INSTALLATION MANUAL: CDI OPTIONS
Contents
1. Horse INSTALLATION MANUAL CDI OPTIONS QUICK SHIFT SYSTEM TPS Power Jet l iti HPI Kuilenstraat 97 3960 Bree Belgium gni ion TEL 0032 089 46 74 39 FAX 0032 089 47 33 28 GSM 0032 0495 53 90 21 Email hpi hpi be Website www hpi be Quick shift shift delay The HPI Shift Delay Function enables you to shift gears without clutching or throttling down The flexibility of the system allows you to fully adapt it to your needs The SD system can be programmed to work with every type of switch The active period is settable from 0 to 1000 ms The SD system can cut the ignition or delay the ignition by 60 during the active period Included counter plug to wire up your switch The table below shows all possible setups Determine which switch type you are using nomally open or nomally closed Usually a button or switch with a short leaver is used so that the button immediately picks up the movement of the gearing pedal The longer the leaver the longer it takes before the button will react The used button should not be sensitive to vibrations these may cause to start the Shift Delay to start unwanted Normally j open switch O MAKE Normal driving Hitting the button Releasing the button Bantact Contact is open Contact closes MAKE Contact opens Shift Delay period SD period continues reaction starts Normally closed switch Normal dnving Hitting the button Releasing the button B2. I Kuilenstraat 97 3960 Bree Belgium gni ion TEL 0032 089 46 74 39 FAX 0032 089 47 33 28 GSM 0032 0495 53 90 21 Email hpi hpi be Website www hpi be TPS The HPI Throttle Position Sensor system allows you to fine tune your engine even further The HPI CDI can take 5 curves automatically selected by the TPS position If your bike is already equipped with a TPS the HPI CDI equipped with this feature will use the same connectors or pins as the OEM CDI So you don t have to worry about rewiring your bike If the OEM bike does not have a TPS HPI will equip the CDI with a 3 pole connector and counter part this Te connector is widely used as connector for TPS 1 i TPS signal a 3 AHPI CDI with TPS always comes with a handle bar button Switch the button to turn the TPS function on and off while driving When the handle bar switch selects MAP 1 the CDI will always select the curve 1 black curve in TuneBox Use this curve for sound emission or rpm controls When the handle bar switch selects MAP 2 the CDI will select curve 2 3 4 5 6 according to the TPS position If you don t have a TPS on your bike disable the TPS system in TuneBox by selecting 1 or 2 curves TuneBox 5 Curve Control File Eeim Active Visible Copy Reset Revy Limiter Ports d LO E y Ei Ej Display ZRUG CDI options 3 E al l 4 E py l m Language at Surber of curves 1 5 il Ei E Power Jet 2 r Set as stan
3. dard options yig i L v ml m Shift Delay H 6 Adjust Active Curve _ Power Jet The HPI Power Jet function allows you to drive a Power Jet exhaust valve air box light related to the engine s rpm If your bike is equipped with a Power Jet the HPI CDI will use the same connectors or pins as the OEM CDI So you don t have to worry about rewiring your bike Power Jet Control wl Fo A HPI CDI can carry 2 Power Jet exits both independently settable with TuneBox tissa Lesen Each Power Jet exit can be activated twice over the RPM range 2500 4 0H F500 7500 n is only 1 set of PJ settings the PJ will be activated at the same rpm Bevel pes in all curves oli I In the defined rpm range the power jet exit will be driven to GND with a 0000 TH maximum load of 1 7 Amps
4. reak Contact is closed Contact opens BREAK Contact closes contact Shift Delay period SD period continues reaction starts Use the TuneBox software to change the settings of the SD system Choose the make or break contact reaction in the dropdown menu Here you can also choose to delay or to cut the ignition TuneBox v5 TuneBox 5 File gemme File Eene Forts Forts F Display j Display d COI options CDI options Language Number of curves Language b Number of curves Power Jet l m T Power Jet Sore mela et as standard options a shift Delay __ off Shift Delay off Make Contact Set as standard options w Make Contact Break Contact w Break Contact spark d Ry yw no spark retarded In TuneBox you can also determine the length of the period that the Shift Delay effect will take place Shitt Delay 743 Use the arrow to set the period of the Shift Delay us You can enter any value between 0 and 1000 ms break no spark In most cases a value about 200 ms is sufficient If you don t have a shift sensor or if you don t want to use the shift system you should turn off the Shift delay system in TuneBox This will prevent the system to start the Shift Delay unwanted Go to the TuneBox Options menu gt CDI options gt Shift Delay gt and select off or you can seta period of 0 ms Horse INSTALLATION MANUAL CDI OPTIONS QUICK SHIFT SYSTEM TPS Power Jet l iti HP
Download Pdf Manuals
Related Search