Operating Instructions K 6.750
Contents
1. Immediate danger that can cause severe injury or even death Warning Possible hazardous situation that could lead to severe injury or even death Caution Possible hazardous situation that could lead to mild injury to persons or damage to property Symbols on the machine The high pressure jet may not be directed at persons ani mals live electrical equipment or at the appliance itself Pro tect the appliance against frost Environmental protection Oy The packaging material can be recy Varo cled Please do not place the packag ing into the ordinary refuse for disposal but arrange for the proper recycling Old appliances contain valuable ma terials that can be recycled Please arrange for the proper recycling of old appliances Please dispose your old appli ances using appropriate collection sys tems Notes about the ingredients REACH You will find current information about the ingredients at www kaercher com REACH Warranty The warranty terms published by the rele vant sales company are applicable in each country We will repair potential failures of your appliance within the warranty period free of charge provided that such failure is caused by faulty material or defects in man ufacturing In the event of a warranty claim please contact your dealer or the nearest authorized Customer Service centre Please submit the proof of purchase Safety instructions A n Danger Never touch the mains pl2. ON OFF switch Press the trig ger on the gun the unit is ready for use once there is a constant water system STEP 4 gt Connect the high pressure nozzle and press the hand trigger to begin clean ing Start up Caution Dry runs lasting longer than two minutes lead to damages to the high pressure pump If the appliance does not build up pressure within two minutes switch it off and proceed as instructed in the Chapter Troubleshooting Illustration KA gt Push the spray lance into the trigger gun and fasten it by turning it through 90 Illustration gt Unwind the high pressure hose com pletely from the hose drum Hold on to the transport handle during this proce dure Note Ifthe hand crank is in its secured position fold it up first Completely open the water tap Completely uncoil the mains cable Insert the mains plug into the socket Turn on the appliance I ON Operation Danger The trigger gun is subjected to a recoilforce when the water jet is discharged Make sure that you have a firm footing and are also holding the trigger gun and spray lance firmly Caution Prior to cleaning make sure that the high pressure is placed safely on level ground Wear protective goggles and protective clothing during the cleaning process gt Unlock the lever on the trigger gun gt Pull on the lever of the trigger gun the device will switch on Note Rel
3. of their safety or they have received precise instructions on the use of this appliance and have understood the resulting risks Children must not play with this appli ance Supervise children to prevent them from playing with the appliance Keep packaging film away from children risk of suffocation The operator must use the appliance correctly When working with the appli ance he must consider the local condi tions and pay due care and attention to English 3 other persons in particular children who are nearby m Donotuse the appliance when there are other persons around unless they are also wearing safety equipment m Wear protective clothing and safety goggles to protect against splash back containing water or dirt m This appliance was designed to be used with detergents which are sup plied or recommended by the manufac turer The use of other detergents or chemicals may compromise the safety of the appliance Caution m n case of extended downtimes switch the appliance off at the main switch ap pliance switch or remove the mains plug m Do not operate the appliance at temper atures below 0 C m Observe a distance of at least 30 cm when using the jet to clean painted sur faces to avoid damaging paintwork m Never leave the appliance unattended when it is in operation m Make sure that the power cable or ex tension cables are not damaged by run ning over pinching dragging or similar Protect
4. the power cable from heat oil and sharp edges m Allcurrent conducting parts in the work ing area must be protected against jet water m The appliance may only be connected to an electrical supply which has been installed in accordance with IEC 60364 m The appliance may only be connected to alternating current The voltage must correspond with the type plate on the appliance m Forsafetyreasons we recommend that you operate the appliance only via an earth leakage circuit breaker max 30 mA m Cleaning operations which produce oily waste water e g engine washes un derbody washes may only be carried out using washing stations equipped with an oil separator 4 English Safety Devices Caution Safety devices protect the user and must not be modified or bypassed Power switch The appliance switch prevents unintention al operation of the appliance Lock trigger gun This lock locks the lever of the trigger gun and prevents the inadvertent start ofthe ap pliance Overflow valve with pressure switch The overflow valve prevents the permissi ble working pressure from being exceeded Ifthe lever on the trigger gun is released the pressure switch turns off the pump the high pressure jet is stopped If the lever is pulled the pump is turned on again Prerequisites for the appliance s stability Caution Create stability for the appliance prior to all work on or with the appliance to prevent ac cidents or da
5. trigger gun to re lease any remaining pressure in the system Lock the lever on the trigger gun Detach the appliance from the water supply Warning When disconnecting the supply or high pressure hose hot water may leak from the connections after operation gt Pull out the mains plug Yyyy yy gt Caution In order to prevent accidents or injuries keep in mind the weight of the appliance during transport see Specifications When transporting by hand gt Pull the appliance by its transport han dle When transporting in vehicles gt Prior to horizontal transport Remove the Plug n Clean detergent bottle from the intake and close it with the lid gt Secure the appliance against shifting and tipping over Caution In order to prevent accidents or injuries keep in mind the weight of the appliance when selecting a storage location for it see Specifications Storing the Appliance gt Park the machine on an even surface gt Windthe entire high pressure hose onto the hose drum by rotating the hand crank counter clockwise gt Insert the trigger gun with the spray lance into the holder for the trigger gun Illustration gt Stow away the mains cable the high pressure hose and accessory on the appliance Prior to extended storage periods as dur ing the winter also observe the instructions in the Care section Frost protection Caution Protect the appliance and its accessori
6. water can damage the high pressure pump and accessories For protection the use of the KARCHER water filter optional accessory order no 4 730 059 is recommended Water supply from mains Observe regulations of water supplier For connection values see type plate tech nical data gt Use a fibre reinforced water hose not included with a standard coupling Minimum diameter 1 2 inch 13 mm minimum length 7 5 m Caution Hose couplings made of metal with aquas top can damage the pump Please use plas tic couplings or KARCHER brass couplings Illustration gt Screw the coupling element to the wa ter connection on the appliance Push the water supply hose onto the coupling unit then connect it to the wa ter supply How to draw water from a bucket when using a K RCHER Pressure Cleaner K RCHER recommends using the suction hose accessory sold separately Order no 9 505 779 0 STEP 1 gt Connect the suction hose to the water inlet on the pressure cleaner and drop the other end into a bucket Tip If you are not using this accessory coil a hose into the bucket and ensure that you only use a standard hose clamp to connect to the pressure washer CLICK FITTINGS MUST NOT BE USED STEP 2 STEP 3 gt Connect the K RCHER power cord to an electricity source and turn on at pow erpoint Make sure the high pressure nozzle is not connected and turn the unit on at the
7. Illustration DI gt Insert both detergent hoses onto the hose fittings gt Install the dosage regulator and con nect using 2 screws Install the transport handle Illustration E gt Wind up the high pressure hose on the hose drum Illustration gt Slide the free end of the coiled high pressure hose through the recesses on the dosage regulator Illustration A gt Attach the transport handle insert the bolts into the bores and screw them in Illustration El gt Press the connecting fitting from the short high pressure hose into the brass intake until it locks into place audibly Check the secure connection by pulling on the high pressure hose Connect the high pressure hose to the trigger gun Illustration I gt Push the high pressure hose into the 6 English trigger gun until it locks audibly Note Make sure the connection nipple is aligned correctly Check the secure connection by pulling on the high pressure hose Water supply Warning According to the applicable regula tions the appliance must never be used on the drinking water supply without a system separator Use a suitable system separator manufactured by K RCHER or as an alternative a system separatoras perEN 12729 Type BA Water flowing through a system separator is con sidered non drinkable Caution Always connect the system separator to the water supply never directly to the appli ance Note Impurities in the
8. KARCHER K 6 750 Before first use of the unit read these operating instructions and act in accordance with them Operating Instructions 59650570 07 11 General information 2 Safety instructions 3 Description of the Appliance 5 Operation eetet engeus 6 Transports Less resume 9 Storage 9 Maintenance and care 10 Troubleshooting 10 Customer Service 11 Technical specifications 11 Assembly 12 Spare Parts 15 General information Dear Customer Please read and comply with A L these original instructions prior to the initial operation of your appliance and store them for later use or subsequent own ers Scope of delivery The scope of delivery of your appliance is il lustrated on the packaging Check the con tents of the appliance for completeness when unpacking In the event of missing accessories or any transport damage please contact your dealer Proper Use This high pressure cleaner is designed for domestic use only to clean machines vehicles buildings tools facades terraces garden equip ment etc using a high pressure water jet and detergents if required with accessories replacement parts and detergents approved by K RCH ER Observe the instructions provided with these detergents 2 English Symbols in the operating instructions Danger
9. authorized customer service Appliance is not running gt Pull on the lever of the trigger gun the device will switch on gt Check whether the voltage indicated on the type plate corresponds to the volt age of the mains supply gt Check the mains connection cable for damages Pressure does not build up in the appliance Check setting at the spray lance Appliance ventilation Switch on the appliance without con nection the high pressure hose max 2 minutes and run it until the water dis charging from the high pressure outlet is free of bubbles Switch off appliance and reconnect high pressure hose Check the water supply Pull out the sieve in the water connec tion using flat nose pliers and clean un der running water gt gt yy Strong pressure fluctuations gt Clean high pressure nozzle Remove dirt and debris from the nozzle bore us ing a needle and rinse through with wa ter from the front gt Check water flow quantity Appliance is leaking gt Slight leakage from the appliance pump is normal If the leakage increases con tact the authorized customer service No detergent infeed Technical specifications gt Use spray lance with pressure regula tion Vario Power Electrical connection Turn the spray lance to Mix position Voltage 230 V gt Check the settings at the dosage regu 1 50 Hz lator for detergent Connected load 2 2 kW gt i the detergent suction ho
10. ean detergent bottles with locking lids This will make the pesky refilling and filling processes redundant Illustration M gt Remove the lid from the Plug n Clean detergent bottle and press the deter gent bottle into the detergent connec tion with the opening facing down Illustration N gt Adjust the suction volume of the deter gent solution by means of the dosage regulator for detergents gt Use spray lance with pressure regula tion Vario Power gt Turn the spray lance to Mix position Note This will mix the detergent with the water stream 8 English Note If required the washing brushes can be used to work with detergent Recommended cleaning method gt Spray the detergent sparingly on the dry surface and allow it to react but not to dry gt Spray off loosened dirt with the high pressure jet Interrupting operation gt Release the lever on the trigger gun gt Lock the lever on the trigger gun gt During longer breaks more than 5 min utes also turn the appliance off using the O OFF switch Finish operation Caution Only separate the high pressure hose from the trigger gun or the appliance while there is no pressure in the system gt Remove the Plug n Clean detergent bottle from the intake and close it with the lid To store place into the intake ro tated by 180 Release the lever on the trigger gun Turn off the appliance 0 OFF Turn off tap Press the lever on the
11. ease the lever of the trigger gun the device will switch off again High pres sure remains in the system Spray lance with pressure regulation Carrying out the most common cleaning tasks The work pressure can be infinitely regulated between Min and Max gt Release the lever on the trigger gun English 7 gt Turn the spray lance to the desired po sition Note Suitable for working with detergent for this turn the spray lance to the Mix po sition Set the dosage regulator to the desired suction volume for detergent Spray lance with Dirtblaster For particularly dirty items or areas Caution Car tyres paint or sensitive surfaces such as wood should not be cleaned with the dirt blaster as there is a risk of damage Not suitable for use with detergents Washing brush Note Suitable for use with detergents Set the dosage regulator to the desired suction volume for detergent Working with detergent Please use exclusively K RCHER deter gents and care products to carry out the re spective cleaning task as these were specifically developed for your appliance The use of other detergents and care prod ucts may lead to premature wear and can invalidate your warranty claims Please ob tain information at your local dealer or re quest information directly from K RCHER Notes regarding the detergent The most commonly used K RCHER detergents can be purchased ready to use in their Plug n Cl
12. es against frost The appliance and its accessories can get destroyed through frost if there is any water residues in them To avoid damage to them gt Completely drain all water from the ap pliance Detach spray lance from the trigger gun Switch the appliance on I ON press the trigger gun lever until no further wa ter is discharged approx 1 min Turn off the appliance gt Store the appliance and the entire ac cessories in a frost free room English 9 Maintenance and care Troubleshooting Danger Turn off the appliance and remove the mains plug prior to any care and mainte nance work Care Prior to longer periods of storage e g in the winter Illustration U gt Pull out the sieve in the water connec tion using flat nose pliers and clean un der running water Maintenance The appliance is maintenance free Spare parts Use only original K RCHER spare parts You will find a list of spare parts at the end of these operating instructions Special accessories Special accessories expand the possibili ties of using your appliance Please contact your K RCHER dealer for further informa tion 10 English You can rectify minor faults yourself with the help of the following overview If in doubt please consult the authorized customer service Danger Turn off the appliance and remove the mains plug prior to any care and mainte nance work Repair works may only be performed by the
13. g with the jet Risk of explosion Do not spray flammable liquids Never draw in fluids containing solvents or undiluted acids This includes petrol paint thinner and heating oil The spray gt mist thus generated is highly inflamma ble explosive and poisonous Do not use acetone undiluted acids or solvents as they are damaging to the materials from which the appliance is made Warning The mains plug and the coupling of an extension cable must be watertight and must never lie in water Moreover the coupling may never lie on the ground The use of cable reels that ensure that the sockets are at least 60 mm above the ground is recommended Unsuitable electrical extension cables can be hazardous Only use electrical extension cables outdoors which have been approved and labelled for this pur pose and have an adequate cable cross section 1 10m 1 5 mm 10 30 m 2 5 mm Always fully unroll electrical cables from the cable drum High pressure hoses fixtures and cou plings are important for the safety of the appliance Only use high pressure hos es fixtures and couplings recommend ed by the manufacturer The appliance must not be operated by children or persons who have not been instructed accordingly This appliance is not intended for use by persons with limited physical sensory or mental capacities or lacking experience and or skills unless such persons are accompanied and supervised by a per son in charge
14. mage The stability of the appliance is warrant ed when it is placed onto an even sur face Description of the Appliance Coupling element for water connection Water connection with integrated sieve Appliance switch 0 OFF ON High pressure hose Dosage regulator for detergent Storage for trigger gun High pressure hose drum Transport handle Hand crank for hose drum 0 Storage of Plug n Clean detergent bot tle with detergent connection 11 Storage for accessories 12 Storage hook for mains connection cable SI NOV PWwODND 13 Mains cable with mains plug 14 Plug n Clean detergent bottle with locking lid 15 Wheels 16 Trigger gun 17 Lock trigger gun 18 Key to detach the high pressure hose from the trigger gun 19 Washing brush 20 Spray lance with Dirtblaster 21 Spray lance with pressure regulation Vario Power English 5 gt Illustrations on Page 12 13 Before Startup Mount loose parts delivered with appliance prior to start up Install the storage for trigger gun Illustration EN gt Place the bottom holder into the recess es and push forward until it audibly locks in Illustration EI gt Insert the top holder and push down all the way Install the storage hook for the mains connection cable Illustration gt Install the top storage hook Install the dosage regulator for detergent You will need the 2 included screws as well as a Phillips screwdriver PH 2
15. se for Protection class IP X5 Protective class l Customer Service Mains fuse slow blow 16A Water connection Australia K RCHER Pty Ltd Max feed pressure 0 6 MPa 40 Koornang Road Max feed temperature 60 C Scoresby Victoria 3179 Min feed volume 11 l min 1800 675 714 Free Call Max Suction height 1 0m www karcher com au PONEO CEE Working pressure 13 MPa Max permissible pressure 15 MPa 2200 psi Water flow rate 8 2 l min Detergent flow rate 0 3 l min Recoil force of trigger gun 20N Dimensions and weights Length 404 mm Width 448 mm Height 968 mm Weight ready to operate with 20 1 kg accessories Subject to technical modifications English 11 Assembly 12 English Assembly English 13 14 English Spare Parts 2 641 172 0 6 363 410 0 6 391 795 0 9 037 622 0 5 731 620 0 5 965 057 0 07 13 6 465 031 0 English 15 KARCHER as www karcher com au
16. ug and the socket with wet hands The appliance must not be used if the power cord or important parts of the ap pliance e g high pressure hoses trig ger gun or safety devices are damaged Check the power cord and mains plug for damage before every use If the power cord is damaged please arrange for it to be replaced immediately by an authorised repair agent or a skilled electrician Check the high pressure hose for dam age before every use Please arrange for the immediate replacement of a damaged high pressure hose The appliance may not be used in areas where a risk of explosion is present If the appliance is used in hazardous ar eas e g filling stations all of the safety provisions and operating instructions de tailed in this manual must be observed High pressure jets can be dangerous if improperly used The jet must not be di rected at persons animals live electri cal equipment or at the appliance itself The high pressure jet must not be di rected at other persons or directed by the user at him herself to clean clothing or footwear Never use the appliance to clean ob jects containing hazardous substances e g asbestos Vehicle tyres or tyre valves are suscep tible to damage from the high pressure jet and may burst The first indication of this is a discolouration of the tyre Dam aged vehicle tyres tyre valves are high ly dangerous Ensure that a distance of at least 30 cm is observed when clean in
Download Pdf Manuals
Related Search