Operating Instructions Type 0282 Voltage 12V or 24V UL / UR valid
Contents
1. Instructions Wiring Diagram Electrical Connection Type 2509 Power Ground green dot Power Orientation is not important Electrical Connection Ensure supply voltage frequency corresponds with that on label Voltage tolerance is 10 Available Electrical Connections see Marking Wiring diagram see above For this product to be considered UL listed and CSA approved for General Purpose and FM approved for Hazardous Locations Division 2 it must be in conjunction with the type 2509 cable plug connector Electrically Operated Valves Parts YSYI2 The connector and gasket must be assembled to the valve with the screw provided after the connection of the wire leads This valve and connector assembly is delivered together and is to be used as one unit For valves to be used in Intrinsically Safe Applications the positive pole is identified by a on the pin or wire No 1 has to be con nected to the See Control Drawing for the Rules of Interconnection Warning All valves to be used in Intrinsically Safe Applications must be clearly marked as Intrinsically Safe Apparatus Trouble Shooting Check port connections minimum operating pressure differential if required and supply voltage Ensure pilot hole in piston is clear and pilot bore in the valve outlet is not abstracted If core does not pull in check for short circuit coil burn out or foreign matter im peding core movement A jamme2. MAN 1000010130 EN Version printed 02 07 2010 Status RL released freigegeben burkert Operating Instructions Type 0282 Design 2 way solenoid valve direct acting function A or normally open et See Table Fluid and Ambient Temperat re For Hazardous Locations Div 1 T4 Max Ambient Temperature Max Fluid Temperature 104 F 40 194 F 90 For Hazardous Locations Div 2 and Ordinary Locations See Table Pressure Range Minimum pressure differential between and outlet port is 3 PSI Maximum inlet pressure see label on valve Installation Before installing valve ensure that piping etc is free of foreign matter metal fillings seal material welding scale etc PTFE tape is recommended for sealing ports Arrow on valve body gives flow direction Installation as required but preferably with coil uppermost Installation in this position tends to prevent foreign matter remaining in pilot valve increased life A strainer upstream of valve protects against effects of foreign matter Do not put any loads on coil unit Pipework should be supported such that valve body is not under strain Do not allow a pipe end or sealing material to block the pilot bore within the valve outlet Inlet and outlet of valve must be fullbore and pipework unrestricted Stainless Steel Seal Material EPDM EPDM NBR NBR FKM FKM Circuit function A Normally Closed B Normally
3. Open T 22 0282 A 3 4 FKM BR id s NPT3 4 PMAX 170 PSI E l24V 60Hz 8W a ia 450000Y eatin Recorder No Voltage Frequency Power Consumption Maximum Pressure Approvals The valve is either approved as General Purpose valve for Hazardous Locations Class Division 1 Group A B C D Class II Division 1 Group E F G Class Ill Division 1 and 2 Operating Temperature T 4 or FM approved as Nonincendive for Hazardous Locations Class I Division 2 Group A B C D Class Il Division 2 Group F G Class III Division 1 and 2 Operating Temperature T 4A or UL listed for Ordinary locations or CSA approved for Ordinary locations See label on the valve Seal Materials N wt oO O g Fluid Temperatures F Buna N o i D Air Fluid T 32 to 194 a Ambient 14 to 130 8 Water Fluid T 50 to 194 S Ambient 32 to 130 172 6 Neutral Gas Fluid T 32 to 194 v Ambient 14 to 130 2 Light oil Fluid T 50 to 194 gt Ambient 14 to 130 LP gas Fluid T 32 to 140 a Ambient 14 to 130 Ethylene FKM Propylene 22to 194 14 to 194 14 to 130 14 to 130 50 to 194 50 to 194 32 to 130 32 to 130 22 to 194 14 to 194 14 to 130 14 to 130 50 to 194 14 to 130 14 to 140 14 to 130 printed 02 07 2010 Status RL released freigegeben MAN 1000010130 EN Version burkert Operating
4. d or missing core causes the coil to overheat in the case of AC supply Warning These products are designed to operate in a wide variety of ap plications it is the user s responsibility to select a model that is appropriate for the application This product is designed to be installed only by suitably qualified and trained personnel Specifications should not be exceeded under any circumstances The torque for the terminal screw on type 2509 is 0 5 Nm 4 4 Ibf in Changes made to this product will render any applicable warranty null and avoid Specifications subject to change without notice Any questions Please call Biirkert Contromatic Technical Service at 949 223 31 00 burkert Germany Contact address Birkert Fluid Control Systems Sales Center Chr Burkert Str 13 17 D 74653 Ingelfingen Tel 49 0 7940 1091 111 Fax 49 0 7940 1091 448 E mail info de buerkert com International Contact addresses can be found on the Internet at www burkert com gt Burkert gt Company Locations
Download Pdf Manuals
Related Search