Owners Manual
Contents
1. 8 1 Analog connector 8 interlock connector ae i Ega Manufacturer Molex 90130 3206 mates with 90143 0006 Pin Function 1 Interlock connect to pin 2 for enable 2 GND 3 Analog on off Direct input Pin 2 Pin 4 Pin 6 4 TST Internal Cobolt use only 5 LED Laser on 5V 6 LED Error 5V Warning shortening pin 2 and 4 when the controller is powered up will erase the controller memory 8 2 Power connector Kycon KPJX 4S mates with Kycon KPPX 4P Grounded shield Pin 1 Pin 2 Pin Function 1 OV 2 11 28 VDC 3 OV 4 411 28 VDC PEFS Pin 4 8 3 Data connector Connector USB type manufacturer Hsuan Mao C8320 O5BFDSBO mates with connector mini B Pin Function 1 5 V in series with internal 10 Ohm resistor 2 RS 232 TX 3 RS 232 RX 4 Not connected 5 OV GND 14 Cobolt Zouk Calypso Samba M Jive Flamenco Rumba 9 Operation via data port 9 1 Baud rates and serial port settings To communicate with the laser a communication cable needs to be ordered separately Each Controller is shipped from the factory with a fixed baud rate 115200 which cannot be changed in the field The other serial port parameters are 8 data bits 1 stop bit and no parity Hardware flow control is not supported Each command to the Controller must be terminated by a carriage return All commands are case sensitive Leading and trailing white space is ignored but command arguments must be del2. 48 22 207 22 78 Fax 48 22 207 22 77 www amecam pl South Korea SM Tech Phone 82 42 8244413 Fax 82 42 8244414 WWW lasersystem co kr UK amp Ireland Laser Lines Ltd Phone 44 1295 672 500 Fax 44 1295 672 550 www laserlines co uk Laser 2000 Benelux CV Phone 31 297 266 191 Fax 31 297 266 134 www laser2000 nl China DynaSense Photonics Co Ltd Phone 86 0 10 83503853 Fax 86 0 10 83503622 www dyna sense com France Optoprim Phone 33 1 4190 6180 Fax 33 1 4190 6189 www optoprim com India Dynotech Instruments Pvt Ltd Phone 91 124 4086513 16 Fax 91 124 2331653 www dynotech in Japan Kantum Electronics Co Ltd Phone 81 3 37581113 Fax 81 3 37588066 www kantum co jp Russia Belarus Azimuth Photonics Phone 7 495 792 39 88 Fax 7 495 958 23 09 www azimp ru Spain 8 Portugal Laser Technology SI Phone 34 93 750 0121 Fax 34 93 750 0323 www laser technology com USA Cobolt Inc Phone 1 408 708 4351 Fax 1 408 490 2774 www coboltinc com Photonics Instrumentos Phone 55 11 2910 6852 Fax 55 11 2910 6852 www photonics com br China New Opto Technology Corporation Telephone 86 571 8515 2711 Fax 86 571 8515 2727 www newopto com Germany Austria Switzerland Von Gegerfelt Photonics Phone 49 6251 860 99 20 Fax 49 6251 860 99 17 www vgphotonics eu Israel Lahat Technologies Ltd Phone 972 4 999 0151 Fax 972
3. 1 e2 at aperture Calypso 491 5 0 3 nm 200 mW lt 1 2 mrad 700 50 um samba 532 1 030m O5 10or15W 700 50 ym ive 561 20 31m 200 300 or 500 mu 700 50 ym Flamenco 659 6 0 3 nm 100 300 or 500 mW lt 1 5 mrad 700 50 um Rumba 10642 06nm 05 10 20o30W L6mad 1000 SOpm Mv ZoukTM Calypso Samba Jive Flamenco Rumba Noise 20 Hz 20 MHz peakpeak ax Noise 20 Hz 20 MHz rms Long term power stability 8 hours 296 3 C Spatial mode TEMoo M 1 1 1 The wavelength is fixed with this accuracy while drift is 0 02nm The wavelength is specified in air 2 The output power can be adjusted using control commands see Section 9 Specifications are guaranteed at 100 of nominal power Recommended power range is 50 100 Nominal power accuracy 5 10 Cobolt Zouk Calypso Samba M Jive Flamenco Rumba 6 2 Operational and environmental requirements Power supply 15 VDC 4 2 A 11 28 VDC accepted Power consumption total system Laser Head Controller lt 63 W typical 30 W Maximum heat dissipation of Laser Head lt 50 W typical 20 W Maximum Laser Head baseplate temperature 50 C Warm up time from OFF Ambient temperature operation 10 40 C Ambient temperature storage 0 60 C 0 60 RH non condensing Ambient Air pressure 950 1050 mbar Heat sink thermal resistance Laser Head lt 0 2 K W 6 3 Electrical interfaces Remote inter
4. appropriate Power Supply Unit PSU is supplied by Cobolt with the laser for low volume orders and is plugged into a standard power outlet The output from the Cobolt supplied PSU is 15 VDC and the current is 4 2 A max 63 W The power supply accepts 90 264 VAC and 47 63 Hz Ripple and noise 1 peak peak max 20 MHz bandwidth Accepted voltage range for the Controller is 11 V 28 VDC Specification values are given at 15 VDC 4 5 Identification labels The Laser Head and Controller are provided with a manufacturer s identification label including a serial number which is unique for each laser system and a certification label Cobolt Rumba 2000 Cobolt Rumba 2000 1064 nm 1064 nm 1064 05 01 2000 300 1064 05 01 2000 400 S N 1234 S N 1234 Made in Sweden C Made in Sweden OEM LASER Input VDC 15 V Iu 2 4 2 A Input VDC 15 V Ing 4 2 A DEVICE Cobolt AB Vretenvagen 13 Cobolt AB Vretenvagen 13 SE 171 54 Solna Sweden SE 171 54 Solna Sweden Manufacturer s identification labels CDRH L or OEM R Model number description Wavelength 500 CDRH controller RS 232 600 OEM controller RS 232 700 CDRH controller USB 800 OEM controller USB xxx OEM customisation Placement of labels Hazard Symbol and Aperture Label Manufacturers Certification label 8 Cobolt Zouk Calypso Samba M Jive Flamenco Rumba 5 Operation instructions As standard all lasers are delivered with the Contro
5. to turn the laser on Connecting 15 VDC power supply to the Controller initiates an automatic start up sequence See Section 5 1 for more information The laser will be running according to specifications in lt 3 min The operation of the laser can be controlled and monitored via the Data port supports control commands and analog signals See Section 9 for further details When power is supplied to the Controller regardless of on off state the temperature control elements are operating to reach setpoint values The Controller includes a remote interlock connector 2 pins on the left hand side within the 6 pin analog connector The connector can be short circuited with an interlock jumper included at delivery for operation of the laser To make use of the remote interlock as a safety switch remove the jumper and connect to an external switch NOTE when the interlock circuit has been opened during operation the laser needs to be disconnected from and then reconnected to the power supply in order to start again Alternatively it can be re started using a special sequence of control commands see Section 9 for further details 7 Cobolt Zouk Calypso Samba Jive Flamenco Rumba 4 3 Cable The Cable connects the Laser Head to the Controller The standard Cable length is 1 m and minimum bending radius 8 cm When connected care should be taken not to bend or break any of the 26 pins 4 4 Power supply requirements An
6. 9 76 46 204 www lahat co il Japan Pneum Co Ltd Japan Phone 81 48 985 2720 Fax 81 48 985 27 21 www pneum co jp Singapore Malaysia Thailand Photonitech Asia Pte Ltd Phone 65 6749 9031 Fax 65 6233 9171 www photonitech com Taiwan Tayhwa Technology Co Ltd Phone 886 2 23569737 Fax 886 2 23569659 www tayhwa com tw
7. a Gen5 SHG D501 4W RevB bd COM20 115200 Serial No 561006870 Fw Ver 5 526 A 5 1 The TEC Settings section displays the internal temperature control of the Laser Head and the fault status for the laser s internal thermoelectric coolers TEC Depending on model the laser has two to four TEC active 18 Cobolt Zouk Calypso Samba M Jive Flamenco Rumba 2 The Laser Diode Settings section displays the set laser power The user can switch between constant power mode and constant current mode Likewise there are boxes to set the constant power level and constant current level The output power as monitored measured on an internal photodiode and the current through the laser pump diode are both displayed 3 The Autostart section displays whether the laser is in LAB or OEM mode and displays the current laser operational status 5V direct input is set here see Section 9 4 There are also buttons to abort the autostart sequence or restart the laser after a fault 4 Under General there is a Clear Fault button This can be used to restart the laser after the interlock has been removed and re inserted 5 The LEDs section displays the LEDs that are currently illuminated on the Control Box see Section 4 2 These are displayed even if the laser is in OEM mode 12 Troubleshooting In the unlikely case of a problem occurring use the table below to help identify the error Some faults can be fixed remotely Ca
8. e CO bolt Owners Manual Model 05 01 March 2014 rev 1 20 Cobolt Zouk CW 355 nm DPSSL Cobolt Calypso Cobolt Samba CW 491nm DPSSL CW 532nm DPSSL Cobolt Jive Cobolt Flamenco CW 561nm DPSSL CW 660nm DPSSL Cobolt Rumba CW 1064 nm DPSSL Cobolt AB Phone 46 8 54591230 infoOcobolt se Vretenv gen 13 Fax 46 8 54591231 www cobolt se SE 171 54 Solna Sweden Gru ic DE 3 Safety and precaution Instr ctlollS dcs osse cres oco a hh A 3 2 1 VAG labels dae 4 aser desig Arta ILL NI T T PU P 5 kaser system descrptlob seen near cnt a ed us odes ed ci e eu eM MM DIAM LE HM EM D M EM LAT M LE LEQUE 5 4 1 A PET 5 4 2 Controle MM M 6 4 3 Gcr e PEE 7 4 4 Power supply TEGU TEMEMES a c cuc avatakse a ida 7 4 5 Identificacion icio eee oa 7 Operaci n INTIS dai e dla dme TT OO AS A ASADA 8 5 1 Installation Startup ODE AON MEREMEES A ite vt lett uw Ee een ed bces inet Meese ald eee 8 5 2 Closedown operationis essen O A E A AA A A d eMe tad 8 SPECI ANON sic ii o ol co ol IN i M IE 9 6 1 Eai a E EA a II O O mi da 9 6 2 Operational and environmental requirements coccococcononconononnonenconencononnononcnnonennonennnnenronennnnenranenrnnonennnns 10 6 3 Electrical INtertaces o DC 10 6 4 Mechanical oras det ctas econo 10 VMechanicalQUtINe Sita bad e 11 Conn
9. ector drawings amp pin assignMent ida A eet EA A naad ee eee 13 8 1 Analog connector 8 interlock connector nrrnnnunnnnnennnnn nun nennen nan nne nenne ne nest sisse aes reser en rus 13 8 2 POWeF CONMEOCIO sua a Rr 13 8 3 Data CONNECTOR cenaa ao 13 OPERACION a a aia 14 9 1 Baud rates a a serial Dort settings ii A A aladel 14 9 2 a E ALO S Maclin 0 CCOO CC PEE EE DESTITIT 14 9 3 Cohtrolxcomimalids iii kkk 14 9 4 Bad 01 48 507010 0 OA I EN 15 o a ahi ai ahi CL M I DIM ADM aataid aadi aia 16 N 80181 911154 270161 41410 EA EU deleite dido Ui de dianas 16 Warranty and maintenance 0 0nnnnennnnnnennnnennane nn erre essa ess sess sese sese sanas 18 Declaration of conformity CDRH model only ios ies eva copa veas eus Sess ada 19 Bird YIN TS kS RET od 19 S ORV ICG rai C UI E 19 3 Cobolt Zouk Calypso Samba M Jive Flamenco Rumba 1 General Cobolt lasers are all continuous wave diode pumped solid state DPSS laser devices operating at fixed wavelengths as defined in the specifications in Section 6 The lasers have a compact hermetically sealed package and emit a high quality beam with stable characteristics over a wide range of operating conditions The lasers are designed and manufactured to ensure a high level of reliability The Cobolt lasers are intended for stand alone use in laboratory environment or for integration into instrumentation equipment us
10. ed e g in flow cytometry fluorescence microscopy particle amp flow analysis DNA sequencing interferometry Raman spectroscopy optical tweezers and laser pumping 2 Safety and precaution instructions Eye and skin exposure to direct or reflected laser light is hazardous and may be extremely harmful Always wear eye protection appropriate to the beam wavelength and intensity The device must be handled by personnel with experience in laser operation in a laboratory environment and with access to adequate laser safety equipment cobott Zouk ssm toamazo m amars p Asc ME AAA OR Cobolt Jive 561 nm Cobolt Flamenco 660 nm 100 and 300 EET Cobolt Rumba 1064 nm 500 1000 2000 3000 ME O The table below described the maximum irradiance in W cm and appropriate level of eye protection in terms of optical density OD for each product line Output Power mW Max Irradiance W cm Eye protection Requirement PA T Coboltwers tmm s00 04 0 CoboltFlamenco 660 mm soo 160 o sova 4 Cobolt Zouk Calypso Samba M Jive Flamenco Rumba Always install the laser system to a properly grounded power outlet Cobolt lasers contain a laser diode which is sensitive to electrostatic discharge ESD CAUTION use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure 2 1 Warning labels The Las
11. er Head clearly displays a warning label that shows the location of the laser beam from the aperture and an explanatory label stating the laser safety class compliance of the product These labels must be visible unless the laser beam is totally enclosed Visible Class 4 lasers IR Class 4 lasers UV Class 3b lasers Visible Class 3b lasers Examples Hazard Symbol and Aperture Label 5 Cobolt Zouk Calypso Samba M Jive Flamenco Rumba 3 Laser design The radiation from Cobolt lasers is generated by intra cavity frequency conversion in periodically poled material The laser beam is expanded in a telescope and emitted through a manual shutter The residual IR radiation from the pump and the DPSS laser is contained within the laser housing by filtering optics The laser assembly is equipped with elements for temperature control of the cavity and pump diode The laser is also featured with an optical feed back loop which ensures long term power stability of the emitted visual beam Control signals and drive currents are supplied via an electrical interface 4 Laser system description The Cobolt 05 01 laser system consists of four main parts Laser Head Controller Cable and Power supply The Cobolt Cable should always be used to connect the Laser Head with the Controller Cobolt Laser Head Controller and Cable 4 1 Laser Head The Laser Head contains pump diode laser cavity beam formatting optics and Pelti
12. er elements The Laser Head gets electrical power and control signals from the Controller via a 26 pin cable The laser system is CDRH compliant together with the CDRH model of the Controller and the Power supply unit The Laser Head has a manual shutter as well as a laser hazard label and a laser classification label 6 Cobolt Zouk Calypso Samba M Jive Flamenco Rumba 4 2 Controller The Controller supplies driving current and control signals to the Laser Head The operation setpoints are specific to each Laser Head and have been fixed during manufacturing The status of the laser operation is given via LED indicators POW green light Power is supplied Blinking LED indicates that the internal temperatures are stabilizing ON orange light Laser light is on in constant current mode LOCK orange light Laser light is on and the output power has been locked to setpoint The laser is operating according to specifications ERR red light An error has occurred No laser light The Controller can be configured in two ways decided at laser purchase CDRH Controller A key is supplied to be used to turn on the laser The laser will be running according to specifications in lt 3 min See Section 5 1 for more information The status of operation is monitored via LED signals Setting the turn key to its OFF position puts the laser in stand by mode OEM Controller The Controller is factory set so that no key is needed
13. go cobas O disable 1 enable through the standard warm up sequence see Section 5 1 cobas Get autostart enable state O disabled 1 enabled Get laser ON OFF state 0 OFF 1 ON Laser ON 11 Reguires autostart disabled Use this command for manual ON OEM models Laser OFF lO MALE Use this command for manual OFF OEM 15 Cobolt Zouk Calypso Samba M Jive Flamenco Rumba models p Get set output power Float W Set output power Ea gt et output power i e g p 0 050 for 50 mW pa Read output power Float W i Get drive current Float A slc Set drive current Float A Int 0 15 Bit O POWER ON Bit 1 LASER ON leds Status of 4 LEDs Bit 2 LASER LOCK Bit 3 ERROR 1 LED on 0 LED off O no fault 1 temperature error f Get operating fault p 3 open interlock 4 constant power fault cf Clear fault Enable disable direct control cobasdr s 0 disable 1 enable See sect 9 4 for description cobasdr Get direct control enable state O disabled 1 enabled sn Get serial number 32 bit unsigned integer Laser ON after interlock Forces the laser into Ocob1 autostart without checking if autostart is enabled OEM models cobasky Get key switch state O disabled 1 enabled Enable disable key switch With the key cobasky switch disabled the laser is not CDRH compliant O disable 1 enable and laser safety no longer applies For re starting t
14. he laser with control commands after having opened the remote interlock switch execute cf for clear fault followed by cob1 to restart the laser On CDRH models the key switch is the only way to re start The output power can be adjusted from 10 110 of nominal power using the p command Specifications are guaranteed at 100 of nominal power Recommended power range is 50 100 9 4 Direct control The Direct Control feature enables turning the laser ON OFF using a 5 12 VDC signal After having configured the Controller for Direct Control operation factory set or by executing cobasdr 1 the laser can only start up when 5 12V VDC max 12 5 VDC is applied to pin 3 on the analog connector with 0 VDC on pin 2 as reference Shifting the signal to O VDC on pin 3 will turn the laser off and put the laser in stand by mode status LED s is POW and not flashing This input only controls the on off state of the laser and cannot be used to modulate the power output 16 Cobolt Zouk Calypso Samba M Jive Flamenco Rumba 10 Thermal management To ensure operation within given specifications and for the warranty to be valid the Laser Head must be attached to a heat sink providing a thermal resistance of lt 0 2 K W The Cobolt heatsink meet this requirement This value is the difference between the maximum allowed Laser Head base plate temperature 50 C and the maximum specified ambient temperature at the air heatsink in
15. imited by a single space character ASCII 32 9 2 Handshaking Under no circumstances does the Controller initiate communication it only transmits characters in response to a message Every message to the Controller generates a response either a numerical value or the acknowledgment string OK In the event that the Controller receives a message that it cannot interpret it responds Syntax error followed by the complete command string minus the termination character that caused the error Every Controller response is terminated by a carriage return ASCII 13 and a full stop is used with floating numbers 9 3 Control commands The laser is delivered with the Controller set in autostart mode see Section 5 1 for autostart sequence description For system integration the autostart sequence can be disabled some commands require autostart disabled The controller is factory set for RS 232 communication 500 600 model number or USB communication 700 800 model number As long as power is supplied to the Controller the temperature control elements are always operating to reach set point values and the laser will be idle waiting for the next command All arguments are in lower case and separated by a space ASCII 32 Command Function Argument Returned value hrs Get laser head operating hours Float ilk Get interlock state 0 OK 1 interlock open Enable disable autostart With autostart disabled the laser will not
16. ll Cobolt support or your representative to identify corrective action LEDs Status Explanation Action off flashing POW X Mains power off Check connections POW x Temperatures not stabilised Check if heatsink is sufficient LOCK X Laser can not lock in constant power Check if heatsink is sufficient Contact current limit has been reached the factory ERROR on Error in laser parameters If lights at start up check cable connections if lights gt 5s after start up contact the factory 13 Warranty and maintenance Cobolt provides a system warranty of 12 months after delivery with unlimited number of operation hours The laser systems are designed for modular replacement or repair in the event that the Laser Head or Controller malfunctions Warranty is invalid if the laser system is operated outside of the specific limits and conditions as outlined in this document The Cobolt lasers are contained in sealed enclosures and should not be opened for any reason The warranty will be voided if any of the system units are opened All laser parameters are set at the factory and there are no adjustments required Maintenance is limited to wiping dirt off the enclosures and cleaning the aperture Clean the aperture with a standard photographers lens airbrush 19 Cobolt Zouk Calypso Samba M Jive Flamenco Rumba 14 Declaration of conformity CDRH model only The Cobolt 05 lasers are designed and manufactured to comply with EC Low V
17. ller set in Auto start mode As soon as power is supplied to the Controller the temperature control elements are operating to reach set point values and the laser emission will Start unless the keyswitch is enabled CDRH model 5 1 Installation startup operation 1 Mount the Laser Head on a Suitable heat sink see Section 10 2 Ensure that the interlock jumper is connected 3 Connect the Laser Head to the Controller with the Cable and fasten screws at both ends 4 Apply 15 VDC to power supply connector on Controller 5 The laser now goes through the following autostart sequence e Temperature stabilisation 1 2 min Status LEDs POW flashing then POW goes on e For CDRH model Turn key switch to start the laser Status LEDs ON goes on e The laser starts light is emitted in constant current mode pre set time of 60 sec Status LEDs ON goes on e The laser locks to pre set output power lt 2 min and operates according to specifications Status LEDs LOCK goes on 6 Switching the laser ON OFF to from stand by mode via control commands or Direct Control is described under Section 9 4 5 2 Closedown operation 1 Disconnect PSU from mains outlet turn the key switch to OFF first for CDRH model 2 Disconnect Controller from PSU 3 Disconnect Laser Head from Controller only required for shipping 9 Cobolt Zouk Calypso Samba M Jive Flamenco Rumba 6 Specifications 6 1 Optical full angle
18. lock amp Molex 90130 3206 Analog input 5 12 V gt laser on Analog signals Analog input lt 2 7 V gt laser off 6 4 Mechanical Dimensions Laser Head 125x70x45 mm 5x2 8x1 8 inches Controller 190x72x28 mm 7 6x2 9x1 1 inches PSU dimensions 115x50x35 mm 4 6x2x1 4 inches Fixation holes Laser Head size M6 fitting M4 spacing 115x55 mm Fixation holes Controller spacing 51x178 mm Cable Laser Head Controller 1 m length gt 8 cm bending radius Laser head weight 0 6 kg The information presented here is believed to be accurate and is subject to change without notice The specifications contained herein cannot be guaranteed outside of normal operational conditions 11 Cobolt Zouk Calypso Samba M Jive Flamenco Rumba 7 Mechanical outlines D4 5mm 0 2in 115mm 4 4 5in gt Beam position references Ec EWN vy N Ecl E c i o Laser Beam 105 5mm 4 2in 45mm 1 8in mm 0 1in lt 13mm 0 5in Laser Head mechanical outline model 05 01 dimensions in mm and inches 38 8mm 1 5in 21 6mm 0 fin 177 8mm Oin Ay ty m i i E jf E A E 4 a Analog amp interlock connector Power connector Data connector OEM amp CDRH Controller mechanical outline dimensions in inches and mm 13 Cobolt Zouk Calypso Samba M Jive Flamenco Rumba 8 Connector drawings amp pin assignment
19. oltage Directive and EC EMC Directive in their standard configuration of Laser Head Controller standard 1m cable and supplied with a Cobolt power supply unit The equipment might not conform to the CE directive if any part of the supplied equipment is replaced with a part not supplied by Cobolt The following harmonized standards are in use e Electrical safety IEC 61010 1 2010 UL 61010 1 CAN CSA C22 2 No 61010 1 e Laser Class IEC 60825 1 CFR 1040 10 2002 and 1040 11 2002 e EMC EN 61326 1 2006 incl EN 55011 Class A and FCC Part 15 subpart B class B In addition Cobolt laser products pass ETC 900 019 2 2 Transport and Vibration Standards including IEC 60068 2 64 IEC 60068 2 29 IEC 60068 2 32 and Shock and Vibration IEC 60068 2 29 Cobolt lasers are RoHS2 compliant as defined by the EC Directive 201 1 65 EU Disabling the key switch nullifies the CE marking as this violates the laser safety standard 15 Disclaimers Cobolt will assume no responsibility for damage incurred by faulty customer eguipment such as measurement eguipment cables etc used in conjunction with Cobolt lasers Cobolt makes no warranty of any kind with regard to the information contained in this guide included but not limited to implied warranties of merchantability and suitability for a particular purpose Cobolt shall not be liable for errors contained herein nor for incidental or conseguential damages from the furnishing of this information No par
20. t NET framework EULA 3 Setup will now connect to the internet and download Microsoft NET if it is required 17 Cobolt Zouk Calypso Samba M Jive Flamenco Rumba 4 After a few security screens setup will install NET and Cobolt Monitor A shortcut to software will be placed on the desktop and the program will run 11 2 Software instructions With the laser connected and powered select Options from the Tools menu The Port name drop down box shows a list of available COM ports Select the port which the laser is connected to and click OK If the laser is connected via USB it usually has the highest COM port number See Section 9 1 for correct port settings Com Port Settings Serial Port Port Name COM3 Baud Rate 115200 To connect to the laser choose Connect from the File menu The window should now show the correct laser Status along with various readings such as the laser power and current The five different sections of the user interface are described below ES CoboltMonitor 2 1 1 1 File Tools Help TEC Settings TECH Enabled Running Drive emp de Cobolt 3 50 00 35 00 E Laser Diode Settings Autostart a Set Power 212 0 mW Power 3400 A Curent PRES gt Laser Of Power Cal mW OEM Mode 5 Laser diode voltage HEETE V Set warm up current 2 800 Photo diode voltage MEZ V Set warm up time 60 0 Fault Vane Refresh Clear Faut Macr
21. t in this manual may be copied reproduced recorded transmitted or translated without the express written permission by Cobolt 16 Service If the laser does not function do not attempt to open any ofthe units or the warranty will be voided Call or e mail vour local Cobolt representative for consultancy and to reguest an RMA number see back cover for contact information If an RMA number us issued and the laser needs to be shipped back to Cobolt or your local representative please pack the complete system for shipment using the original package or eguivalent Ensure the unit is free from thermal paste before packing The warranty covers repair or replacing the unit at the option of Cobolt S Cobolt Contact Information Cobolt headquarters Cobolt AB Phone 46 8 545 91 230 Vretenv gen 13 Fax 46 8 545 91 231 SE 171 54 Solna E mail info cobolt se Sweden Web www cobolt se Sales representatives Australia Benelux Brazil Warsash Scientific Pty Ltd Phone 61 2 9319 0122 Fax 61 2 9318 2192 www warsash com au China China Daheng Group Phone 86 10 8278 2668 Fax 86 10 8278 2669 www cdhcorp com Estonia Latvia Lithuania Optek Ltd Phone 37 129 781 582 Fax n a www optek lv India New Age Instruments and Materials Phone 91 124 4086513 16 Fax 91 124 2331653 www newagein com Italy Optoprim S r l Phone 39 39 834 977 Fax 39 39 284 5269 www optoprim it Poland Amecam Phone
22. terface 40 C divided by the maximum power dissipated from the laser 50 W for the highest power models at high ambient temperatures The mounting surface should be flat within 0 05 mm over mounting surface It is recommended to use a thermal heat compound between the Laser Head and the heat sink to provide good thermal contact For assistance in thermal management and system integration please contact Cobolt s technical support Laser Head Heat Disipation va a C o a o va O Max disipated heat W o 20 25 30 35 40 45 50 Baseplate Temperature C Typical curve of heat dissipation with respect to base plate temperature under extreme operating conditions with good thermal contact between the laser head and the temperature controlled base plate 11 Cobolt Monitor software The Cobolt Monitor software provides a graphical way to monitor the laser performance and to change power operation mode and other settings The software can connect to the laser either via RS 232 port or via USB depending on the type of controller The USB driver must be installed manually and can be downloaded from the Cobolt website www cobolt se 11 1 Installation Microsoft NET is required to run the Cobolt Monitor software and this will be installed automatically if you do not already have the correct version Follow the following steps to install the software 1 Extract the archive and run the setup file 2 Accept the Microsof
Download Pdf Manuals
Related Search