G402 Giant II Hand Tool Operating Instructions
Contents
1. Operating Instructions G402 Giant II Hand Tool 1 Band may be used from bulk roll as this 2 Continue band around object once 3 Place band in open of tool nose and completely eliminates waste of band Slide more and again through buckle gripper block Move into slot as far as buckle on band as shown bringing end of Double banding develops a great deal possible to avoid buckle sliding into tool band around object to be clamped and more radial compression than single nose Apply tension by turning handle of again through buckle banding Bend end of band under tool buckle 4 Place finger on BAND IT Band at buckle 5 Roll tool over buckle backing off with 6 Pull cutting handle to cut the band bridge while tensioning with tool handle tension handle1 1 turns throughout entire When applying Giant Band clamps prior When you feel BAND IT Band stop moving rolling operation Failure to back off tension to cutting off clamp release band gripper through buckle as you are turning handle with tension handle throughout entire course and push tool nose away from buckle maximum pressure is being exerted by the of roll over may result in breaking of band approx 1 BAND IT Band around object being There is no loss of tension as band released clamped Stop turning handle is used up in the bend 8 Hammer 7 Remove tool down buckle holding stub of band ears to complete down with thumb BAND IT clamp BAND IT IDEX Inc Documen2. in removing threaded parts apply heat to soften locking compound 2 When connecting the tension screw to the slide block clean threads male and female of foreign matter then apply two drops of high strength locking compound Loctite 271 or equiv onto male threads and connect parts together Apply 3 oz of white lubricant or equiv to tension screw thread 3 When connecting the set screw to the cutter bar clean threads male and female of foreign matter then apply one drop of medium strength locking compound Loctite 242 or equiv onto male thread and connect parts together BAND IT IDEX Inc _ TENSION HANDLE TOOL FRAME REPAIR PARTS LIST FOR G40269 SLIDE BLOCK ASSEMBLY INCLUDES SLIDE BLOCK TENSION SCREW ECCENTRIC LEVER AND LEVER PIVOT PIN TENSION HANDLE ASSEMBLY INCLUDES TENSION HANDLE SPIN GRIP AND EXTERNAL RETAINING RING CUTTER BAR ASSEMBLY INCLUDES CUTTER BAR HANDLE CUTTER BAR AND SET SCREW ON FAR SIDE CUTTER BAR G42287 G41275 Document P36187 Rev E peracid al www BAND IT IDEX com ree nee oe ele _ Inc Denver CO 80216 3070 USA All rights reserved P 1 800 525 0758 Page 3 of 3 F 1 800 627 3925
3. t P36187 Rev E A Unit of IDEX Corporation www BAND IT DEX com Copyright ail sl o A BAND IT IDEX Inc 2005 enver Sn tt Page 1 of 3 All rights reserved F 1 800 627 3925 Cleaning and A BAND IT G402 Giant II Warranty 2 Hand Tool Gripper Cleaning Instructions _ 1 Remove gripper Align gripper pin 2 Using a wire brush clean all 3 Replace pin Align gripper hole with hole with notch in tool frame Using a foreign matter from teeth Slide block hole insert pin in hole and punch and hammer punch pin out of hammer pin in place slide block NOTE Periodically apply food grade white lubricant or equivalent to tension screw thread on page 3 to prevent excessive wear If tool fails to securely grip tail of clamp follow gripper cleaning instructions above Refer to website for warranty information http www band it idex com warranty html BAND IT IDEX Inc Document P36187 Rev E A Unit of IDEX Corporation www BAN D IT IDEX com Copyright 4799 Dahlia Street BAND IT IDEX Inc 2005 Denver CO 80216 3070 USA P 1 800 525 0758 F 1 800 627 3925 Page 2 of 3 All rights reserved Tool Assembly y G402 Giant II 1 2 i I i r ir Parts List EX Hand Tool SPIN GRIP EXTERNAL RETAINING RING TENSION SCREW CUTTER BAR HANDLE THRUST h oane BEARING SLIDE BLOCK SET SCREW CUTTER BAR PIN ECC LEVER PIVOT ECCENTRIC LEVER 1 To assist
Download Pdf Manuals
Related Search