Operating instructions hawos Oktagon
Contents
1. Operating instructions hawos Oktagon Congratulations Bs on purchasing gt T your Aawos flour pulls a M hawos d MES A 2 Safety is paramount A AAA a ci a ATTENTION A This device is not intended for use by persons Safety is paramount including children with impaired physical sensory or mental abilities or who lack A Only connect your mill to a properly installed experience and or knowledge unless they are socket with earthing contact supervised by a person responsible for their A Do not use defective units safety or have been instructed by such a A If the mains cord is damaged only the person in how to use the device Children manufacturer its customer service department must be under supervision to ensure that they or a qualified professional may replace it do not play with the device A Only authorised hawos professionals may A Never immerse the device in water perform repairs A Never operate your mill unattended hawos flour mills are equipped with an overcur A Never reach into the funnel or flour outlet rent circuit breaker that protects the motor from when the unit is operating risk of injury excessive current consumption e g if debris jams A Before opening the housing be absolutely sure the grindstones to pull the mains plug to prevent the unit from accidentally activating risk of injury Funnel eee Adjusting lever Br2. coarse with the motor turned on until the milling process starts again e Slowly set the lever back to fine page 4 figure 5 The mill is on but no flour is emitted If the grain is too wet or e g if spelt and oats are ground too finely the grindstones may be smeared Solution e Mill approximately 100 g brown rice semi coarse setting e f necessary open the grinder and remove any leftovers see the section Opening the grinder for this The mill turns off while in use Debris or clogged grindstones may cause the mill come to a standstill In such a case the overcurrent circuit breaker automatically deactivates the mill after approximately 20 seconds Solution e Remove any debris and or after the mill has cooled off mill approximately 100 g brown rice semi coarse setting The adjusting lever cannot be pushed to the fine setting If an overfilled flour bowl causes e g the flour to back up this may jam the grinder There is leftover grain or debris in the grinder Solution e When the mill is running change to the coarse setting and allow the grinder to run without any mill feed e f necessary open the grinder and remove any leftover flour and or debris If the grindstones are heavily laden clean them with a dry hard brush for this see the section Opening the grinder Opening the grinder Figure 6 Unscrew the top stone by turning it counterclock w
3. on to any subsequent user of the product 1 Removing the transport guard see page 4 Start up 2 Mill feed Please only use clean and dry grains You can determine this if the seed crackles distinctly when you crush it against a hard surface with a spoon Wet grain can be crushed and then looks like an oat flake Please consult the table of mill feed on page 5 when adjusting the fineness Please only mill sweet corn for grinding corn Only process mill feed with the device once 3 Power supply Only connect the mill to an alternating current source Check whether the existing mains voltage corresponds to the voltage specified on the base plate 4 Location The mill housing is made of wood Wood is a living material that is affected by changes in temperature and humidity which may cause it to crack You can best protect and care for the housing by not placing the mill close to radiators and not placing it right next to a stove steam moisture 5 Setting up the mill ZA During use place the flour mill on a hard level base kitchen countertop The slots on the bottom of the device may not be obstructed so that the motor can be ventilated Start up Start up Please first read through the section Before first use P 3 and the safety notes P 2 Be absolutely sure to remove the LA transport guard before first use You can remove the transport guard by removing the two brass screws fig
4. Corundum ceramic grindstone horizontally positioned 0100mm Weight BK 1039 Warranty 10 years The mill is conceived and designed for private household use The device is intended for grinding the mill feed listed on page 5 Any other use is deemed improper hawos assumes no liability for cases of improper use At the end of its lifecycle this product must be turned in at a collection point for recycling electric and electronic appliances The materials can be reused as labelled Please contact your community or city administration for the respective collection point hawos Service If you have questions about your mill please give us a call or write us an e mail our customer service team is happy to assist you Tel 49 0 6172 671749 e E mail info hawos de hawos Strong Mills Fine Flour hawos Kornmuhlen GmbH Ober Eschbacher StraBe 37 D 61352 Bad Homburg v d H Germany Tel 49 0 6172 40120 0 Fax 49 0 6172 40120 19 info hawos de www hawos de 10 12 2009_GB gon GA_Okta
5. ass screws ss bottom Rotating s grindstone Flour outlet On Off switch Before first use 1 CFA Dear mill owner We are delighted that you have decided on a hawos flour mill Your hawos will serve you well in preparing your natural food cuisine for many years to come Please observe the following notes before using it for the first time Please carefully read through these operating instructions to familiarise yourself with your hawos It will reward you with reliability and convenience Proper use The mill is conceived and designed for private household use The device is intended for grinding the mill feed listed on page 5 Product contents Mill funnel lid Brief instructions Connect to a properly installed socket with a protective earthing contact e Place the flour bowl under the flour outlet e Set the fineness with the lever e Fill the funnel with the desired grain e Turn the device on adjust the fineness as needed e Turn off the device once you have finished grinding e Only use the flour mill for grinding food A table of edible mill feed is provided on page 5 Before first use Before you use the device for the first time please first carefully read through the safety instructions and operating instructions Only in this way will you be able to use all functions safely and reliably Hold onto these operating instructions for future reference Pass these operating instructions
6. ccordingly for your reference However the values provided are approximate and are dependant on the moisture content of the grain If you wish to increase the fineness above the level specified in the table the end result will be super Mill feed table Mill feed Setting from level Wheat 1 Rye 1 5 2 Spelt 1 5 2 Barley 2 3 Oats 25 Millet 1 Sweet corn 0 Durum wheat 0 Rice not parboiled rice 1 Buckwheat 1 Green spelt 1 Flax seed mix 1 1 with wheat 2 Chick peas 1 5 Green peas 125 Nutritional yeast flakes 1 5 Quinoa 05 Amaranth slowly pour into the funnel 0 fine This increases the risk of the grindstones clogging Pay attention to the milling noise If it diminishes considerably then the grindstones are starting to clog Set the adjusting lever to coarser Turn off the mill once all mill feed has been processed If there is no mill feed in the grinder you can hear the grindstones rubbing against one another in the fine setting Cause Despite a high degree of precision the threading for the fine setting always has to have a small amount of play This small amount of play is neutralised when the pressure from milling is exerted on the two grindstones Grains that by nature have their own unique hardness exert a different milling pressure on the grinder For this reason we recommend different settings Feel free to also try foods that can be rolled and those that can be poured that are not indicated on the adjace
7. ise Figure 7 The black marks must be located over one another Figure 8 When screwing the grindstone back into place make sure that it does not tilt Figure 9 Make sure the foam rubber gasket is properly seated arrow Return the funnel to its previous position and secure it with the brass screws Opening the grinder A Attention Turn off the mill with the On Off switch and then disconnect the mains plug before opening the housing to prevent the device from accidentally turning on risk of injury e Remove the two brass screws on the left and right side page 4 figure 1 e Lift off the funnel page 4 figure 2 e Firmly turn the top grindstone up against the plastic ring counterclockwise until you are able to remove it figure 6 In order to reassemble the mill position the mill so that the flour outlet is pointing towards you e Place the top grindstone on the inner plastic ring such that it is completely level e The black mark must be at 6 o clock over the retainer figure 7 e Push the stone down gently from above and screw it back until it locks into place one complete revolution and then to approximately 10 o clock See Figure 8 for this Make sure the foam rubber ring is properly seated You can now return the funnel to its previous position and secure it with the two brass screws figure 9 Technische Daten Wousing Cid Beech Height mm 410 450 mn
8. nt table e g dry spices Proceed with care when trying new types and let us know about your results We are always delighted to learn more Oilseeds jam the grinder due to their high fat content For this reason mix mill feed with high fat content 1 1 with wheat or another grain 6 Cleaning Faults Cleaning A brush is integrated in the bottom rotating grindstone of your hawos which sweeps out the flour with every rotation thereby automatically cleaning the mill If you don t intend to use your mill for a prolonged period of time we recommend cleaning any leftover flour out of the grinder This is very easy with a vacuum cleaner Set the adjusting lever to coarse and then after having turned off the mill insert the vacuum cleaner nozzle into its funnel and flour outlet Do not in any case clean the housing with abrasive cleaners Never immerse the unit in water If necessary clean the housing with a damp cloth and then rub in a small amount of vegetable oil to preserve the surface Faults In the unlikely event of a fault you can rectify it easily The motor doesn t start Is the mill connected to a power supply Has the plug been properly connected with a socket Solution e Check both points and rectify the fault The motor hums but doesn t start running When turning off the unit grain may have clogged between the grindstones and may have jammed them Solution e Set the adjusting lever to
9. ure 1 on the housing and lifting off the funnel figure 2 Completely remove the three red screws with a cross slotted screw driver figure 3 Check that the foam rubber gasket is properly seated around the hole in the top grindstone figure 4 You can now return the funnel to ts previous position and secure it with the brass screws Milling Once connected to a power supply your hawos mill is ready for use Place a bowl under the flour outlet and adjust the fineness figure 5 Then fill the funnel with grain and turn on the mill Figure 1 Unscrew the two brass screws on the left and right Figure 2 Lift off the funnel Figure 3 Remove the 3 transport screws marked in red Figure 4 Make sure the foam rubber gasket is properly seated arrow Return the funnel to its previous position and secure it with the brass screws Figure 5 Set the fineness fine to the left coarse to the right Start up 5 Adjusting the fineness You can set the fineness of the mill feed steplessly between 1 and 9 using the adjusting lever When changing the setting from 9 to 1 the mill should either be on or the grinder must be empty The different types of grain and other mill feed differ considerably with respect to their fat and fibre content endosperms etc Our mill feed table is based on this hawos mills have undergone extensive testing and this table was compiled a
Download Pdf Manuals
Related Search