User Guide NuTone CV654 and STDKIT200 (30042402 revF
Contents
1. 1140 Tristar Drive Mississauga Ontario L5T 1H9 www nutone ca Released August 2011 Product specifications subject to change without notice REPLACEMENT PARTS AND REPAIRS In order to ensure your unit remains in good working condition you must use Broan Nutone genuine replacement parts only Broan Nutone genuine replacement parts are specially designed for each unit and are manufactured to comply with all the applicable certification standards and maintain a high standard of safety Any third party replacement part used may cause serious damage and drastically reduce the performance level of your unit which will result in premature failing Broan Nutone recommends to contact a certified service depot for all replacement parts and repairs2. THIS WARRANTY BROAN NUTONE CANADA SHALL NOT BE LIABLE FOR INCIDENTAL CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE Please do not return your unit to place of purchase Please visit www nutone ca for your closest service center You may also call 1 888 882 7626 for the name of an authorized representative in your area This warranty supersedes all prior warranties Warranty service is to be completed by an authorized Service Center designated by Broan NuTone Canada Where applicable in home service will be made available only in areas where a contracted service provider offers service If in home service is not available the product will be repaired or replaced at Broan NuTone Canada s discretion by the nearest authorized service provider The unit removal and reinstallation works are under the customer responsibility and Broan NuTone Canada cannot be charged for them To qualify for warranty service you must notify Broan NuTone Canada at the address or telephone number stated below We will then forward you the authorized service depot in your area You will be required to present evidence of the original purchase date IF YOU NEED ASSISTANCE OR SERVICE For the location of your nearest Broan NuTone Canada Inc dealer Dial Toll Free 1 888 882 7626 Please be prepared to provide Product model number Date and proof of purchase The nature of the difficulty Broan NuTone Canada Inc
3. has been cleared Insert hose end into any inlet with power unit running place the palm of your hand over the opposite end of the hose When you can feel the suction increase hold your hand over the hose end for a few seconds and then quickly remove your hand This procedure repeated several times should clear the obstruction If the blockage is not cleared contact your nearest Service Center Check all wall inlet covers to be sure they are closed and sealed tightly Replace defective wall inlet Turn the unit off by using the power switch on the unit Check the overcurrent protector button located on the left side of the power unit push to reset the system Turn unit back on Replace fuse or reset circuit breaker on house electrical panel Turn the unit off by using the power switch on the unit Wait 30 minutes to let the unit cool down Turn unit back on Replace hose as required Power unit fails to stop when the hose is removed An electrical short has occurred somewhere in the system 42 A complete check of all wall inlets and power unit low voltage control leads connections Contact your authorized Service Center BROAN NUTONE CANADA INC CENTRAL VACUUM POWER UNIT LIMITED LIFETIME WARRANTY Broan NuTone Canada warrants to the original consumer purchaser that its central vacuum power unit will be free from defects in materials and workmanship for as long as you own your home in whi
4. NuTone CENTRAL VACUUM POWER UNIT Z HOUSEHOLD TYPE A CV654 STDKIT200 MODEL NO SFDB DB E gt AB0018 HOMEOWNERS OPERATING INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS 1 888 882 7626 Broan NuTone Canada Inc To register this product visit www nutone ca 1111 Mississauga Ontario www nutone ca 118i 9 30042402 Rev F 77237 IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE When using an electric appliance basic precautions should always be followed including the following WARNING A TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR PERSONAL INJURY Do not use on wet surfaces or outdoors Do not allow to be used as a toy Close attention is necessary when used by or near children Use only as described in this manual Use only manufacturer s recommended attachments Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow Keep hair loose clothing fingers and all parts of body away from openings and moving parts Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use without dustbag or filter in place Do not use to blow leaves or debris Do not vacuum liquids or fine powders such as drywall dust Do not put any object on the unit Ensure air flows freely around exhaust outlet Do not install the unit h
5. ccessible location for cleaning and maintenance e Locate the power unit within 6 feet of a grounded electrical outlet The power unit requires a 120 VAC power source e Do not locate the power unit close to a source of extreme heat i e water heater or in an area with a high ambient temperature i e attic furnace room e Do not locate the power unit where the temperature can drop below 0 C 32 F e Ifthe power unit is located in a closet or a small utility room make sure the area is well ventilated i e with door louvers NOTE Visit www nutone ca for the central vacuum system installation instructions 9 2 MOUNTING POWER UNIT o7 Ua aie y Make sure to assemble the wall mounting MINIMUM WALL CLEARANCE DIMENSIONS 14 min bracket with the screws directly onto a ii wall stud for a solid installation PVC TUBING STRAP 1 Carefully remove debris pail from power unit Make sure bag is properly installed in power unit Remove accessories and installation kit Securely reinstall pail CEILING 2 Install the 3 way elbow on the back of the power unit and press firmly do not glue 12 MINIMUM TO CEILING Remove the plastic cap from the inlet ir WA BRACKET opening only if your installation requires the il EXHAUST connection into both inlets E 3 WAY ELBOW DO NOT GLUE REMOVE PLASTIC CAP IF NEED BE FRONT VIEW 3 Install mounting bracket o
6. ch it was originally installed with the exception of the motor and electronic components which will be warranted for three 3 years The first year of this warranty covers the parts and labor in an authorized service center THERE ARE NO OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE During these time periods Broan NuTone Canada will at its option repair or replace the power unit or part without charge which is found to be defective under normal use and service THIS WARRANTY DOES NOT APPLY TO THE INSTALLATION OR THE PARTS USED IN THE INSTALLED TUBING SYSTEM All central vacuum hoses electric or air driven brushes filters attachments and accessories are warranted for one 1 year from the original purchase date with the exception to consumables such as light bulbs and belts This warranty does not cover a normal maintenance and service or b any products or parts which have been subject to misuse negligence accident improper maintenance or repair other than by Broan NuTone Canada or an authorized representative faulty installation or installation contrary to recommended installation instructions The duration of any implied warranty is limited to the period as specified for the express warranty BROAN NUTONE CANADA S OBLIGATION TO REPAIR OR REPLACE AT BROAN NUTONE CANADA S OPTION SHALL BE THE PURCHASER S SOLE AND EXCLUSIVE REMEDY UNDER
7. decrease of vacuum occurs 2 Power unit does not start or stops suddenly The plastic cap is not installed on the unused inlet Debris pail or disposable bag is completely full Obstruction in the hose A blockage in the hose can be determined by inserting the hose into any wall inlet and while power unit is running check each additional inlet for normal suction by holding the palm of your hand over the open inlet If normal suction is felt at all other inlets insert the hose into a second inlet If the blockage still exists it is located in the hose However if the blockage does not occur when the hose is changed the blockage is probably located in the tubing system leading to the original inlet Obstruction in the tubing system inside the walls Wall inlet cover not properly sealed Defective inlet Check other wall inlets Power unit overcurrent protector has been activated Blown fuse or tripped circuit breaker on house electrical panel Thermoprotector has been activated Defective hose e Place the included plastic cap on the unused inlet opening e Change disposable bag or empty debris pail as described on page 4 NOTE Clean secondary filter if necessary e Disconnect the hose from the wall inlet and insert a blunt instrument into the hose slightly smaller in diameter such as a flexible garden hose Push the garden hose through the cleaning system hose until the obstruction
8. e transported to the power unit where they remain in a bag or in the debris pail NOTE The rocker switch on the front of the power unit can be used to turn the power unit on Use the cleaning tools as you would for any other vacuum cleaner Avoid picking up pine needles coffee sticks and other similar objects These kinds of objects may become lodged in the hose or tubing 2 VACUUM POWER CONTROL The hose handle is equipped with a control ring to regulate the air flow The control ring covers a bleeder hole Open the hole to reduce the suction for cleaning draperies small rugs and other light fabrics Some very thick plush carpets with high density yarns also aAooos ConTROL require reduced suction to make the nozzle easier to RING push Be sure to close the control ring completely over the hole to produce the maximum power required for most other cleaning tasks 3 WHEN TO CHANGE BAG OR EMPTY DEBRIS PAIL With a 6 U S Gallons capacity under normal conditions the bag debris pail requires changing emptying approximately twice a year If the bag debris pail is filled you will notice a complete loss of vacuum in the system Unless this loss of vacuum is caused by a blockage in the system changing the bag or emptying the debris pail will solve the problem NOTE Even if not filled to capacity if the bag seems tightly stretched when removing the debris pail changing the bag will prevent it from tearing The access
9. n a wall stud within 6 feet of a grounded electrical outlet at the distances specified on illustration at right 18 MINIMUM ABOVE FLOOR Ensure that wall between mounting bracket and inlet is straight and leveled FLOOR y y AD0040A 9 POWER UNIT INSTALLATION conrT p RETAINING SCREW LOCATIONS 4 Use the mounting bracket as a template to mark the position of its screws Drill the MounmNe BRACKET upper and lower screw holes into the stud using a 3 16 drill bit 5 Using a Phillips screwdriver secure the mounting bracket to the wall with 2 no 14 x 2 screws included Make sure that the bracket is tight against the wall 6 Hang the power unit by inserting its back hook into the center opening of its mounting bracket wacuer screw WASHER SCREW Make sure hook is securely engaged in bracket LOCATION INSTALLED Secure the power unit to the mounting bracket with the provided no 6 x 3 8 screw and washer into the small remaining hole using a Phillips top of tHe Top oF THE screwdriver see illustrations at right UNIT UNIT ADO041 AD0042 7 Run house vacuum line up to the 3 way elbow behind the power unit Secure house vacuum line to the appropriate 3 way elbow opening with PVC glue do not glue the 3 way elbow to the power unit 8 Connect muffler if desired and exhaust tubing to exhaust outlet on top of the power unit The exhaust should not be vented int
10. o a wall ceiling or concealed space in the house Exterior vented exhaust lines should end using model V142 wall cap NOTE Exhausting the power unit to the outside is recommended for optimal performance but is not required 9 Once everything is in place secure the piping near the elbow to the wall using the included PVC strap A00031 10 GROUNDING INSTRUCTIONS N WARNING Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded Do not modify the plug provided with the appliance if it will not fit the outlet have a proper outlet installed by a qualified electrician This appliance must be grounded If it should malfunction or break down grounding provides a path of least resistance for electric current to reduce the risk of electric shock This appliance is equipped with a cord having an equipment grounding conductor and grounding plug The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances This appliance is for use on a nominal 120 volt circuit and has a grounding attachment plug that looks like the plug illustrated below Make sure that the appliance is connected to an outlet having the same configuration as the plug No adapter should be used with this ap
11. orizontally Do not use the pail as a wash pail Do not use the pail as a stool Turn off all controls before unplugging Use extra care when cleaning on stairs Avoid picking up sharp objects Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present Do not use with damaged cord or plug If appliance is not working as it should if it has been dropped damaged left outdoors or dropped into water return it to a service center Do not unplug the unit by pulling on cord To unplug grasp the plug not the cord Do not handle plug or appliance with wet hands Connect to a properly grounded outlet only See grounding instructions on page 9 Any servicing other than that recommended in this manual should be performed by an authorized service facility We recommend that your unit be inspected by a specialized technician once a year SAVE THESE INSTRUCTIONS 20 1 OPERATION The power unit is located away from the everyday living areas of your home usually in the garage basement or utility room Through a network of strong lightweight tubing the power unit connects to inlets strategically placed throughout your home When you are ready to clean attach the wand and cleaning tool onto the end of the hose Open the inlet cover and insert the end of the hose into the inlet Use the ON OFF switch on the hose handle to activate the power unit As you vacuum dirt and dust ar
12. ory kit is included only with the STDKIT200 model See section 11 on page 10 for more details In order to use the debris pail to collect debris the optional permanent filter has to be installed in the power unit see permanent filter instructions on page 5 z9 4 DETAILED VIEW ROCKER SWITCH EXHAUST OUTLET VACUUM CHAMBER INLET INLET CHAMBER BAG ADAPTER DISPOSABLE BAG __ NY LATCH DEBRIS PAIL Pe 5 BAG REPLACEMENT 1 To remove the disposable bag release both latches on sides of the unit by pulling out and then pushing up Remove the pail from unit Grasp the edges of the bag collar and pull down The bag will slide off easily Do not pull on the bag 2 Unfold new bag 3 Grasp collar where indicated on the bag and insert over bag adapter Be careful not to tear the bag Ensure that the collar is positioned between the taper ring and the bag stopper on the bag adapter see illustration below Put the pail back in its place TAPER RING AQ0024 BAG STOPPER NOTE A set of 3 replacement bags model 391C may be purchased from your local Broan NuTone Sales Outlet To locate your nearest Broan NuTone Sales Outlet call toll free 1 888 882 7626 sa 6 PERMANENT FILTER OPTIONAL The optional permanent filter can be used with or without the disposable bag This filter protects the motor and stops small particles from escaping to the
13. outside of the power unit wihout the need to replace it The filter can be removed by means of a pull tab for cleaning if need be Be sure to reinstall properly Appropriate location is critical to insure proper protection of the motor 6 1 INSTALLING FILTER Squeeze the filter in order to place it over the bag adapter A Let the filter prop against the unit wall by releasing the squeezing pressure Make sure to place the rigid ring between the upper rib B and the three bottom posts C to ensure proper sealing A00028 Make sure the filter is installed so that the pull tab D is accessible for future filter removal D AA0005 6 2 REMOVING FILTER Remove debris pail and disposable bag Using pull tab on edge of filter pull and loosen filter from inlet chamber wall by squeezing it on itself Then carefully remove it from the unit 6 3 CLEANING FILTER Simply brush filter clean If the filter is excessively soiled wash in a mild detergent and let it dry completely before putting it back in its place 07 U oN Ensure that filter is completely dry before reinstalling NOTE The permanent filter model PF450 may be purchased from your local Broan NuTone Sales Outlet To locate your nearest Broan NuTone Sales Outlet call toll free 1 888 882 7626 7 HOW TO EMPTY DEBRIS PAIL To empty the debris pail release both latches on sides of the unit by pulling out and then pushing up Holding the pail by the latches l
14. ower it from unit Carry pail to trash receptacle and dispose of debris Put the pail back in its place 8 SECONDARY FILTER A secondary safety filter located at the top of the vacuum chamber provides protection against dirt being pulled into the motor if the disposable bag or permanent filter should accidentally be torn This filter should be checked and cleaned if necessary when replacement bag is installed or when optional permanent filter is removed for cleaning Simply brush filter clean If the filter is excessively soiled wash in a mild detergent and let it dry completely before reinstalling o7 Un aie Operating the power unit without the secondary filter will void the warranty 8 1 REMOVING FILTER Remove debris pail and disposable bag or permanent filter Remove both locking sleeves from the retaining hooks Carefully pull filter A RETAINING down to remove 8 2 REINSTALLING FILTER SECONDARY To reinstall the secondary filter reverse the steps Re FILTER described above LOCKING NOTE A replacement secondary filter part no 10941310 may be purchased from your local Broan NuTone Sales Outlet To locate your nearest Broan NuTone Sales Outlet call toll free 1 888 882 7626 When performing installation servicing or cleaning the unit it is recommended to wear safety glasses and gloves 9 POWER UNIT INSTALLATION 9 1 LOCATING THE POWER UNIT e Locate the power unit away from the general living area in an a
15. pliance 1 Using pliers install both crimp connectors included to low voltage wire 22 gauge minimum 2 conductor model V133 not included 2 Connect low voltage wire to tabs located on outside of the power unit 3 The power unit is equipped with a 6 foot grounded cord Plug cord into 120 volt grounded receptacle CRIMP CONNECTORS POWER UNIT LOW VOLTAGE TABS OVERCURRENT PROTECTOR BUTTON GROUNDED OUTLET BOX GROUNDED OUTLETS LS GROUNDING PIN Mobe V133 22 2 LOW VOLTAGE WIRE 3 gt To OTHER ai tte Oe oe INLET INLET AE0031 NOTE INLET LEADS TO BE CONNECTED TO POWER UNIT LOW VOLTAGE TABS USING CRIMP CONNECTORS INCLUDED AND LOW VOLTAGE HARNESS 219 11 ACCESSORY KIT MobDEL ACCESSORY KIT CV654 NOT included STDKIT200 Included Accessory kit includes e Multi Surface brush for carpet tile wood and ceramic e 30 Low voltage crushproof hose with 360 rotating handle Deluxe hose hanger included e Standard tool set 10 wide hard floor brush with swivel neck Stainless steel ratchet telescopic wand from a collapsed length of 25 to an extended length of 41 Natural bristle upholstery tool Square faced dusting brush 9 crevice tool with notched end Clip on caddy Nee 10 12 TROUBLESHOOTING GUIDE PROBLEMS POSSIBLE CAUSES POSSIBLE REMEDY 1 Loss or e
Download Pdf Manuals
Related Search