LED Message Board User Guide LED Message Board User Guide
Contents
1. S L E D LED Message Board User Guide 2 Please change the date line with the rightmost module next to the all red module 4 The test of power supply 1 if the power indicator of power supply is bright all the time it indicate good working condition 2 the normal output voltage is DC 5V 3 if the output voltage is out of range or unstable change the power supply F packing list 1 LED message board 2 Three meters of power cord 3 one USB date cable 4 one optical disc 5 one set of wire rope2. J S L E D LED Message Board User Guide LED Message Board User Guide A Description Led message board is also named electronic display screen which has high brightness low power consumption long life and stable performance B Parameter LED Board Dot Pixel Total View Max Product Model Dimension Intensity Voltage Faia Patch Color Pixel Angel Power mm JE P10R 5416 410 1370 32 128 200W Single H1209 AC JE P10R 7821 530 1970 P10 GR 48 192 1200 cd m 600W V60 110V JE P10R 10429 730 2650 64 256 800W Not about product model JE P10R XXXX the JE stands for our company P10 is P10 module R is red XXXX is the dimension of led message board that include length and height C manual of the software Attention The software uses USB 2 0 Flash Drive to upload the program setting How to edit display content and upload to the LED Message board Step One After successfully installing LEDShowTW 2011 insert a USB Drive into computer The USB drive must have a minimum of 2MB space Step two Click open the LEDShowTW 2011 and select Setup and select Set Screen Parameters In the Next Dialog Input the Password 168 By LedshowTW Editing System 2011 File Edit Beto Send Lenguege Help D ih Beer ATA Eitd Crin YD Ye fee Password dialog box Display list Reset Screen Parameters i R Please enter password i Pr Adjust the brightness je Correction time Software Boot Cancel Software Shutdown S
3. Text 1 Dial 1 Time 1 Image Text 1 Mame Image Text 1 3 Ajaj t 4 x k 1 Step Five Once finish setting Click Y to save the program to USB drive USB drive is not included in package D Attention for the software 1 After the program is downloaded to the USB drive do not change any document in the USB drive 2 The parameter that has been set up must match with led message board otherwise the new program cannot be displayed properly 3 The program will upload automatically when insert the USB drive into the USB port on the LED Message board Unplug the USB drive immediately after upload program 100 E Common problems and examining methods 1 The led message board does not turn on 1 please check if the power supply is normal 2 please check if the controller is working or the power indicator light with controller is on 2 A part of the led message board is not working 1 please check if one individual power supply is working properly 2 please check if the data line connection is correct 3 please check if the wiring from power supply is not loose 4 If a 4x8 array of LED modules does not display normally please check if the modules is good 5 when you notice low brightness for partial area of led message board use a millimeter to check if the AC input and DC output is normal 3 There is any line of message board is all red 1 Please change the right most module next to the all red module J
4. tep Three In the Parameter Setting dialog setup the JS LED Message Board parameter J S L E D LED Message Board User Guide e Under Screen parameters select the Controller BX 4U1 from the list Select Width Pixel and Height Pixel refer to Total Pixels in the Parameter table for specific model Unmatched parameters will cause abnormal display Click Save and then click Close By Parameters Setting OED BX 4U1 1 Maximum pixels ratbiadlh bind Build Address Single color 24K dots 24576 RE Two colors 12K dots 12288 2 Display Moda Controler i Single color ex 4ur Lise storage dev ISS6 16 765 32 512 48 384 64 Two colors T68 16 304 32 om Outdoor P10 2 8 lt Save Scan Here onty for popular configuration of three LED units For quickly scan Step Four 4 I 1 BF Bee Program In Main Window As is shown below Click Program 1 a you can Click Subtitle ie to add Title Click Image T ext to add Text Click Dial to add Dial Click Time to add Time Click Delete K to delete selected program In the Preview Window you can drag and positino the Object where you want to place or you can edit the x or y position to move the object or change the width or height of the object in the preview window Do not overlap objects in one display screen J S L E D LED Message Board User Guide V 1 H 4 SS Frogram 1 Subtitle 1 Image
Download Pdf Manuals
Related Search