User Manual of WD703 Specification Item No
Contents
1. Switch Mode LED Lights Sensor Head Sensor Shield Power Input Hole Solar Panel Power Plug Power Cord 5M Components L Rack x2 Clipper for L Rackx2 Screw Nutx2 Butterfly Screw x2 AC OF wy Screw x4 Screw Wrap x4 Sensor Shield x2 Installation of Solar Panel 1 Make sure the location to be easily receive sunshine 2 Mark location of where you want to install solar panels 3 Drill hole that is diameter 6mm and depth 33mm 4 Put the screw plastic holder into the hole 5 Put the panel screw holes onto the wall hole then fix with screws Screw Hole Note 1 Make the appropriate angle adjustments to receive best sunshine 125 2 Can also use L rack to install the solar panel Installation of Light Fixture 1 Loosen the screw on the bottom of main body then take out the base part 2 Mark location of where you want to install solar panels 3 Drill hole that is diameter 6mm and depth 33mm 4 Put the screw plastic holder into the hole 5 Put the screw holes which is on the base part onto the wall hole then fix with screws 6 Put main body close to the base part make sure to fully inserted of both sides 7 Put the solar panels power plug in the socket on the body Loosen the screw Put plug of panel into the socket 2 Can also use L rack to install the main body D Z Zz Put plug of panel into the socket L Rack Screw Nut Adjustment of Lighting angle Lamp2. head can be adjusted down to 50 degrees Lamp head can be adjusted about 70 degrees forward to left right sides O 70 O Turn Left Right 70 ea Switch Mode Off Keep lamps off put switch to left On Keep lamps on put switch to Center Auto Keep lamps inducting automatically put switch to right When switch to AUTO lamps will be warm up for about 30 seconds then the lamps are off when warm up completed Switch Mode CHD Gp Gp OFF ON AUTO Sensor detection range en T Se Usage of Detection Shield According to the actual installation status using their own sensor range shield to narrow the range of induction Purpose of Detection Shield 1 Change the sensor distances and angles 2 Get to limit the detection distance and angle to make it more focused How to Use the Detection Shield 1 Cut the partial shield by scissors along the incised line 2 Put the shield on the sensor head Examples of Using Sensor Shield 4m 110 Battery Change 1 Loosen the lamp body screws and remove the base part 2 Remove the battery cover change battery by following up the indication of direction 3 Replace battery cover install base part with screw locking oY O hah f f j Siege fN i j ii sisi j m Loosen the Screw Battery Cover Trouble Shooting Statement Sensor not workab
3. User Manual of WD703 Specification Item No WD 03 Product Name LED SOLAR SENSOR LIGHT TWIN LIGHT Voltage DC4 8V 1 2V 6 00mAh Ni MH Battery AAx4 LED Made in Taiwan 1W LEDx2 White Waterproof IP44 Lighting Time 10 Sec Working Ambient Light of AUTO Mode 10 LUX Raw Material ABS Dimension H12 x W16 x D13 2 cm Net Weight 0 94kg Accessory Operation Manual Screws Detection Shield L Rack Plastic Clipper Working Environment Outdoors Dimension mm Unit mm 160 so 47 a 132 E p a A D f jE i Pi f n pe Ses l ew a rat T AREA t t _ Sey PA 66 85 85 64 133 Notes Not allowed to disassemble repair alteration avoid danger fires Do not look directly at the lamp when lighting so as not to cause eye irritation The product waterproof grade is IP44 but do not put in a large rain wash or rinse water directly Wipe with diluted neutral detergent do not use alcohol solvent Do not install in the place under high temperature air conditioning output heating appliances and where has obstacles The recommendation Installation height is between 1 8 to 2 5 meters In order to get better ventilation should leave 10 cm to ceiling and 1 am to wall when installed Keep installing perpendicular to the ground Being Installed slanted will easy to lead to abnormal induction or cause leakage Feature
4. le when objects in the sensor range Lamps on but no objects in the detection range Possibility No power incoming Not proper setting of sensor direction Objects moving directly forward to the sensor Interrupted by obstacles Dirt on Sensor lens Some mistakes are from 1 Other lighting devices or air conditioning 2 cats dogs 3 some waving things 4 The heat of cars or front light 5 powerful interference Set too wide range or too large distance O A f j K Fj f co G y f ji P l eg E i j Treatment e Make sure plug the socket properly eMake sure have workable battery e Make sure the solar panel is at proper use eChange location of sensor or adjust detection range eRelocate the sensor or change the detection direction eMove away the obstacles or relocate the sensor eWipe with soft rinse cloth eMove away those interference or change location eReset range and distance or use detection range shield
Download Pdf Manuals
Related Search