USER MANUAL
Contents
1. 90 degrees when han 90 degrees can cause the mower to ter than 90 degrees corner like follow 7 Care must be taken not to creat setting up virtual wire A corner sharper less t lose track of virtual wire We can make grea picture to avoid this situation Correct corner set up using several angle to avoid an angle of less than 90 Incorrect corner set up Virtual wire Proper set up in sharp corners gt 90 8 Redundant virtual wire back charging station must be cut Redundant virtual wire must be cut P14 9 A maximum virtual wire length of 200M wire diameter 1 0mm recommended Area requiring longer lengths should be broken into separate zones To be sure each zone should have a charging station 10 How to set virtual wire on the ground which has pool or trees 11 Connect two ends of virtual wire to patch jack located on charging station randomly there is no positive and negative 12 One mower in several gardens Please make sure that each garden should have located a charging station Contact your dealer for further information IMPORTANT INFORMATION If the working area is adjacent to water bodies slops or precipices the boundary wire should be supplemented with a fence or the like The height must then be at least 15cm This will prevent mower from ending up outside the working area under any circumstances P15 BLADES ADJUSTMENT The cutting height can be varied for 3cm or2. and check the efficiency of the blades B Ifthe blades are bent due to an impact or if it is worn out replace it 3 BATTERY A Attentions for lead acid batteries a Please don t remove the batteries privately b Storage 1 Charge the batteries at least once every six months of they are at 25 The interval of this charge should be reduced to 50 by each 10 C rise in temperature above 252 The self discharger rate doubles for each 10 C in temperature If they are stored for a long time in a discharged state their capacity may not recover ever after charge If the batteries are stored for more than a year at room temperature the life of the batteries may be shortened 2 Store the batteries starting from the fully charged state to prevent the life of the batteries being shortened 3 Use the batteries as quickly as possible after receiving them as they gradually deteriorate even under proper storage conditions B Attentions for lithium batteries a Please charge the lithium batteries in accordance with standard time and procedures b When the power is too low it should be started charging as soon as possible C Activation the lithium batteries should be normal charged discharged for 3 5 times to activate electricity back to normal capacity d Storage we suggest the optimum storage of lithium battery is with 4096 power and keep in the shade P19 TROUBLING SHOOTING The mower moves out of the area rounded b
3. will stop operation 6 Auto charging system When the mower is operating it feels powerless the cutting motor turn off at once and it will find the virtual wire then go alone it back to charging station for charging automatically this allows you to keep the charger connected with the charging station at all times even after the battery is fully charged The mower will going mowing after charging 7 Fuse protect the circuit There is a fuse hold on the back of mower next to charging jack it contains a one time use fuse in the event of a short circuit or power malfunction 8 Virtual wire The robot lawn mower can t operate without a virtual wire we suggest to use 100m of virtual wire It leads the mower back to charging station and the mower will take it as a wall when it is operating The mower will go on the virtual wire until it meets 4 charging sheet which is in front of charging station then get off virtual wire start cutting 9 Rain sensor There are two rain sensor on top cover of mower The mower can go back to the charging station automatically when it s raining 10 Two cutting models There are two cutting models of our mower go straight and go circle high efficiency We can choose the model from remote control 11 Cutting height adjustment There are two choice 3cm and 4cm 12 Infrared ray There are two infrared ray located in front of bumper which is functioned to reduce the running speed before th
4. 4cm Factory setting of blades is 4cm If the grass is long it is appropriate to let the mower start mowing at 4cm Once the grass is shorter you can change it lower with 3cm To adjust the cutting height 1 Stop the mower and take off the key 2 Turn over the mower to the underside It s easy to find that there are two blades fix on the Blades Holder Swing the 4 screws shows as follow picture And take blades out 3 There are two levels on the Blades Holder see right picture level 3cm and level 4cm View of Blades Holder 2 levels of cutting height 5 Turn over the mower to upside Cutting height adjustment finished Notice Use heavy gloves when inspecting or servicing the blades P16 POWER CONNECTION Firstly insert charger to charging station and then connect the charger plug to 110 240V power supplier iig Power supply 100 240V Notice The charger is not water proof therefore it must be located on a place which is dry And ventilated CHARGING There are two ways for charging 1 Charging by charger directly Powersupply 2 Through the charger station automatically 2 Powersupply P17 I eras 5 m ACCE THUE I NES Orr inci 9 IER 2 iesus nci NE atid 1 Take mower to Start point 1 meter in front of virtual wire see follow picture 4 Virtual Wire 2 Start the mower 1 0 Insert the key to switch and tru
5. ROBOT MOWER USER MANUAL Li e Please read this manual before use Please keep this manual for future reference SAFETY WARNINGS amp PRECAUTIONS 2 SAFETY INFORMATION amp WARNING LABELS ee 3 Robot Lawn Mower SAFETY eee 4 WHAT S IN THE 6 TECHNICAL INFORMATION mH Mmmm 7 MAIN PARTS s0esserscctetsssnevescencesttivecsececsstesauasrecedteeseanceess 8 CHARGING STAION INSTALLATION 11 SET UP VIRTUAL WIRE e IHR 13 BLADES ADJUSTMENT rrr enn 16 POWER CONNECTION mmm Hed CHARGING ONE EXER E E ET SE EDI UE Enea nte ut tht ctor ne c 17 TURN ON OFF THE MOWER Hm MMMMHHIeHmRm BMeR 18 CARE AND MAINTENANCE Bele 19 TROUBLING 5 5 55 20 EXPLODED rr nnn nara aka 22 SAFETY WARNINGS amp PRECAUTIONS 4 Read the owners operation manual carefully and follow all the safety and warning instructions 2 This machine has sharp rotation blades Never allow the mower to operate unattended keep bystanders children and pets away from mower when in operation 3 Never allow anyone to ride or ait on mower 4 Never allow anyone or person who is not familiar with the safe operation of the mower to operate the mower 5 Keep hands and feet away fro
6. ce towards the interior section of the lawn when installed Failure to do so may result in damage to property or persons P3 ROBOT LAWN MOWER SAFETY FUNCTIONS 1 Lift sensor There is a 45 degree sensor located on the PCB When the mower was lifted over 45 degree the blades will stop rotating immediately lt 2 seconds 2 Bumpers In front of the mower there equipped with three bumper board that will activate when the mower strikes solid fixed object when that object is at least 6 5cm in vertical height from the supporting surface of the mower When the bumper sensor is activated the mower will stop movement in that direction and reverse itself away from the obstacle 3 Two steps start the mower safety starting The mower has two steps to start it First step turn on the key switch and take off the key Second step press the emergency switch when the red light show the mow start 4 Emergency stop switch There is an emergency stop switch located at the back of mower which is next to the key switch red in color in the middle of the button If you press it in any case during operation the mower must stop all movement and stop the rotation of the blades immediately lt 1 seconds 5 Overload protect Each of the two blade motors and each of the two wheel drive motors are monitored continuously during operation for any situation that may cause these motors to over heat In the event this is detected the mower
7. e charging pins of the mower 21 Do no spray water directly into the docking area of the charging station or onto the operating panel of the charging station 22 The mower has sharp rotating blades Please care the mower when itis mowing in case of serious injury occur 23 Keep the lawn mower in perfect operating conditions by performing the maintenance procedures outlined by the manufacturer Good maintenance guarantees better performance and longer service life 24 In order not to irreversibly damage electric and electronic parts do not wash the robot with water jets at a high pressure and do not plunge it partially or thoroughly in water as it is not watertight 25 It is absolutely forbidden to use the robot in explosive and flammable environments 2 SAFETY INFORMATION amp WARNING LABELS 1 2 3 4 6 1 WARNING this is a dangerous power tool Use care when operating and follow all safety instructions and warnings 2 Read the owner operating manual carefully and follow all safety instructions 3 Objects can be thrown from mower while operating take caution 4 Keep children pets and bystanders away from mower 9 Sharp rotating blades Keep hands away and do not attempt to lift mower from this area 6 Sharp rotating blades Keep feet away DANGER Sharp rotating blades Keep hands and feet away Serious injury can occur CE Rohs approved Input and output of mower The charging station fence must fa
8. e mower 3 Turn off the mower and charge it manually Change batteries Check whether the charger is well connected Charge again until the power light green Replace the battery and follow the maintenance Cut the grass appropriate height Send the mower to provider and repair to change the micro switch Raise ground clearance to the uppermost position Raise cutting height Fill in all holes cover or exclude all exposed roots in order to smooth the terrain Mower does not complete the edge Mower lamp not flashing when the blades are in operation Mower drives but blades will not mow short run time operates less time than normal Mower does not detect the charging station contacts Mower reached the charging station when its contacts are above the charging station contacts The robot is very noisy The robot behaves in an anomalous manner around the flower beds Obstacle along the path Faulty power lamp 1 Mow on remote control has been turned off 2 The cutting motor is broken Power is not fully charged for operation 1 Power supply is not plugged into the main power supply 2 The ground before the charging station is not flat Height difference between the charging station and the lawn surface at the entrance to the charging station No power to plug receptacle or main power is shut off 1 Damaged cutting blades 2 cutting blade flooded by residues tapes ropes plastic fragme
9. e mower connect charging station 13 The mower goes clockwise to enter the assigned area mowing until it is low power Elements of mowing process P5 WHAT S IN THE BOX 1 Robot Lawn Mower HS Charger Used for recharging the robot directly 5 Virtual wire 100m Used to mark mowing area and create a virtual wall for the mower 7 Remote control Control the mower 9 Blades Two blades pre installed on the mower and two extra 11 Keys 2Pcs Used for turn on the mower P6 2 Charging station Used for directing the robot lawn mower to the charging contacts 4 Stakes 4Pcs Used for fix the charging station to the ground 6 Pegs 100Pcs Used for fix the virtual wire to the ground around the lawn perimeter and around obstacles 8 Remote control battery For remote control use 10 Fuse 12 English use manual TECHNICAL INFORMATION Power supply input 100 240V 50 60HZ Output 24V Robot lawn mower technical information DESCRIPTION Coverage for one time charge Working capacity Virtual wire maximum length diameter suggest Virtual wire length diameter Mower size Charging station size Carton size Power Noise Cutting blades Cutting width Cutting Height Cutting speed Blades rotate speed Hill capability Max ambient functioning temperature Average working time Wireless remote control Battery GW NW Charging time for battery Rain sensor Aut
10. m the cutting blades and other moving parts 6 Never attempt to service or adjust the mower while it is in operation 7 Inspect and clear the mowing area of all debris toys tree branches items of clothing etc before operating the mower 8 Never raise the mower or attempt to inspect the blades while the mower is operating 9 Always turn off the power before lifting the mower or attempting any adjustment 10 When operating the mower in manual mode maintain a safe distance from behind or around the mower and wear proper foot apparel 11 Do not operate the mower on slopes greater than 20 degrees or use it in manual operation on slopes where a firm footing is not possible 12 Do not operate the mower if any safety feature or device is damaged or inoperable 13 Do not attempt to disable or defeat any safety feature or device 14 Use heavy gloves when inspecting or servicing the blades 15 Wear eye protection and use gloves when installing the virtual wire and driving the wire stakes pegs Firmly drive all pegs in order to keep the wire from becoming a tripping hazard 16 Do not use the charging station power supply with an extension cord 17 Use only the original equipment power pack and power supply charger with this mower 18 Do not use the power supply charger if the cord has become damaged 19 Do not place metal objects in the area of the charging contacts on the charging station 20 Do not place metal objects across th
11. n the mower 20 Firstly Insert the key to switch and trun Gon the mower then pull out the key Secondly press emergency button the mower started 3 Turn off the mower 1 0 Turn Goff the mower and then pull out the key 2 0 Firstly press the emergency button to stop the mower Secondly trun off the mower and pull out the key Motice Do not start mower on virtual wire directly while the machine has just finished charging It s needs to be put on to start point and restart it Otherwise may cause a jerious injury IMPORTANT INFORMATION Rol xot lawn mower cannot be used before the installation is complete P18 CARE AND MAINTENANCE 1 CLEAN THE ROBOT EVERY MONTH AS FOLLOW A Stop the robot in safety conditions B Clean all the outside surfaces of the robot with a sponge soaked in warm water C Do not use solvents or benzene so not to damage the varnished surfaces and the plastic components D Do not wash the inside parts of the robot and do not use water jets in pressure so not to damage the electric and the electronic components E Check the lower part of the robot cutting blade area and wheels and remove the deposits and or residues that might obstruct the correct functioning of the robot F To remove the deposits and or other residues form the blades use a suitable brush G Clean the outside of the recharging station from any accumulated residues 2 CHECK TWO BLADES EVERY WEEK A Clean
12. nts 3 the start of the robot occurred with obstacles being too close less than 1m away or in presence of unexpected obstacles fallen branches forgotten objects etc 4 damaged electric motor 5 Grass too high Virtual wire incorrectly placed Charging station the virtual wire corrosion Mower is operated in the zone with the charging station but stopped P21 Watch the full operation of edge and confirm no obstacle are present Replace operation lamp 1 Turn on the mower button 2 Send the mower to maintenance station and replace a new cutting motor Charge again until the power light green 1 Confirm power supply is plugged into the main power supply 2 Reset the charging station in a flat place Confirm the ground before the charging station is leveled with the charging station if necessary fill area with dirt and level off Check the power Check the plug 1 Replace the blade with a new one 2 Stop the robot in safety conditions Use protection gloves to avoid the risk of cuts on hands Remove the fold cause from the blade 3 stop the robot in safety conditions Remove the obstacles and restart the robot 4 Get the motor repaired or replaced by nearest maintenance station 3 Increase the cutting height Carry out preliminary cutting of the area with a normal lawn mower Relocate the virtual wire Check the charging station contact your provider id the contacts is replaced Turn off
13. o recharge Intelligent spiral Go straight Anti theft security Waterproof Warranty mower SPECIFICATIONS 600m2 2096 depends on the conditions of lawn 1500 m2 20 depends on the conditions of lawn 200m 1 0mm 100m 0 5mm 56 51 25cm LW H 38 5 44 5 18cm LW H 77 51 5 28 LW H 82W 65db 4pcs 2 pre installed and 2pcs extra 28cm 14 3cm 4cm 20m min 5000 rpm 3 10 45degree Max slope AQ C 2 3 hours Within 10m lead acid lithium battery24V 7 2AH 20KG 17 5KG with lead acid batteries 17KG 14 5KG with lithium batteries 3 4 hours Yes Yes standard Standard Yes 2pcs key Lift sensor buzzer Yes IPX5 1years 7 MAIN PARTS ue 1 Robot lawn mower A Bumper mower will stop and change direction when it meets obstacles B Charging point Infrared ray while mower follow virtual wire back to home it will reduce speed before it meets charging station D Handle E Tyre cover take it out and change the tyre F Safety hence keep off foot and hands G Omni directional wheels H Product date Handle J Blades P8 A Fuse Protect the mower when it is overloading B Charge plug C Rain sensor Mower go back home automatically when it rains D Power light turn red if the mower is on E Power switch x on off The key cannot be pulled out when switch on 2 Charging station A Charging shee
14. the power by keys and takes it to charge 1 Upper cover 2 Bottom cover 3 Plastic wheels 4 Shell 5 Batteries 6 Cutting motor 7 motor 8 Axle 9 Bumper 10 Motor gasket 11 Gear 12 Motor pressure plate 13 Bearing pressure plate P22 14 Batten of battery 15 Handle 16 Rain sensor copper head 17 Springs copper sheet 18 Bearing 19 Blades 20 Blades holder 21 O0mni directional wheels 22 Charging copper head 23 Sensor board 24 Main circuit board 25 Micro switch
15. ts B Guide channel C Charging light D Stakes hole E Virtual wire light F Charge plug G Patch jack Connect the virtual wire randomly There is no positive and negative A Fuse Protect the mower when it is overloading B Charge plug C Rain sensor Mower go back home automatically when it rains D Emergency switch turn on key press this button and it turns red then the mower start Press this button at any time the mower stopped E Power switch The key be pulled out when switch on Red charging Green full charged or idle Red broken wire idle Colorless good wire connecting P9 3 Remote control A Remote control analyzing Power light 9 Power Switch Model Go straight Go circle L Go lift R Go right Home Back to charging station Mow Turn on mowing Turn off mowing B Replacement of remote control battery Used 23A 12V battery 4 Fuse replacement Loosen cover and replace with a new fuse P10 1 Choose installation place please make sure which is flat no water the charging Station is not water proof no magnetic interference and no obstacle in the front of charging station Virtual Wire N X P Charging Station Best install Place 4 Make sure it s flat P 2 No magnetic interference 3 No water 4 No obstacle in front 2 Fix the charging station with stakes P11 3 Lay virtual
16. wire in the middle of charging station 4 Please fix the charging station in level place Notice g Before fix the charging station on the lawn you should examine your lawn and decide the best location which is easy for the mower to find the station to recharge Notice Hard or dry ground may cause pegs to break when Driving them in In extreme cases watering the lawn where the pegs will be driven 5 Never use a high pressure washer or even running water to clean the robot lawn mower P12 SET UP VIRTUAL WIRE 1 Dig virtual wire with pegs 1 meter per piece 2 f a high obstacle for example a wall or fence borders the working area the boundary wire should be laid 35CM from the obstacle 3 A minimum distances from the charging station and any obstacle is 2 meters Make sure the distance from corner to charging station is at least 2 meters 4 Make sure to lay a 2 5 meter minimum straight line of virtual wire in front of charging station 4 Virtual Wire of 5 The distance between charging station and virtual loop should at least 2 5 meters P13 s and fasten it on the ground with pegs 50 that the 6 Bury virtual wire below gras keep the virtual wire mower should not cut the wire If the grass grow up we can stil as before Add pegs in order to pull the virtual wire down to the ground surface Virtual wire below the grass tips e a corner sharper shorter than
17. y the virtual wire or moves in circle searching for the virtual wire The mower does not work The mower buzzed The remote control does not work The batteries can not recharge Large patches of uncut grass remain after mower has completed mowing The bumper does no activate when meeting obstacle Mower gets stuck frequently when traveling optimal terrain Possible reasons The virtual wire fails to send signals The virtual wire is broken by the mower 1 It is trapped in the lawn 2 1 moves to the area where the grass is thick 3 The mower was lifted over than 45 degree 1 The power button on the remote control is touched 2 The mower was lifted over than 45 degree 3 Blades are plugged up seriously and the power becomes inefficient 4 The mower stop when he can not meet the virtual wire in 9 minutes The electricity power is low Power is not fully charged for operation Power nearing natural end of life Grass is extremely overgrown or very wet Micro switch is broken Low ground Cutting height too low Terrain needs landscaping repairs P20 Solutions Check the virtual wire light Be sure the virtual wire is connected to the charging station that is in motion and there is no loose place Clear the lawn where the mower is trapped or restart the mower in another place Then the mower will work in a new circle 1 Press power on amp off button again 2 Restart th
Download Pdf Manuals
Related Search