Operating instructions for condenser tumble dryer T 7944 C
Contents
1. Protruding lid for holding when moving the machine see arrows Air inlet vent for cooling the condenser unit Mains connection cable Hose for external drainage of condensed water Accessories for connection to a sink drain outlet 42 Installation site This tumble dryer can be installed under a sufficiently high worktop N Make sure the dryer door can be opened without hindrance after installation The machine lid must not be removed Transporting the machine to its installation site When moving the dryer hold it by the lid where it protrudes to the rear To manoeuvre the machine out of its packing case to its installation site hold it by the front feet as well as by the edge of the lid where it protrudes to the rear of the washing machine Washer dryer stack The tumble dryer can also be combined with a Miele washing machine in a washer dryer stack The appropriate WTV stacking kit to match your dryer is required accessory available to order Stacking kits must only be installed by a suitable qualified fitter Installation and connection Levelling the machine The machine must be perfectly level to ensure safe and proper operation m The screw feet can be adjusted to compensate for any unevenness in the floor The air inlet and outlet vents on the front and back of the machine must not be covered as this would prevent sufficient ventilation for2. 0 0 0 0 50 Extending the range of the drying level for the Cottons programme 50 Extending the drying level for the Minimum iron programme 51 ANU CreaSe SCuING one scese see eaten a gw EOE head ee he ee aR 52 Altering the volume of the buzzer unuunu aaa 53 Extending the drying level for the Automatic plus programme 54 Extending the cooling downtime 0 eee 55 DIAN DY 24 crh essed eee nbieie heed baheteen beet AAEE ai a btee ad be 56 MeMOryTUNCHON ead inea area ode ae Peed beer dae beeen ae oad 58 Clean out airways indicator 6 ee eee 59 Keypad TONG ss s0in sostas shits Wa Pree eh eee Seen dwn ys EER ae ee eee 60 Adjusting the dryer s electronics for very soft water 0 00000000 e ee 61 Extending the drying level range 2 eee 62 Warning and Safety instructions It is essential to read these instructions This tumble dryer conforms to current safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the tumble dryer please read these instructions carefully before using it for the first time They contain important information on its safety installation use and maintenance Keep these instructions in a safe place and ensure that new users are familiar with the content Pass them on to any future owner Correct application gt This tumble dryer is designed
3. 0 0 00 00 eee 21 EXTA ODIOS eere caved nea aed awa RAO al ee ae R 21 LOW temperatur Gss srra r r arira EE RRES E RAER ERE E aE ei 21 BUZZO eee i E ee a e ee a a a a ee a e 21 Delay Stai neede teete ea ra e ee a ee aed Bee is 21 Programme chart 00 0 00000 eee 22 Changing the programme sequence 0 000 e eee 25 Once a programme has started 0 eee 25 changing the programme 6 6 ee 25 cancelling the programme and then selecting a different programme 25 cancelling the programme and then removing the laundry 25 Changing Delay start 2 eee 25 Adding or removing laundry after a programme has started 25 MIME TEMAINING cd atau tte nree hawk Shad ape ahha ea pe ae et 25 Electronic system lock 000 c eee 26 Contents Cleaning and care 0 00 0 cette 27 Emptying the condensed water container 0 0 0 ee 27 Cleaning the fluff filters 2 eee 28 Cleaning them whilst dry 2 0 2 0 0 28 Cleaning them with water s a sasaaa 29 Cleaning the tumble dryer 0 0 0 eee 29 Cleaning the condenser unit suasana 00000 c eee 30 Removing the condenser UNIT 4 thaw a we ra ee peed gad sey eal eo 30 Checking the condenser unit 0 0 000 00 cece eee 31 Cleaning the condenser unit naaa saaa 31 Replacing the condenser unit 00 0 ters trari harep rasake 32 Problem solving guide 2 0 ee 33 Probl
4. NA clogged filter is a fire hazard The fluff filter must be cleaned after every programme gt Remove all objects from pockets such as lighters and matches B To prevent the risk of fire the following textiles must not be dried in this tumble dryer Items which have not been washed Items such as workwear which have not been thoroughly cleaned and which are still soiled with grease oil or other desposits Such as cosmetics lotions etc If items have not been thoroughly cleaned there is a danger that these might ignite when heated even after they have been removed from the dryer at the end of the programme ltems that have been soiled with substances such as cooking oil acetone petrol kerosene spot removers turpentine waxes wax removers and other chemicals e g mops and floor cloths should be washed in hot water with extra detergent before being dried in the tumble dryer Items which have been splashed with hair lacquer hair spray nail polish remover or similar substances 10 Warning and Safety instructions When washing such heavily soiled items ensure that you use sufficient detergent and select a high temperature If in doubt wash the items several times gt Oil affected items can ignite spontaneously especially when exposed to heat sources such as in a tumble dryer The items become warm causing an oxidation reaction in the oil Oxidation creates heat If the heat cannot escape the ite
5. The Low temperature indicator light will briefly flash nine times 58 The option selected will be displayed by a number which will alternate with P Default setting Memory deactivated Memory The Automatic plus indicator light will also flash Pressing the Start Stop button switches from one to the other O Switch the dryer off The settings have been changed You can alter the settings again at any time Control m Repeat steps to O m Switch the dryer off after step Programmable functions Clean out airways indicator Fluff should be removed after drying The Clean out airways indicator will remind you to Clean the filters when a certain amount of fluff has collected in the filters You can decide at what level of fluff this reminder should be given You will have an idea of how often this should be done after a few drying programmes Follow steps 0 0 0 to programme and store in memory Before you begin first ensure that The dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps Switch the dryer on Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button eight times The Low temperature indicator light will flash on and off slowly once The option selected
6. The plug must be rendered useless and the cable cut off directly behind the appliance or the machine to prevent misuse Energy saving tips To avoid unnecessarily long drying times and high consumption of energy Make sure that your laundry is thoroughly spun before drying The higher the spin the greater the savings that can be made in energy and time during drying Load according to the optimum amount of laundry recommended for the programme being used see Programme chart Underloading is uneconomical Overloading gives a poorer quality of drying and may cause unnecessary creasing Make sure the room in which the dryer is located is well ventilated Make sure the fluff filters are clean before using the dryer Check the condenser unit from time to time and clean it when necessary Contents Caring for the environment 0 0 00 c cee eee 2 Warning and Safety instructions 0 000000 cece 6 Operating the tumble dryer 0 00 0 cee eee 15 COMUONPANEl 2 202625 ewe ne eran he teed Se btwn yess She ee AY ee 15 Notes on laundry care 0 0 17 Care SyMbOlSix sai ienga i or Shee a ee Rha ode ow REY PG SES E o e 17 TIPS ON Gr YING 2 Aas 2 ate Seve oad Wa a does ha ergo do a due Mae eae al ad ane 17 How to dry correctly 6 0 0 0 eee 18 Brief INStUClOnS sser es ncnsodiet downs peruse nme ed ears A tes 18 Extra options Delay start
7. of overflowing water which could cause damage m Use the bow shaped guide to prevent the drain hose from becoming kinked Installation conditions requiring a non return valve Certain installation conditions require the fitting of a non return valve available as an optional accessory A non return valve will prevent the risk of back flow out of the dryer which could cause damage A non return valve is required If the tumble dryer is connected to a sink drain outlet see the following section If the tumble dryer is connected to a drainage system already in use by another appliance e g a dishwasher or washing machine Example Connection to a sink drain outlet The drain hose with non return valve fitted can be connected directly to a suitable sink drain outlet m Remove the following from the back of the dryer at the top Adapter 1 and hose clip 3 behind it 45 Installation and connection 1 Adapter 2 Nut 3 Hose clip 4 End of the hose 5 Non return valve 6 Tumble dryer drain hose 46 m Fit adapter 1 to the sink drain outlet using nut 2 If this nut has a flat disc in it you should take the disc out first m Attach the end of the hose 4 to adapter 1 m Use a screwdriver to tighten hose clip 3 up close to the nut N Non return valve 5 has to be fitted with the arrow pointing in the direction of flow i e towards the sink Otherwise wat
8. You can alter the settings again at any time Control m Repeat steps to O m Switch the dryer off after step Programmable functions Extending the cooling down time The cooling down phase which takes place before the end of a programme can be lengthened if required This makes the garments easier to handle The cooling down time is only available for programmes with drying levels Follow steps 0 0 0 to programme and store in memory Before you begin first ensure that The dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps Switch the dryer on Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button five times The Low temperature indicator light will briefly flash on and off seven times The option selected will be displayed by a number which will alternate with P O Default setting The cooling down time will be five minutes longer The Automatic plus indicator light will also flash once e The cooling down time will be ten minutes longer The Automatic plus indicator light will also flash twice Pressing the Start Stop button switches from one to the other Switch the dryer off The settings have been changed You can alter the settings again at any time Contro
9. connected to the terminal which is marked with the letter N or coloured black The wire which is coloured brown must be connected to the terminal which is marked with the letter A or coloured red WARNING THIS APPLIANCE MUST BE EARTHED 47 Consumption data Load Final spin speed ina Residual Energy Duration domestic washing moisture machine kg rpm kWh min Cottons Normal 7 0 1000 60 3 80 121 Cottons Normal 7 0 1200 53 3 45 110 7 0 1400 50 3 25 105 7 0 1600 48 2 90 95 7 0 1800 43 2 85 93 Cottons Normal Low temperature 7 0 1000 60 4 10 169 Cottons Hand iron 7 0 1000 60 3 00 96 Cottons Hand iron 7 0 1200 53 2 65 85 7 0 1400 50 2 50 80 7 0 1600 48 2 10 70 7 0 1800 43 2 05 68 Minimum iron Normal 39 1200 40 ESS 44 Minimum iron Normal Low temperature 3 5 1200 40 1 40 66 Minimum iron Hand iron 3 5 1200 40 1 15 39 Automatic Normal 5 0 600 50 2 70 102 Delicates Normal 2 5 700 50 1 50 98 Denim Normal 3 0 900 60 2 30 109 Smoothing 1 0 1000 60 0 50 30 Woollens handcare 2 0 1000 50 0 11 4 1 Weight of dry laundry 2EN 61121 2005 test programme All data without a star placed against it was calculated using EN 61121 2005 Note for test institutes Results based on European Standards Before testing in accordance with EN 61121 dry a 3 kg load of cotton laundry with 70 residual moisture as per the above standard using the Cottons N
10. cooling the condenser unit The gap between the base of the dryer and the floor must not be minimised by a plinth or thick piled carpet as this will prevent a sufficient intake of cold air Room ventilation The air which is taken in when the dryer is in operation is blown out of the vents on the front of the machine and warms up the air in the room It is very important particulary if the room is small to ensure adequate ventilation Opening a window for example will allow more air to enter the room Otherwise running times and energy consumption could be increased Before moving the tumble dryer again e g when moving houses After each use a small quantity of condensed water will collect in the area around the pump This water can run out if the tumble dryer is tipped up when it is being moved It is a good idea to run the Warm air programme for approximately 1 minute before moving it Any remaining condensed water will then be fed into the condensed water container or out through the drain hose 43 Installation and connection External condensed water outlet General notes When drying is in progress condensed water is pumped into the condensed er container through the drain hose at wa the back of the dryer The condensed water can also be drained off directly if the machine is installed near a sink drain outlet etc so that the condensed water container does not have to be emptied Drain
11. message is cancelled causes and their remedies Open and close the door The Clean out while the dryer is switched airways on indicator light Start a programme comes on If this warning appears The buzzer again contact Miele sounds The Empty out The condensed water Empty out the condensed container container is full or there is a water container indicator light kink in the drain hose Check the drain hose comes on To delete the message The buzzer Open and close the door sounds while the dryer is switched on 34 Problem solving guide Problem Possible cause Remedy The indicator light The dryer is on standby See Programmable Start Stop flashes This is anormal function functions slowly and the display is dark and does not indicate a fault Some programmes won t start anymore The indicator light for that programme doesn t light up anymore either There is no immediate cause Switch the dryer off and then on again Select the programme that cannot be started If you still can t start the programme there is a fault Contact Miele The Start Stop indicator light flashes does not flash The flashing indicates that a programme can be started After the programme has started the flashing will change to a constant light 35 Problem solving guide An unsatisfactory drying result Pr
12. six times The Low temperature indicator light will briefly flash on and off eight times The option selected will be displayed by a number which will alternate with P 0 On i Factory default settings Not in current programme The Automatic plus indicator light will also flash once Z Off The Automatic plus indicator light will also flash twice Pressing the Start Stop button switches from one to the other Switch the dryer off The settings have been changed You can alter the settings again at any time Control m Repeat steps to O m Switch the dryer off after step 57 Programmable functions Memory function The electronics will memorise any Extra options selected for a programme The duration selected for the timed drying programmes will also be stored in memory These settings will be selected automatically the next time the programme is chosen You can either accept these or change them by pressing the appropriate button Follow steps 0 0 0 to programme and store in memory Before you begin first ensure that The dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps Switch the dryer on Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button seven times
13. start indicator light will light up constantly Delay start counts down in one hour steps to 72h and afterwards in minute steps until the programme starts The drum will turn briefly every hour to help prevent creasing To cancel or change Delay start m Press the Start Stop button to cancel Delay start m Press the Delay start button repeatedly until the required delay period appears in the display m Press the Start Stop button to begin Delay start Add laundry You can add laundry while Delay start is counting down m Switch the dryer off Opening the door before switching off the dryer first will cancel Delay start m Open the door and add laundry m Close the door and switch the dryer on 21 Programme chart Cottons Max load 7 kg Extra dry Normal Fabric type Single and multi layered cotton fabrics such as towels bathrobes T shirts and underwear Notes Select Extra dry for multi layered and very thick fabrics Do not use Extra dry for loopknit fabrics e g T shirts underwear as they have a tendency to shrink Low temperature Low temperature select this option for delicate fabrics with the O symbol on the care label Hand iron Machine iron Fabric type Cotton and linen fabrics for example table linen bed linen starched laundry Note To prevent laundry from drying out it should be rolled up until you are ready for ironing
14. Low temperature Low temperature select this option for delicate fabrics with the O symbol on the care label Minimum iron Max load 3 5 kg Normal Hand iron Fabric type Minimum iron items made of cotton synthetic or mixed fibre for example dresses trousers skirts or table cloths Low temperature Low temperature select this option for delicate fabrics with the O symbol on the care label Delicates Max load 2 5 kg Normal Hand iron Fabric type Delicate items made of synthetic fibres easy care cotton or blended fabrics e g shirts blouses and evening wear with sequins and beading Low temperature Low temperature cannot be deselected Weight of dry lau 22 ndry Programme chart Woollens handcare Max load 2 kg Fabric type Woollen fabrics Notes This programme only fluffs up woollen garments They are not dried completely by this programme Remove garments as soon as the programme has finished and leave to finish drying at room temperature Low temperature Low temperature cannot be deselected Express Max load 3 5 kg Extra dry Normal Hand iron Machine iron Fabric type Tougher fabrics with the care label J suitable for the Cottons programme Note Reduced programme duration Automatic plus Max load 5 kg Normal Hand iron Fabric type Mixed loads of garme
15. The Low temperature indicator light will briefly flash on and off twice The option selected will be displayed by a number which will alternate with P O The drying level will be damper I Standard setting The Automatic plus indicator light will also flash once e The drying level will be drier The Automatic plus indicator light will also flash twice Pressing the Start Stop button switches from one to the other Switch the dryer off The settings have been changed You can alter the settings again at any time Control m Repeat steps to O m Switch the dryer off after step 51 Programmable functions Anti crease setting Helps prevent creasing if laundry is not normally removed immediately after the end of a programme Anti crease is set as a standard setting You can shorten the time or switch it off completely can be used for all programmes except Woolens handcare should always be switched on Follow steps 0 0 0 to programme and store in memory Before you begin first ensure that The dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps Switch the dryer on Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button twice The Low temperature indica
16. brics Minimum iron items made of cotton synthetic or mixed fibres For example trousers anoraks shirts Notes Suitable for dry and damp laundry fabrics Smoothes out creasing caused during the spin cycle in the washing machine Remove garments as soon as the programme has finished so that they are easy to iron Low temperature Low temperature cannot be deselected Weight of dry laundry 24 Changing the programme sequence Once a programme has started changing the programme You cannot change to another programme once a programme has started this prevents unintentional alterations You will need to cancel the current programme before you can select a new one cancelling the programme and then selecting a different programme m Press the Start Stop button The items will be cooled down depending on the temperature reached and how long they have been dried for If you press the Start Stop button again during the cooling down phase Finish will appear in the display m Press the Door button m Close the door m Select and start a new programme cancelling the programme and then removing the laundry m Refer to the following Adding or removing laundry after a programme has started m Switch the dryer off after closing the door Changing Delay start m See Delay start Adding or removing laundry after a programme has started m Press the Doo
17. celling a programme once it has started The button flashes when a programme is selected and then is on constantly when the programme has started OCottons Automatic plus O Finish Normal O O Minimum iron Denim O Hand iron O Machine iron O QD ODelicates Low temperature O Cool air O o Woollens handcare Warmare O Express Gentle smoothing O 0O Low temperature button Delicate fabrics are dried at a lower temperature Drying level button Indicator lights show the selected drying level Programme selector Indicator lights show the selected programme Door button Pressing this button will open the door even when the dryer is switched off at the mains On Off button gt For switching the machine on or off Operating the tumble dryer The following information appears in the display Programme duration Programme sequence Drying Cooling down Finish Check and fault messages The following functions are selected via the display Programme duration Warm air Cool air Delay start You can delay the start of a programme Once the Delay start time has finished the programme begins automatically Programmable functions The programmable functions are used to alter the machine s electronics to suit changing requirements See Programmable functions for more details Perfect Dry indicator light The Perfect Dr
18. ck the rubber seals Use a cloth to remove any visible fluff from the inside of the condenser unit housing A programme cannot be started There is no immediate cause Is the dryer switched on Is the mains plug plugged in Is the door closed properly Has the fuse or circuit breaker tripped Power cut When power is restored to the dryer after a power cut the programme will continue as long as the cooling down phase had not been reached The interior drum lighting does not come on The lighting switches off automatically to save energy Switch the dryer off and then on again Ifthe lamp needs to be replaced follow the instructions Refer to the following 38 Problem solving guide Changing the lamp The lamp specification and Disconnect the machine from the maximum wattage are stated on the mains electricity supply data plate and on the lamp cover m Open the door m Replace the lamp You will find the interior lamp cover at m To close the cover push it upwards the top of the drum aperture and press it on the left and right until you hear it click into position Ensure that it is fitted into position securely as any moisture could cause a short circuit m Insert a Suitable tool such as a wide bladed screwdriver under the side edge of the lamp cover as illustrated m Apply alittle pressure and whilst doing so tur
19. ctions Do not use solvents abrasive cleaners glass cleaners or all purpose cleaners These could damage plastic sufaces and other parts The machine must never be hosed down m Dry all parts with a soft cloth 29 Cleaning and care Cleaning the condenser unit Detergent residue hair and fine fluff from the dryer can get through the fluff filters and block the condenser unit Dust from the room in which the dryer is installed can also get into the condenser unit and cause a blockage Check the condenser unit at least twice a year Always check it if the Clean out airways indicator light comes on If the dryer is used frequently then check the condenser unit after approx 100 drying cycles Clean it if necessary m Turn the lever on the inner cover downwards to the vertical position Removing the condenser unit m Tilt the cover forwards m Remove it by pulling it diagonally upwards m Open the service panel m Now remove the panel by pulling it diagonally upwards and place it to one side m Turn the lever on the condenser unit upwards to the vertical position 30 Cleaning and care m Pull the condenser unit out of its housing by the handle Checking the condenser unit m Hold the condenser unit up to the light as shown m Check to see if there is any fluff inside it The arrows in the illustration above indicate where to l
20. d Office Perth 205 207 Stirling Highway Claremont WA 6010 1300 4 MIELE 1300 464 353 www miele com au Miele www miele shop com Miele New Zealand Limited Miele Gallery and Head Office Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland New Zealand Telephone 0800 264 353 www miele co nz Miele Global Headquarters Germany Miele amp Cie KG Carl Miele StraBe 29 33332 G tersloh Federal Republic of Germany Alteration rights reserved 1912 CE M Nr 07 850 910 01
21. e cleaned after every programme Cleaning and care Cleaning them with water If there is a great deal of compacted fluff on any of the filters they can be removed and cleaned under hot running water m Open the door and pull the fluff filter out of the door as described previously The two filters in the door opening can also be removed if you need to clean them with water m Turn dial and pull the filter by the dial out of the door opening as shown 2 Do the same on the other side m Rinse all the filters under hot running water m Then shake the filters until no more water droplets are visible m Dry the filters thoroughly with care m Clean the area underneath these filters e g with a vacuum cleaner Do not replace them if they are damp or wet Damp or wet filters could cause operational faults m Push the large filter back into the door holder until it clicks into position Ensure it is facing the correct way m Replace the filters in the door opening by first inserting them at the bottom and then pressing them into place at the top m Lock both dials Cleaning the tumble dryer Disconnect the machine from the mains electricity supply m Clean the housing and control panel with a slightly damp cloth and a mild detergent or soapy water m The drum and other stainless steel parts can be cleaned with a suitable propietary stainless steel cleaner following the manufacturer s instru
22. e end of the drying programme If this was done remove and spread out all items quickly so that the heat is dissipated gt Fabric conditioner and similar products must be used according to the instructions on the manufacturer s packaging B The tumble dryer is not to be used if industrial chemicals have been used to clean it Warning and Safety instructions gt The dryer must not be used without the fluff filters in place or if the fluff filters are damaged in any way P gt The fluff filters must be cleaned regularly gt The dryer must not be used without the condenser unit in place B The fluff filters must be thoroughly dried after cleaning Damp or wet filters could cause operational faults gt Do not install the tumble dryer in a room where there is a risk of frost occurring At temperatures around freezing point the tumble dryer may not be able to operate properly There is a risk of damage if the condensed water is allowed to freeze in the pump hoses and or condensed water container The ambient room temperature should be between 2 C and 35 C gt If the water is drained externally through the drain hose instead of being collected in the condensed water container make sure the drain hose is securely attached if you hang it in a sink or basin to avoid the hose slipping and the water causing damage B gt Condensed water is not drinking water It can cause health problems in both people and animals B Al
23. eee Viele Operating instructions W e S3 Ugg ee uN for condenser tumble dryer T 7944 C To avoid the risk of accidents or en AU NZ damage to the appliance it is essential to read these instructions before it is installed and used for the first time M Nr 07 850 910 Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of babies and young children Danger of suffocation Rather than just throwing these materials away please ensure they are offered for recycling Disposal of your old appliance or machine Electrical and electronic appliances machines often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance or machine Therefore please do not dispose of your old machine or appliance with your household waste ys Please dispose of it at your local community waste collection recycling centre and ensure that it presents no danger to children while being stored for disposal It should be unplugged or disconnected from the mains electricity supply by a competent person
24. em Soning GUIE saser ana bya kd bead bene bbe eh eeeenae de buale bad 33 Check and fault messages in the display 0 00 00 c eee eee 33 An unsatisfactory drying result 2 0 0 eee 36 Other problems 0 2 0 eee 37 Changing the lamp 0 0 eee eee 39 After Sales service 0 00 0 40 Future updates PC 4 i200 4 yee ii eenei oD Gaya yadhehe sien oad es 40 Optional accessories eresi sa aee d a pe Sa bee ed a aoa ee A ae A 40 Installation and connection uaaa 41 POM MIGW3 2 is te 5 ees aaa i fatter aE A ip ia a e a e D i ua dt Aaa 41 Rean VIEW 4 0204 re tiekia aE aE e ab TES eed deo A ERE n ia 42 MeMO BE eti tea debate ia s e a ea a ha 42 Transporting the machine to its installation site naaa aaa aaa 42 Washer dryerstack 22 sedeat atope aieia imita yi ea da a a eE EOE ei 42 Leveling the MACHINGs 4 4 4 25 aisse eh RASS rdan k a MARE eRe ee ee 43 Room VS MULATION i sine aft wo Sinn feat ats teal Rat Se haha Ac do near eis Ag een en 43 Before moving the tumble dryer again e g when moving houses 43 External condensed water outlet 6 ee 44 Arranging the drain hose saser seyir eee 44 External drainage via a sink or gully cs 0 45 Installation conditions requiring a non return valve 6 ee 45 Electrical Connection sesir eats baie whee tad wie Mh She eee Sages 47 Contents Consumption data 0 0 00 00 eee 48 Technical data 0 eee 49 Programmable functions
25. er the other The indicator light for the Low temperature button will flash and a key symbol f o will appear in the display Release the Low temperature button The system lock is activated m Switch the dryer off Deactivating the system lock Before you begin first ensure that The dryer is switched off The door is closed m The procedure is the same as for activating the lock Repeat steps to O At step the indicator light for the Low temperature button will stop flashing and the key symbol G o will go out The electronics are no longer locked Cleaning and care Emptying the condensed water container The condensed water will be collected in the condensed water container unless the appliance has been fitted with a drain hose see Installation Empty the condensed water container after every drying programme The Empty out container indicator light will come on if the maximum level of the condensed water container is reached The indicator light will go out when the door is opened and closed again N Close the door fully Otherwise the door and the front panel of the condensed water container could suffer damage when pulling the container out m Pull out the container m Hold it at the front and towards the back and keep it in a horizontal position when carrying it m Empty the container m Replace the container in the dryer N Condensed water should no
26. er will not drain out of the machine m Fit non return valve 5 to the tumble dryer drain hose 6 making sure it is fitted in the correct direction see arrow on non return valve m Secure the non return valve using hose clips Installation and connection Electrical connection This tumble dryer is supplied ready for connection to an AC single phase supply The machine is supplied with a mains cable with moulded plug The accesibility of the plug must be always ensured in order to separate the dryer from the mains The appliance should be connected up only by a qualified electrician in accordance with national and local safety regulations For extra safety it is advisable to install a residual current device RCD with a trip current of 30 mA The voltage rated load and plug rating are given on the data plate Please ensure that these match the household mains supply Important The wires in the mains lead are coloured in accordance with the following code Green yellow earth Blue neutral Brown live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol 4 or coloured green or green and yellow The wire which is coloured blue must be
27. for domestic use and for use in similar environments by guests in hotel or motel rooms bed amp breakfasts and other typical living quarters This does not include common shared facilities or commercial facilities within hotels motels or bed amp breakfasts B gt This tumble dryer must only be used to dry items which have been washed in a water solution and which are marked on the manufacturer s care label as being suitable for tumble drying Dry cleaning kits for freshening up garments in a tumble dryer are increasingly available on the market If using do so at your own risk and follow the instructions provided on the packaging Any other usage is not supported by the manufacturer and could be dangerous Miele cannot be held liable for damage resulting from incorrect or improper use or operation of the tumble dryer Warning and Safety instructions gt The tumble dryer is not intended for outdoor use gt This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge unless they are supervised whilst using it or have been shown how to use it correctly by a person responsible for their safety B This tumble dryer must not be installed and operated in mobile installations e g on a ship Safety with children B Keep children away from the tumble dryer at all times It is not a toy To avoid the risk of injury do not allow the
28. hose length 1 50 m Maximum delivery head 1 50 m Maximum drain hose length 4 00 m AA If the on site water drainage system is not fitted with a non return valve or an appropriate air gap one must be fitted to prevent the risk of back flow See Installation conditions requiring a non return valve The following optional accessories are available an extension hose a non return valve kit for connection to an external condensed water outlet includes an extension hose Maximum delivery head with non return valve fitted 1 00 m Arranging the drain hose N Do not pull on the drain hose and do not stretch it or allow it to become kinked as it could get damaged m There will be a small amount of residual water in the drain hose Have a container ready to collect this 44 m Pull the hose off its connection see arrow m Allow any residual water to run into the container m Unwind the hose and pull it carefully out of the holders m Position the hose to the right or left hand side as necessary Leave the hose in the middle holder to prevent it from becoming kinked inadvertently Installation and connection External drainage via a sink or gully m See Front view illustration f you want to drain the water off into a sink you will need to secure the hose carefully e g by tying it to a tap to make sure it cannot slip during use Otherwise there is a risk
29. icator light for the Start Stop button lights up constantly and then release the Start Stop button The Low temperature indicator light will briefly flash once 50 The option selected will be displayed by a number which will alternate with P O The drying level will be damper Standard setting The Automatic plus indicator light will also flash once e The drying level will be drier The Automatic plus indicator light will also flash twice Pressing the Start Stop button switches from one to the other Switch the dryer off The settings have been changed You can alter the settings again at any time Control m Repeat steps to m Switch the dryer off after step Programmable functions Extending the drying level for the Minimum iron programme The electronics of this dryer ensure a very effective and energy efficient drying process You can however extend the range of the drying level in this programme Follow steps 0 0 0 to programme and store in memory Before you begin first ensure that The dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps O O Switch the dryer on Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button once
30. ing will come on It will go out a few minutes later to save energy m Switch on the dryer by pressing the 4 button m Clean the fluff filters m Close the door m Empty the condensed water container unless the dryer has been connected for external drainage m Check the condenser unit intermittently and clean if necessary see Cleaning and care Extra options Delay start Extra options The relevant indicator light will come on when selected Low temperature For all delicate or minimum iron fabrics with the KJ symbol on the care label e g acrylic garments The programme duration is longer On some programmes Low temperature is a standard part of the programme and so cannot be deselected Buzzer A buzzer sounds at intervals for a maximum of 1 hr to let you know the programme has finished The buzzer will always sound when there is a fault even if it has been switched off Delay start The start of a programme can be delayed by 30 minutes up to 24 hours m Select a programme m Press the Delay start button repeatedly until the required delay period appears in the display The Delay start indicator light will flash The selection can be made in steps of 30 minutes up to 84 and afterwards in one hour steps If you keep the Delay start button pressed in the time will continue to increase up to 24h To begin Delay start m Press the Start Stop button The Delay
31. l m Repeat steps to O m Switch the dryer off after step 55 Programmable functions Standby To save energy the display goes out after 10 minutes and the indicator light for the Start Stop button will start flashing slowly Reactivate from Standby m Turning the programme selector or pressing one of the buttons switches the display back on again This will not alter a running programme On Standby is activated if a programme is not selected after the machine has been switched on after a programme has started However The display will switch on for 10 minutes if Delay start has finished after the end of a progamme or the anti crease cycle The buzzer if selected will sound for 10 minutes after the end of a progamme 56 Factory default settings Not in current programme As in On But The display will not switch off during a programme Off The display will not switch off during a programme Follow steps 0 0 0 to programme and store in memory m See the next page Programmable functions Before you begin first ensure that The dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps Switch the dryer on Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button
32. loaded or The buzzer sounds underloaded the programme will be cancelled This can also happen if the items are already dry The programme is There is no immediate Switch the dryer off and cancelled cause then on again The buzzer sounds Start a programme Cooling down or If the programme stops again Finish is flashing in and Cooling down or Finish the display flashes again there is a fault Contact Miele 33 Problem solving guide Problem Possible cause Remedy The following flashes at the The programme has finished but the laundry is still cooling You can remove the laundry and spread it out to allow the residues end ofa down heat to dissipate or leave it in programme the dryer to cool down more 23 0 3 02 4 The Clean out The dryer is not working Cleaning the filters is airways efficiently or economically usually all that is required indicator light Possible cause Blockages However if the message comes on due to fluff or detergent does not go out after you have cleaned the filters then also check all the possible causes described under The drying process goes on too long or even switches off To delete the message Open and close the door while the dryer is switched on The Clean out airways indicator light can be deactivated see Programmable functions The programme See above for possible To delete the fault
33. m to play on or near it or to play with its controls Supervise children whilst you are using it gt Older children may only use it if its operation has been clearly explained to them and they are able to use it safely recognising the dangers of incorrect use Warning and Safety instructions Technical safety P Before setting up the tumble dryer check it for any externally visible damage Do not install or use a damaged tumble dryer gt Before connecting the tumble dryer ensure that the connection data on the data plate voltage and connected load match the mains electricity supply If in any doubt consult a qualified electrician gt The electrical safety of this tumble dryer can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and regularly tested and where there is any doubt the household wiring system should be inspected by a qualified electrician Miele cannot be held liable for the consequences of an inadequate earthing system e g electric shock gt Do not connect the tumble dryer to the mains electricity supply by an extension lead Extension leads do not guarantee the required safety of the tumble dryer e g danger of overheating gt Unauthorised repairs could result in unforeseen dangers for the user for which Miele cannot acce
34. ms can become hot enough to catch fire Piling stacking or storing oil affected items can prevent heat from escaping and so create a fire hazard If it is unavoidable that fabrics contaminated with vegetable or cooking oil or hair care products be placed in a tumble dryer they should first be washed in hot water with extra detergent this will reduce but not eliminate the hazard gt To prevent the risk of fire the following textiles or products must not be dried in this tumble dryer Items which have been dry cleaned for example with a chemical treatment Fabrics which contain a large proportion of rubber foam rubber or rubber like materials For example products made from latex foam rubber shower caps waterproof textiles rubberised articles and items of clothing and pillows with foam rubber filling Fabrics which contain padding or fillings e g pillows jackets If these were damaged the filling could get out with the risk of igniting in the dryer Warning and Safety instructions B In many programmes the heating phase is followed by a cooling down phase to ensure that the items are not too hot to handle when you remove them this also avoids the danger of the laundry self igniting The programme is not finished until the cooling down phase is complete Ensure that you always wait until the end of the programme before removing the laundry gt Warning Do not switch the tumble dryer off before th
35. n your wrist in the direction of the arrow to open the cover The cover will open downwards The temperature resistant lamp should only be ordered from your Miele Chartered Agent or from Miele 39 After Sales service In the event of any faults which you cannot remedy yourself please contact Your Miele Chartered Agent or Miele see back cover for address When contacting Miele please quote the model and serial numbers both of which are located on the data plate situated on the right hand side below the drum aperture 40 Future updates PC The indicator or check light marked PC on the control panel is the interface used by the Miele service technicians during service work for testing purposes and for updating the machine s programme data Optional accessories Optional accessories for these dryers are available from your Miele Chartered Agent or from Miele Please note that telephone calls may be monitored and recorded to improve our service Installation and connection Front view gt Har Mains connection cable Four height adjustable screw feet 2 Control panel Air inlet and outlet vent for cooling 3 Condensed water container the condenser unit Door External drainage options e g via wash basin wash basin drain outlet Service panel for condenser unit or gully 41 Installation and connection Rear view
36. nto account Creasing in minimum iron fabrics increases with the size of the load This applies in particular to very sensitive fabrics e g shirts blouses If in doubt reduce the size of the load Starched laundry can be dried in the tumble dryer To achieve the usual finish double the amount of starch should be used New dark coloured garments should be washed separately from light coloured garments Do not dry these together with light garments as they may lose their colour also onto plastic components in the tumble dryer Dark coloured fibres can also settle on light coloured garments and vice versa How to dry correctly Brief instructions The headings numbered show the operating sequence and can be used as a brief guide to using your machine Sort the laundry Separate the washed laundry and sort it according to the drying level required the type of fibre or weave sa e SIZE the moisture content after spinning In this way an even drying result will be achieved N Make sure that objects e g detergent dispensing balls have been removed from the laundry They could melt and cause damage to the dryer or the laundry Check seams and stitching to ensure that padding and linings are intact Remove all objects from pockets such as lighters and matches Fasten duvet covers and pillow cases to prevent small items from being r
37. nts suitable for the Cottons and Minimum iron programmes Sort according to colour Denim Max load 3 kg Normal Hand iron Fabric type Denim garments e g trousers jackets skirts or shirts Low temperature Low temperature select this option for delicate fabrics with the symbol on the care label Weight of dry laundry 23 Programme chart Cool air Max load 7 kg Fabric type Any item which only needs airing Warm air Max load 7 kg Item Voluminous and multi layered fabrics whose layers have different drying characteristics e g jackets pillows For drying individual items e g bath towels swimwear tea towels and small loads Note Do not select the longest drying time to start with Check the items as you are drying them to find the optimum time Note You can use the Warm air programme to help remove odours from cotton clothing which has been worn but is still clean select a duration of between 1 2 and 1 hour Items must be suitable for drying in a tumble dryer Dampen the garments a little beforehand or add a fabric conditioner sheet The Warm air programme will not be as effective at removing odours from any parts of the garments which are made of synthetic fibres Low temperature Low temperature select this option for delicate fabrics with the O symbol on the care label Smoothing Max load 1 kg Fabric type Cotton and linen fa
38. oblem Possible cause Remedy The laundry is not The load consisted of Final drying cycle with sufficiently dry different fabrics Warm air Select a different programme next time Items made of synthetic fibres are charged with static electricity after drying Synthetic fibres tend to attract a static charge Static charges can be reduced by adding a fabric conditioner to the final rinse in the washing programme or a fabric conditioner sheet to the load when drying There is a build up of fluff Fluff is principally the result of friction when garments are being worn and to some extent when they are being washed Machine drying hardly causes any fluff to form and has no appreciable effect on the lifetime of the fabric Fluff is collected by the fluff filters and can be easily removed see Cleaning and Care You can alter the drying levels for some programmes see Settings menu 36 Problem solving guide Other problems Problem Possible cause Remedy The drying process goes on too long or even switches off In some circumstances the Clean out airways indicator light still comes on even though the filters are clean Clean out airways Please check all the possible causes and switch the dryer off and then back on again Ventilation to and from the dryer may be insufficient e g because it is installed in a small room This ha
39. olled up inside them Fasten zips hooks and eyes etc Tie fabric belts and apron strings Sew in or remove underwiring from bras Switch on the tumble dryer The tumble dryer may be switched on after loading saving energy as the light will not come on 18 m Switch on the dryer by pressing the A button Load the tumble dryer m Press the Door button to open the door m Load the laundry loosely into the drum Do not overload the drum See the Programme chart for recommended loads for each programme Overloading can cause unnecessary wear and tear to the laundry and give a disappointing drying result m Before closing the door make sure the fluff filter is correctly positioned in the door Check the laundry is right inside the drum so that it cannot get trapped or damaged when the door is shut m Shut the door either with a gentle swing or lean against it and push it shut How to dry correctly O Select a programme O Cottons Automatic plus O O Minimum iron Denim O O Delicates Cool air O o Woollens handcare Warm air O O Express Gentle smoothing O m Select the programme you want The relevant indicator light will come on Indicator lights for drying levels or Extra options and times may also be displayed Programmes with drying levels Using the Cottons Normal Plus programme is recommended for a mixed cotton load and is the programme used in energy consump
40. on and off slowly once and will then flash on and off quickly once 60 O Default setting Keypad tone deactivated Keypad tone activated The Automatic plus indicator light will also flash Pressing the Start Stop button switches from one to the other Switch the dryer off The settings have been changed You can alter the settings again at any time Control m Repeat steps to O m Switch the dryer off after step Programmable functions Adjusting the dryer s electronics for very soft water Extremely soft water can affect the sensitivity of the control electronics Important If the dryer is installed in an area with very soft water you should contact your local water supplier for information and advice regarding water hardness and water conductivity If the water conductivity is less than 150 US the following programmable function will need to be activated This programmable function should not be activated if despite the water being extremely soft as would be the case if a water softener were used its conductivity is greater than 150 pS Otherwise the drying result will not be satisfactory Follow steps 0 0 0 to programme and store in memory Before you begin first ensure that The dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 6 9 Switch the dryer on Wait until the indicato
41. ook If you cannot see any fluff m Replace the condenser unit see following page If you can see some fluff m Clean the condenser unit as described below Cleaning the condenser unit m When rinsing the condenser unit make sure you position it as shown in the next two illustrations m Use a shower head or similar to rinse the unit out as shown 31 Cleaning and care m Then flush the unit through from the front m Check the condenser unit again for any visible fluff and if necessary flush it through again until it has all gone m Remove any soiling still visible inside the housing unit m Also make sure the rubber seals are clean The rubber seals must not be removed and must be free of kinks m Shake any excess water out of the unit until no more water droplets are visible 32 Replacing the condenser unit m With the handle facing upwards push the condenser unit back into position in its housing m Turn the lever down to the horizontal position making sure that the hook on the lever clicks into the groove When replacing the inner cover after cleaning ensure that the rubber seal fits correctly into the groove m Replace the cover making sure the hooks locate correctly Hold it at an angle and push it gently downwards m Then turn the lever upwards into the horizontal position to lock the cover m Replace the service panel and press the upper edge until it clicks into po
42. ormal programme without any Extra options Consumption data can vary from the nominal values given above depending on the size of the load types of textiles residual moisture levels after spinning fluctuations in the electricity supply and any Extra options selected 48 Technical data Height Width Depth Depth with door open Suitable for pushing under a worktop Height Width Suitable for stacking Weight Drum volume Maximum capacity Capacity of condensed water container Drain hose length Maximum delivery head Maximum drain hose length Length of connection cable Voltage Rated load Fuse rating Lamp wattage Test certificates awarded Energy consumption 850 mm 595 mm 634 mm 1 074 mm Yes 850 mm 600 mm Yes 52 kg 1111 7 kg dry weight approx 4 2 1 50 m 1 50 m 4 00 m 2 00 m See data plate see Consumption data 49 Programmable functions Extending the range of the drying level for the Cottons programme The electronics of this dryer ensure a very effective and energy efficient drying process You can however extend the range of the drying level in this programme Follow steps 0 0 0 to programme and store in memory Before you begin first ensure that The dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 6 6 Switch the dryer on Wait until the ind
43. p button switches from one to the other Switch the dryer off The settings have been changed You can alter the settings again at any time Control m Repeat steps to O m Switch the dryer off after step 53 Programmable functions Extending the drying level for the Automatic plus programme The electronics of this dryer ensure a very effective and energy efficient drying process You can however extend the range of the drying level in this programme Follow steps 0 0 0 to programme and store in memory Before you begin first ensure that The dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps O O Switch the dryer on Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button four times The Low temperature indicator light will briefly flash on and off six times 54 The option selected will be displayed by a number which will alternate with P O The drying level will be damper I Standard setting The Automatic plus indicator light will also flash once e The drying level will be drier The Automatic plus indicator light will also flash twice Pressing the Start Stop button switches from one to the other Switch the dryer off The settings have been changed
44. pt liability Repairs should only be undertaken by a Miele approved service technician Ensure current is not supplied to the tumble dryer until after maintenance or repair work has been carried out B Faulty components must only be replaced by genuine Miele original spare parts Only when these parts are fitted can the safety standards of the tumble dryer be guaranteed Warning and Safety instructions P If the connection cable is faulty it must only be replaced by a Miele approved service technician to protect the user from danger B In the event of a fault or for cleaning purposes the tumble dryer is only completely isolated from the electricity supply when it is switched off at the wall socket and the plug is withdrawn or it is switched off at the mains or the mains fuse is disconnected or the screw out fuse is removed in countries where this is applicable B gt In areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the tumble dryer and its surroundings in a clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the warranty gt Do not make any alterations to the tumble dryer unless authorised to do so by Miele Warning and Safety instructions Correct use Caution Risk of fire To avoid the possible danger of fire please read these warnings carefully READ THE INSTRUCTIONS
45. r button m Open the door N Danger of burning Do not touch the back of the drum when adding or removing items The drum and the items can get very hot m Add or remove items as required m Close the door m Press the Start Stop button Time remaining Changes to the programme sequence can alter the estimated time remaining in the display 25 Electronic system lock The system lock prevents your machine being used without your knowledge You can switch on the system lock if required The dryer s electronics are then locked The dryer can still be switched on but a programme cannot be started If an attempt is made to start a programme the indicator light for the Low temperature button will come on and the key symbol o will appear in the display The door is not locked and can be opened at any time Locking Before you begin first ensure that The dryer is switched off The door is closed Press the Low temperature button and keep it pressed in up to step Press the button The Automatic plus indicator light will come on Slowly turn the programme selector three positions stage by stage ina clockwise direction Each of the three programme indicator lights must come on one after the other 26 Now slowly turn the programme selector six positions stage by stage in an anti clockwise direction Each of the six programme indicator lights must come on one aft
46. r light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button ten times The indicator light Low temperature will flash on and off slowly once and will then flash on and off quickly twice The option selected will be displayed by a number which will alternate with P O Default setting Adjusted for very soft water with low conductivity The Automatic plus indicator light will also flash Pressing the Start Stop button switches from one to the other Switch the dryer off The settings have been changed You can alter the settings again at any time Control m Repeat steps to O m Switch the dryer off after step 61 Programmable functions Extending the drying level range You can extend the range of the drying levels for many of the programmes Machine iron plus drier than Machine iron Slightly dry drier than Hand iron Normal plus drier than Normal You can use this programming function only for programmes which allow you to select the drying levels Follow steps 0 0 0 to programme and store in memory Before you begin first ensure that The dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 6 6 Switch the dryer on Wait until the indicator light for the Start Stop button ligh
47. rogramme can be started m Press the Start Stop button The Start Stop button will now light up Perfect Dry only flashes illuminates during programmes with drying levels It remains dark during time controlled programmes see Operating the tumble dryer Note The duration shown in the display is only an estimate and can change Before the end of a programme The heating phase is followed by a cooling down phase Cooling down lights up The programme is not finished until the cooling down phase has been completed There is no cooling down phase with Woollens handcare Remove the laundry when the programme has finished 0 and Finished will appear in the display to indicate that the programme has finished The buzzer if selected will sound at intervals After the programme has finished the drum will continue to rotate for 2 hours at intervals if the garments are not im mediately removed This reduces creasing There is no anti crease with Woollens hanacare The dryer has a standby mode If the Start Stop button flashes slowly during 20 or after the programme this is not a fault see Standby m Press the Door button m Open the door m Remove the laundry Check that all items have been removed from the drum If items are left in the dryer they could be damaged by overdrying when the dryer is next used If the dryer is switched on at the mains and the door is opened the drum light
48. s caused the temperature in the room to rise sharply Open a door or window while the machine is in operation for increased air flow The vents below the door are covered Remove any fluff The fluff filters are clogged with fluff or were still wet when they were replaced Remove any fluff The fluff filters need to be dry Detergent residue hair and fine fluff can block the condenser unit The condenser unit should be checked and cleaned from time to time The laundry has not been spun sufficiently Make sure that your laundry is thoroughly spun at the appropriate spin speed in the washing machine The tumble dryer has been overloaded Do not exceed the maximum load for the programme selected Metallic components e g zippers have prevented the dryer from registering the correct moisture level Open the zippers next time If the problem occurs again dry garments with long zippers using the Warm air programme timed drying 37 Problem solving guide Problem Possible cause Remedy Water leaks from the machine after the condenser unit has been cleaned The inner cover of the condenser unit has not been locked properly and or the condenser unit has not been positioned correctly There is a build up of fluff Ensure that the condenser unit is positioned correctly and lock the inner cover Che
49. sition It is important to ensure that both the condenser unit and the cover are correctly positioned and locked Otherwise water may leak from the machine Problem solving guide Problem solving guide Most faults can be resolved by yourself This will save time and money as a call out charge will apply to customer service visits where the problem could have been rectified as described in these Operating instructions With the help of the following notes minor faults in the performance of the appliance some of which may result from incorrect operation can be put right without a call out being necessary Please note Repair work to electrical appliances must only be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work Check and fault messages in the display Problem Possible cause Remedy O o appears in the The system lock is If you wish to use the tumble display activated dryer the system lock needs The Low temperature to be deactivated see indicator light is Electronic system lock flashing The programme is This is not a fault Use the Warm air programme cancelled In some programmes if to dry individual items i and Finish appear in the drum has been Open and close the door the display over
50. t be consumed It could lead to health problems for people and animals Condensed water can be put to household use e g in a steam iron or humidifier To ensure that any residual particles of fluff in the condensed water are removed before use pass it through a fine sieve or paper filter first 27 Cleaning and care Cleaning the fluff filters The fluff which is created by the drying process is collected by the fluff filters in the door and the door opening Clean the filters after each drying programme Cleaning them whilst dry Tip You can also use a vacuum cleaner to remove the fluff m Open the door and pull the fluff filter 1 out of the door as illustrated m Use your fingers to remove the fluff from the surface of the filter 28 m Remove any fluff from the hollow part of the door opening You could also use a cleaning brush which is available as an optional extra from your Miele Chartered Agent or from Miele or use a vacuum cleaner m Also clean the door seal 2 with a damp cloth m Once clean push the filter back into the door holder until it clicks into position Ensure it is facing the correct way m Use your fingers or a vacuum cleaner to remove the fluff from the two fluff filters in the door opening m Close the door Always check the fluff filters if the Clean out airways indicator light comes on NA clogged filter is a fire hazard The lint filter must b
51. tion tests to AS NZS 2442 Refer to www energyrating gov au website for consumption data Cottons Minimum iron Delicates Express Automatic plus Denim Extra dry O Normal O Hand iron O Machine iron O Cp m Press the relevant button repeatedly until the indicator light comes on with almost all programmes Four drying levels can be selected with Cottons and Express The selection of the other programmes is either limited or not changeable Tip You can extend the range of drying levels for some of the programmes see Programmable functions Woollens handcare Gentle Smoothing this programme cannot be changed Select Cool air Warm air duration The indicator light for the Delay start button will flash when this function is selected m Press the Delay start button until the required time appears in the display Selectable functions Cool air 22 minutes up to hour Warm air 15 minutes up to 2 hours Select any Extra options Delay start m By pressing the relevant button you can select Low temperature Buzzer Delay start see Extra options Delay start Anti crease see next page is always switched on However Delay start is not possible in combination with Warm air Cool air How to dry correctly Start the programme The indicator light for the Start Stop button will flash when a programme is being selected The flashing indicates that a p
52. tor light will briefly flash on and off three times 52 The option selected will be displayed by a number which will alternate with P O Anti crease deactivated 1 hour Anti crease The Automatic plus indicator light will also flash once e Default setting 2 hours Anti crease The Automatic plus indicator light will also flash twice Pressing the Start Stop button switches from one to the other Switch the dryer off The settings have been changed You can alter the settings again at any time Control m Repeat steps to O m Switch the dryer off after step Programmable functions Altering the volume of the buzzer The buzzer has two volumes Follow steps 0 0 0 to programme and store in memory Before you begin first ensure that The dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps O O Switch the dryer on Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button three times The Low temperature indicator light will briefly flash on and off four times The option selected will be displayed by a number which will alternate with P O Default setting Normal buzzer Loud buzzer The Automatic plus indicator light will also flash Pressing the Start Sto
53. ts up constantly and then release the Start Stop button Press the Low temperature button eleven times The indicator light Low temperature flashes short once and long three times 62 The option selected will be displayed by a number which will alternate with P O Default setting Drying level range extended The Automatic plus indicator light will also flash Pressing the Start Stop button switches from one to the other Switch the dryer off The settings have been changed You can alter the settings again at any time Control m Repeat steps to O m Switch the dryer off after step To select the extended drying level m Select a programme m Press the drying level button repeatedly until one or two indicator lights come on Indicator lights Extra dry and Normal Normal plus Indicator lights Hand iron and Normal Slightly dry Indicator lights Machine iron and Hand iron Machine iron plus 63 Miele Australia Pty Ltd ABN 96 005 635 398 Head Office Melbourne 1 Gilbert Park Drive Knoxfield VIC 3180 Miele Gallery and Office Melbourne 208 210 Coventry Street South Melbourne VIC 3205 Miele Gallery and Office Sydney 3 Skyline Place Frenchs Forest NSW 2086 Miele Gallery and Office Brisbane 39 Harvey Street North Eagle Farm QLD 4009 Miele Gallery and Office Adelaide 83 85 Sir Donald Bradman Drive Hilton SA 5033 Miele Gallery an
54. ture Reduced temperature Select Low temperature for sensitive fabrics K Do not tumble dry lroning ZA Very hot ZA Hot A Warm 2X Do not iron Tips on drying See the Programme chart for maximum recommended loads for each programme Overloading can cause unnecessary wear and tear to the laundry give a disappointing drying result and cause more creasing Do not tumble dry loopknit garments Spin garments for at least 30 seconds after washing Open jackets so that they can dry evenly Use the Automatic plus programme for drying mixed loads of cottons colours and minimum iron fabrics Woollen fabrics and wool blends tend to shrink and become matted if dried in a tumble dryer These fabrics should only be dried using the Woollens handcare programme Down filled fabrics have linings which have a tendendency to shrink depending on the quality of the item These fabrics should only be dried in the Smoothing programme Pure linen should only be machine dried if specified as suitable by the manufacturer on the care label Otherwise the surface of the fabric may become rough Loopknit garments e g T shirts underwear have a tendency to shrink after the first wash Therefore To avoid further shrinking do not overdry these fabrics When buying loopknit garments it is advisable to take their shrinkage properties i
55. ways keep the area around the tumble dryer free of dust and fluff Dust drawn into the tumble dryer can cause blockages in the condenser unit over time B Do not let anyone sit or lean on the door as this can cause the tumble dryer to tip up Warning and Safety instructions gt Always close the door after use This way you will avoid the danger of Children climbing onto or into the dryer or hiding things in it Pets or other small animals climbing into it gt The tumble dryer must not be hosed down Accessories gt Only use genuine Miele spare parts and accessories with this appliance If non Miele parts are used warranty performance and product liability claims may be invalidated Miele cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Operating the tumble dryer Control panel Drying Extra dry O Cooling down Delay start Buzzer O Empty container OClean out airways OOO Perfect Dryindicator light For all drying levels See the next page Display See the next page 3 Delay start button This button is used for Delaying the start of a programme Selecting Warm air Cool air Buzzer button An audible tone sounds at the end of the programme Check lights See problem solving guide and After Sales service Start Stop button For starting the programme selected and can
56. will be displayed by a number which will alternate with P O The Clean out airways indicator light is deactivated I The Clean out airways indicator light will come on when there is a heavy build up of fluff The Automatic plus indicator light will also flash once e Default setting The Automatic plus indicator light will also flash twice 3 The Clean out airways indicator light will come on when there is only a light build up of fluff The Automatic plus indicator light will also flash three times Pressing the Start Stop button switches from one to the other Switch the dryer off The settings have been changed You can alter the settings again at any time Control m Repeat steps to O m Switch the dryer off after step 59 Programmable functions Keypad tone An audible tone sounds each time a button is pressed The option selected will be displayed by a number which will alternate with P Follow steps 0 0 0 to programme and store in memory Before you begin first ensure that The dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps Switch the dryer on Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button nine times The indicator light Low temperature will flash
57. y system measures the laundry s residual moisture in programmes with drying levels and provides a more precise drying result After starting the programme the electronics will measure the duration of the programme Estimated time remaining The Perfect Dry indicator light will flash during this time 16 The programme duration will be shown after a short time and the indicator light will go out Once the selected drying level has been reached the Perfect Dry indicator light will remain on until the end of the programme The Perfect Dry indicator light always remains dark during the following time controlled programmes Woollens hanacare Cool air Warm air Gentle smoothing Programme duration Estimated time remaining The expected time will automatically be displayed Estimated time remaining The following factors all affect the estimated time remaining Residual moisture content after spinning type of fabric size of load room temperature fluctuations in power supply The electronics continually assess conditions in the tumble dryer and adjust the estimated time remaining for a more accurate reading Because of this the time displayed can alter during the course of a programme In the same way programmes may finish early This can happen with particularly fine fabrics very small loads or if items were partly dry beforehand Notes on laundry care Care symbols Drying Normal higher tempera
Download Pdf Manuals
Related Search