Standalone AED Trainer Operating Instructions
Contents
1. 6 Turn the AED off The AED will now operate in the chosen training scenario until the scenario is reprogrammed Note that the AED will speak Training Mode each time it is turned on to indicate that it cannot be used to defibrillate a patient Note Training Scenarios 1 9 assume that if the pads are plugged into the AED when the unit is turned on the pads have already been applied to the patient Therefore for proper operation of these training scenarios the student should either apply the pads to the patient before turning the unit on or turn the unit on without the pads plugged in and only plug in the pads after they have been applied to the patient Programming the Default Training Scenario with the IR Remote Control When using the IR Remote Control training scenarios can be selected during operation by using the numeric keys on the remote Defibtech recommends that the AED be programmed to default to Training Mode 10 Pads not Applied when using the IR Remote so the unit always turns on with pads off Page 2 To program the Pads Not Applied Scenario Training Scenario 10 Start with the AED off Power on the AED Press and release the Shift Key on the IR Remote Control Press and release the Alt Key on the IR Remote Control Press and release the Pads Key on the IR Remote Control The AED will say Training Mode 10 Dy OSS If a different default scenario is desired on power up the AED can be2. programmed with the remote control to any of the other 9 scenarios as follows 1 Start with the AED off 2 Power on the AED 3 Press and release the Shift Key on the IR Remote Control 4 Press and release the Alt Key on the IR Remote Control 5 Press a numeric key 1 to 9 to program Training Scenario 1 to Training Scenario 9 6 The AED will say Training Mode n where n corresponds to the numeric key that was pressed The default training scenario has now been programmed and the AED will operate in this training scenario every time the unit is turned on Note that the AED will speak Training Mode each time it is turned on to indicate that it cannot be used to defibrillate a patient Page 3 Available Training Scenarios Different training scenarios can be selected by the instructor either by using the above described selection method or by pressing the appropriate number key on the remote Scenarios 1 8 are based on the American Heart Association AED training scenarios but may be applied to many other training protocols as well Scenario 9 allows for a quick overview and demonstration of AED operation Scenario 10 is recommended as the default scenario when using the Training Package with the remote control The following scenarios are available 1 Persistent VF that does not convert for 3 shocks followed by 1 minute of CPR followed by VF that converts on the 4 shock to a non VF rhythm normal
3. Remote Control Press the Off Key on the IR Remote Control A Note The IR Remote and AED will always respond to SHIFT ALT Key sequences without regard for programmed names As the remote control can be seen by multiple AEDs in the same room it is recommended that the above setup procedures be performed on each AED in a separate room Page 6
4. Defibtech Standalone AED Trainer Operating Instructions Software V2 001 Manual Version 2 002 Defibtech LLC Guilford CT 06437 866 333 4241 DCF 350T Standalone AED Trainer Package Introduction The DCF 350T Standalone AED Trainer package DDU 100TR Trainer AED with DBP RC2 Training Battery may be used to instruct students in the various operating modes of Defibtech DDU 100 series AEDs The DDU 100TR is externally very similar to a standard DDU 100 with the exception that the black rubberized portions of the unit are red This clearly distinguishes the trainer device which cannot be used to defibrillate patients from fully functional DDU 100 AEDs Ten instructor selectable scenarios are provided A remote control can be used to optionally allow the instructor to control the training device and to manually simulate additional training scenarios DCF 350T Standalone AED Trainer Warnings Warning The DDU 100TR Standalone Trainer cannot be used to defibrillate patients Preparing the Training Package The components required to operate the DCF 350T Trainer are DDU 100TR Standalone AED Trainer DBP RC2 Training Battery Pack DDP 100TR Training Pads DTR 400 IR Remote Control Optional Poe The Training Battery Pack should be charged using the appropriate battery pack charger DTR 201 for the DBP RC2 before use The battery will fully charge in 12 14 hours note avoid overcharging for longest battery life when
5. he remote control No other setup of the remote control is required IR Remote Commands In Training Mode the remote control can be used to change the behavior of the AED at any time while the unit is powered on The remote will have no effect on an AED not configured for training The following functions can be performed using the remote control Press the OFF key to turn off the AED Press the PADS key to simulate disconnected pads Press the NSR key to simulate a Normal Sinus Rhythm e g once pads have been applied to the training dummy Press the VF key to simulate Ventricular Fibrillation e g once pads have been applied to the training dummy Press the MOTION key to simulate a cardiac rhythm corrupted with excessive motion artifacts e g once pads have been applied to the training dummy Press a Numeric Key 1 to 9 to instantly change the training scenario to one corresponding to that key i e 1 begins Training Scenario 1 2 begins Training Scenario 2 etc Press the VOLUME UP key to increase the volume of the AED s voice output Subsequent pressing of the VOLUME UP key will cause the volume to incrementally increase Once the volume has increased to the maximum possible pressing the VOLUME UP key will have no effect Press the VOLUME DOWN key to reduce the volume of the AED s voice output Subsequent pressing of the VOLUME DOWN key will cause the volume to incrementally decrease Once the volume ha
6. proper charging procedures are followed the battery pack should have a life of approximately 200 charge discharge cycles The Training Battery Pack does not require a 9V battery If a 9V battery is installed and the AED is turned off the ASI will blink red and a warning chirp will be generated to warn the user that the AED is not capable of operating as a rescue defibrillator The AED will run the last programmed training scenario every time it is turned on see Programming sections below Page 1 Programming the Default Training Scenario without the IR Remote Control The Training Battery Pack retains the last programmed training scenario and plays that scenario every time the AED is turned on until a different training scenario is programmed The instructor may select from the available training scenarios listed below Use the following programming procedure when an IR Remote Control is not available 1 Start with the AED off Hold the Shock button down while turning the unit on 3 The unit will announce Training Mode followed by the currently set scenario number 4 Release the Shock button 5 Thereafter each time the Shock button is pushed the scenario number will advance and the AED will speak the scenario number Push the Shock button until the desired scenario number is spoken note it is ok to push the Shock button rapidly without waiting for the numbers to be spoken in order to advance more quickly
7. s decreased to the minimum possible pressing the VOLUME DOWN key will have no effect Press the PAUSE key to alternately suspend and resume AED operation Once paused the AED will only respond to the PAUSE key of the IR Remote Control Page 5 IR Remote with Multiple AEDs The IR Remote Control can be used with up to four AEDs in a large classroom In order to individually command a given AED with the IR Remote each AED must be programmed with a unique name The IR Remote provides four alphabetically labeled keys A through D which are used to name the AEDs and then may be used as a prefix to any of the commands described in the previous section e g pressing A then NSR causes AED A to simulate a normal sinus rhythm pressing D then PAUSE will cause AED D to suspend operation To give a specific AED a unique name the following procedure must be performed Start with all the AEDs off Turn on the AED that is to be programmed Press and release the Shift Key on the IR Remote Control Press and release the Alt Key on the IR Remote Control Press one of the four alphabetically labeled keys on the IR Remote Control A to D to set the AEDs name Gyo To remove the programmed unique name from an AED the following procedure must be performed Start with all the AEDs off Power on the AED that is to be programmed Press and release the Shift Key on the IR Remote Control Press and release the Alt Key on the IR
8. sinus rhythm 2 VF that converts on the 2 shock to asystole non shockable rhythm 3 VF that converts on the 2 shock to a non shockable rhythm normal sinus rhythm Non shockable rhythm throughout Persistent VF that does not convert for 3 shocks followed by 1 minute of CPR followed by VF that converts on the 4 shock to a non VF rhythm normal sinus rhythm Non shockable rhythm throughout VF that converts on the 2 shock to a non shockable rhythm then patient refibrillates and then converts to a normal rhythm after a 3 shock 8 Bad pads indication until the pads connector is removed and plugged back in simulating replacement of the pad set followed by VF that converts on the 2 shock to a non shockable rhythm normal sinus rhythm 9 VF that converts on the 1 shock to a non shockable rhythm normal sinus rhythm 10 Pads are not applied to the patient This scenario is used with the IR Remote Control where the instructor can interactively select different rhythms such as NSR and VF or any one of the predefined Training Scenarios after the student has applied the pads to the patient dummy ie SO Note that when the Trainer AED is turned on it will power up in the default scenario and not in the last used scenario see previous section on how to set the default scenario Page 4 IR Remote Setup Before using the remote insert two AAA batteries into the battery compartment in the back of t
Download Pdf Manuals
Related Search