Installation Manual
Contents
1. fle etminder lt p gt Installation Manual COPYRIGHT FLEETMINDER 2013 e This page has been left blank intentionally Publication Date August 2013 e 7 gt c gt Installation Manual Installation Manual These instructions are to be followed Step bv Step by ONLY a qualified installer ALL CONNECTIONS TO BE SOLDERED AND INSULATED 1 Before commencing installation please ensure that all the parts are in the box supplied e If all parts are not there please do not commence installation as this will mean revisiting the install more than once Parts should include 1 x Fleetminder PLATINUM NXTG unit 1 GPS GPRS combo antenna 1 Main wiring harness 1 Panic Button fleetminder Installation Manual Page 1 9 e fleetminder ME XEIE2C6IU72 2 Find a suitable location for the Device e For installation and troubleshooting the 3 LED indicators should be visible e Keeping in mind that the unit should be located as far away from other electronic devices as possible Eg Radio ECU Please note If the unit is close to the radio it may get GSM signal feedback through the stereo system e The wiring has to be close to a power supply otherwise the wires may need to be extended e 3 metre length wire is included e Suggested installation locations include under the dash but away from the stereo or the ECU or in the Boot away from speakers or any other electronic eq2. LED will stay on when there is a valid GPS fix When there is no GPS signal SS or the device is unable to get clear view of the sky the LED will be off GREEN LED Troubleshooting Please ensure that the GPS antenna gold connector is GPS connected to the gold antenna connection and that it is mounted in a suitable Indicator spot with clear view of the sky The vehicle must be outside to be able to get a GPS fix This page has been left blank intentionally Page 8 fleetminder Installation Manual e Smt a 72 gt lt c tz Installation Manual fleetminder Installation Manual Page 9 9 e fleetminder MESCIE02C I72 FC CEA O Copyright Neltronics 2013 Specifications subject to change without Notice Page 10 fleetminder Installation Manual e
3. the gold terminals facing the circuit board Please ensure the terminals are clean and the sim card clips into place appropriately If this fails please put the sim card into a phone and make sure that it is registered and that you are able to send a message from the phone Please ensure the sim pin on the sim card has been disabled this can be done in the security settings in a mobile phone If the yellow light is on but not flashing please ensure that you have the correct APN username and password set for the network The APN is usually different for each network provider and can be found by calling the telecommunications provider some telecommunications providers require a username and password to be declared please ensure that you have these details The APN username and password can be set only from the primary defined phone number please refer to the Users Manual for setting primary identity The primary phone needs to send commands for setting the APN username and password these commands can be found in the command list in the users manual If the LED comes on solid and stays on solid for a period of about 1 2 minutes then turns off for 30 seconds before turning on again this means that the device has weak GSM signal and it is trying to acquire GPRS Please take the vehicle outdoors and check the GSM reception on any phone using the same service provider If the problem persists please try a different GSM antenna This
4. PS antenna has a clear view of the sky For GPRS tracking the LED indicator should show RED ON YELLOW FLASHING GREEN ON For testing of the unit the Primary phone number must be used using SMS Refer to the User manual for further instructions Please refer User s Manual section 8 1 12 Start tracking e On line Tracking If online tracking was ordered with the device it should already be set up to start monitoring the location Refer to your service agreement which will include your username password and the software link e SMS Tracking Refer to Command list for setting up the device using SMS Page 4 fleetminder Installation Manual e e 7 gt c Installation Manual 13 Instructions for installing the SIM card on a fleetfinder NXTG I After the device has been disconnected please press and hold the reset button for 4 seconds or until all lights on the device switch off Il Remove the back SIM cover of IIl The reset button is under the the device by removing the SIM card cover one screw as pictured below N3dO C Ns Y IV Remove the SIM card from the device The SIM card slot is pictured below iD V Insert the SIM card i
5. ion and ensure that it has a clear view of the sky fleetminder Installation Manual Page 7 e quM 4 OI z gt lt lt e fleetminder MESXEI2C6I72 Further explanation of the LED functionality is described below When the unit is powered on using main power the LED will be permanently on When the main power is cut the unit will switch to backup battery mode the LED will flash until the backup battery runs out of power RED LED Power Troubleshooting Check that you have a valid 12V or 24V source connected to Indicator the device The Red wire should be connected to the positive terminal and the Black wire should be connected to the Ground terminal If there is power applied to these wires please check the power supply by using a Voltmeter across Red and Black wires of the device If there is 12V supplied but the device is still not powering up please disconnect both wires then leave the device unplugged for 5 minutes then reconnect This process will reset the internal fuse on the device The yellow LED will flash when the device is connected to the tracking server G with a valid GPRS connection It will stay on continually when it is in sms mode YELLOW LED only or when the GSM is present but there is no connection to the server GSM GPRS Indicator Troubleshooting If the yellow light is not on at all please ensure the GSM antenna is connected and that the sim card is properly inserted with
6. n the new device VI Replace the back panel of the device securing it with the screw to maintain the dustproof standard fleetminder Installation Manual Page 5 e fleetminder Page 6 DMeEx cmc m fex OPTIONAL SOLAR BATTERY 0 GARMIN INPUT GARMIN OPTIONAL TEMP SENSOR F4 TM600 PANIC SWITCH GPS ANTENNA GSM ANTENNA WHITE INPUT 3 O 12 24V TRIGGER ORANGE OUTPUT 4 300mA BROWN INPUT 2 GND TRIGGER GREY OUTPUT 1 300mA BROWN YELLOW OUTPUT 7 300mA WHITE RED OUTPUT 6 300nA O BLACK GARMIN INTERFACE CABLE MAA YELLOW IGNITION 12 24V NOT ACCESSORIES MUST BE LIVE WHILE CRANKING BLUE OUTPUT 3 300mA GREEN OUTPUT 2 300mA PURPLE OUTPUT 5 300mA BLACK RED s 5A FUSE o 12V or 24V BATTERY RED LED POWER INDICATOR oe Z YELLOW LED GSM INDICATOR GREEN LED GPS INDICATOR OPTIONAL SENSOR INPUT fleetminder Installation Manual COIL RFID SCANNER mi Du co OPTIONAL SENSOR SPLITTER 7 gt c gt e Installation Manual LED Troubleshooting The Fleetminder NXTG ha
7. ng is required e If online tracking is required Input 1 is reserved for IGN trigger e Run the Yellow wire to an IGN trigger which has to be 12V or 24V Can be found on the ignition switch Note Use IGN wire that does not drop from 12V under crank condition 8 Connect other Inputs and Outputs to their desired triggers before connecting the Red wire to 12V or 24V Please refer to the wiring diagram for further wiring colours e The outputs are all Negative Triggers GND and are rated to 300mA max e In most cases relays will have to be used for the Outputs e Suggested Outputs Door Unlock Flash Lights Disable Starter Motor e Input 1 is Positive trigger 12V or 24V Reserved for IGN e Input 2 is Negative GND trigger fleetminder Installation Manual Page 3 e e fleetminder MgESX EIE2C672 e Input 3 is Positive trigger 12V or 24V 9 Connect the RED wire to 12V or 24V 10 Connect the Wiring harness to the device to turn the Fleetminder ON e Watch the LED s on the side of the unit to see the state of the device Please refer to the LED state explanation form for reference Note The YELLOW and Green LED s will not be on until the system goes to full working mode normally 30 seconds after power on This is in case the unit is in GPRS coverage Please refer to page 7 the LED Troubleshooting 11 To test that the device is working correctly move the vehicle outside ensuring that the G
8. s LED indicators on the front of the device that can be used for diagnosis of the device They explain the functionality of the device by their status explained below On solid state Unit powered by main power Flashing Unit operating under backup battery check vehicle iid On Off every second power supply Indicator Off There is no power to the unit check fuse and connection of the red and black wires Flashing Unit is registered on the network and connected to G the tracking server Mens p On but not flashing Unit is registered on the network but not connected Indicator via GPRS The unit is unable to connect to the server If the LED comes on solid and stays on solid for a period of about 1 2 minutes then turns off for 30seconds before turning on again this means that the device has weak GSM signal and it is trying to acquire GPRS Off Means the device is unable to register onto the network Please ensure the sim card is inserted correctly And that the sim card is valid and activated Can be checked by trialing the sim in a mobile phone In case there is a pin on the SIM card please ensure that the pin is removed this can be done when a sim card is inserted in a phone by accessing the security menu D GREEN LED GPS Indicator On Off The device is able to get a current GPS location The device is unable to get a current GPS fix Please check the antenna locat
9. uipment e Please ensure that the unit is kept away from a moist and dusty environment 3 Fit the GPS GPRS abtenna in a suitable location e Keeping in mind that the GPS antenna needs a clear view of the sky and can t be obstructed by metal e The antenna should be mounted flat side down Plastic facing upwards e A good location is far under the dash next to heater vents or on the rear parcel shelf for stealth hide the antenna e Make sure that no cables get crimped during installation e Make sure there is enough cable length to reach the unit e Connect the gold connector from the GPS antenna to the gold connector on the unit making sure it is secured Page 2 fleetminder Installation Manual e e saxis Installation Manual 4 Connect the GSM antenna to the unit e The silver connector on the unit is reserved for the GSM antenna 5 Install a suitable place for the Panic switch e In most cases the switch is located on the kick panel Please ensure the location will avoid accidental triggering 6 Run the Black wire to a good ground location e Usually the car body is an earth so a good metal bracket is suitable Test the earth is solid using a Multimeter e Make sure it does not change state when the IGN is turned on or when the lights are turned on Some vehicles change state from ground to 12V on some wires when the lights are turned on 7 Run the Yellow wire to an IGN trigger if online tracki
Download Pdf Manuals
Related Search