Contents
1. LOGOSOL USER MANUAL USER MANUAL IN ORIGINAL FORMAT LOGOSOL Speed Saw 4 Read through the user manual carefully and make sure you understand its contents before you use the planer moulder This user manual contains important safety instructions operator or others A WARNING Incorrect use can result in serious personal injury or even death to the 4 N Thank you for choosing a LOGOSOL machine Welcome We are very pleased that you have demonstrated your confidence in us by purchasing this planer moulder We will do our utmost to meet vour expectations LOGOSOL has been manufacturing wood processing machines since 1988 and since then we have supplied approx 30 000 machines to satisfied customers worldwide We care about your safety as well as we want you to achieve the very best possible reslults from your machine We therefore recommend that you take the time to read this user manual from cover to cover before you begin sawing Remeber that the machine itself is just part of the value of the product Much of the value is also to be found in the expertise we pass on to you in the user manual It would be a pitty if that were not utilized We hope you get a lot of satisfaction from the use of your new machine Bug O Belin Bengt Olov Bystr m Founder and Chairman of the Board LOGOSOL AB H rn sand Sweden LOGOSOL is engaged in continuous development of its products We must therefore reserv
2. Take the line and thread it through the spring the plastic bushing and the tube as shown above Tie a knot at the line end and fit the plastic bushing and the spring in the spring attachment 12 Fit an M8 flat washer on an M8x30 hex bolt and fasten it with an M8 flange nut with the flange facing outwards towards the line Then thread the line through the line holder let it round the body of the bolt and finally thread the line out the same way Fit the thick flat washer and the outer nut Strech the line before tightening the nut 15 13 The line holder 12 is screwed to the electric saw with two M6 flange nuts 14 The electric cable from the feeder unit is threaded through the cable hook 19 which works a strain relief The hook is then hung up on the chain tensioner knob 16 LOGOSOL Speed Saw LIFTING INSTRUCTIONS amp SETUP Fit the guide bar and chain after the saw has been mounted on the LOGOSOL Sawmill The Speed Saw should be mounted on the guide rail of the sawmill before power is connected to the machine The saw unit weighs 40 47 kg 88 104 Ibs Best is if you have another person helping you lift the saw onto the ramp and hold it steady until it is correctly pushed onto the guide rail of the sawmill Carefully slide the saw
3. chainsaw unit that is intended for usage on the LOGOSOL Sawmill The slide elements which fit on the sawmill guide rail are integrated in the machine The saw is driven by an electric motor which transmits the power to the chain via a large chain pulley The guide bars that are to be used are specially adapted THE LABELING ON THE MACHINE E LOGOSOL Speed Saw Pod for the Speed Saw and are available in different lengths supplied by LOGOSOL The Speed Saw has no own electrical system but has to be connected to a manual feeder unit ref no 6000 000 6005 or the automatic feeder unit E37 ref no 6600 000 3015 In its basic design the saw has a solenoid valve that controls the oil flow to the bar Besides this the Speed Saw has no own electrical system Relcley jelE Fiskaregatan SE 87133 H rn sand Sweden www logosol se Tillverknings r 20H C Vikt 47 Kg Serie mm IM SE CEE 50Hz 16A 3x400V E8 Art nr 6608 000 0005 NO 50 60Hz 20A 3x230V E8 Art nr 6608 000 0010 TOOLS REQUIRED Allen kev 4 mm 3 16 Allen kev 5 mm 1 4 Combination wrench 10 mm 7 16 Combination wrench 13 mm 9 16 Combination wrench 17 mm 11 16 Screwdriver or something else that is suitable for locking the rotation of the chain pullev ASSEMBLY 1 Fit the motor mount 20 with four M8x20 countersunk Allen screws Use medium strength threadlocker and torque the screws to 25 Nm Then fit the cover plate 18
4. onto the guide rail so that the track in the plastic slide strips clasps the edges of the guide rail Make sure that the slide strips of the Speed Saw shut tightly around the edges of the guide rail in all four corners before guide bar and chain are fitted and the power is connected The Speed Saw can be driven by electric or manual feed In both cases a line holder is fitted to the rear edge of the Speed Saw Read the user manuals for the electric feeder E37 and for the manual feed unit for further instructions on connection and operation The sawmill should be secured to the floor or foundation and equipped with supports under both ends of the guide rail On the side of the feed unit you use the support leg of the feed unit and on the other side of the guide rail the support leg with ref no 6600 000 3001 Before the Speed Saw is removed from the guide rail the power must be disconnected the line holder unscrewed and the guide bar removed FITTING GUIDE BAR amp CHAIN Make sure that the power cable is unplugged e Loosen the guide bar bolts on the top side of the saw until the cover plate comes in such a low position that the guide bar can be inserted Ensure that there is no sawdust between the bar plate and the cover plate The guide bar should be fitted as far in as possible to ensure that the oil hole comes in correct position e Loosen the chain tension knob at the back of the saw about 3 cm 1 2 16 Loosen the e
5. sawing div wood or taking wide cuts Even a low water flow of 1 2 drops per second gives a considerable cooling effect More water cools better of course Solenoid valve oil di saba eS a Ball valve water cooling Ball valve oil lubrication ADJUSTABLE SLIDE PROFILES The Speed Saw has adjustable slide profiles These make it possible to adjust the play between the elecric saw and the guide rail of the Logosol Sawmill Adjustments should only be made when the saw is mounted on the guide rail of the Logosol Sawmill Tighten the screw in each adjusting aluminium profile by turning it clockwise a quarter of a turn at a time as long as the saw slides without difficulty along the whole length of the guide rail When it begins to be difficult to move the saw you loosen the screws a quarter of a turn Note that there should always be a certain degree of play Lateral play has no effect on the result 18 E LOGOSOL Speed Saw SAWING WITH THE LOGOSOL SPEED SAW BEFORE EACH WORK SESSION Make sure that the saw is correctly mounted on the guide rail Make sure that the guide bar and chain are in good condition Fit the saw chain and make sure that it runs easy and is correctly tightened Check the chain oil level KMake sure that the power cable is in good condition Due to the high output of the motor it is imoprtant t
6. 0 Guide bar 70 cm 6608 001 0130 Sawdust guard 6608 001 0120 Right handle 6608 001 0125 Left handle 6608 001 0215 Tube bar nose steering 6608 001 0205 Bracket bar nose steering 6608 001 0210 Magnet holder 6608 001 0225 Magnet bar nose steering 6608 001 0135 Feeder holder 6608 001 0250 Line holder 6605 000 0100 Water cooling 5220 001 0059 Locking handle excentric 6608 001 0110 Right cover plate 6608 001 0115 Left cover plate 6608 001 0140 Knurled knob 6608 001 0005 Cover plate 6608 001 XXXX Cable hook 6608 001 0010 Motor mount 6608 001 0015 Chain tensioner 6608 001 0040 Spacer 12 mm 6608 001 0025 Spacer 5 mm 6608 001 0030 Outer chain guide 6608 001 0035 Chain pulley 24t 6608 001 0020 Spacer 10 mm 6608 001 0045 Washer motor shaft 6608 001 0100 Aluminium profile 6608 001 0105 Slide strip 50 mm 9999 000 6031 Adjusting aluminium profile 6670 001 0006 Locking plate slide strip 6608 001 0075 Bar mount 6608 001 0080 Bar plate 6608 001 0085 Cover plate H LOGOSOL Forward Operator side Backward E LOGOSOL Speed Saw 34 1 0G0SOL Speed Saw MACHINE DESCRIPTION LOGOSOL Speed Saw is a
7. A LOGOSOL E4 E8 SPEED SAW OUTPUT Rated power E4 Speed Saw 4 kW Rated power E8 Speed Saw 8 kW TRANSMISSION Direct drive 24t chain pullev Rotational speed 2850 rpm Chain speed 22 5 m s 74 ft s NOISE LEVELS Sound pressure unloaded 97 0 dB A Sound pressure loaded 102 0 dB A Sound power level 113 0 dB A DIMENSIONS Height 475 mm 1 ft 6 64 Length 860 mm 2 ft 9 64 Width 365 mm 1 ft 2 2 8 Weight 40 47 kg 88 or 104 lbs CUTTING EQUIPMENT Logosol 3 8 Speed Saw guide bar 1 3 Stihl 3 8 Picco Rollomatic 1 3 saw chain 50 70 cm 1 ft 7 16 or 2 ft 3 916 50 70 cm 1 ft 7 16 or 2 ft 3 9 16 E LOGOSOL Speed Saw 21 p LOGOSOL SSS 22 LOGOSOL Speed Saw E Declaration of conformitv Logosol AB Fiskaregatan 2 S 871 33 Harn sand Phone 446 611 18285 herebv guarantees that LOGOSOL Speed Saw with ref no 6608 000 0005 6608 000 0010 6608 000 0015 6608 000 0020 is manufacturedin conformitv with Machinerv Directive 2006 42 EG EMC Directive 2004 108 EG and LVD Directive 2006 95 EG and in accordance with the following harmonized standards EN ISO 12100 2010 EN 60204 1 2006 EN 61000 6 1 3 Mattias Bystr m Product Manager is answerable for technical documentation H rn sand 2013 03 27 Malte Frisk CEO 23 H LOGOSOL H LOGOSOL LOGOSOL SWEDEN Fiskaregatan 2
8. S 871 33 H rn sand Phone 46 0 611 182 85 I Fax 46 0 611 182 89 info logosol se www logosol se 24
9. ail flanges there is risk of the saw unit being thrown out when started Make sure that the power cable can run freely over the entire sawmill length Never step on the cable The power cable should be suspended by a wire above the sawmill The eleectric saw together with the LOGOSOL Sawmill is a one man sawmill Respect the safety distance due to high noise level and risk of a broken chain being hurled out from the guide bar Turn the saw unit off after each saw cut Never work alone and make sure there are other persons within earshot whom you can summon if vou need help Alwavs wear protective clothing and use personal protective equipment Close fitting work overalls are appropriate Never operate the unit wearing loose fitting clothes overall coats or similar Use safetv shoes with high grip soles and steel toecaps Neckerchiefs ties jewellerv or other items that can get caught in the equipment are not to be worn Never stretch over or under the Logosol sawmill s guide rail when the sawmill is in operation Rotating saw chain Risk of cut injuries The saw chain and other rotating parts are accessible on the guide bar side underneath the saw unit on the operator side and in the sawdust duct Wear strong protective gloves Risk of cut injuries when handling the guide bar and the saw chain Cutting equipment can also be hot immediatelv after sawing Never leave the saw unattended with the power cable conn
10. e the right to change the design and form of our products Text Mattias Bystr m Translation Anna Bystr m Olsgren Document Logosol Speed Saw Manual Illustrations Erik Svensson Last revised April 2013 Manual ref no 0458 395 0440 O 2013 LOGOSOL H rn sand Sweden LOGOSOL Speed Saw Table of contents Safety instructions 4 Overview 5 Machine description 9 Tools required 9 Assembly 10 Lifting instructions amp setup 17 Fitting guide bar amp chain 17 Chain lubrication amp water cooling 18 Adjustable slide blocks 18 Sawing with the Logosol Speed Saw 19 Cutting equipment 19 Storing the electric saw 19 Elecrical system 20 Technical data 20 EC Declaration 23 H LOGOSOL SAFETY INSTRUCTIONS Read the entire user manual carefully before using the electric saw Risk of mortal danger if you do not follow the safety instructions LOGOSOL E8 Speed Saw is exclusively intended for rip sawing with the LOGOSOL Sawmill Improper use can cause serious injury Always be concentrated and careful when using this saw unit Fit support legs under the guide rail before pushing the saw unit onto the sawmill Otherwise the LOGOSOL Sawmill will tip over unless there is no load on the log beds Always make sure that the saw unit is pushed fully into position on the guide rail before connecting the power cable If not all four plastic profiles clutches the guide r
11. ected so that unauthorized persons can start it After service the machine should be returned to its original condition Onlv use original spare parts Alwavs disconnect the power before changing guide bar and chain adjusting cleaning or other servicing touching the moving parts of the saw unit lifting the saw unit off the LOGOSOL Sawmill Hearing can be damaged after relatively short periods of exposure to the high frequency noise of the motor and the cutting equipment KEY TO SYMBOLS 9 b B SP For vour own safetv read through the entire user manual carefullv and do not start the ma chine before vou have understood evervthing Use approved ear protectors and protective eyewear Hearing can be damaged even after short periods of exposure Rotating saw chain Make sure that your fin gers never move into the vicinity of the guide bar Never reach over the guide rail Never touch the Speed Saw when it is running This symbol means WARNING Pay particular attention where this symbol appears in the manual text A warning comes after this symbol Pay par ticular attention where this symbol appears in the manual text LOGOSOL Speed Saw 6608 000 0005 E8 Speed Saw 400V 6608 000 0010 E8 Speed Saw 230V 6608 000 0015 E4 Speed Saw 400V 6608 000 0020 E4 Speed Saw 230V 8000 001 000X Motor 4kW 6608 001 000X Motor 8kW 6608 001 0060 Chassis 3008 010 0050 Guide bar 50 cm 3008 010 007
12. hanges If the motor is stored outdoors for a longer period of time vou should check that there is no water in the motor before it is connected to electricitv The motor is equipped with a drain plug 19 H LOGOSOL ELECTRICAL SYSTEM The Speed Saw has no own electrical system but should be connected to a feed unit equipped with a starter The motor is a three phase 220 400V or 400 600V The motor is connected to the phases the standard way depending on which voltage it will be driven by The electric motor is equipped with overheating protection which is connected to the terminal block of the motor It is to be connected to the phase and neutral in the hold circuit Read the instructions for the feed unit that you buy a new power cable to reduce the risk of poor power supply A damaged cable gives you lower output and can damage the motor and the contactors Be careful with the power cable you use for the saw Never step on the power cable or let it be run over by a vehicle Do not use a too long extension cord If you use a 25 m 82 ft long power cable it can be 2 5 mm 1 8 If you use an extension cord that is longer than 25 m it should be 4 mm 3 16 LOGOSOL supplies extension cords that are 2 5 and 4 mm with 16A socket and plug The Speed Saw consumes a lot of electricitv when it is heavy loaded so it is crucial that the electrical equipment is in perfect condition We recommend TECHNICAL DAT
13. hat vou immediatelv stop sawing when the chain loses its sharpness Even a few seconds of sawing with a dull chain will expose in the bar to heavy wear and the chain will be overheated after which it cannot regain its sharpness STORING THE ELECTRIC SAW Cover the Speed Saw and the feed unit with a rain cover if the saw is stored outdoors Emptv the water svstem of water if there is risk of ice formation Vegetable oil can harden over time and cause problems in the oil svstem When vou know that vou are not going to saw for a couple of months emptv the bottle of vegetable chain oil and fill it with a small amount of mineral oil AFTER EACH WORK SESSION e Disconnect the power by pulling out the plug of the power cable e Remove the saw chain e Clean the Speed Saw with compressed air e g and Universal oil ref no 9999 000 5105 The oil is dirt dissolving and protects against corrosion A clean motor is more easilv cooled and is more efficient e Tip Grind the bar rails often to prevent them from being worn more on one side than the other This way the bar will last longer and you get a better sawing result For information read the booklet The Handbook for Your Cutting Equipment handbok f r din sk rutrustning which can be downloaded free on LOGOSOL website http www logosol se Electric motors should be stored in heated premises to prevent condensation in the motor housing which occurs due to temperature c
14. s and M6 flange nuts Then fit the bar nose steering magnet 10 with a M4x8 Allen screw incl washer Set the angle of the bar nose steering tube so that it is horizontally level by turning the left handle 6 and then tighten the screws on the side of the handle Add a third M6x12 Allen screw with washer at the front edge of the handle Then fit an M6x20 hex flange bolt in the threaded hole under the bar nose steering tube Let there be a play of approx 5 mm approx 1 4 at the front edge to prevent the sawdust guard from being clamped Fasten the bolt with a M6 flange nut 13 9 Rivet the bottle holder on to the motor On the 8kW motor two holes have to be drilled On the 4kW motor you can use one of the holes that holds the fan cover in position and only one new hole has to be drilled Put the bottles in the holder The oil bottle with a black cap and a solenoid valve is to be placed to the left and the water bottle with a blue cap to the right Then connect the plug for the solenoid valve 10 Let the tubes run along the right side of the motor Insert the tube from the oil container into the hole closest to the guide bar and the tube from the water container into the hole next to it 14 SSS LOGOSOL Speed Saw SSS eae P Q RRR ce i a Set bbb i ii OS q 11
15. s by fitting two M6 square nuts in each alu profile and then fasten them by using M6x16 hex screws incl washers Then tighten the screws in the cover plates 6 Fit the feeder holder 11 to the chassis 2 with three M6x10 hex screws incl washers Then screw the knurled chain tension knob 17 on the bolt protruding from the back of the chassis 12 LOGOSOL Speed Saw 7 Fasten the cover plate 34 with four M8x35 incl RR washers Do not tighten the screws but let there be _A a play of approx 5 6 mm approx 1 4 between the cover plate and the bar plate 33 Then fit the Ps lt A right and left handles 5 6 using M6x12 Allen j screws incl washers Do not tighten the screws in i the left handle 8 Fit the bar nose steering tube 7 using two M6x12 Allen screws incl washers Let the tube run through the hole in the sawdust guard 4 and fit the sawdust guard to the right handle of the saw 5 using an excentric locking handle 14 and two M6 nuts Then fit the bar nose steering bracket 8 using two M6x12 Allen screws incl washers and fasten the magnet holder 9 with two M6x16 hex flange bolt
16. with two countersunk Allen screws Position no in the exploded views 2 Place the chassis 2 on the motor mount 20 and fit the chain tensioner 21 to the chassis according to the figure to the left Then fasten the full thread M6x60 bolt in the chain tensioner using an M6 nut Screw the three components together using four excentric locking handles 14 10 LOGOSOL Speed Saw 3 Fit spacers pulley etc in following order spacer 12 mm 22 spacer 5 mm 23 chain guide 24 chain pulley 25 chain guide spacer 12 mm spacer 5 mm spacer 10 mm 26 and last the motor shaft washer 27 Lock the pullev with a screwdriver or other suitable tool and fasten everything with an M10x30 hex screw Use medium strength threadlocker and torque the screw to 25 Nm 4 Fit the bar mount 32 and the bar plate 33 with two countersunk M6x16 Allen screws Use medium strength threadlocker Then fit the right and left cover plates 15 16 with M6x10 hex screws incl washers Do not tighten the Screws 11 H LOGOSOL 5 Fasten the complete alu profile
17. xcentric locking handles and push the motor towards the guide bar e Hold the chain so that it forms a loop e Fitthe chain on the chain pulley under the motor The outer chain guide has a recess on which the chain is placed e Gently pull the chain so that the pulley rotates The cahin will then come in position on the teeth of the pulley e Fitthe chain in the groove in the guide bar and push the moter back in place Tension the chain a final time using the chain tension knob e Secure the motor by tightening the four excentric locking handles Correct chain tension If you hold the chain between your thumb and forefinger you should be able to pull the chain out from its groove at the middle point of the bar When releasing the chain it should snap back einto tha groove in Go lars eccccccccccccccccce 17 CHAIN LUBRICATION amp WATER COOLING In its basic design Logosol Speed Saw has a solenoid Oil pump and automatic water cooling valve that controls the supplying of oil The oil runs If you want to upgrade your Speed Saw to get down on the bar by gravity feed The flow is adjusted by even better capacity it can be supplemented with a a ball valve Only use Arborol chain oil or other viscous mechanical oil pump ref no 9999 000 9999 oil as the supplving of oil is done without oil pump The water cooling is completelv manuallv controlled Open the ball valve to make water drip down on the bar when vou are
Download Pdf Manuals
Related Search
Related Contents
Manual del propietario - Homocrisis by Toshiba Calefacción & Aire pochette dossier ss photo DV+fiche parcours prof. TM-2-4 Deutsch Gigabyte Mika M2 Black, White Yamaha DVD-S559 Owner's Manual Exercise 3 - Bryn Mawr Computer Science Kensington K39797US PCISA-9102 Half-Size CPU Card User Manual Advanced Cable Technology RL3901 fiber optic cable Graco 311828H User's Manual Copyright © All rights reserved.
Failed to retrieve file