34453D SE2 Series User Guide & Setup Instructions.pmd
Contents
1. SE2 Models and Features 9 pa 1 Retaining screw 2 Pry here Bosch Security Systems 6 03 34453D Remove the retaining screw on the back of the enclosure see Figure 3 Using a flat head screwdriver pry the lower part of the front cover away from the rest of the enclosure Figure 3 Back of Transmitter SE2 Series User Guide amp Setup Instructions 2 0 Part Il Setup Instructions 2 3 Figure 4 shows the location of the specific jumper for each feature Note that the lanyard snatch jumper and lanyard switch are only included on the SE2M SE2S SN and SE2U SN models Figure 4 Internal Components Enabling Disabling Features 1 Lanyard switch 2 Man down jumper 3 Supervision jumper 4 Lanyard jumper 5 Battery compartment 2 3 1 Supervision Feature Remove the battery before moving the jumpers To enable the supervision tracking feature place its jumper in the ON position as indicated in Figure 5 Do this by moving the jumper to cover both pins using a small pair of pliers With supervision tracking enabled the transmitter sends a silent transmission to the central console approximately every 90 seconds This enables the central console to monitor the battery and transmitter condition as well as track the transmitter s location within the protected area Figure 5 Jumper Positions 1 Off 2 On 2 3 2 Man Down and Lany2. g Figure 1 SE Transmitter Qe th 3 gt 1 Test button 2 Alarm button 3 Lanyard EN 3 1 2 Using the SE2 Transmitter X This feature is enabled on this transmitter This feature is not enabled on this transmitter 1 24 Standard Operation X Transmitting a Manual Alarm To send an alarm press and hold the Alarm button for 1 second The transmitter sends an alarm signal to the central console With some SE2 models you can also visually confirm the signal if done in sight of a receiver receiver lights the red LED After a manual alarm is initiated the auto tracking feature begins The transmitter sends a signal to the central console every 15 sec updating your location To reset the transmitter after a manual alarm is initiated perform a test as described in T sting the Transmitter xX Testing the Transmitter To test your transmitter stand in sight of a siren strobe or a receiver While holding down the Test button press the Alarm button until you hear an audible tone A test transmission is sent to the central console Also the strobe on an outdoor siren strobe or the green LED on a receiver illuminates There might be a brief delay of 2 sec to 3 sec before the flashing light appears If you do not receive confirmation of a successful test transmission such as the strobe on a siren strobe or the green LED on a receiver not illuminating try the test again If there is
3. still no confirmation take the transmitter to the security department Bosch Security Systems 6 03 34453D SE2 Series User Guide amp Setup Instructions 1 0 Part User Guide 1 2 2 Optional Features Man Down Alarm Feature With the man down feature enabled the transmitter alarms whenever the transmitter you is in a prone position 60 from upright The transmitter emits an audible tone upon sensing the prone position and initiates the auto tracking feature To reset the transmitter after a man down alarm is initiated return the transmitter to the upright position and perform a test as described in Section 1 2 1 Standard Operation Lanyard Snatch Alarm Feature With the lanyard snatch alarm feature enabled the transmitter sends an alarm signal to the central console and initiates the auto tracking feature when the lanyard pin is pulled out of the unit To reset the transmitter after a lanyard snatch alarm is initiated reinsert the lanyard pin and perform a test as described in Section 1 2 1 Standard Operation 1 2 3 The transmitter comes with a clip which can be worn over a pocket or belt or be secured to a belt Secure the clip to the transmitter screws provided at the two top positions to use it as a clip Wearing the Transmitter To use the clip securely on a belt attach it at the third location at the bottom Use the screw already securing the battery door The clip is designed to wear
4. SE2 Series User Guide amp Setup Instructions EN Transmitters BOSCH SE2 Series User Guide amp Setup Instructions FCC Notice EN 2 FCC Notice This device complies with Part 15 of the FCC Rules and with RSS 210 of Industry and Science Canada Operation is subject to the following two conditions e This device may not cause harmful interference and e This device must accept any interference received including interference that may cause undesired operation FCC ID ESV 0117 1 Canada 1249 102 643 Bosch Security Systems 6 03 34453D SE2 Series User Guide amp Setup Instructions 1 0 Part User Guide 1 0 Part I User Guide For Distribution to All SE Users 11 Introduction The SE2 Series Transmitters are personal transmitters designed to work with the Security Escort system When initiated a signal identifying you and your location is sent to the Security Escort monitoring station The SE2 can also be tested within sight of a receiver or siren strobe by the user There are several SE2 models available each with optional features Check boxes are provided in this document for your security department to indicate which features are available on your transmitter The Security Escort system is not a substitute for safe behavior System users should not take personal risks under the misconception that the system provides protection that compensates for taking such risks 2
5. ard Snatch Features To enable the man down and lanyard snatch features place the desired feature jumper in the ON position as shown in Figure 5 Use a small pair of pliers to move the jumper so it covers both pins See Section 1 2 2 Optional Features for descriptions of these features 2 3 3 The transmitter uses a CR2 3 V lithium battery The central console indicates when the battery is low and needs replacement See Figure 4 for battery polarity The battery life depends on usage and enabled features Battery Bosch Security Systems 6 03 34453D SE2 Series User Guide amp Setup Instructions 2 0 Part Il Setup Instructions EN 7 Notes Bosch Security Systems 6 03 34453D Bosch Security Systems 130 Perinton Parkway Fairport NY 14450 9199 USA www boschsecurity us Customer Service 800 289 0096 Technical Support 888 886 6189 2003 Bosch Security Systems Subject to change Printed in the USA 34453D BOSCH
6. on a security type utility belt If worn on a thin belt be aware that such a loose fitting can cause the transmitter to activate the man down alarm if enabled when there is too much loose movement Figure 2 Belt Clip Attachment 1 Must use 2 Optional 3 Side view of clip 4 Clip 5 Back of transmitter Bosch Security Systems 6 03 34453D SE2 Series User Guide amp Setup Instructions 2 0 Part Il Setup Instructions 2 0 Part Il Setup Instructions For Security Department Use Only 2 1 Models and Features The various SE2 models and their features are identified in Table 2 Model Feature SE2S SE2U SE2M SE2S SN SE2U SN Man Down Supervision Tracking Lanyard Snatch Auto Tracking Silent Manual Alarm Low Battery Indication x EN is only used for system testing and does not generate a system alarm Before distributing the attached User Guide place an X in the box next to each feature enabled on the transmitter 2 2 Removing the Cover The Man Down Supervision Tracking and Lanyard Snatch features are controlled by the jumpers located next to the battery compartment To remove the cover 1 Remove the belt clip if used Table 1
Download Pdf Manuals
Related Search