USER MANUAL - Electra Light
Contents
1. 1 Manual unlock 14 Screw 16 Menu 19 Timer 17 Up 20 Manual lock You can use fogger timer on the rear to achieve continuous fog output and emission at intervals You can use fogger timer on the rear to achieve continuous fog output and emission at intervals Warming up means the fogger is heating Ready to fog means the fogger can emit the fog Timer volume 1 100 press the button MENU it shows Timer volume 1 100 you can set the fog output volume from small to big by the buttons UP or DOWN Interval set 1S 900S press the button MENU till it shows Interval set 1S 900S you can set the interval fog emission time from 1 900 seconds by the buttons UP or DOWN Duration set 1S 200S press the button MENU it will show Duration set 1S 200S you can set the continuous fog output from 1 200 seconds by the buttons UP or DOWN TIMER when the interval time and duration time set press the button TIMER the fogger starts to work Duration Interval time you have just set shows in the LCD display of the control box Volume out 1 100 when the fogger ready to emit press the Manual Lock button it shows Volume out 1 100 adjust the fog emission volume from 1 small to 100 big by the buttons UP or DOWN the fogger emits as adjusted push the MANUAL LOCK button for a second time it holds the emission of the fogger Non stop burst when the fogger ready to emit press the button MANUAL LOCK it shows Non stop burst the fogger wi2. USER MANUAL FOGGER 3000DMX CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing Make sure of the voltage on your end suitable for the unit For your own safety please read this user manual carefully before you initially start up Every person involved with the installation operation and maintenance of this device has to be qualified follow the instructions of this manual 1 INTRODUCTION Thank you for having chosen club smoke DMX series You will see you acquired a powerful and versatile device Unpack your item Before you initial start up please make sure that there is no damage caused by transportation Should there be any consult your dealer and do not use the device 2 SAFETY INSTRUCTIONS If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Always plug in the power plug least Make sure that the power switch is set to OFF position before you connect the device to the mains Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Make sure that the available voltage is not higher than stated on the rear panel Make sure that the power cord is never crimped or damaged by sharp edges Check the d
3. evice and the power cord from time to time CAUTION Before filling the machine disconnect from mains Never drink fluid or use it on the inside or outside of a human body If fluid gets in contact with skin or eyes rinse thoroughly with water If it is necessary call a doctor immediately DANGER OF EXPLOSION Never add flammable liquids of any kind to the fog liquid Keep device upright Never aim the output nozzle directly at people or at open flames DANGER OF BURNING Keep minimum distance of 50 cm to nozzle Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord Keep away children and amateurs Never leave this device running unattended 3 FEATURES Ideal for party rooms or small discotheques Powerful output With remote control Quality thermostat Overheat protective switch Constant and steady output fog DMX 512 protocol controlling the fog output RE MIRROR PIPING MAKING PIPES NON BLOCKED e LECTRONIC TEMPERATURE CONTROL ADJUSTING THE TEMPERATURE AT A STEADY LEVEL AND UNNECESSARY TO HEAT AGAIN AND AGAIN 4 Fogger juice Hpo 5 Tank 3 Aluminium Rod 6 Handle 2 Housing t Nozzle 7 Control box O O O O 8 Power supply R EA ED usss Sb Ga 14 DMX input 15 DMX output 9 Fuse 10 Rocker 11 Wireless 12 ON OFF 13 Dip switch switch remoter Remoter When the fogger finishes warming u
4. ll emit continuously Manual unlock press the button MANUAL UNLOCK the fogger will emit hold pressing and the fogger will emit continuously DMX address 001 512 press the button MENU it will show DMX512 001 512 you can set the desired DMX address by the buttons UP or DOWN CAUTION The escape nozzle will heat up during operation Therefore do not touch the nozzle until it has cooled down completely Cleaning the heating element The heating element should regularly be cleaned every 30 operational hours in order to avoid clogging Use haze machine cleaner available at your dealer Procedure Fill cleaner into empty tank Run the machine several times in a well ventilated room only The number of repetitions depends on the pollution level of the vaporizing elements After use clean all remaining cleaner and rinse the tank thoroughly There are no serviceable parts inside the device except for the fuse Maintenance and service operations are only to be carried out by authorized dealers Replacing the fuse If the fine wire fuse of the device fuses only replace the fuse by a fuse of same type and rating Before replacing the fuse unplug mains lead Procedure Step 1 Open the fuse holder on the rear panel with a fitting screwdriver Step 2 Remove the old fuse from the fuse holder Step 3 Install the new fuse in the fuse holder Step 4 Replace the fuse holder in the housing Should you need any spare parts please use genuine part
5. p ready to emit the blue led at the back of the item lights up 4 STARTING OPERATION 1 DMX protocol Install the device on a plane surface The fluid tank of the device needs to be filled with standard fogger fluid before starting up operation and always disconnected from the mains as fluid could be spilled We recommend high quality Glow fogger fluids You must not use substances that are classified as dangerous working material or inflammable fluids If fluid should get into the interior of the device disconnect from mains immediately and consult a technician Switch the device on via the power switch DMX 512 connection connection between fixtures The wires must not come into contact with each other otherwise Occupation of the XLR connection If you are using controllers with this occupation you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain If you wish to connect DMxX controllers with other XLR outputs you need to use adapter cables Building a serial DMX chain Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect one output with the input of the next fixture until all fixtures are connected Caution At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 resistor between Signal and Signal into a 3 pin XLR plug and plug it in the DMX output of the last fixtu
6. re Connection with the mains Connect the device to the mains with the enclosed power supply cable Addressing After you connect the fogger to the mains the dip switch on the rear allows you to assign the DMX fixture address which is defined as the first channel from which the item will respond to the controller If you set for example the address to channel 7 the item will use the channel 7 for control Please be sure that you don t have any overlapping channels in order to control each item correctly and independently from any other fixture on the DMX data link If two three or more item are addressed similarly they will work similarly Press the dip 1 to ON position other OFF and the fogger is at DMX mode 2 Wireless remote control Connect the remote control box receiver to the three pin socket on the rear of the fogger and then you can use the wireless launcher to on off emit the fog 3 ON OFF control Connect the remote control box to the three pin socket on the rear of the fogger and then you can press the button on the box to on off emit the fog After a certain warm up time the device is ready to operate Upon warming up the stand by lamp red LED of the remote control lights up When the geen led lights up the fogger is ready to emit and by switching the control box the fogger starts emission The temperature is regulated by a high quality thermostat 4 fog timer _ 15 Lcd display 18 Down 2
7. s If the power supply cable of this device will be damaged it has to be replaced by a special power supply cable available at your dealer If defective please dispose of the unusable device in accordance with the current legal regulations Should you have further questions please contact your dealer TECHNICAL SPECIFICATIONS Power supply 220 V AC 50 Hz Fuse 250V 15A Power consumption 3000 W Warm up time approx 10 min Fog output 40 000 cuft min Tank capacity 10L Dimension 660 360 300mm Weight 16 kgs Please note Every information is subject to change without prior notice
Download Pdf Manuals
Related Search