Flush--trimming unit Operating Instructions
Contents
1. roll not tracing with spindle 9 according to the scale Workpiece projection 1 5 mm For all settings Carry out a trial cut then correct the setting Edge thickness and permissible feed speed at maximum 3 mm edge surplus 6 Turning or changing the reversible tool in the router Undo the grub screw with 5 Turns of an Allen This is just one example there are no other ma key kes with slightly different changing methods Our Slide the clamping wedge 36 with reversible recommendation clean all parts well If both cut tool 37 laterally out of the blade groove ting edges are blunted fit a new reversible tool Turn or change the reversible tool and place it in the groove together with the clamping wedge with the unused cutting edge pointing upwards Place the router bit on steel plate so that the lateral projection of the reversible tool cutter is of the same size Caution Press the top cutting edge of the reversible tool A Cutting edges are sharp with light finger pressure against the support surface 38 and 39 and tighten one grub screw 40 lightly then both of them in alternate sequence 7 Servicing and care of the router unit Clean the unit when work is finished The HOLZ Her router is maintenance free Lightly grease moving parts such as sliding The extractor is highly efficient and the blower surfaces and spindles nozzle is pneumatically controlled such that it Check tools f2. HOLZ HER REICH Spezialmaschinen GmbH Flush trimming unit 1 962 Operating Instructions Art Nr 209 0538 09 90 Contents 4 1 4 2 5 1 5 2 10 Getting to know the router Putting the router unit into service Operating the edge banding machine without router Fitting the tool Removing the router bit Inserting the router bit Adjusting and operating the router unit Flush cutting Edge surplus cutting Turning or changing the reversible tool in the router Servicing and care of the router unit Troubleshooting Specifications Tools and accessories Page DODORhAhAA RO mul ee la ooo 1 Getting to know the router Bottom router unit Motor 1 Vertical tracer roll 2 Knurled setting screw 3 plus vernier scale Vertical adjuster of router unit with knurled screw 4 plus scale 5 Top router unit Motor 6 Vertical tracer roll 7 Knurled setting screw 8 plus vernier scale Vertical adjuster of router unit with knurled screw 9 plus scale 10 Stand Base 11 Horizontal adjustment of entire unit according to scale 12 2 Putting the unit into service Close the guard Switch on the master switch of the edge banding machine Switch on the feed of the edge banding machine Switch on the router unit Before starting the setting work reset the router so that the stock can enter it without contact for a trial run All switches are off and secured during settin
3. g work 3 Operating the edge banding machine without router unit Undo the clamping bolts 1 Retract the router with the spindle 2 Tighten the clamping bolts 1 4 Fitting the tool 4 1 Removing the router bit Undo the bolt 3 and nut 4 Swing away the plate 5 Move out the motor and hang it onto stand Hold the motor shaft with a WAF 6 spanner and undo the fastening nuts with a WAF 19 hex spanner Remove the router bit Important Switch off the master and the unit switches and secure them with a padlock 4 2 Inserting the router Insert the router bit with the cutting edge in the Direction of rotation in the top and bottom router direction of the motor arrow units against the direction of feed chain operation Tighten the nut well by applying counter pres of the edge banding machine sure with a spanner Insert the motor Swing the plate 5 and tighten the bolt 3 Check the motor position using the scale 6 Tighten the nut 4 5 Adjusting and operating the router unit Undo the clamping bolt 1 in each case Set the unit with the spindle 2 in accordance with the scale Tighten the clamping bolt 1 5 1 Flush cutting Tracer rollers are flush when the cutting circle is at scale position 0 Correction of bottom router unit at spindle 7 Correction of top router unit at spindle 8 5 2 Edge surplus cutting Top edge surplus adjust the entire router unit Top tracer
4. op and bottom Art No 209 6129 Counter for horizontal shifting of assembly Art No 131 0895 Pneumatic unit shift device Art No 209 1054 Vertical tracer shoe compl for Art No 209 1666 overhanging edgings Settings tools WAF 6 spanner For router bit change Double ended open jaw spanner For setting the router horizontal and WAF 17 19 top and bottom router units Motor attachment router bit change or motor arbor adjustment Crank Horizontal adjustment of complete router motor adjustment 12 Warranty Our general terms of business shall apply with regard to warranty Spare parts are available either from your dealer or from the manufacturer Only genuine HOLZ HER spare parts may be used in HOLZ HER machines for warranty reasons P O box address REICH Spezialmaschinen GmbH Postfach 1803 72608 N rtingen Germany Telephone 49 7022 702 0 Telefax 49 7022 702 101 E Mail marketing holzher de Internet http www holzher de ES Company address REICH Spezialmaschinen GmbH Plochinger Stra e 65 72622 N rtingen Germany 13
5. or functioning and sharpness only operates during cutting work 8 Troubleshooting Edge is not completely flush cut up to the end 1 Stock is not right up against the intake fence of stock push it into flush contact 2 Incorrect positioning of router set correctly see 5 3 Edges are curved too long in storage 4 Tracer rolls incorrectly set readjust the tracer rolls see 5 10 9 Specifications 9 1 Mode of operation Top and bottom cutting conventional Verticaly tracing Router unit does not swivel 9 2 Working dimensions Edge thickness max 30 mm Edge height 66 mm Edge surplus max 3 mm Cutting cross section approx 90 mm adjustment of tracer rollers to cutting circle 1 mm 6 mm Displacement travel of router horizontal 60 mm 9 3 Drive Motor output 2 x 1 86 kW 3 72 kW Motor speed cutter spindle 12000 min t 9 4 Connection load of both motors 2 x 1 86 kW 3 7 kW Motor 2 x 1 86 kW 3 7 kW at 220 V 200 Hz 12 A 2x 4 5 A 9 5 Extractor Air requirement 700 m h cbm h Dynamic pressure 6 7 mbars Connection 2x0 70 mm 9 6 Weight approx 85 kg 11 10 Tools and accessories Router Steeel body Y 80 x 30 x 40 Art No 032 4299 1setof reversible tools carbide Art No 032 4302 tipped 4 pieces 40 mm Special accessories Blower nozzle Art No 129 6957 Elec brake Art No 129 6183 Counter for tracer roll vert t
Download Pdf Manuals
Related Search