FX5401 Embedded Computers Small System User's Manual
Contents
1. In addition to the traditional driverA and C optionsinclude IDE hard drivers D E and F plusa SCSI hard driver and CD ROM drive USB CD ROM and USB HDD Available options C CDROM A SCSI USB FDD USB HDD USB C DROM Disabled Enabled Default setting C CDROM A Swap Hoppy Drive The field reversesthe drive letter assignments of yourfloppy disk drives in the Swap A B setting otherwise leave on the default setting of Disabled No Swap This works separately from the BIOS Features floppy disk swap feature It is functionally the same as physically interchanging the connectors of the floppy disk drives When the function s setting is Enabled the BIOS svapped floppy drive assignments so that Drive A becomes Drive B and Drive B becomes Drive A under DOS Available options Disabled Enabled Default setting Disa bled Boot Up Hoppy Seek During POST BIOS will determine if the floppy disk drive installed is 40 or 80 tracks 360K types are 40 tracks while 760K 1 2M and 1 44M are all 80 tracks Enabled JBIOS searches for floppy disk drive to determine if it is 40 or 80 tracks Note that BIOS cannot tell from 720K 1 2M or 1 44M drive type asthe are all 80 tracks Disabled BIOS will not search for the type of floppy disk drive by track number Note that there will not be any waming message if the drive installed is 360K Boot Up Numloc k status This field is used to activate the Num Lock function upon system boot If th2. Please checkthe battery and change a new one when necessary DISK BOOTFAILURE When you can t find the boot device insert a system disk into Drive A and press Enter gt Make sure both the controller and cablesare allin proper positions and also make sure the disk is formatted Then reboot the system DISKETTE DRIVES OR TYPES MISMATCH ERROR When the diskette drive type is different from CMOS please run setup or configure the drive again ERROR ENCOUNTERED INITIALIZING HARD DRIVE When you can t initialize the hard drive ensure the following things 1 The adapterisinstalled conectly 2 Allcablesare correctly and firmly attached 3 The correct hard drive type is selected in BIOS Setup ERROR INITALIZING HARD DISK CONTROLLER When this emor occurs ensure the following things 1 The cord isexactly installed in the bus 2 The correct hard drive type isselected in BIOS Setup 3 Whetherall of the jumpersare set correctly in the hard drive FLOPPY DISK CONTROLLER ERROR OR NO CONTROLLER PRESENT When you cannot find orinitialize the floppy drive controller please ensure the controller is in proper BIOS Setup If there isno floppy drive installed ensure the Diskette Drive selection in Setup is set to NONE KEYBOARD ERROR OR NO KEYBOARD PRESENT When this situation happens please check keyboard attachment and no keys being pressed during the boot If you are purposely configuring the system without a keyboard set the error halt condition in BI
3. Wideo EGA UGA Halt On Ho Errors ESE Quit tl Select Item PUSPDS 2 Hodify F1 Help CShift F2 z Change Color Date amp Time Setup Highlight the lt Date gt field and then press the Page Up Page Down or 4 keys to set the curent date Follow the month day and year format Highlight the lt Time gt field and then press the Page Up Page Down or keys to set the current date Follow the hour minute and second format The usercan bypassthe date and time prompts by creating an AUTO EXEC BAT file For information on how to create thisfile please referto the MS DOS manual Hoppy Setup The Standard CMOS Setupzoption records the types of floppy disk drives installed in the system To enter the configuration value fora particular drive highlight its comesponding field and then select the drive type using the left or right amow key Hard Disk Setup The BIOS supports various types for user settings The BIOS supports Pri Master Pri Slave gt so the usercan install up to two hard disks Forthe masterand slave 18 FablATech Corporation jumpers please referto the hard disk s installation descriptions and the hard disk jumper settings You can select lt AUTO gt under the lt TYPE gt and lt MODE gt fields This will enable auto detection of your IDE drives during boot up This will allow you to change your hard drives with the poweroff and then poweron without having to reconfigure your har
4. least significant byte Divisor latch most significant byte X MODEM control Receiver Buffer Register RBR Bit 0 7 Received data byte Read Only Transmitter Holding Register THR Bit 0 7 Transmitterholding data byte Write Only Interrupt Enable Register IER Bit 0 Enable Received Data Available Interrupt ERBFI 54 FablATech Corporation Bit 1 Enable Transmitter Holding Empty Interrupt ETBEI Bit 2 Enable Receiver Line Status Interrupt ELSI Bit 3 Enable MODEM Status Interrupt EDSSI Bit 4 Must be 0 Bit 5 Must be 0 Bit 6 Must be 0 Bit 7 Must be 0 Interrupt Identification Register IIR Bit 0 O if Interrupt Pending Bit 1 Interrupt ID Bit O Bit 2 Interrupt ID Bit 1 Bit 3 Must be 0 Bit 4 Must be 0 Bit 5 Must be 0 Bit 6 Must be 0 Bit 7 Must be 0 Line Control Register LC R Bit 0 Word Length Select Bit O WLSO Bit 1 Word Length Select Bit 1 WLS1 Bit 2 Number of Stop Bit STB Bit 3 Parity Enable PEN Bit 4 Even Parity Select EPS 55 FablATech Corporation Bit 5 Stick Pa rity Bit 6 Set Break Bit 7 Divisor Latch Access Bit DLAB MODEM Control Register MCR Bit 0 Data Terminal Ready DTR Bit 1 Request to Send RTS Bit 2 Out 1 OUT 1 Bit 3 Out 2 OUT 2 Bit 4 Loop Bit 5 Must be 0 Bit 6 Must be 0 Bit 7 Must be 0 Line Status Register LSR Bit 0 Data Ready DR Bit 1 Overrun Eror OR Bit 2 Parity Error PE Bit 3 Framing Error
5. state to high state Bit 3 A lin this bit position selects the printer Bit 2 A Ostarts the printer 50 microseconds pulse minimum Bit 1 A 1causesthe printer to line feed after a line is printed Bit O A 0 5 microsecond minimum highly active pulse clocks data into the printer Valid data must be present fora minimum of 0 5 microseconds before and afterthe strobe pulse 60
6. ISA assigned PCI ISA PnP assigned PCIFISA Por assigned z PCLAISA PnP assigned Legacy ISA assigned Legacy ISA assigned PCL TSA Por assigned PCI ISA PnP assigned PCI ISA PnP assigned PIISA Por assigned PCISIZA PnP Guat tj Select Item assigned PCIFISA Por Help PUYSPOS Modify assigned PCTFISA Por Old Values Shi1ftJF2 Color assigned PCISIZA PnP Load BIOS Defaults assigned PCIFISA PoP Load Setup Defaults PNP O S Installed Set to Yesto inform BIOS that the operating system can handle Plug and Play PnP devices Available Options Yes No Default setting No Resources Contolled By Auto Manual If you select Auto all the interrupt request IRQ DMA assignment and Used DMA fields disappear asthe BIOS automatically assignsthen The default value is Manual Available Options Auto Manual Default setting Manual Reset Configuration Data Enable Disable If you select Enable to reset Extended System Configuration Data ESCD when you exit setup is you have installed a new add on and the system reconfiguration has caused such a serious conflict that the operation operating system cannot boot Available Options Enable Disable Default setting Disable 30 FablATech Corporation IRQ n DMA n Assigned PCI ISA PnP Legacy ISA The resourcesare controlled manually 1 Legacy ISA Devicescompliant with the original PC ATbus specification requiring a specific inter
7. O AA CZ EE 5 Chapter 2 Hardware Installation 1 ss 2v senssasmsssenarezenaaaaz zana tE P S na aan nass a n auae KASZA KASZA 7 Before Insta lation toe c at Ep Lee ER A EE LR Ie Roa WE 7 Removing Covers Installing HDD or Compact Fan 8 Connecting the Monitor Keyboard Mouse een 9 Connecting the COM portsand Parallel Port eee 10 Connecting the LAN ports and UERborts eee eee 11 Connecting the DC PowerJackand Power witch lt 13 Connecting the Audio Microphone In Speak Out 13 Chapter 3 BIOS Setup EE 15 VOT N tee OE OE ZZ AE DEO 15 BIOS Functio In 16 Keyboard Convention 17 Standard CMOS Setup TEE 18 BIOS Features Setup rario etienne ded dhi nie i dor 21 Chipset Features SETUP EN 25 PowerManagement sai owania a a aaa dawa 28 PCI Plugrand Play cue E kia EA EO O vl ne dv r ate 30 Penpheral Setup 2 idht M RE RLA ENS 32 uzE Ies iom 35 Chapter 4 Software Installation 11e s re nese eren ene nenet senes anna sanata annua n aaa n ne nenen a nS an uana 37 Installation WIN 95 98 oai t eie nt in gen nm eae Des ede vec crant erg nds 37 Mcr Nene M 37 WIN98 WINO95 Driver nennen teze rene eee KRK RK EK RER R PKR nnee nna 37 LAN Utility S DIVET sea ata stay el ea vedere e ee M 38 Kudo DIVE ERAT TERI TUI 38 WIN 95 98 DTIVOF 2 rrr een eve dr atts e RR ees d 38 Watchdog TME EE 39 Watchdog Time
8. disk space with HDD clamp holder u Powerrequirement 24V with 2596tolerance 0 8A minimum a Dimensions 1U height 130 0mm D x 200 0mm W x 44 2mm H Fabl Tech Corporation Packing list Upon receiving the package verify the following things Should any of the mentioned happens contact usfor immediate service Unpack and inspect the FX5401 package for possible damage that may occur during the delivery process Verify the accessories in the package according to the packing list and see if there is anything missing or incorrect package is included If the cable s you use to install the FX5401 is not supplied from us please make sure the specification of the cable s iscompatible with the FX5401 system Note after you install the FX5401 it is recommended that you keep the diskette or CD that contains drivers and document files and keep the document copies or unused cablesin the carton for future use The following lists the accessoriesthat may be included in your FX5401 package Some accessories are optional items that are only shipped upon order One FX5401 embedded system One AC to DC 24V poweradapterand 1 AC powercode One 2 5 HDD clamp holderaccessory pack One Y type 3 terminal PS 2 keyboard plus mouse port adaptercable Optional L type universal fixers and 6 screws 6 stamp pads for this enclosure One compact disc includes software utility FablATech Corporation Fab
9. 0BFFF Shadow Boot Up Humlock Status On DCOOO DFFFF Shadow Gate AZ0 Option Fast Typematic Rate Setting Disabled Typematic Rate Chars ec 6 Enabled Disabled Disabled Disabled Disabled Disabled Disabled Typematic Delay Hsec 250 Security Option Setup PCI UGR Palette Snoop Disabled DS Select For DRAW gt 64HB Han OS Report Ho FID For WIH 95 Ho Quit tl Select Item Help PUZPDZ 7 2 Modify Old Values CShift3F Color Load BIOS Defaults Load Setup Defaults Virus Waming This option may flash on the screen During and afterthe system boots up any attempt to write to the boot sectoror partition table of the hard disk drive will halt the system and the following eror message will appear in the mean time you can run an anti virus program to locate the problem Available Options Disabled Enabled Default setting Disa ble CPU Intemal Cache This functions speeds up memory access The FB2510 G XM Cyrix CPU hasan intemal cache Available options Disabled Enabled Default setting Enabled Quick Power On Self Test This option speeds up Power On Self Test POST after you power on the computer If it is set to Enable BIOS will shorten or skip some items checks during POST 21 FablATech Corporation Available options Disabled Enabled Default setting Enable Boot Sequence This field specifies which device the system looks first upon poweron The item has different boot sequence optionsof three drives each
10. FE Bit 4 Break Interrupt BI Bit 5 Transmitter Holding Register Empty THRE Bit 6 Transmitter Shift Register Empty TSRE Bit 7 Must be 0 MODEM Status Register MSR Bit 0 Delta Clearto Send DCTS Bit 1 Delta Data Set Ready DDSR Bit 2 Training Edge Ring Indicator TERI Bit 3 Delta Receive Line Signal Detect DSLSD 56 FablATech Corporation Bit 4 Clearto Send CTS Bit 5 Data Set Ready DSR Bit 6 Ring Indicator RI Bit 7 Received Line Signal Detect RSLD Divisor Latc h LS MS Ln ose a Bit 1 Bit 9 Bit 3 Bit 4 Bis ate Bi Desired Baud Divisor Used to Generate 16x Rate Clock 57 FablATech Corporation Parallel Ports Register Address PorAddress Read Wiite Base 0 Input data Printer satus buffer Base 2 Write Printer control latch Printer Interface Logic The parallel portion of the SMC 37C 669 makes the attachment of various devices that accept eight bits of parallel data at standard TIL level Data Swapper The system microprocessorcan read the contents of the printers Data Latch through the Data Swapperby reading the Data Swapper address Printer Status Buffer The system microprocessor can read the printer status by reading the address of the Printer Status Buffer The bit definitions are described below 7 6 5 4 3 2 1 0 FIL AL AL LILI ERROR SLCT PE ACK BUSY NOTE X represents not used 58 Fa
11. Fabl Tech Corporation IPC Solution Website http www fabiatech com Email supportefa biatech com FX5401Embedded Computers Small System User s Manual FEB 2005 Version 1 1 Part Number FX5401 Copyright Copyright 2002FablATech Corporation The content of this publication may not be reproduced in any part orasa whole transcribed stored in a retrieval system translated into any language ortranscribed in any form orby any means electronic mechanical and magnetic or otherwise without the prior written permission of FablATech Corporation Disclaimer FablATech makesno representation of warranties with respect to the contents of this publication In an effort to continuously improve the product and add features FablATech reservesthe right to revise the publication or change specifications contained in it from time to time without prior notice of any kind from time to time FablATech shall not be reliable for technical or editorial emors or omissions which may occurin thisdocument FablATech shall not be reliable for any indirect special incidental or consequential damages resulting from the fumishing performance oruse of thisdocument Trademarks Trademarks brand namesand products names mentioned in this publication are used for identification purpose only and are the properties of their respective owners Technical Support If you have problems or difficulties in using the system orsetting up the relevant device
12. I ISA BIOS CeAds4F 5 CHIPSET FEATURES SETUP AWARD SOFTWARE IMC SDRAM CAS latency Time SDRAM Clack Ratio Diw By 16 bit I O Recovery COLE S bit I O Recovery LEJ USE Controller Enabled USB Legacy Support Disabled Video Memory Size 1 5 M Display status CRT Flat Panel Resolution 640x430 Quit fl Select Item Help PUYSPOS Modify Old Values CShiftJF2 Color Load BIOS Defaults Load Setup Defaults SDRAM CAS AUTO Latency Time This field specifies the latency for the Synchronous DRAM system memory signals Available Options 3T 2T Default setting 3 T SDRAM Clock Ration Div by When 100 MHz extemal frequency runsthe system the system will run at 3 cycle clocks When 66 MHz runs the system the system will run at 4 cycle clocks Selecting Auto the system willbe auto adaptive depending on the SDRAM clock that is installed Available Options 4T 3T Default setting 3 T Shit I O Recovery Time The recovery time isthe length of time measured in CPU clocks which the system will delay afterachieving an input output request This delay takes place to wait forthe I O to complete the request This field specifiesthe recovery time for 8bit VO Available Options Disabled 1 8 Sysclk 25 FablATech Corporation Default setting 5 Sysc Ik 16Bit I O Recovery Time This field specifies the recovery time for 16Bit VO Available Options Disabled 1 8 Sysclk Default setting 5 Sysc Ik USB Contro
13. LAN directory a HELPME EXE file is included to provide installation information Audio Drivers WIN 95 98 Driver 1 To install the VGA driver insert the CD ROM into the CD ROM device and enter DRIVER gt AUDIO gt NS5530 gt WIN98 If your system is not equipped with a CD ROM device copy the VGA driverfrom the CD ROM to a 1 44 diskette Execute CYRIXM 1 EXE file The screen showsthe SETUP type Pressany key to enterthe main menu Asthe setup is completed the system will generate the message as follows Yes want to restart my computer now Installation is done No I will restart my computer later System must be restart then complete the installation 38 Fabl Tech Corporation VVatchdog Timer This section describes how to use the Watchdog Timer including disabled enabled and trigger functions The FX5401 is equipped with a programmable time out period watchdog timer You can use yourown program to enable the watchdog timer Once you have enabled the watchdog timer the program should triggerthe I O every time before the timer times out If your program failsto trigger or disable this timer before it times out e g because of a system hang up it will generate a reset signal to reset the system The time out period can be programmed to be set from 1 to 255 seconds or minutes Time Base ADD A0 A15 Watchdog Register Counter Date D D7 1 SEK Watchdog j LED RESET The CD ROM includesa
14. OS Setup to HALTON ALL BUT KEYBO ARD This will cause the BIOS to ignore the missing keyboard and continue the boot procedure 44 FablATech Corporation MEMORY ADDRESS ERROR When the memory address indicates error You can use thislocation along with the memory map for your system to find and replace the bad memory chips MEMORY SIZE HAS CHANGED Memory hasbeen added orremoved since last boot In EISA mode use Configuration Utility to re configure the memory configuration In ISA mode enter BIO S Setup and enterthe new memory size in the memory fields MEMORY VERIFYING ERROR It indicates an error verifying a value is already written to memory Use the location along with your system s memory map to locate the bad chip OFFENDING ADDRESS MISSING This message is used in connection with the VO CHANNEL CHECK and RAM PARITY ERROR messages when the segment that hascaused the problem cannot be isolated REBOOTERROR When this emoroccursthat requires you to reboot Press any key and the system will reboot SYSTEM HALTED Indicatesthe present boot attempt hasbeen aborted and the system must be rebooted Pressand hold down the CTRL and ALTkeys and press DEL 45 FablATech Corporation 46 FablATech Corporation Appendix Dimensio
15. VGA controller Each FX5401 hastwo portsfori O communications Two RS 232C ports are available The Fx5401 is perfect for POS and POI applications Intemet Router VPN Gateway fire wall Mail Server WBT Thin Client and small Embedded Control The unit isonly 200mm L X 130mm W X 44mm H offering unparalleled performance in a very small footprint FablATech Corporation Series Comparison Table Modl e F4 99 GX1 300Mhz CS5530A 150 DIMM Max SDRAM 128MB Standard 256MB 512MB Option RTVGA Watchdog Timer Multi I O Two RS232 200 L x 130 W X 44 H FablATech Corporation Layout h ui D st t O O 101012 o I S n n A IDF 10 10 IN D FablATech Corporation Specifications a Processor Board FB2530 inside 300 MHz low power Pentium CPU with 128M B SDRAM u I O Outets Dual 100M 10M Ethemet with RJ 45 ports One parallel port with DB25 port Two Serials RS 232 with DB9 ports PS 2 compatible keyboard and mouse interface Audio function supports Line In Line Out and MIC In connector Two USB ports One Line In and One Line Out ear jet connectors One DC In plug connector One Push bottom reset switch One powerLED and hard disk Compact n Flash access LED a Storage Bay One Compact Flash slot with plug in aperture and cover one 44 pin DiskO nModule space One 2 5 hard
16. Watch Dog demo file In the file there are 3 execution programs written in different forms The sub directories of the file are 1 WATCHDOG ASSEMBLE Library and Test Program written in Assembly Language 2 WATCHDOG TURBOC Library and Test Program written in Turbo C The WATCHDOG includes a demonstration program established for users who would like to configure the Watchdog timerby themselves Note In the WATCHDOG directory README TXT file isincluded to provide demo program information 39 FablATech Corporation Watc hdog Timer Setting The watchdog timerisa circuit that may be used from your program software to detect system crashesorhang ups LED1 on this CPU board isthe watchdog timer indicator which is located at the upper left comer above the USB connector Wheneverthe watchdog timeris enabled the LED will blink to indicate that the timeris counting The watchdog timeris automatically disabled after reset Once you have enabled the watchdog timer your program must triggerthe watchdog timer every time before it times out After you triggerthe watchdog timer it will be set to non zero value to watchdog counterand start to count down again If your program failsto triggerthe watchdog timer before time out it will generate a reset pulse to reset the system The factorof the watchdog timertime out constant isapproximately 1 seconds The period forthe watchdog timertime out is between 1 to FF timerfac
17. a secondary so you have the ability to install up to four separate hard disks PIO means Programmed Input Output Rather than have the BIOS issue a series of commands to affect a transfer to or from the disk drive PIO allows the BIOS to tell the controller what it wants and then let the controller and the CPU perfom the complete task by them This is simpler and more efficient and faster Your system supports five modes numbered from 0 to 4 which primarily differ in timing When Auto is selected the BIOS will select the best available mode OnBoard FDC This field enablesthe floppy drive controller on the FX5401 Available Options Auto Disabled Enabled Default setting Auto 32 FablATech Corporation OnBoard Serial Port 1 These fields select the VO port addressforeach Serial port Available Options Disabled 3F8H IRQ4 2F8H IRQ 3 3E8H IRO 4 2E8H IRQ 3 Default setting 3F8H IRO 4 OnBoard Serial Port 2 These fields select the I O port address for each Serial port Available Options Disabled 3F8H IRQ 4 2F8H IRO 3 3E8H IRQ 4 2E8H IRO 3 Default setting 2F8H IRQ3 UARTMode Select The second serial port offersthese infrared interface modes Available Options Normal IrDA and ASKIR Default setting Normal OnBoard Parallel Port 1 This field selectsthe VO port address for parallel port Available Options Disabled 378H IRO 7 278H IRQ 5 3BC H IRO 7 Default setting 378H IRQ7 Parallel Port Mode This field specifiesthe p
18. arallel port mode ECP and EPP are both bi directional data transfer schemesthat adhere to the IEEE P1284 specifications Available Options Printer EPP1 7 SPP EPP1 7 ECP EPP1 9 EPP and ECP Default setting Printer ECP Mode Use DMA This field is read only and cannot be configured Available Options 0 1 and 3 Default setting EC P for DMA3 33 FablATech Corporation Build In CPU Audio This field specifies the intemal Audio Control Available Options Disable Enable Default setting Enable Audio Base I O Address These fields select the I O port address for Audio Available Options 2204 240H 260H and 280H Default setting 220H Audio IRQ Select This field specifies the IRQ forthe Audio Available Options Disable 5 7 and 10 Default setting 5 Audio Low DMA Select This field specifies the DMA for intemal Audio Control Available Options Disable 0 1 and 3 Default setting 1 Audio High DMA Select This field specifies the DMA for intemal Audio Control Available Options Disable 5 6 and 7 Default setting 5 34 Fabl Tech Corporation Password Setup There are two security passwords Supervisor and User Supervisor isa privileged person that can change the User password from the BIOS According to the default setting both access passwordsare not set up and are only valid after you set the password from the BIOS To set the password please complete the following steps 1 2 Select Change Super
19. blATech Corporation Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 This signal may become active during data entry when the printer is off line during printing or when the print head ischanging position orin an emor state When Bit 7 isactive the printer is busy and cannot accept data This bit representsthe current state of the printer sACK signal A 0 meansthe printer hasreceived the characterand isready to accept another Normally this signal will be active for approximately 5 microseconds before receiving a BUSY message stops A lmeansthe printerhasdetected the end of the paper A 1 meansthe printer is selected A 0 meansthe printer hasencountered an emor condition Printer Control Latch amp Printer Control Swapper The system microprocessorcan read the contents of the printer control latch by reading the address of printer control swapper Bit definitions are asfollows 7 6 5 4 3 2 1 0 X X L STROBE AUTO FD XT INIT SLDC IN IRQ ENABLE DIR write only NOTE X represents not used 59 FablATech Corporation Bit 5 Direction control bit When logic 1 the output buffers in the parallel port are disabled allowing data driven from extemal sourcesto be read when logic 0 they work asa printer port This bit is write only Bit 4 A lin this position allows an interrupt to occurwhen ACK changes from low
20. completely Window 98 and required driversto the Hard drive execute this step on the normal PC noton the FX5401 system Install the Hard drive to the FX5401 system Execute the installation procedure of VVin98 Setup 4 The rest steps please follow the Win 98 installation guide 5 The method of driver installation please referto the contents of installed drive VGA Drivers WIN98 WIN95 Driver 1 To install the VGA driver insert the CD ROM into the CD ROM device and enter DRIVER gt VGA gt NS5530 gt WIN98 If your system isnot equipped with a CD ROM device copy the VGA driver from the CD ROM to a 1 44 diskette 2 Execute CYRIXM 1 exe file The screen shows the SETUP type Press any key to enterthe main menu Asthe setup is completed the system will generate the message as follows Yes want to restart my computer now Installation is done No I will restart my computer later System must be restart then complete the installation 5 In the WINDOWS98 ME you can find the DISPLAYL icon located in the 37 Fabl Tech Corporation 6 CONTROL PANEL group Adjust the Resolution and Color LAN Utility amp Driver 1 2 To install the LAN utility OR driver insert the CD ROM into the CD ROM device and enter DRIVER gt LAN gt RTL8139C If your system is not equipped with a CD ROM device copy the LAN VGA driver from the CD ROM to a 1 44 diskette Execute insta ll exe file Note In the
21. d drive type If you use older hard disk drives which do not support this feature then you must configure the hard disk drive in the standard method asdescribed above by the USER option Video This option selects the type of adapter used for the primary system monitor that must match your video display card and monitor Although secondary monitors are supported you do not have to selectthe type in Setup You have two waysto boot up the system When VGA set as primary and monochrome set as secondary the selection of the video type is VGA Mode When monochrome set as primary and VGA set assecondary the selection of the video type is Monochrome Mode Enor Halt This option determines whether the computer will stop if an emor is detected during powerup No enors e system boot will not be stopped forany emorthat may be detected Allerors Wheneverthe BIOS detect a non fatal erorthe system will be stopped and you will be prompted All But The system boot will not stop fora keyboard enor it will stop for all Keyboard Dthererrors All But Diskette The system boot will not stop fora disk error it will stop forall other errors All But Disk Keyjthe system boot will not stop fora keyboard or disk enor it will stop for all other errors Memory This option is display only which is determined by POST Power On Self Test of the BIOS Base Memory The POST of the BIOS will determine the amount of bas
22. e 33 3 X Reserved PS 2 Mousel Coprocessor Hard Diski Reserved Quit tl Select Item Help FPU PO Modify Old values Qhiftaira Color Load BIOS Defaults Load Setup Defaults Power Management The field determines how much power consumption is needed forthe system after selecting the below items Doze Mode This field defines the continuous idle time before the system enters Doze Mode Standby Mode This field defines the continuous idle time before the system enters Standby Mode If any item defined isenabled amp active Standby timer will be reloaded HDD Power Down This field specifiesthe power conserving state that the hard disk drive enters after the specified period of hard drive inactivity has expired Available Options Disabled Standby Suspend Default setting Disa bled Modem Use IRQ This field specifies the IRQ of the modem 28 FablATech Corporation IRQ These options enable event monitoring When the computeris in a powersaving mode activity on the named interrupt request line is monitored by BIOS When any activity occurs the computer enters Full On mode 29 FablATech Corporation PCI Plug and Play ROM PCI ISA BIOS C2A434F19 PMNP PCT CONFIGURATION AWARD SOFTWARE INC PNP OS Installed No PCI IRO Actived By Level Resources Controlled By Manual Reset Configuration Data Disabled Used MEM base addr NAA TRO 3 assigned Legacy ISA assigned Legacy
23. e or conventional memory 19 FablATech Corporation installed in the system The value of the base memory is typically 512K for systems with 512K memories installed on the motherboard or 640K for systems with 640K or more memory installed on the motherboard Extended Memory The BIOS determines how much extended memory is present during the POST This is the amount of memory located above 1MB in the CPU s memory address map Other Memory This refers to the memory located in the 640K to 1024K address space Thisis memory that can be used for different applications DOS usesthis area to load device drivers to keep asmuch base memory free forapplication programs Most use forthis area is Shadow RAM Total Memory System total memory is the sum of basic memory extended memory and other memory 20 FablATech Corporation BIOS Features Setup This section describesthe configuration entriesthat allow you to improve your system performance orlet you set up some system features according to your preference Some entries here are required by the CPU board sdesign to remain in their default settings ROH PCT ISA BIOS C280434F Jf BIOS FEATURES SETUP AWARD SOFTWARE IHC Uirus Warning Disabled Video BIOS Shadow CPU Internal Cache Enabled CS000 CBFFF Shadow Quick Power On Self Test Enabled CEOOO CFFFF Shadow Boot Sequence CA SESI DOOOO D3FFF Shadow Swap Floppy Drive Disabled D4000 D7FFF Shadow Boot Up Floppy Seek Enabled DZ000
24. e setting ison aftera boot the Num Lock light is lit and user can use the number key Available options On Off Default setting On 22 FablATech Corporation Gate A20 Option This item is chosen as Normal the A20 signal is controlled by keyboard controller orchipset hardware The selection is Fast Port 92 ora chipset specific method controls meansthe A20 signal Available options Normal Fast Default setting Normal Typematic rate Setting This function specifiesthe keystroke repeat rate when a key is pressed and held down Available options Disable Enable Default setting Disa ble Typematic Rate Chars Sec Typematic Rate setsthe rate at which characterson the screen repeat when a key is pressed and held down Available options 6 8 10 12 15 20 24 or 30 charactersper second Default setting 6 Typematic Delay Msec The number selected indicatesthe time period between two identical characters appearing on screen Available options 250 500 750 and 1000 Default setting 250 Security Option This field enables password checking every time the computer is powered on or every time the BIOS Setup is executed If Alwaysis chosen a user password prompt appearsevery time and the BIO S Setup Program executes and the computer is tumed on If Setup is chosen the password prompt appears if the BIOS executed Available options Setup Always Default setting Setup 23 FablATech Corporation PCI VGA Pal
25. ette Snoop This option must be set to Enabled if any ISA adaptercard installed in the computer requires VGA palette snooping Available options Enable Disable Default setting Disa ble OS Select for DRAM gt 64MB This segment is specifically created forOS 2 when DRAM islarge than 64MB if you operating system is OS 2 and DRAM used is large 64MB You have to select OS 2 OTHERWISE under non OS 2 default isNON OS 2 Available options Non OS 2 OS 2 Default setting Non O S 2 Report No FDD for Win95 This option allows Windows 95 to share IRQ6 assigned to a floppy disk drive with other peripherals in case the driverdoesnot exist Available options Enable Disable Default setting Disa ble Video 16k Shadow C000 DC 00 16k shadow These fields control the location of the contents of the 16KB of ROM beginning at the specified memory location If no adapter ROM isusing the named ROM area this area is made available to the local bus The settings are 1 Disabled The video ROM isnot copied to RAM The contents of the video ROM cannot be read from or written to cache memory 2 Enabled The contents of C000h CFFFF are written to the same address in system memory RAM forfaster execution Available options Disabled Enabled Default setting Disable Video shadow isEnable 24 FablATech Corporation Chipset Features Setup This section describesthe configuration of the board schipset features ROM PC
26. he two DMA devices thereby maintaining IBM PC AT compatibility The following isthe system information of DMA channels DMA Controller 1 DMA Controller 2 Channel 0 Spare Channel 4 Cascade for controller 1 Channel 1 Reserved for Channel 5 Spare IBM SDLC Channel 2 Diskette Channel 6 Spare adapter Channel 3 Spare Channel 7 Spare 53 FablATech Corporation Serial Ports The ACEs Asynchronous Communication Elements ACEL to ACE2 are used to convert parallel data to a serial format on the transmit side and convert serial data to parallel on the receiverside The serial format in orderof transmission and reception isa start bit followed by five to eight data bits a parity bit if programmed and one one and half five bit format only ortwo stop bits The ACEsare capable of handling divisors of 1 to 65535 and produce a 16xclock for driving the intemal transmitter logic Provisions are also included to use this 16x clock to drive the receiver logic Also included in the ACEa completed MODEM control capability and a processor intemupt system that may be software tailored to the computing time required to handle the communications link The following table isa summary of each ACE accessible register DLAB 0 Basi intemuptenable Base 2 Interupt identification read only X Bae 3 lnecontol Line sta tus X Basss Unesatus x MODEM status X Base 7 Scratched register Divisor latch
27. lATech Corporation Chapter 2 Hardware Installation This chapter introduces the system connectors amp jumper settings and guides you to apply them forfield application Before Installation Before you install the system make sure you follow the following descriptions l Before removing the cover shut down the operation System and disconnect power switch to off and unplug AC to DC Adaptercable 2 Installorunplug any connector Compact Flash and hard disk be sure that the poweris disconnected or power switch to off from the system If not this may damage the system 3 The ESD Electricity Static Discharge may be created from human body that touchesthe board It may do damage to the board circuit FablATech Corporation o Removing Covers Installing HDD or Compact Hash If you are installing hardware option you can remove the top coverorleft side cover The following figure will guide you how to install 2 5 HDD inside the FX5401 and how to install the FX5401 fixers e D Note Tighten the screws when handling the hard diskand Compact Flash modules If you are only installing Compact Flash modules you don t need to remove top cover The following figure will guide you select P open orclose are all use to select Masteror Save device on IDE SM Compact Flash FablATech Corporation If you are installing hard disk you need to remove top cover The following figure will guide inserting
28. lists the I O port addresses used on the Industrial CPU Card OC Oh ODFh DMA Controller 2 OFOh ClearMath Coprocessor Busy Signal OFlh Reset Math Coprocessor 1FOh 1F7h IDE Interface Serial Port 4 COM4 Parallel Port 1 LPT1 EGA adapter CGA adapter 3E8h 3EFh Serial Port 3 COM3 3F0h 3F7h Floppy Disk Controller 3F8h 3FFh Serial Port 1 COM1 51 FablATech Corporation Interrupt Request Lines IRQ There are a total of 15 IRQ lines available on the Industrial CPU Card Peripheral devices use interupt request lines to notify CPU for the service required The following table showsthe IRQ used by the deviceson the Industrial CPU Card System Timer O utput Intemupt Cascade Serial Port 1 Ra noe so IRQ RQ7 Reserved LAN 1 LAN 2 PS2 Mouse FPU IRQ 14 Primary IDE USB 52 FablATech Corporation DMA Channel Map The equivalent of two 8237A DMA controllers are implemented in the FX5401 board Each controllerisa four channel DMA device that will generate the memory addresses and control signals necessary to transfer information directly between a peripheral device and memory Thisallows high speeding information transfer with less CPU intervention The two DMA controllers are intemally cascaded to provide four DMA channels for transfers to 8 bit peripherals DMA1 and three channels for transfersto 16 bit peripherals DMA2 DMA2 channel 0 providesthe cascade interconnection between t
29. ller Select Enabled if a USB device is installed to the system If Disabled are selected the system will not be able to use a USB device Available Options Disabled Enabled Default setting Enabled USB Legacy Support Select Enabled if you system containsa USB controllerand you have USB keyboard and mouse If Disabled are selected the system will not be able to use a USB device under DOS Available Options Disabled Enabled Default setting Disa ble Video Memory This field specifies which VGA display memory You can select either Video memory on the VGA The setting share onboard memory Available Options 1 5MB 2 5MB and 4MB Default setting 1 5MB Display state This field specifies which VGA display will be used when the system isboot You can select eitherthe LCD orthe CRTbooting on the VGA Available Options Both LC D and CRT Default setting CRT 26 FablATech Corporation Hat Panel Resolution When use the LCD the field specifies which select display resolution for different TFT LCD display type Available Options 640x480 800x600 and 1024x768 Default setting 640X480 27 FablATech Corporation Power Management ROM PCI ISA BIOS CzA434F19 POWER MANAGEMENT SETUF ANARO SOFTWARE IMC Power Management Disabled KeyBoard COM 22 t PM Timers t Doze Mode Disabled Standby Mode Disabled HDD Power Down Disabled MODEM Use TRO MA TRO Rediri Reserved Throttle Duty Cycl
30. lock The DB9 COM 1 2 is standard serials port connector The following tables show the signal connections of these connectors RS 232 Signal DCD2 DSR2 RXD2 RTS2 TXD2 RI2 Ui 0 0 Uu 1 NIo Q Ground Case Case Ground 10 FablATech Corporation The printer is standard DB25 connector m 13 oo STROBE AUTO FORM FEED DATA 0 ERROR 25 14 DATA 1 INITIALIZE 4 DATA2 17 PRINTERSELECTIN PRI NT 6 DAA4 19 Ground 8 Dams 21 Grund 9 bDAm7 22 Grund BUSY 13 PRINTER SELECT NoUsed m Connecting the LAN ports and USB Ports The RJ 45 connector with 2 LED s for LAN The left side LED orange indicates data is being accessed and the right side LED green indicateson line status On indicates on line and off indicates off line RJ 45 connector i The following liststhe pin assignment of RJ 45 LANI LAN2 Signal LANI LAN2 Signal E m Front View 2 mx 6 mR LAN 4 eo 8 BO C LI Li H cI 11 FablATech Corporation The Fx5401 supports a dual port USB connector Any USB device can be attached to USB ports with plug and play supported The up side port is USB 1 and the down side port is USB 2 USB 2 4 5 8 USBZL 72 Signal USBAJA2 Signal Pin 1 USBVO Pin5 USBV1 Pin 2 USBDO Pin6 USBD1 Pin 3 USBDO Pin7 USBD1 U S B Pi
31. mply write a OOH to the watchdog register tinclude stdio H tinclude WDLIB H main 1 InitWD equWd UnitS printf Disable Watch Dog Disable watch dog DisWD WD TIME 42 FablATech Corporation Chapter5 Error Coding This section outlines the emors that may occur when you operate the system and also gives you the suggestionson solving the problems Topic include e Trouble Shooting for Post Beep amp Eror Messages Trouble Shooting for Post Beep and Error Messages The following information informs the Post Beep amp erormessages Please adjust your systems according to the messages below Make sure all the components and connectorsare in proper position and firmly attached If the errors still exist please contact with your distributor for maintenance POST BEEP Curently there are two kinds of beep codesin BIOS setup e One indicatesthata video erorhasoccured and the BIOS cannot initialize the video screen to display any additional information Thisbeep code consists of a single long beep followed by three short beeps e The other indicates that an enorhasoccuned in your DRAM Thisbeep code consists of a constant single long beep CMOS BATIERY FAILURE When the CMOS battery is out of work or has run out the user hasto replace it with a new battery 43 FablATech Corporation CMOS CHEC KSUM ERROR This enor informsthat the CMOShasconupted When the battery runs weak this situation might happen
32. n E ELI C a I 004 TO Li TI m om mn i E a SS 8 gt c M UI co S NI La M Ini e NU 5 I N R45 a a Lo R o n JE FN R23 j ffi HOY d V SP K 44 2 200 i 6 fj E 47 FablATech Corporation Technical Reference Physical and Environmental DC Inputs 24V 0 8A Minimal Temperature Operating 0 C 45 C Relative humidity 5 to 95 96non condensing DC AC adapter Input AC Voltage Range 100V 240V 1A 50Hz 60Hz Output DC Voltage 24V 1 25A Maximal Real Time Clock and Non Volatile RAM The FX5401 containsa real time clock compartment that maintains the date and time in addition to storing configuration information about the computer system It contains 14 bytes of clock and control registers and 114 bytes of general purpose RAM Because of the use of CMOS technology it consumes very little powerand can be maintained forlong periods of time using an intemal Lithium battery The contents of each byte in the CMOSRAM are listed below 0 0 Seconds Second alarm Minutes Minute alarm Hours Hour alarm Date of month Month Year Status register A Status register B og 0 Dayotwek ow pa E ER 08 Sta tus register C 48 FablATech Corporation Status register D Diagnostic statusbyte Fixed disk type byte drive C Fixed disk type byte drive D 11 12 Reserved Low base memory byte High base memory byte Low expansion memory byte a8 High expansion mem
33. n 4 USBG 0 Pin8 USBG 1 m System Reset header and Power HDD LED The Fx5401 hasa push bottom switcher for system reset Push and release the bottom will cause hardware reset of FX5401 and restart system booting RESET m WE The Power Watchdog and HDD LED hastwo distinctive status Off for inactive operation and blinking light for activity POWER HD Hard Disk Access LED Red Power LED Green amp Front View Watchdog LED NL 12 FablATech Corporation O Connecting the DC Power ack and Power Switch Powerissupplied through an extemal AC DC poweradapter Check the technical specification section for information about AC DC power input voltage DC 24V 25 tolerance o 10 0 8A minimum Since the switch doesinclude a powerswitch plugging its poweradapterinto a power outlet then switch powerto on 1 when you final installed system hardware device O Power Off 1 PowerOn PED m Connecting the Audio Microphone In Speak Out Line In Left Side Line Out Right Side LINE IN pe LINE OUT SPK OUT HY 2 3 13 FablATech Corporation 14 Fabl Tech Corporation Chapter 3 BIOS Setup This chapterdescribesthe BIOS setup Overvievv BIOS are a program located on a Flash memory chip on a circuit board It isused to initialize and set up the VO peripheralsand interface cardsofthe system which includestime date hard disk drive the ISA busand connected de
34. ory byte 32 Date century byte Information flags set during poweron 34 7F Reserved for system BIOS 49 FablATech Corporation CMOSRAM Register 00h 10h 11h 13h 14h 15h 17h 18h 19h 2Dh 2Fh 30h Register 15h i 19h 2Dh II 31h 32h 33h 34h 35h 36h 37h 3Dh 3Eh 3Fh Map Standard AT compatible RTC and Status and Status Register data definitions Vanes Equipment Bits Bits Bits Number of Floppy Drives 1 Drive 2 Drives Monitor Type Not CGA or MDA 01 40x25 CGA 2 Drives 80x25 CGA Display Enabled Disabled Enabled Keyboard Enabled Not CGA or MDA 01 40x25 CGA 2 Drives 80x25 CGA Math Coprocessor Installed Absent Present Floppy Drive Installed Disabled Enabled Base Memory in 1KB increments Low Byte Base Memory in 1KB increments High Byte IBM compatible memory in 1KB increments Low Byte IBM compatible memory in 1KB increments High Byte max 15 MB IBM compatible Extended Memory Low Byte POST in KB IBM compatible Extended Memory High Byte POST in KB Extended CMOSChecksum Low Byte including 34h 3Dh Extended CMOSChecksum High Byte including 34h 3Dh 50 FablATech Corporation I O Port Address Map Each peripheral device in the system isassigned a set of I O port addresses which also becomes the identity of the device There isa total of 1K port address space available The following table
35. r Setting essesssssesessseseseeeee enne ea nene a ee KK RA ena en 40 Watchdog Timer Enabled AAA 41 Watchdog Timer Moger iriiria ana n s eee nnne ntn eee eee sere tnnt nnns 41 Watchdog Timer Disabled AAA 42 Chapter5 Eror Coding 43 Trouble Shooting for Post Beep and Emor Messages sese 43 Do 47 Bun E ln RET 47 TECHNIC al RE tere mE Qani ua tee dt O 48 Physic al and Environmental essent nnne nnne entrent 48 Real Time Clock and Non Volatile RAM uee nan eee eee eee eee eee een 48 CMOS RAM Ma p t v sh esee ERE e te t 50 VO PortAddressMap ede teen rode ve oden sht n 51 Interrupt Request Lines ORO aaa aaa enne 52 DMA Channel Ma pages n n ksi in t chen Pee eee e pena ec Rer e kx e RR dt k 53 DMA Controller Zani mette tine eter De t Rn re dd 53 SUE 54 Parallel Ports etie dr dd de ng AEN 58 FablATech Corporation Chapter lintroducing the FX5401System Overview The FX5401 isa 1U embedded system with 3 5 low power Pentium CPU module inside This user s manual provides information on the physical features installation and BIOS setup of the FX5401 Built to unlea sh the total potential of the Pentium Processor Able to support 300 MHz CPUs this system supports dual 10 100M interface network port audio 1 So DIMM socket forup to 256MB PC 100 SDRAM and a 4MB PCI
36. s and software that are not explained in this manual please contact our service engineer for service or send email to supportefa biatech com Retuming Your Board For Service amp Technical Support If your board requires servicing contact the dealer from whom you purchased the product for service information You can help assure efficient servicing of your product by following these guidelines u A list of your name address telephone facsimile number or email address where you may be reached during the day Q Description of you peripheral attachments u Description of your software operating system version application software etc and BIOS configuration u Description of the symptoms Extract wording any message For updated BIOS drivers manuals or product information please visit usat www fabiatech com Table ofContents FX5401 Embedded Computers nn nenen nonen nen nene nte nse PESE PERSE PESE ESSE SAE RSS n nasa ESSE E A ask i Small System User s Manual ssssssunseunnnnnnnnnnnnnnnnnnnnunnnnnnnnnnnnnnnnnnnnnnn nunn nnnnnnnnn nnmnnn nnmnnn nnmnnn nnan nnna i Chapter 1 Introducing the FX5401 System nnnnna anon anon sen o enen nenen nenen nn nenen neser se te nese nenen nente nese 1 OVEWIEW a eege AP AP AN ee eee rg eae 1 Series Comparison Table sinirika e aaa aaa eter ee t n eee 2 Ee D dunia 3 Specie aton S sai wn a u det do AA AAA 4 Packing Lisha aa A Pa AAA En area
37. t Select Item F10 Save 8 Exit Setup Shift F2 Change Color BIOS Functions On the menu you can perform the following functions 1 Standard CMOSSetup BIOS Features Setup Chipset Features Setup Advanced Chipset Setup PowerManagement Setup 3 4 5 6 PNP PCI Configuration 7 Load BIOS Defaults 8 Load Setup Default 9 User Password IDEAuto Detect Save amp Exit Setup Exit Without Saving 16 Integrated Peripherals Setup FablATech Corporation Keyboard Convention On the BIOS the following keyscan be used to operate and manage the menu Function ESE To exit the current menu or message Page Up Page Down To select a parameter F10 Save and exit F2 To change the colorof the menu display F2 isto go forward and F3 isto go backward UP Down Amow Keys To go upward or downward to the desired item 17 FablATech Corporation Standard CMOS Setup This section describes basic system hardware configuration system clock setup and erorhandling If the CPU board isalready installed in a working system you will not need to select thisoption anymore ROM PELZISA BIOS C2AG39F JA STAHDARN CHOS SETUP AWARD SOFTWARE IWC Date Con dd oni Fri Jan 4 2002 Time hhzmm ss 16 Go 52 HARD DISKS TYPE SIZE CVLS HEAD PRECOMP LANDZ SECTOR MODE Primary Master H 0 0 n n n 0 AUTO Primary Slave H 0 0 0 0 0 0 AUTO Drive fl 1 44H 3 5 in Drive B Hone
38. the hard disk before you must verify the pin behind the pivot end ofthe hard disk in the IDE2 HDD Note Use caution when handling the hard disk to prevent damage to IDE2 connectoras you insert hard disk Gently slide the hard disk into the IDE2 and stop when you feel resistance O Connecting the Monitor Keyboard Mouse To connectorthe peripheral control devices and monitorto the FX5401 referto the following procedure Connectorthe monitor keyboard and mouse to the FX5401 using the connections provided on the rearofthe chassis See following figure and rear pictures Compact flash N SWITCH Parallel USB KB MOUSE LAN1 LAN2 COM2 E E S E J T N DC IN 24V COM CRT POWER LED RESET HD LEG FablATech Corporation 1 A VGA connectoris provided for CRTdisplay DB15 Signal Ek te 2 Green 3 Blue CRT T ee 14 Vsync 12 DDC Data 5 DDC Clock 5 amp 10 Digital Ground LI 6 7 8 Analog Ground Others Not Used 2 The connector use the included adaptercable you can attach standard PS 2 type keyboard and mouse Standard PS 2 keyboard can be plugged into this connector without any adapter cable If PS 2 keyboard and mouse will be used simultaneously a Y type 3 terminal adapter cable is needed Mouse Data Keyboard Data Ground VCC KB MOUSE Mouse Clock E m LLLLLLIIITj O Connecting the COM ports and Parallel Port Keyboard C
39. tors If you vvant to reset your system when watchdog times out the following table listed the relation of timerfactors between time out periods DEES Time Out Period Time Out Period ime Factor n Seconds Minutes 40 FablATech Corporation Watc hdog Timer Enabled To enable the watchdog timer you have to output a byte of timer factor to the watchdog The following isa Turbo C program which demonstrates how to enable the watchdog timerand set the time out period at 6 seconds include stdio H include VVDLIB H maint d Char WD_TIME 0x6 InitWD equWdUnitS printf Enable watchdog Trigger watchdog Timer Output is 6 seconds EnWD WD TIME Watchdog Timer Tigger After you enable the watchdog timer your program must write the same factoras enabling to the watchdog register at least once every time out period to its previous setting You can change the time out period by writing another timer factorto the watchdog register at any time and you must triggerthe watchdog before the new time out period in the next trigger Below isa Turbo C program which demonstrates how to trigger the watchdog timer include stdio H include VVDLIB H main char WD_TIME 0x6 InitWD equWdUnitS printf Enable watchdog Trigger watchdog Timer Output is 6 seconds EnWD WD TIM E 41 FablATech Corporation Watchdog Timer Disabled To disable the watchdog timer si
40. upt DMA such asIRQ4 IRQ3 for serial port land 2 2 PCI ISA PnP Devicescompliant with Plug and play standard whether designed for PCI or ISA bus Use MEM base addr Resources Controlled By Auto Manual Select a base addressforthe memory area used by any peripheral that requires high memory Available Options N A C800 CC 00 D000 D400 D800 and DC O0 Default setting N A 31 FablATech Corporation Peripheral Setup This section describesthe function of peripheral features ROM POLFISA BIOS C2AS34F Jf INTEGRATED PERIPHERALS AWARD SOFTWARE THC IDE HDD Block Mode Enabled Primary IDE Channel Enabled Build in CPU Audio Master Drive PIO Mode Auto udio IZO Base Address Slave Drive PIO Mode Auto MPU 401 I U Base Address udio IRQ Select IDE Primary Master UDHA Auto udio Low DHA Select IDE Primary Slave UDMA Auto Budo High DHA Select Onboard FOC Controller Enabled Onboard Serial Port 1 3F8 IRQ Onboard Serial Port 2 UART Mode Select Onboard Parallel Port Parallel Port Mode ECP Mode Use DHA IDE HDD Block Mode This option allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive HDD IDE PIO IDE hard drive controllers can support up to two separate hard drives These drives have a master slave relationship which is determined by the cabling configuration used to attach them to the controller Your system supports one IDE controller a primary and
41. vicessuch as the video display diskette drive and the keyboard This program will not be lost when you tum off the system The BIOS providesa menu driven interface to the console subsystem The console subsystem contains special software called firmware that interacts directly with the hardware componentsand facilitates interaction between the system hardware and the operating system The BIOS default values ensure that the system will function at its normal capability In the worst situation the user may have conupted the original settings set by the manufacturer All the changes you make will be saved in the system RAM and will not be lost after power off When you start the system the BIOS will perform a self diagnosticstest called Power On Self Test POST forall the attached devices accessories and the system Press the Del key to enterthe BIOS Setup program and then the main menu will Show on the screen Note Change the parameters when you fully understand theirfunctions and subsequence 15 Fabl Tech Corporation ROM PCI ISA BIOS 2A434F JD CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CHOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP PNPAPCI CONFIGURATION LOAD BIOS DEFAULTS INTEGRATED PERIPHERALS SUPERVISOR PASSWORD USER PASSWORD IDE HDD AUTO DETECTION SAVE amp EXIT SETUP EXIT WITHOUT SAVING LOAD SETUP DEFAULTS Esc Qui
42. visor Password Type the desired password up to 8 character length when you see the message Enter New Supervisor Password Then you cango onto seta user password up to 8 character length if required Note that you cannot configure the User password until the Supervisor password isset up Enter Advanced CMOSSetup screen and point to the Password Checkup field Select Always or Setup Always a visitor who attempts to enter BIOS or operating system will be prompted for password Setup a visitor who attemptsto the operating system will be prompted for user password You can enter either User password or Supervisor password Point to Save Settings and Exitand press Enter Press Y when you see the message Save Curent Settings and Exit Y N Note it issuggested that you write down the password ina safe place to avoid that password may be forgotten or missing To set the password please complete the following steps 1 2 Select Change Supervisor Password Press Enter instead of entering any character when you see the message Enter New Supervisor Password Thus you can disable the password 35 FablATech Corporation 36 FablATech Corporation Chapter 4 Software Installation The enclosed diskette includes FX5401 VGA AUDIO driver and LAN driver To install and configure you FX5401 system you need to perform the following steps Installation WIN 95 98 1 Copy
Download Pdf Manuals
Related Search