KW5262 Wireless VDSL Router User Manual
Contents
1. 3 Select a ETH port as you will You can select ENET1 ENET2 ENETS or ENET4 port as the WAN interface and Default mode as connection mode ethO ethd v jethi ethi eth2 eth2 eth3 eth3 4 Click Apply Save and you ll see the following screen 22 VDSL Router User Manual Interface Name Connection Mode Remove eth0 eth0 VianMuxMode 5 From Advanced Setup click WAN Service to configure a WAN service over the interface you selected Interface Description Type vlan8021p VlanMuxid Igmp NAT Firewall Remove Edit 6 Click Add and you ll see the following screen WAN Service Interface Configuration Select a layer 2 interface for this service Note For ATM interface the descriptor string is portld_wpi_vci For PTM interface the descriptor string is portid_high_low Where portid 0 gt DSL Latency PATHO portid 1 gt DSL Latency PATH1 portid 4 gt DSL Latency PATHO amp 1 low 0 gt Low PTM Priority not set low 1 gt Low PTM Priority set high 0 gt High PTM Priority not set high 1 gt High PTM Priority set eth0 eth0 v 7 Click Next and you ll see the following screen Select PPPoE as WAN service type for example Click Next Select WAN service type PPP over Ethernet PPPoE TP over Ethernet Bridging Enter Service Description pppoe_etho 23 VDSL Router User Manual 8 Enter the user name and password2. 1 Using a telephone line to connect the DSL port of ROUTER to the MODEM port of the splitter and using a other telephone line connect your telephone to the PHONE port of the splitter then connect the wall phone jack to the LINE port of the splitter The splitter comes with three connectors as below LINE Connects to a wall phone jack RJ 11 jack MODEM Connects to the DSL jack of ROUTER PHONE Connecis to a telephone set 2 Using an Ethernet Cable to connect the LAN port of the ROUTER to your LAN or a PC with network card installed 3 Connect the power cable to the PWR connector on ROUTER then plug in the power adapter to the power outlet and then press the on off button FXS1 FXSO BP MINOC Notes Without the splitter and certain situation transient noise from telephone can interfere with the operation of the Router and the Router may introduce noise to the telephone line To prevent this from happening a small external splitter must be connected to each telephone VDSL Router User Manual 4 PC Configuration Guide 4 1 4 2 Local PC Configuration in Windows 95 98 ME XP VISTA 7 1 Inthe Windows task bar click the Start button point to Settings and then click Control Panel 2 Double click the Network icon 3 On the Configuration tab select the TCP IP network associated with your network card and then click Properties 4 Inthe TCP IP Properties dial
3. KW5262 Wireless VDSL Router User Manual VDSL Router User Manual NOTICE This document contains proprietary information protected by copyright and this Manual and all the accompanying hardware software and documentation are copyrighted All rights are reserved No part of this document may be photocopied or reproduced by mechanical electronic or other means in any form The manufacturer does not warrant that the hardware will work properly in all environments and applications and makes no warranty or representation either expressed or implied with respect to the quality performance merchantability or fitness for a particular purpose of the software or documentation The manufacturer reserves the right to make changes to the hardware software and documentation without obligation to notify any person or organization of the revision or change All brand and product names are the trademarks of their respective owners Copyright 2014 All rights reserved VDSL Router User Manual Content Tel FEATURES 2 ssauseececaecnetssnceancassccdtusauesesseens 2 TAE D QA lali aa 2 Pee DSECONPDIAN a 2 RO MIMOS Si ee caen de een eds nee a Den us et ee 2 1 1 4 Network Protocol amp Features nn a 2 kko AMES DADES A Me NN ai 3 LO WO id dota 3 LAR AIRE WA EE id sia bae 4 1 16 Management SUD eee eee 4 CII ODECTAUNG System SUD il 4 TITO MEMOIRE DS a Oe 4 12 PACKET CONTENTS ac a seen eetesne ds 4 1 93 SYSTEM REQUIREMENTS c
4. VPI Range 0 255 VCI Range 32 65535 UNI 3 0 amp 3 1 Signaling ATM AALS Adaption Layer type 5 OAM F4 F5 SIP Voice codecs G 711A u G 723 G 726 G 729 Call waiting Call forwarding VDSL Router User Manual 1 1 7 FIREWALL e Built in NAT e MAC Filtering e Packet Filtering Stateful Packet Inspection SPI Denial of Service Prevention DoS e DMZ 1 1 8 Management Support e Web Based GUI e Upgrade or update via FTP HTTP e Command Line Interface via Telnet e Diagnostic Test e Firmware upgrade able for future feature enhancement 1 1 9 Operating System Support e WINDOWS 98 98 SE e WINDOWS ME e WINDOWS 2000 e WINDOWS XP e WINDOWS VISTA e WINDOWS 7 e Macintosh e LINUX 1 1 10 Environmental e Operating humidity 10 90 non condensing e Non operating storage humidity 5 95 non condensing 1 2 Packet Contents The packet contents are as the following VDSL Router e DSL ROUTER e External Splitter eo Power Adapter e Telephone Line e Ethernet Cable e Antenna Base e CD 13 System Requirements User Manual X 1 X 1 X 1 X 1 X 1 X 2 X 1 X 1 Before using this ROUTER verify that you meet the following requirements e Subscription for DSL service Your DSL service provider should provide you with at least one valid IP address static assignment or dynamic assignment via dial up connection e One or more computers each contains an Ethernet 10 100M Base T
5. communicate with each other at twice the normal rate 54g is a technology that achieves higher throughput with frame bursting With 54g enabled aggregate throughput the sum of the individual throughput of each network client improves by up to 25 in 802 11g only networks and up to 75 in mixed networks containing both 802 11g and 802 11b equipment Set this 54g mode to 54g Auto for the widest compatibility or to 54g Performance for the fastest performance with 54g certified equipment Select 802 11b Only if all user s wireless clients support 802 11b mode only 54g LRS Limited Rate Support is intended to support legacy 802 11b clients that can t deal with access points which advertise supported rates in their beacon frames other than the original 802 11 s 1 and 2 Mbps rates Use 54g LRS only if user can t get a connection with the other three modes The 802 11g standards provide a protection method so 802 11g and 802 11b devices can co exist in the same network without speaking at the same time Do not disable 54g protection if there is a possibility that a 802 11b device will use user s wireless network In Auto mode the wireless devices use RTS CTS to improve 802 11g performances in mixed 802 11g 802 11b networks Turn protection off to maximise 802 11g throughput under most conditions A preamble is a signal that synchronises the timing between two or more wireless devices allowing all wireless systems to recognise the
6. PPPoE through in order to allow LAN hosts to use PPPoE client software on their computers to connect to the ISP via the VDSL Device Each host can have a separate account and a public WAN IP address PPPoE pass through is an alternative to NAT for applications where NAT is not appropriate Disable PPPoE pass through if you do not need to allow hosts on the LAN to use PPPoE client software on their computers to connect to the ISP The PPP IP Extension is a special feature deployed by some service providers Unless your service provider specifically requires this setup do not select it If you need to select it the PPP IP Extension supports the following conditions t allows only one computer on the LAN The public IP address assigned by the remote using the PPP IPCP protocol is actually not used on the WAN PPP interface Instead it is forwarded to the computer s LAN interface through DHCP Only one system on the LAN can be connected to the remote since the DHCP server within the DSL gateway has only a single IP address to assign to a LAN device NAPT and firewall are disabled when this option is selected The gateway becomes the default gateway and DNS server to the computer through DHCP using the LAN interface IP address The gateway extends the IP subnet at the remote service provider to the LAN computer That is the PC becomes a host belonging to the same IP subnet 20 VDSL Router User Manual The DSL gateway bridges
7. address clear the Use Static IP Address option The ISP automatically assigns the WAN connection an IP address when it connects Enable PPP Debug Mode Select this to turn on the debug mode for the PPP connection Bridge PPPoE Frames Between WAN and Local Ports In addition to the VDSL Device s built in PPPoE client you can enable this to pass PPPoE through in order to allow LAN hosts to use PPPoE client software on their computers to connect to the ISP via the VDSL Device Each host can have a separate account and a public WAN IP address PPPoE pass through is an alternative to NAT for applications where NAT is not appropriate Disable PPPoE pass through if you do not need to allow hosts on the LAN to use PPPoE client software on their computers to connect to the ISP The PPP IP Extension is a special feature deployed by some service providers Unless your service provider specifically requires this setup do not select it If you need to select it the PPP IP Extension supports the following conditions It allows only one computer on the LAN The public IP address assigned by the remote using the PPP IPCP protocol is actually not used on the WAN PPP interface Instead it is forwarded to the computer s LAN interface through DHCP Only one system on the LAN can be connected to the remote since the DHCP server within the DSL gateway has only a single IP address to assign to a LAN device NAPT and firewall are disabled when this optio
8. front panel of the DSL router should be on Check that your VPI VCI type of encapsulation and type of multiplexing setting are the same as what you collected from your service provider Re configure DSL router and reboot it If you still cannot work it out you may need to verify these variables with the service provider If the cause is not given above please contact your local service provider 43
9. is number of bytes in the packet size beyond which the gateway invokes its RTS CTS request to send clear to send mechanism Packets larger than this threshold trigger the RTS CTS mechanism while the gateway transmits smaller packets without using RTS CTS The default setting of 2347 which is the maximum disables the RTS threshold mechanism A delivery traffic indication message DTIM also known as a beacon is a countdown informing wireless clients of the next window for listening to broadcast and multicast messages When the gateway has broadcast or multicast messages for its clients it sends its next DTIM message with this 31 VDSL Router Beacon interval XPress Technology 54g mode 54g TM protection Preamble Type User Manual DTIM interval value The clients hear the beacons and awaken as needed to receive the broadcast and multicast messages The amount of time in milliseconds between beacon transmissions each of which identifies the presence of an access point By default wireless clients passively scan all radio channels listening for beacons coming from access points Before a client enters power save mode it needs the beacon interval to determine when to wake up for the next beacon and learn whether the access point has any messages for it User can enter any value between 1 and 65535 but the recommended range is 1 1000 XPress Technology is a feature in which two of our devices can
10. machines Mixed WPA42 WPA PSK WEP open and WEP shared WEP is an encryption scheme that is used to protect user s wireless data communications WEP uses a combination of 64 bit keys or 128 bit keys to provide access control to user s network and encryption security for every data transmission To decode a data transmission each wireless client on the network must use an identical 64 bit or 128 bit key WEP is an older wireless encryption method that is not as hard to break as the more recent WPA 802 1x In 802 1x also Known as RADIUS a separate machine called an authentication server receives a user ID and password It grants or denies access based on whether the ID and password match any entries in its account list User can optionally enable WEP encryption with this option Because it requires a separate machine acting as the authentication server 802 1x is most often used in business environments 35 VDSL Router User Manual WPA WPA is a more recent encryption method that addresses many of the weaknesses in WEP Any client capable of WPA encryption should use it instead of WEP WPA PSK This is WPA encryption combined with a pre shared key PSK which is a text string known only to the gateway and authorised wireless clients The gateway rejects the login if the client s PSK does not match WPA2 WPA2 is a more advanced encryption method than WPA Because it is a more recent standard some of
11. network interface card NIC e A hub or switch if you are connecting the device to more than one computer e For system configuration using the supplied web based program A web browser such as Internet Explorer v5 0 or later or Netscape v4 7 or later 1 4 Factory Defaults The device is configured with the following factory defaults P Address 192 168 31 1 e Subnet Mask 255 255 255 0 eo User Name admin e Password admin e VPI VCI According to local information 1 5 Warnings and Cautions eo Never install telephone wiring during storm Avoid using a telephone during an electrical storm There might be a risk of electric shock from lightening VDSL Router User Manual e Do not install telephone jacks in wet locations and never use the product near water To prevent dangerous overloading of the power circuit be careful about the designed maximum power load ratings Not to follow the rating guideline could result in a dangerous situation Please note that telephone line on modem must adopt the primary line that directly outputs from junction box Do not connect Router to extension phone In addition if your house developer divides a telephone line to multi sockets inside the wall of house please only use the telephone that has connected with the splitter of DSL Router when you access the Internet Under the above condition if you also install telephone with anti cheat dial device please pull out this k
12. start of transmission 32 VDSL Router User Manual 5 3 3 Security This page allows you to configure security features of the wireless LAN interface You may set up configuration manually or through WiFi Protected Setup WPS 1 Click Security of Wireless item and you ll see the following page WPS Setup Enable WPS Disabled vi Manual Setup AP You can set the network authentication method selecting data encryption specify whether a network key is required to authenticate to this wireless network Click Apply Save when done Select SSD VMEDIA v Network Authentication Open v WEP Encryption Disabled v Apply Save 2 Configure WPA Pre shared key as below and click Apply Save Select SSID VMEDIA v Network Authentication WPA WPA2 PSK al WPA WAPI passphrase Le Click here to displa WPA Group Rekey Interval 0 WPA WAPI Encryption TKIP AES WEP Encryption Apply Save 33 VDSL Router User Manual 3 Enable WPS as below WPS Setup Enable WPS Enabled v Add Client This feature is available only when WPA PSK WPS1 WPA2 PSK or OPEN mode is configured av Enter STA PIN Use AP PIN Add Enrollee Set WPS AP Mode Configured Y Setup AP Configure all security settings with an external registar Device PIN 176229909 Help 4 Set WPS AP mode as unconfigured and click Config AP WPS Setup Enable WPS Enabled Y Add Client This feature is availab
13. that your ISP has provided to you Click Next PPP Username PPP Password PPPoE Service Name Authentication Method AUTO y v Dial on demand with idle timeout timer PPP IP extension EJ Use Static IPv4 Address Enable PPP Debug Mode C Bridge PPPoE Frames Between WAN and Local Ports PPPoE service name can be blank unless your Internet Service Provider gives you a value to enter Authentication method is default to Auto It is recommended that you leave the Authentication method in Auto however you may select PAP or CHAP if necessary The default value for MTU Maximum Transmission Unit is 1500 for PPPoA and 1492 for PPPoE Do not change these values unless your ISP asks you to Enable Full Cone NAT In full cone NAT all requests from the same private IP address and port are mapped to the same public source IP address and port 24 VDSL Router User Manual Someone on the Internet only needs to know the mapping scheme in order to send packets to a device behind the VDSL Device The gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the Dial on demand check box and entering the Inactivity timeout The entered value must be between 1 minute and 4320 minutes Use Static IPv4 address If the ISP gave you a static fixed IP address select this option and enter it in the IP Address field If the ISP did not give you a static IP
14. the IP packets between WAN and LAN ports unless the packet is addressed to the gateway s LAN IP address 7 Select a preferred wan interface as the system default gateway Selected Default Available Routed WAN Gateway Interfaces Interfaces HN 8 Get DNS server information from the selected WAN interface or enter static DNS server IP addresses If only a single PVC with IPoA or static MER protocol is configured you must enter static DNS server IP addresses Select DNS Server Interface from available WAN interfaces Selected DNS Server Interfaces HON O Use the following Static DNS IP address Available WAN Interfaces Primary DNS server Secondary DNS server 9 Make sure that the settings below match the settings provided by your ISP Click on the Apply Save button to save your configurations 21 VDSL Router User Manual Connection Type FPPOE HAT Ena bled Full Cone NAT Disabled Firewall Enabled IGMP Multicast Disabled Quality Of Service Enabled 5 2 3 Router Mode Setup 1 From Advanced Setup click Layer2 Interface and select ETH Interface Before you configure ETH WAN interface you d better remove all PVC settings from ATM interface Interface Name Connection Mode Remove 2 Click Add and you ll see the following screen ETH WAN Configuration This screen allows you to configure a ETH port Select a ETH port eth0 ethd vw Apply Save
15. E service name can be blank unless your Internet Service Provider gives you a value to enter Authentication method is default to Auto lt is recommended that you leave the Authentication method in Auto however you may select PAP or CHAP if necessary The default value for MTU Maximum Transmission Unit is 1500 for PPPoA and 1492 for PPPoE Do not change these values unless your ISP asks you to Enable Full Cone NAT In full cone NAT all requests from the same private IP address and port are mapped to the same public source IP address and port Someone on the Internet only needs to know the mapping scheme in order to send packets to a device behind the VDSL Device 19 VDSL Router User Manual The gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the Dial on demand check box and entering the Inactivity timeout The entered value must be between 1 minute and 4320 minutes Use Static IPv4 address If the ISP gave you a static fixed IP address select this option and enter it in the IP Address field If the ISP did not give you a static IP address clear the Use Static IP Address option The ISP automatically assigns the WAN connection an IP address when it connects Enable PPP Debug Mode Select this to turn on the debug mode for the PPP connection Bridge PPPoE Frames Between WAN and Local Ports In addition to the VDSL Device s built in PPPoE client you can enable this to pass
16. acters in the user name and a maximum of 32 characters in the password 13 VDSL Router User Manual PPP Username PPP Password PPPoE Service Name Authentication Method AUTO Y Enable Fullcone NAT Dial on demand with idle timeout timer PPP IP extension Ise Static IPv4 Address E Enable PPP Debug Mode _ Bridge PPPoE Frames Between WAN and Local Ports PPPoE service name can be blank unless your Internet Service Provider gives you a value to enter Authentication method is default to Auto It is recommended that you leave the Authentication method in Auto however you may select PAP or CHAP if necessary The default value for MTU Maximum Transmission Unit is 1500 for PPPoA and 1492 for PPPoE Do not change these values unless your ISP asks you to Enable FullCone NAT all requests from the same private IP address and port are mapped to the same public source IP address and port Someone on the Internet only needs to know the mapping scheme in order to send packets to a device behind the ADSL router 14 VDSL Router User Manual The gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the Dial on demand check box and entering the Inactivity timeout The entered value must be between 1 minute and 4320 minutes The PPP IP Extension is a special feature deployed by some service providers Unless your service provider specifically requires thi
17. and an USB port in one unit bringing high speed wireless Internet connection to a home or office 1 1 Features 1 1 1 Data rate Downstream data rate up to 100 Mbps Upstream data rate up to 50Mbps 100 Mbps upstream with external AFE 1 1 2 DSL Compliant 1 13 Wireless ITU G 992 1 G DMT ITU G 993 2 G vdsl2 Profile 8a 8b 8c 8d 12a 12b and 1 7a 30a optional ITU G 992 2 G Lite ITU G 994 1 G hs ITU G 992 3 G DMT BIS ITU G 992 4 G lite bis ITU G 992 5 Compatible with all T1 413 issue 2 full rate DMT over analog POTS and CO DSLAM equipment Fully IEEE 802 11n compatible Wireless data rate up to 300Mbps Operating in the unlicensed 2 4 GHz ISM band Multi SSID Supports 64 128 bits WEP security and user authentication 1 1 4 Network Protocol amp Features Ethernet to ADSL Self Learning Transparent Bridging 2 VDSL Router 1 1 5 1 1 6 User Manual Internet Control Message Protocol ICMP IP Static Routing Routing Information Protocol RIP RIPv2 Network Address Translation NAT Virtual Server Port Forwarding Dynamic Host Configuration Protocol DHCP DNS Relay DDNS IGMP Proxy Simple Network Time Protocol SNTP VPN pass through IPSec PPTP L2TP Parent control ATM Capabilities VolP RFC 1483 Multi protocol over ATM Bridged Ethernet compliant RFC 2364 PPP over ATM compliant RFC 2516 PPP over Ethernet compliant ATM Forum UNI3 1 4 0 PVC Up to 16 PVCs
18. ber Forward unconditionally F EJ Forward on busy O Forward on no answer F F MWI O O Call barring z E Call barring pin 9999 Call barring digit map Warm line s Warm line number Anonymous call blocking Anonymous calling po O po o DND Call waiting If a calling party places a call to a called party which is otherwise engaged and the called party has the call waiting feature enabled the called party is able to suspend the current telephone call and switch to the new incoming call Typically this is done by pushing the flash button and can then negotiate with the 38 VDSL Router User Manual new or the current caller an appropriate time to ring back if the message is important or to quickly handle a separate incoming call Call Forwarding Number a feature that allows an incoming call to a called party which would be otherwise unavailable to be redirected to a mobile telephone or other telephone number where the desired called party is situated Forward the incoming call to the number you typed Select checkbox to enable the call forwarding function Enable MWI MWI means Message Waiting Indication Usually an audio or visual Signal that a voicemail or other type of message is waiting Call barring Telephone service feature that restricts certain types of outgoing calls such as international calls and or incoming calls such as from undesirable callers with the use of a code DND Selec
19. eless communication problems Field Band Channel 54g Rate Multicast rate Basic rate Fragmentatio n threshold RTS threshold DTIM interval Description This is the range of frequencies the gateway will use to communicate with user s wireless devices Drop down menu that allows selection of specific channel This drop down list lets user specify the wireless communication rate which can be Auto uses the highest rate when possible or else a lower rate or a fixed rate between 1 and 54 Mbps This drop down list lets user specify the wireless communication rate for multicast packets which are sent to more than one destination at a time The value can be Auto uses the highest rate when possible or else a lower rate or a fixed rate between 1 and 54 Mbps User has the option of supporting all rates listed in Rate above or using the 1 2 Mbps rates which support only older 802 11b implementations A threshold specified in bytes that determines whether packets will be fragmented and at what size On an 802 11 connection packets that are larger the fragmentation threshold are split into smaller units suitable for the circuit size Packets smaller than the specified fragmentation threshold value are not fragmented Enter a value between 256 and 2346 If user experience a high packet error rate try to increase this value slightly Setting the fragmentation threshold too low may result in poor performance This
20. ind of telephone otherwise DSL Router may occur frequently off line VDSL Router User Manual 2 Hardware Description Front Panel te cor Ae On Power on PWR Green Off No power On LAN link established and active via LAN port LAN1 2 3 4 Green Blinking DSL data activity occurs Off No LAN link via LAN port On The wireless module is ready and idle WLAN Green Blinking Data transmitting or receiving over WLAN Off The wireless is not installed On DSL link established and active DSL Green Quick blinking DSL is trying to establish a connection Slow blinking No DSL link On IP connected Blinking IP connected and IP traffic is passing through INET Green the device ES Off DSL connnection not present On A telephone connected to the phone port has its receiver off of the hook VOIP1 2 Green Off The handset of telephone connected to the phone port is on hook VDSL Router User Manual Rear panel Connect the device to an ADSL telephone jack or splitter DSL using a RJ 11 telephone cable FXSO 1 Connect the device to your normal phone LAN1 2 3 4 ON OFF POWER Side Panel WIFI The switch of wireless function RESET System reset or reset to factory defaults WPS A convenient way to set wireless security VDSL Router User Manual 3 Hardware Installation This chapter shows you how to connect Router Meanwhile it introduces the appropriate environment for the Router and installation instructions
21. le only when WPA PSK WPS1 WPA2 PSK or OPEN mode is configured Enter STA PIN Use AP PIN Add Enrollee Help Set Authorized Station MAC Help UnconfiguredikW Set WPS AP Mode Setup AP Configure all security settings with an external registar Device PIN 176229909 Help Config AP 5 Set WPS AP mode as configured and click Save Apply 6 Now you can use a wireless adaptor with WPS function and the WPS button to connect to access the Internet 7 To configure security features for the Wireless interface please open Security item from Wireless menu This web page offers nine authentication protocols for user to secure user s data while connecting to networks There are four selections including Open Shared 802 1X WPA WPA PSK WPA2 34 VDSL Router User Manual WPA2 PSK Mixed WPA WPA2 Mixed WPA WPA2 PSK Different item leads different web page settings Please read the following information carefully The wireless security page allows user to configure the security features of user s wireless network Select SSID VMEDIA w Network Authentication Open hol EP Encryption Enabled w Encryption Strength 1128 bit M Current Network Key w Network Key 1 1234567890123 Network Key 2 1234567800123 Network Key 3 1234567890123 Network Key 4 1234567890123 There are several security methods to choose from depending on user s needs and the capabilities of user s wireless
22. n is selected The gateway becomes the default gateway and DNS server to the computer through DHCP using the LAN interface IP address 25 VDSL Router User Manual The gateway extends the IP subnet at the remote service provider to the LAN computer That is the PC becomes a host belonging to the same IP subnet The DSL gateway bridges the IP packets between WAN and LAN ports unless the packet is addressed to the gateway s LAN IP address 9 Select WAN interface as the system default gateway Click Next Selected Default Available Routed WAN Gateway Interfaces Interfaces HN 10 Get DNS server information from the selected WAN interface or enter static DNS server IP addresses Click Next Select DNS Server Interface from available WAN interfaces Selected DNS Server pitais Go Available WAN Interfaces nterfaces HON O Use the following Static DNS IP address Primary DNS server J Secondary DNS server 26 VDSL Router User Manual 11 Make sure that the settings below match the settings provided by your ISP Click on the Apply Save button to save your configurations and reboot the DSL router Connection Type HAT Full Cone NAT Firewall IGMP Multicast PPPoE Enabled Disabled Enabled Disabled Quality Of Service Enabled 5 2 4 LAN Settings From LAN Configure the DSL Router s IP Address and Subnet Mask for LAN interface In this page you can use DHCP D
23. n make it blank if your ISP hasn t given you the address SIP Server Port is the signal port of SIP server The default value is 5060 SIP Outbound Proxy is SIP Outbound server The default value is 000 000 000 000 The parameter is useful only when the Outbound service is open 37 VDSL Router User Manual SIP Outbound proxy port is the signal port of outbound proxy port The default value is 5060 SIP Registrar The SIP server address provided by your ISP This address is necessary for VOIP setting SIP Registrar port the signal port of SIP server The default value is 5060 Extension SIP account username provided by your ISP The value is necessary for VOIP setting Display Name The line number assigned by your ISP Password SIP account password provided by your ISP The value is necessary for VOIP setting Input necessary value and then click Start SIP client 5 4 2 SIP Advanced Setting Please Click Stop SIP client before configure SIP parameter and click Start SIP Client after setting Global parameters Service Provider O Voice SIP Advanced configuration MOTE For CafCtri 1 10 x this page displays activation status for each feature PAA he r r e j le e rnane sn re a A bre E ap LE a png En a Errar Len pen For CCTK 2 x this page d spys enan status for eacn reature not n rate From Ke nad Activated SIP Call Features Feature Account O Account 1 Call waiting da E Call forwarding num
24. nd the wireless Router PC cannot access the Internet First check whether PC can ping the interface Ethernet IP address of this product successfully default value is 192 168 1 1 by using ping application If ping application fails please check the connection of Ethernet cable and check whether the states of LEDs are in gear If the PC uses private IP address that is set manually non registered legal IP address please check 1 Whether IP address of the PC gateway is legal IP address Otherwise please use the right gateway or set the PC to Obtain an IP address automatically 2 Please confirm the validity of DNS server appointed to the PC with DSL operator Otherwise please use the right DNS or set the PC to Obtain an IP address automatically 3 Please make sure you have set the NAT rules and convert private IP address to legal IP address IP address range of the PC that you specify should meet the setting range in NAT rules 4 Central Office equipment may have problem 42 VDSL Router User Manual 5 The country or the wireless network type you selected is wrong Q PC cannot browse Internet web page A Please make sure DNS server appointed to the PC is correct You can use ping application program to test whether the PC can connect to the DNS server of the DSL operator Q Initialization of the PVC connection failed A Be sure that cable is connected properly from the DSL port to the wall jack The DSL LED on the
25. nterface DSL Latency PTM Priority Conn Mode IP QoS Remove 2 Click Add to configure PTM Priority select DSL latency and select connection mode according to your local occasion After the configuration you need to click Apply Save Select DSL Latency PathO Fast L Pathi Interleaved Select Scheduler for Queues of Equal Precedence as the Default Queue Weighted Round Robin Weighted Fair Queuing 3 Click WAN Service from the left menu Interface Description Type Vlan8021p VlanMuxid Igmp NAT Firewall Remove Edit 4 Click Add to select a layer 2 interface for this service and then click Next 17 VDSL Router User Manual 5 Choose WAN service type just choose PPPoE for example here You can enter your own service description here if you want and then click Next Select WAN service type PPP over Ethernet PPPoE IP over Ethernet Bridging Enter Service Description pppoe_0_ 0 1 6 Input PPP Username 8 PPP Password and then click Next The user interface allows a maximum of 256 characters in the user name and a maximum of 32 characters in the password 18 VDSL Router User Manual PPP Username PPP Password PPPoE Service Name Authentication Method AUTO v Enable Fullcone NAT Dial on demand with idle timeout timer PPP IP extension b Use Static IPv4 Address Enable PPP Debug Mode Bridge PPPoE Frames Between WAN and Local Ports PPPO
26. og box click the IP Address tab Set the IP address as 192 168 31 x x can be a decimal number from 2 to 254 like 192 168 31 2 and the subnet mask as 255 255 255 0 5 On the Gateway tab set a new gateway as 192 168 31 1 and then click Add 6 Configure the DNS tab if necessary For information on the IP address of the DNS server please consult with your ISP 7 Click OK twice to confirm and save your changes 8 You will be prompted to restart Windows Click Yes Local PC Configuration in Windows 2000 1 Inthe Windows task bar click the Start button point to Settings and then click Control Panel 2 Double click the Network and Dial up Connections icon 3 Inthe Network and Dial up Connections window right click the Local Area Connection icon and then select Properties 4 Highlight Internet Protocol TCP IP and then click Properties 5 Inthe Internet Protocol TCP IP Properties dialog box set the IP address as 192 168 31 x x can be a decimal number from 2 to 254 and the subnet mask as 255 255 255 0 and the default gateway as 192 168 31 1 Then click OK 6 Configure the DNS tab if necessary For information on the IP address of the DNS server please consult with your ISP 7 Click OK twice to confirm and save your changes 10 VDSL Router User Manual 5 Web based Management Guide In order
27. s setup do not select it If you need to select it the PPP IP Extension supports the following conditions t allows only one computer on the LAN The public IP address assigned by the remote using the PPP IPCP protocol is actually not used on the WAN PPP interface Instead it is forwarded to the computer s LAN interface through DHCP Only one system on the LAN can be connected to the remote since the DHCP server within the ADSL gateway has only a single IP address to assign to a LAN device NAPT and firewall are disabled when this option is selected The gateway becomes the default gateway and DNS server to the computer through DHCP using the LAN interface IP address The gateway extends the IP subnet at the remote service provider to the LAN computer That is the PC becomes a host belonging to the same IP subnet The ADSL gateway bridges the IP packets between WAN and LAN ports unless the packet is addressed to the gateway s LAN IP address Use static IPv4 IP address If the ISP gave you a static IP address select this option and enter it in the IP address field Bridge PPPoE Frames Between WAN and Local Ports is available when you do not use PPP IP extension If you enable this function LAN hosts can use PPPoE client software on their computers to connect to the ISP Each host can have a separate account and a public WAN IP address 7 Default gateway interface list can have multiple WAN interfaces served as sy
28. stem default gateways but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN 15 User Manual VDSL Router interface is connected Priority order can be changed by removing all and adding them back in again Available Routed WAN Selected Default Gateway Interfaces Interfaces NN 8 Get DNS server information from the selected WAN interface or enter static DNS server IP addresses If only a single PVC with IPoA or static MER protocol is configured you must enter static DNS server IP addresses Select DNS Server Interface from available WAN interfaces Selected DNS Server Available WAN Interfaces Interfaces pppd 1 O Use the following Static DNS IP address Primary DNS server Secondary DNS server 9 Make sure that the settings below match the settings provided by your ISP Click on the Apply Save button to save your configurations Now reboot the ADSL Gateway 16 VDSL Router User Manual Connection Type FPPOE HAT Enabled Full Cone HAT Disabled Firewall Enabled il IGMP Multicast Disabled Quality Of Service Enabled 5 2 2 VDSL Setup From home page you can find Advanced Setup option on the left router configuration page 1 From Layer2 Interface click PTM Interface you can set it up according to the following steps You Choose Add or Remove to configure DSL PTM interfaces I
29. t the checkbox to enable DND support The Do Not Disturb or DND function prevents calls from ringing on an extension for which DND is activated Some Do Not Disturb DND attributes include directing the call to a pre assigned extension like a secretary or assistant busy signal DND signal or recorded message generated by the telephone switch 5 5 Printer Server Installations 1 Click Advanced setup Print Server and then Check Enable on board printer server and key in Printer name Make and model Print Server settings This page allows you to enable disable printer support Enable on board print server Sawe Apply 2 Click on Add a printer from Control Panel of the Windows computer and click Next 39 VDSL Router User Manual Add Printer Wizard Welcome to the Add Printer Wizard This wizard helps you install a printer or make printer connections To continue click Next lt Back Cancel 3 Select Network Printer and click Next Add Printer Wizard y Local or Network Printer Is the printer attached to your computer If the printer is directly attached to your computer click Local printer If it is attached to another computer or directly to the network click Network printer Local printer IV Automatically detect and install my Plug and Play printer Network printer lt Back Cancel 4 Select Connect to a printer on the Internet t
30. the following steps You Choose Add or Remove to configure DSL ATM interfaces A z DSL Peak Cell Rate Sustainable Cell Rate Max Burst Size Link Interface Vpi Vci Category Conn IP MPAAL Laten cells s cells s bytes cy Type Mode Qos Prec Alg Wght Remove 2 Click Add to configure PVC identifier select DSL latency and select connection mode according to your local occasion After the configuration you need to click Apply Save ee el UN elect DSL Latency PathO Fast C Pathi Interleaved Select DSL Link Type EoA is for PPPoE IPoE and Bridge EoA PPPoA IPoA Encapsulation Mode LLC SNAP BRIDGING v Service Category UBR Without PCR v Select Scheduler for Queues of Equal Precedence as the Default Queue Weighted Round Robin Weighted Fair Queuing 3 Click WAN Service from the left menu 12 VDSL Router User Manual Interface Description Type Ylan8021p YlanMuxid Igmp NAT Firewall Remove Edit 4 Click Add to select a layer 2 Interface for this service and then click Next atmo 0_0_35 5 Choose WAN service type just choose PPPoE for example here You can enter your own service description here if you want and then click Next Select WAN service type PPP over Ethernet PPPOE IP over Ethernet Bridging in Cription pppoe _O 035 6 Input PPP Username 8 PPP Password and then click Next The user interface allows a maximum of 256 char
31. tion each other I Enter a name for user s wireless network here SSID stands for Service Set Network Identifier This name must be between 1 and 32 characters long All wireless name SSID clients must either detect the gateway or be configured with the correct SSID to access the Internet BSSID Displays the gateway s wireless MAC address User may need this address if user s using WDS or multiple gateways Click Apply to save changes Country Drop down menu that allows selection of specific channel o 5 3 2 Advanced Band 2 4GHz w Channel Auto w Current 8 interference acceptable Auto Channel Timer min 802 11n EWC Auto e Bandwidth 40MHz in Both Bands v Current 40MHz Control Sideband Current Upper 802 11n Rate 802 11n Protection Support 802 11n Client Only RIFS Advertisement DTIM Interval Beacon Interval 100 on Global Max Clients OBSS Co Existance RX Chain Power Save Power Save status Rx Chain Power Save Quiet ho Time RX Chain Power Save FPS 349 3M Rate Multicast Rate Fragmentation Threshold RTS Threshold XPressMi Technology Disabled Transmit Power WMM Wi Fi Multimedia Enabled WMM No Acknowledgement Disabled WMM APSD Enabled Note After making any changes click Apply to save 30 VDSL Router User Manual Warning The settings shown above are default settings Changes made to these items can cause wir
32. to use the web based management software it will be necessary to use a computer that occupies the same subnet as the Router The simplest way to do this for many users will be to use DHCP server that is enabled by default on the Router 5 1 LAN setting page Launch a web browser such as Internet Explorer and then use http 192 168 31 1 to log on to setting page Connect to 192 166 1 1 EPA Enter username admin and password admin 4 Remember my password ae cu i After log on you will see the following screen Please select Wizard or Advanced mode The Wizard setup walks you through the most common configuration settings We suggest you use this mode if it is the first time you are setting up your router or if you need to make basic configuration changes Use Advanced mode if you need access to more advanced features not included in Wizard mode Go to Wizard setup Go to Advanced setup Click here to always start with the Advanced setup 11 VDSL Router User Manual We can select wizard setup or advanced setup mode to setup KW5262 the wizard set up will guide us for a basic setting and the advanced setup will guide us to home page for more detailed setup 5 2 Internet Access Configuration 5 2 1 ADSL Setup From home page you can find Advanced Setup option on the left router configuration page 1 From Layer2 Interface click ATM Interface you can set it up according to
33. uina nu AA aan 5 14 FACTORY DEFAULTS circa 5 15 NVARNINGS AND CAUTIONS naa aeecaweccsaaocuauseareeaimeanseeaie 5 2 HARDWARE DESCRIPTION casi i 7 3 HARDWARE INSTALLATION iisssccesccssscrscsescccstisaccascsenceecsseaetseccnscseivaesaateccvastaies eapatecsoestaseaunseseess 9 4 PC CONFIGURATION GUIDE atraido 10 4 1 LOCAL PC CONFIGURATION IN WINDOWS 95 98 ME XP VISTA 7 un 10 4 2 LOCAL PC CONFIGURATION IN WINDOWS 2000 oooononcccooccconoccconcnnnoncnnncnnnonennanancnrenaaaannens 10 5 WEB BASED MANAGEMENT GUIDE cssscsccccccessssscceccccesessssscececcceeesssssceeeeceeeesssaees 11 5 1 LEAN SETMING PAGE in 11 5 2 INTERNET ACCESS CONFIGURATION 02 s sceeeeccccssseseeeeeeeeeccssseeeeeeeeeeeeessseeeeeseneoessseeeeees 12 D ADO SO 10 o S Mn A lt 12 ee VOSES UD iii 17 5 2 3 Router MODE AU e da 22 DA AIN SC UNOS SES a 27 5 3 WIRELESS SETTING isaac eee cn nn 29 D Bd l Pa l A se ne rs 29 de POV AI COO aera RE dde Lea Et E co DT ce E 30 o a tete ten i etes ie en ne ere 33 5 4 VOIP CONFIGURATION coi 37 S4 TSIP BASIC SOIN Eau eut ne 37 D 42017 AOVANCCO SENIOR Re ta 38 5 5 PRINTER SERVER INSTALLATIONS cidad 39 APPENDIX FREQUENT ASKED QUESTIONS o cccccnnncononnncccccnnccononanccccconocononanccccnonocononnnos 42 VDSL Router 1 Overview User Manual Thank you for choosing our product The KW5262 is a Wireless VDSL router combining an DSL modem an 802 1 1n wireless router a 4 port switch two FXS ports
34. ur device in dotted decimal notation for example 10 0 0 1 Type the subnet mask Note If you want to cancel all modification that you do on the Router please select from Management gt Setting gt Restore Default Settings to restore factory default settings 28 VDSL Router 5 3 Wireless setting 5 3 1 Basic Wireless Guest Virtual Access Points Enabled SSID Ly a Option Enable wireless Hide Access Point Clients User Manual lun f Ny Disable 3 Isolate E Enable Max Hidden _ WMM BSSID Chents WMF Cents Advertise ll a L a uest2 mn jo 0 O o lo e O lis in Description A checkbox that enables or disables the wireless LAN interfaces The default is to enable wireless communications Select Hide Access Point to protect the ADSL route access point from detection by wireless active scans If you do not want the access point to be automatically detected by a wireless station this checkbox should be deselected The station will not discover this access point To connect a station to the access point the station must manually add this access point name in it s wireless configuration In Windows XP go to the Network gt Properties function to view all of the available access points You can also use other software programs such as NetStumbler to view available access points Enable this item if you don t want your wireless clients to communicate with 29 VDSL Router User Manual isola
35. user s wireless devices might not be able to use it WPA2 PSK this option uses WPA2 with a pre shared key WPA2 and WPA This option supports WPA2 WPA encryption for devices capable of one or the other standard The gateway automatically detects whether a particular device can use WPA2 or WPA WPA2 AND WPA PSK this has WPA2 or WPA encryption based on client abilities as well as a pre shared key After making changes click Apply to save 36 VDSL Router User Manual 5 4 VolP Configuration 5 4 1 SIP Basic Setting Please Click Stop SIP client before configure SIP parameter and click Start SIP Client after the setting Global parameters Service Provider 0 Voice SIP configuration Enter the SIP parameters and cick Start Stop to save the parameters and start stop the voice DARTE E 7 Note Requires the SIP client LOC S cnon USA NORTHAMERICA v affect SIP domain name Voy Diaipan Setting Le Use SIP Pro SIP Proxy SIP Proxy port cnc Use SIP Outbound Proxy SIP Outbound Pra SIP Outbound Proxy port 50 Le Use SIP Registrar SIP Registrar SIP Regstrar port 506 SIP Account T 1 Account Enabled C al Extension Display name Authentication name Password Interface Name PVC channel for VoIP service Locale Selection Keep the value as default if without any request from your ISP Preferred codec list Voice codecs SIP Proxy SIP proxy server address or domain name of SIP service You ca
36. uter Please make sure what you use is the power adaptor attached with the DSL router package and checks the connection between the AC power and DSL router DSL LED does not turn on after connect telephone line Please make sure what you use is the standard telephone line as attached with the package make sure the line is connected correctly and check whether there is poor contact at each interface Wait for 30 seconds to allow the DSL router establishes connection with you DSL operator DSL LED is in the circulation of slow flashing and fast flashing after connecting telephone line A RO RO 2O This situation means the DSL router is in the status of failing to establish connection with Central Office Please check carefully and confirm whether the DSL router has been installed correctly LAN LED does not turn on after connect Ethernet cable Please make sure Ethernet cable is connected hub PC and DSL router correctly Then please make sure the PC hub have been power on Please make sure that you use parallel network cable to connect UpLink port of hub or use parallel network cable to connect PC If connect normal port of hub not UpLink port you must use cross cable Please make sure that your network cables meet the networking requirements above PC cannot access the Router Please make sure that all devices communicating with the device must use the same channel and use the same SSID Otherwise your PC will not fi
37. ynamic Host Configuration Protocol to control the assignment of IP addresses on your local network Local Area Network LAN Setup MAC Address IP Address Remove ltem Description 27 me Default Y VDSL Router IP address Subnet mask Disable Enable DHCP server Start end IP address Lease time Enable DHCP server relay Configure the second IP address and User Manual This is the IP address that other devices on your local network will use to connect to the modem This defines the size of your network The default is 255 255 255 0 The DHCP server assigns an IP addresses from a pre set pool of addresses upon request from DHCP client e g your computer Do not disable the DHCP server unless you wish to let another device handle IP address issuance on the local network This is the beginning and ending range for the DHCP server addresses The amount of time before the IP address is refreshed by the DHCP server If NAT is disabled and the PVC is the IPoA or static MER type this item allows you to inform the router of another DHCP server on your LAN To do this disable the DHCP server on the gateway Then input the IP address of the current DHCP server Click Apply and restart the gateway Select this option to let the device use a second IP address on the LAN interface You can also use this second IP address to access the device for management Enter the LAN IP address of yo
38. ype http 192 168 1 31 631 printers printer and click Next The printer name Printer must be the same name entered in the ADSL router print server setting as in step 1 Locate ous Prime Hor da pas eed bo sie our pores Ifyou dont know de name of the ponber pou can boiata hor one on the meshed hal de vou wan bo do E Types the printer name of click Hed bo browse lor a painter Name fo Connect lo s porter on the inteme or on pour mirana 1192 168 31 1 prnters printer as CE es 40 VDSL Router User Manual 5 Select driver file directory on CD ROM or in your hard disk and click OK 6 Choose Yes or No for default printer setting and click Next Add Printer Wizard 7 Default Printer Your computer will always send documents to the default printer unless you specify otherwise Do you want your Windows based programs to use this printer as the default printer Yes C No lt Back Cancel 7 Click Finish Add Printer Wizard Completing the Add Printer Wizard You have successfully completed the Add Printer wizard You specified the following printer settings Name Printer on 192 168 1 1 Default Yes Location Comment To close this wizard click Finish lt Back Cance 41 VDSL Router User Manual Appendix Frequent Asked Questions Q A RO Q None of the LEDs are on when you power on the DSL ro
Download Pdf Manuals
Related Search