Installation Manual
Contents
1. Mounting Bracket thermoral HEATED TOWEL RAIL Warranty Thermogroup covers all its products with a satisfaction guarantee In addition Thermogroup will supply a replacement product where a fault is shown to be caused by manufacture materials or workmanship providing the goods have been installed correctly and according to installation instructions This guarantee does not include removal freight or installation costs Thermogroups products come with guarantees that cannot be excluded under the Australian Consumer Law and you are entitled to a replacement or refund for a major failure amp compensation for any other reasonable foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure All of the standard Thermorail Heated Towel Rails come with a 5 year warranty and the Budget range with a 3 year warranty To use the warranty repair or service the customer must provide purchase invoice receipt and any other relevant details The consumer shall in the first instance of a fault or claim contact the retailer from whom the product was purchased If the product develops a fault within the warranty period due to normal wear and tear Thermorail will at its discretion recognise whether it s a faulty product or not If it is impossible or not economical for the manufacturer to repair the product the manufacturer w2. be plugged into a standard GPO Alternatively they can be hard wired by a licensed electrician Care and Cleaning The polished stainless steel finish of your Thermorail Heated Towel Rail is hard wearing and easy to maintain Clean with a soft clean cloth and a non abrasive cleaning agent Any harsh scrubbing or scratching will damage the surface as well as the use of any cleaning products which contain acid or corrosive agents will damage the surface Concealed Wiring Bracket This Thermorail Heated Towel Rail contains a kit for both concealed and exposed wiring If you have access to the wall cavity the concealed option will allow for a neater and more visually appealing installation Installation Thermorail Heated Towel Rail should be installed by a registered electrician and in accordance with local regulations We recommend that the rail is installed onto a flat uniform wall at least 600mm from the floor and with a 300 mm clearance from permanent fixtures and where possible screwed into studs or other suitable drywall anchors If fixing to hollow cavity walls suitable anchors should be used Tools required excluding electrical connection NS thermoral HEATED TOWEL RAIL For Concealed Wiring 1 Mount the two legs that do not have holes at the curved end onto the rail first To do this remove the mounting bracket from the leg by loosening the grub screw using the allen key provided Then screw through the centre of th
3. e and you need to connect the lead to the rail lead making sure you line it up correctly and tighten the connection 5 The 4t leg then slides over the cable and connection and secures to the rail with the screw already attached to the rail The lead passes through the hole in the end of the leg and the black grommet protects the cable from any damage 6 Hold the rail in position and mark the wall where the legs will be and then hold the mounting brackets in the centre of this and drill holes for your anchor which will vary depending on the wall type you are screwing into For ease of drilling hard tiles we recommend using Thermodrill Screw the 3 mounting brackets for the legs without the lead and the angle bracket for the leg with the lead to the wall making sure they are tight and secure 7 The rail is now fitted over the brackets on the wall and tightened up using the grub screws Do not over tighten the grub screws 8 Now the lead can be plugged into a power point We recommend a timer is used to prolong the element life and to conserve power A range of timers are available from your stockist or by contacting Thermogroup on 1300368631 You will be left with the following parts 1 spare leg with black grommet 1 plastic spacer 1 metal mounting bracket Flat round bracket Cable conine ction cable Screwl Foal Black grommet if Leg Towel Rail T Cable to power point Legs for Exposed Wiring Completed Installation Wiring Wall
4. e leg into the rail at the non powered end using the two machine screws provided 2 Now select which side wiring you require left or right 3 Mount the third leg with the mounting bracket in it onto the side of the rail that will not have the wiring and secure it to the rail using the screws already mounted on the rail Do the same with the leg that will have the wire through it 4 Hold the rail in position and mark the wall where the legs will be and then hold the mounting brackets in the centre of this and drill holes for your anchor which will vary depending on the wall type you are screwing into For ease of drilling hard tiles we recommend using Thermogdrill 5 Screw the 3 mounting brackets to the wall making sure they are tight and secure Feed the lead supplied with the rail through the white plastic grommet with the connection end on the large end of the grommet Then connect the lead to the rail lead making sure you line it up correctly and tighten the connection The 4 leg slides over the cable and connection and secures to the rail with the screw already attached to the rail 7 The connection lead will now need to be connected to the power supply through a wall switch or timer by a licensed electrician The plug will need to be cut off as it is not required for concealed wiring On the concealed bracket the white plastic grommet then goes into the wall to protect the cable you will need to drill a 12mm hole for this and screw it ti
5. ght If this is loose it can be glued into the wall using silicone or max bond We recommend a timer is used to prolong the element life and to conserve power A range of timers are available from your stockist or by contacting Thermogroup on 1300368631 8 The rail is now fitted over the brackets on the wall and tightened up using the grub screws Do not over tighten the grub screws You will be left with the following parts 1 spare leg with black grommet 1 plastic spacer 1 metal mounting bracket Flat round bracket Wall Plastic Spacer Allen Key Cable connection cable Sdrew To power source Towel Rai Legs for concealed wiring Wire Connection Installation Wall Mounting Bracket For Exposed Wiring 1 Mount the two legs that do not have holes at the curved end onto the rail first To do this remove the mounting bracket from the leg by loosening the grub screw using the allen key provided Then screw through the centre of the leg into the rail at the non powered end using the two machine screws provided Now select which side wiring you require left or right Mount the third leg with the mounting bracket in it onto the side of the rail that will not have the wiring and secure it to the rail using the screws already mounted on the rail 4 Feed the lead supplied with the rail through the black plastic grommet You will need to cut the grommet to slip over wire as per attached photo s Now the 4 leg slides over the cabl
6. ill replace the faulty product with a new unit of the same model or if there is no stock available of the same model as the product the manufacturer will replace the product with a new unit of a similar size No responsibility can be taken for altered dimensions and lining up of existing holes The repair service offered within the warranty period only covers the faults and problems as developed from the manufacturer s errors Any damage caused by improper use or carelessness or incorrect wiring is not covered Thermorail is not responsible for any monetary loss or injuries caused by improper use of this product ro u Thermogroup PTY Ltd ABN 65 239 653 898 Phone 1300 368 631 Fax 1300 655 532 PO BOX 822 LEETON NSW 2705 lt www thermogroup com au email sales thermogroup com au GOOD HEATING PRODUCTS
7. thermora Installation Manual Pid MEET PEL HAR Congratulations on your purchase of a Thermorail Heated Towel Rail The rail can be hard wired or plug in on either left or right hand side Please read these instructions carefully and keep them handy for future reference Thermorail Heated Towel Rails are manufactured to the following standards 1 CE Registration certificate ATS2007165 3 AS NZ 3350 1 2002 2 ATE20071008 amp ROHS Certificate AO7051606F 4 IP Rating IP45 All Thermorail Heated Towel Rails are crafted using high quality products and will provide years of service if installed and used according to the manufacturer s instructions This towel rail must be wired by a qualified electrician and must be earthed The Thermorail Heated Towel Rail is designed to work below a stabilised temperature of 60 C under towels this will depend on towel dryness and ambient temperature This product comes with a 3 or 5 year warranty depending on the model If you have a warranty complaint please contact the retailer from whom you purchased the product Thermorail will endeavour to provide a satisfactory outcome to your complaint For any other enquiries please contact the technical helpdesk on 1300 368 631 All Thermorail Heated Towel Rails must be installed in accordance with local wiring regulations and we recommend that they are installed 600mm above the floor level for hard wired models For exposed wiring a three pin plug is included to
Download Pdf Manuals
Related Search