Panasonic Ducted CSF24 50DD1E5 Operation Manual
Contents
1. La LU Before operating the unit read these operating instructions thoroughly and keep them for future reference P07 T10130 Panasonic Operating Instructions Air Conditioner Indoor Unit CS F24DD1E5 CS F28DD1E5 CS F34DD1E5 Outdoor Unit Inverter Model HBE5 Series CU YL24HBE5 CU YL28HBE5 CU YL34HBE5 CU YL43HBE5 GBE5 Series CU YL24GBE5 CU YL28GBE5 CU YL34GBE5 CU YL43GBE5 Heat pump Model CU B24DBE5 CU B28DBE5 CU B34DBE5 Cooling Model CU J24DBE5 CU J28DBE5 CU J34DBE5 CS F43DD1E5 CS F50DD1E5 DBE5 DBE8 Series CU L24DBE5 CU L28DBE5 CU L34DBE5 CU L43DBE5 CU L50DBE8 CU B28DBE8 CU B34DBE8 CU B43DBE8 CU B50DBE8 CU J24DBE8 CU J28DBE8 CU J34DBE8 CU J43DBE8 CU J50DBE8 SAFETY PRECAUTIONS DEFINITION The instructions to be followed are classified by the following symbols This symbol denotes an action 2 E FA These symbols denote actions that is PROHIBITED u that are COMPULSORY To prevent personal injury injury to others or property damage please observe the following Incorrect operation due to failure to follow instructions may cause harm or damage the seriousness of which is classified as below This sign warns of Warning This sign warns of death or serious injury Caution injury or damage to property e Do not install the unit in a SN potentially explosive atmosphere e Do not wash the unit with water benzene thinner or scouring powder e Do not u2. the manufacturer its service agent or similarly qualified persons in order to avoid a hazard This equipment must be earthed and strongly recommended to be installed with Earth Leakage Circuit Breaker ELCB or Residual Current Device IRCD Otherwise it may cause electrical shock or fire in case of malfunction Ax In case of emergency or abnormal E conditions burnt smell etc turn off the power supply and consult your nearest dealer MIT LOTH a Outdoor Uni Do not sit or step on the unit you may fall down accidentally e Do not touch the sharp aluminum fin sharp parts may cause injury Ensure that the drainage pipe is connected properly Otherwise leakage may occur After long periods of use make sure the installation rack is not damaged Do not insert your fingers or other objects into the unit sharp parts may cause injury PO7 T10130 indd 2 4 21 2008 10 08 52 AM Thank you for purchasing Panasonic Air Conditioner REGULATORY INFORMATION This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance OPERATION CONDITION ing tempera
3. air operation is started PRE HEAT appears on the remote control display Operation starts after power resumes e Auto restart is in function and operates under previous setting During dry mode cold air blow out e The unit is running cooling operation with low fan speed to dehumidify the room Fan speed change occasionally during heating The room temperature has reached the remote control setting When the mode room temperature drops again the fan speed will resume to the remote control settings Outdoor unit emits steam during heating e This is due to defrost operation happens at the heat exchanger mode PO7 T10130 indd 8 4 21 2008 10 09 04 AM efore calling for servicing Symptom Check Heating Cooling operation is not working e Set the temperature correctly efficiently e Close all doors and windows e Clean or replace the filters Clear any obstruction at the air inlet and air outlet vents Heating mode cannot be operated e The unit is forced to operate at cooling mode only in a non living room such as a computer room Noisy during operation e Check if the unit has been installed at an incline or the intake grille is not closed properly The unit does not work e Check if the circuit breaker is tripped e Check if timers have been set If the CHECK indicat Turn off the unit remote control e Turn on again after 3 minutes e If CHECK continues to blink press for error messages If problem
4. complies with the requirement set by the Directive for the chemical involved e Do not switch ON the unit when waxing the floor After waxing aerate the room properly before operating the unit e Do not install the unit in oily and smoky areas 3 PO7 T10130 indd 3 4 21 2008 10 08 55 AM PRODUCT OVERVIEW S OPERATIONS WIRED REMOTE CONTROL Air outlet Air inlet CZ RD513C 7 TEMP TIMERCLOCK AIC No no FAN OMODE y UP y SET SPEED MODE UP SELECT POWN CANCEL AUTO MANUAL DOWN I AIR SWING L e e CHECK JODOUR WASH VENTILATION TESTRUN FILTER RESET e For normal operation the A and buttons are not in use Remote Control Preparation a p SELECT fess gt 2 Press to set day 3 Confirm 4 Repeat steps 2 and 3 to set the current time PO7 T10130 indd 4 OFF ON D TO TURN ON OR OFF THE UNIT TO SET TEMPERATURE e Selection range 16 C 31 C MODE TO SELECT OPERATION MODE AUTO mode For your convenience e Unit selects operation mode according to temperature setting outdoor and room temperature HEAT mode To enjoy warm air Unit takes a while to warm up Applicable for Inverter Heat pump Model FAN mode To enables air circulation in the room COOL mode To enjoy cool air DRY mode To dehumidify the environment e Unit operates at low fan speed to give a gentle cooling operation During soft dry operation the indoor fan operates at a low
5. cooling process Water flowing sound during operation Refrigerant flow inside the unit The room has a peculiar odour e This may due to damp smell emitted by the wall carpet furniture or clothing Indoor fan stops occasionally during automatic This helps to remove the surrounding odours fan speed setting Operation is delayed a few minutes after The delay is a protection to the unit s compressor restart Outdoor unit emits water steam e Condensation or evaporation occurs on pipes Indoor fan stops occasionally during heating To avoid unintended cooling effect operation Cracking sound can be heard during e Changes of temperature cause the expansion contraction of the unit operation Unit switch to FAN operation and air become This happens when the room temperature reaches the set temperature humid operation switches to FAN mode and the humidity increase Outdoor unit emits noise during heating e This is due to changes inflow of refrigerant gas when operation stops operation and starts Operation does not stop immediately after e Discharging heat is in process Operation will stops automatically after pressed the OFF ON button approximately 60 seconds Operation stops occasionally DEFROST e The unit is in defrosting mode and the melted frost is drained from the appears on the remote control display outdoor unit Airflow does not start immediately after e The unit is warming up to provide warm
6. fan speed e The louvers movement might not align with the remote control display 4 21 2008 10 08 56 AM FAN ZTOISET DAILY TIMER SPEED TO SELECT FAN SPEED 3 OPTIONS gt To turn ON or OFF the unit at a preset time ideen ae Fir 1 2 For AUTO the indoor fan speed is automatically MODE SELECT adjusted according to the operation mode Ifthe operation mode is set to Fan the fan speed will 2 be fixed at MED regardless of the temperature setting Enter daily timer mode Select ON or OFF timer ECONOMY 3 TO REDUCE POWER CONSUMPTION UP amp Recommend to use when desired room temperature is en reached Economy operation can be activated in all modes and can be cancelled by pressing the respective button Set the time Confirm again ANCEL To cancel ON or OFF timer press 0 l ODOUR WASH e When ON timer is set the unit may start early before ODOUR REMOVING the actual set time in order to achieve the desired e Helps to remove unpleasant odour from the surrounding area during operation To enable the odour removing function press the eo once l e To cancel press the respective button again ODOUR CLEAR Timer operation is based on the clock set in the remote control and repeats daily once set For clock setting please refer to Remote Control preparation The timer closest to the current time will be activated first Applicable for Inverter model only If timer is cancel
7. led manually you can restore the e To remove odour and minimize the growth of odour previous setting by pressing causing moulds in the air conditioner s interior section If the main power is switched off for an hour or more To enable this function press the oos for more than the clock and timer will need to be set again 3 seconds The unit will automatically perform Fan and Heating modes for approximately 20 minutes and then stops automatically e Recommended to open the windows during this operation HINTS e Set the temperature 1 C higher in cool mode or 2 C lower in heat mode than the desired temperature to achieve a 10 power saving e Use curtains to screen off sunlight and outdoor heat to reduce power consumption during cool mode P07 T10130 indd 5 4 21 2008 10 08 58 AM TO SETaWEEKLY TIMER Will light up if Timer operation is selected 6 different programs can be set in a day 1 6 y 31 2 34 5 6 Indicate the ON TUE WED THU FRI SAT SUN selected day ON a Time to be OFF selected Interval Ze 10 minutes OFF Timer To automatically switch OFF the unit ON Timer To automatically switch ON the unit e Day to be selected Change Display 1 Press e for 3 seconds to change the display to weekly timer Select days to run timer SELECT 2 Press 5 to enter day setting 3 Press to select your desired day The selected day will be highlighted wi
8. persist please consult your nearest authorized dealer NON SERVICEABLE CRITERIAS TURN OFF POWER SUPPLY then CALL Authorized Distributor under the following conditions e Abnormal noise during operation Water foreign particles have entered the remote control e Water leaks from Indoor unit e Circuit breaker switches off frequently e Power cord becomes unnaturally warm e Switches or buttons are not functioning properly e The odour persists even after odour wash operation is used continuously PO7 T10130 indd 9 4 21 2008 10 09 04 AM P07 T10130_Memo indd 10 4 21 2008 10 10 18 AM PO7 T110130_Memo indd 11 4 21 2008 10 10 20 AM IWIRED REMOTE CONTROL E Start stop the operation Inverter Heat pump model Hae e AUTO gt HEAT gt Select the desired mode OMODE S os SPEED gt ue P DRY lt COOL lt FAN ne D MANUAL DOWN Cooling model fe gt SE AUTO gt FAN ECO A A O a ae DRY COOL SZRDSISC a Select the desired temperature Matsushita Electric Industrial Co Ltd Web Site http www panasonic co jp global Printed in China P07 T10130 OSPT0803 00 PO7 T10130_Back indd 12 4 21 2008 10 09 27 AM
9. se for other purposes such as preservation of food e Do not use any combustible equipment in front of the airflow outlet e Do not expose directly to cold air for a long period Ensure that the drainage pipe is connected properly Otherwise leakage may occur Aerate the room regularly e Do not install remove and reinstall the unit by yourself improper N installation will cause leakage electric shock or fire Please consult an authorized dealer or specialist for the installation work Do not insert your fingers or other objects into the unit Do not attempt to repair the unit by yourself Remote Control e Switch off the power supply before E cleaning or servicing Turn off the power supply if the unit is not used for a long period of time This air conditioner is equipped with a built in surge protective device However in order to further protect your air conditioner from being damaged by abnormally strong lightning activity you may want to disconnect it from the power supply Do not touch the air conditioner during lightning it may cause electric shock VUNDIN Do not Sue Br same power outlet with other equipment e Do not modify power cords e Do not use extension cords e Do not operate with wet hands Use the specified supply cord If the supply cord is damaged it must be _ replaced by
10. th W Press to deselect or select WW mark Repeat this step includes other day Select ON OFF Timer SELECT 4 Press a to enter Timer 1 5 Press to choose ON or OFF 6 Press O to confirm the selection Select Timer 7 Press to select your desired time If you want to set together with your desired UP temperature press 2 to select the temperature p p Y p 8 Press to confirm the setting 5 CANCEL e Repeat steps 5 to 8 to set Timer 2 to 6 or press to cancel the related timers PO7 T10130 indd 6 OPERATION DETAILS e Weekly timer Is only applicable for wired remote control press e for 3 seconds to select daily timer or weekly timer e Daily timer and weekly timer could not be set at the same time e Promotes energy saving by allowing you to set up to 6 timers in any given day Same timer program cannot be set on the same day Check Timer 1 Enter timer mode 2 Select the day 3 The display will show the program for each of the selected day Modify Or Add Timer e Perform check timer operation to select the day Repeat steps 4 to 8 to modify existing timer program or add any new timer program Cancel Timer e Perform the step below to cancel the timer program for a particular day 1 Enter timer mode 2 Select the day 3 Press to enter day setting 4 Press to cancel the timer set Disable Weekly Timer MODE e To disable weekly timer setting press gt
11. then CANCEL press Enable Weekly Timer OMODE To enable previous weekly timer setting press then press 4 21 2008 10 08 59 AM CARES CLEANING N e Switch off the power supply before cleaning e Do not touch the aluminium fin sharp parts may cause injury CAUTION WASHING INSTRUCTIONS Please consult your nearest dealer for any suction or discharge air grille optional parts cleaning Do not use benzene thinner or scouring powder Use only soap pH7 or neutral household detergent Do not use water hotter than 40 C Air Filter Maintenance Cleaning is needed when e Please consult your nearest dealer for any air filter maintenance or IN MON TUE WED THU FRI SAT rah AUTO COOL DR Dey FILTER L cleaning 7ER ah ae g i icki Gem After the air filter is cleaned press O _ to reset FILTER RESET FILTER RESET appears on the remote control display FOR SEASONAL INSPECTION AFTER EXTENDED NON USE No obstruction at air inlet and air outlet vents e These units are mounted inside the ceiling It uses external air intake vent and air outlet vent to operate Please consult your nearest dealer for seasonal inspection FOR EXTENDED NON USE e Activate heat mode for 2 3 hours to remove moisture left in the internal parts thoroughly e Turn off the power supply PO7 T10130 indd 7 4 21 2008 10 09 03 AM Mist emerges from indoor unit e Condensation effect due to
12. ture range Model Temperature C EAA cooing Mamm 2 3 a DBEB Series HEATING coomo Maximum 43 me nearing Maximum ar a Mesina 2 49 _ esc NOTICE This unit is still able to operate as a cooler with outdoor temperature as low as 15 C 10 C in a non living room such as a computer room with a room temperature of 21 C or above and room humidity up to 45 CU YL24HBE5 CU YL28HBE5 CU YL34HBE5 CU YL43HBE5 Temperature C UY Maximum 82 o NOTEI nn a PRODUCT OVERVIEW amp OPERATIONS WIRED REMOTE CONTROL QUICK GUIDE BACK COVER The illustrations in this manual are eae for explanation purposes only and may difer rom the actual un is NOTICE This unit is still able to operate as a cooler with outdoor temperature as low subjected to change without notice as 5 C in a non living room such as a computer room with a room for future improvement temperature of 21 C or above and room humidity up to 45 ii Information for Users on Collection and Disposal of Old Equipment and used Batteries Information on Disposal in other Countries outside the European Union These symbols are only valid in the European Union If you wish to discard these items please contact your local authorities or dealer and ask for the correct method of disposal Note for the battery symbol bottom two symbol examples This symbol might be used in combination with a chemical symbol In this case it
Download Pdf Manuals
Related Search