NX148-E LCD KEYPAD INSTALLATION MANUAL
Contents
1. 4 9 The LCD keypad is now toggled to the second language If you enter 4 9 again the keypad will revert to the first language 5 CHANGING USER CODES Note For partitioned systems someone changing the code of another person must have access to all or more partitions than the user being changed 1 Enter x 5 The LCD Screen will prompt for a code 2 Enter master code The LCD Screen will prompt for a user number 3 Enter the 2 digit applies to NX4 6 8 or The LCD screen will prompt for a new code 3 digit NX8E user number Remember to use leading zeros i e 03 or 003 for user 3 4 Enter the new user code designated for that individual The sounder will beep 3 times if it rejects the code 5 If another user code needs to be programmed return to step 3 6 To exit Code Programming press while the LCD screen is prompting for a new user number 6 ASSIGNING AUTHORITY LEVEL Note You must have authority to the partition you wish to add or remove from another person s authority Enter s 6 The LCD Screen will prompt for a code 2 Enter master code The LCD Screen will prompt for a user number 3 Enter the 2 digit applies to NX4 6 8 or The LCD will now prompt you for the first in the following list of 3 digit NX8E user number Remember attributes to use leading zeros i e 03 or 003 for user 3 PROMPTS 1 Outputs used If Prompt 1 Outputs used is If2. 21 T 33_ 5 45 f 57 o 69 _ y SL ga 22 U 34 6 46 g 58 p 70 Z 82 4 23 V 35 7 47 h 59 q t Sa ap NX148 E AMERICAN SPANISH LIBRARY ABAJO CONTACTO EXTERIOR JARDIN PRINCIPAL SOTANO ALARMA CRISTAL FACHADA LABORATORIO PUERTA TALLER ALMACEN DESPACHO FUEGO LATERAL RECEPCION TECHO ARRIBA DETECTOR GARAJE LAVABO RECIBIDOR TERRAZA AVERIA DISPARO GERENCIA MAGNETICO SABOTAJE TIENDA AZOTEA DOBLE TECHNOLOGIA GOLPE OFICINA SALA TRASERO BARRERA DORMITORIO HABITACION PANICO SALIDA VALLA CAJA FUERTE EMERGENCIA HUMO PARED SALON VENTANA CLARABOYA ENTRADA INFORMATICA PASILLO SENSOR VESTIBULO COCINA ESTACIONAMIENTO INFRARROJO PERSIANA SILENCIOSA ZONA COMEDOR ESTUDIO INTERIOR PLANTA SIRENA LOADING FACTORY DEFAULTS To load the factory defaults enter the Program Mode for the module to be defaulted using the procedure on page 2 then type 9 1 0 The keypad will beep 3 times indicating that the loading is in progress The loading takes about 6 seconds To load the factory defaults for the LCD keypad enter the Program Mode from a different keypad does not have to be LCD keypad and follow the procedures mentioned previously NOTE The two line Custom and two line Shutdown Messages will not be defaulted ENROLLING MODULES AND KEYPADS For supervision purposes the NetworX control panel has the ability to automatically find and store in its memory t
3. Cross Trip Cross Trip The first zone of a cross zone has been tripped log only event Expansion Event Expansion Event An expansion module has created an undefined event Partial Arm Partial Arm Reports a closing in the stay mode Listen In Listen In A listen in function has been activated Service Start Service End Service Start Technician is on site Service End Technician is off site Code Entry Code Entry A code has been entered First Open First Open Reports when the first partition is disarmed Last Close Last Close Reports when the last partition is armed Sprnklir Sprinkler Instant sprinkler supervisory report Clock Set Clock Set Clock has been reset RF Jammed RF Jammed A wireless expansion module is jammed CleanMe CleanMe A smoke detector requires cleaning 95 SET ELAPSED TIME IN MINUTES SINCE LAST AUTOTEST 1 Enter 9 5 2 Enter program code 3 Enter 100 s digit 10 s digit 1 s digit The LCD screen will prompt for a code The LCD will now display the elapsed time screen 97 SET SYSTEM TIME AND DATE 1 2 Enter 9 7 3 Use the up and down scroll keys to select the proper hour The LCD screen will prompt for a code Enter master code The date and time will be displayed with the current hour flashing 4 5 Enter the key to move to the minutes Repeat steps 3 amp 4 until the entire date is set 0 ADJUST KEYPAD TONE 1
4. If you see this display press 2 One or more of the following fault messages will be displayed Use the scroll keys to browse through them To exit the service messages press Service Required Type 2 for help Contro Over Current A short circuit of a control s power supply has occurred Contro Siren Trouble Open circuit has occurred on the bell or siren circuit Contro Box Tamper Optional The Box Tamper circuit has activated Contro Phone Trouble The Phone Line connected to the control is not operating properly Cont ro The control attempted to communicate a message to the Central Fail to Comm Station but was unsuccessful Contro Ground Fault A short to ground has been detected on a control circuit Contro Loss of Time Your system has lost total power and needs the clock reset 13 Contro Power Trouble Contro Low Batter Expansion Aux Comm Fail Expansion Over current Expansion Power Trouble Expansion Low Batter Expansion Box Tamper Expansion RF Jammed Expansion Trouble Expansion Siren trouble Zone Tamper Press Zone Low Battery Press Zone Lost Press zone Trouble Press The main power to your system is not on The standby battery is low An auxiliary reporting device has failed to communicate i e NX580 NX582 etc A short circuit of an expansion device s power supply has occurred The main power to an expansion power supp
5. always the case the top line will display the current location and segment number The five 5 function keys as well as the up and down arrow to the right of the display are now used to edit the message prior to saving it back to the location storage An underscore _ in the display indicates the current cursor location To move the cursor to the right press the x key To move the cursor to the left press the Cancel key To change the character at the current cursor location press the Up or Down Arrow until the desired character is displayed An alternative and possibly faster method is to enter the 2 digit number found in Table 1 1 or 1 2 which corresponds to the desired character To accept this character press the x key The character will remain and the cursor will be advanced one space to the right To insert spaces press the Stay key To delete characters press the Chime key To access the library press the Exit key Once in the library the Up and Down Arrow can now be used to scroll through the library To make a character flash press the Bypass key While in the library mode entering the flash Bypass key will cause the entire word to flash To enter the word or character being displayed enter the x key When done editing the line enter the key to escape from the edit mode Table 1 1 English No No No No
6. control the individual areas refer to the following section Operating Individual Areas in the Multi Partition Mode Operating Individual Areas in the Multi Partition Mode Enter a code that is a valid arm disarm code for the area you wish to operate The following display will appear 12 45 78 Disarm l SS FG Roe AA A Only the areas authorized by this code will appear To toggle between the armed and disarmed states on an individual area press Il Area Number To operate an individual area enter the number of the partition you wish to operate The LCD keypad will now operate as a single area keypad All keys and functions entered will affect this individual partition only The lights and LCD display represent the status of that partition only The word System will be replaced with the word Area The following is an example of this feature 12 To exit this screen press Area 5 Ready Area 5 is selected and Area 5 is ready to arm To exit the individual partition Type code to arm mode enter US Silencing Alarms in the Multi Partition Mode If the keypad is sounding an alarm or the siren is running it can be silenced by entering a code with the authority for the area s that are in alarm NOTE The EXIT BYPASS and Alarm Memory 3 function keys will only work if an individual partition is selected SERVICE DISPLAY The following message will be displayed periodically if the security system requires service
7. dim the LCD lighting Use the scroll keys Brightness option press again to adjust to desired brightness When completed exit by pressing gt 92 PROGRAMMING CUSTOM MESSAGES IN THE KEYPAD NOTES The messages custom zone and shutdown are transferred to other LCD keypads after this mode is exited All keypads must be addressed and enrolled for this to happen Set the keypad numbers with 9 4 prior to programming custom messages If a keypad is added after messages are programmed you should either program ALL messages in it or enter custom message programming on an existing keypad and make changes This is to prevent accidentally overwriting existing messages See k 9 3 option to prevent overwriting the custom message only 1 Enter amp 9 2 The LCD Screen will prompt Please Enter Your Code 2 Enter program code The LCD will now prompt you to enter message number followed by Zones 1 through 192 custom messages are message numbers 1 192 respectively Message 193 Custom message top line Message 194 Custom message bottom line Message 195 Shutdown message top line Message 196 Shutdown message bottom line 3 Enter message number The LCD will display the zone number on the top line and the description will be to edit followed by shown on the bottom line Use the instructions on page 2 for editing character data To proceed to the next location press the Police key To return to the p
8. is armed or not ready This display is reflecting all 8 areas are Ready and Area 5 is disarmed Armed 1234 678 NOTE If a number is flashing on the armed line that area is armed Instant If a number is flashing on the ready line that area is ready to be Force Armed System Ready If ALL areas are disarmed and ready to arm this display will appear on the LCD Type code to arm sereen Arming and Disarming Multiple Partitions To arm disarm multiple partitions enter a code that has arm disarm authority for ALL of the partitions to be armed disarmed The following display will appear on the LCD screen 12 45 78 Disarm The numbers on the top line represent the disarmed areas to which this code has 3 67 Arm access The numbers on the bottom line represent the areas that are armed Refer to the following table for possible conditions LCD DISPLAY FOR AREA TOP LINE OVER BOTTOM LINE CONDITION Gei Area Not Used or Authorized Blank Dash Dash Area Not Ready Flashing Dash Area Ready to Force Arm Ce Area Armed Instant Flashing Area Dash Area Disarmed amp Ready to Arm Dash To disarm all of the areas press the A up scroll key To arm all of the areas press the down scroll V key To toggle a single area between the armed and disarmed conditions press Area number For example if Area 4 is armed 4 will disarm Area 4 If Area 4 is disarmed T l 4 will arm it To
9. ten X 10 devices from each keypad 1 Enter 4 6 2 Enter the number of the device to edit 3 Press the UP scroll key to turn the device ON or press the DOWN scroll key to turn the device OFF The LCD Screen will prompt to Select Light Number 0 9 The LCD will display the light number on the left On the right side of the display it will prompt to turn the light On or Off The LCD Screen will return to the prompt to Select Light Number 0 9 4 Repeat steps 2 and 3 until all of the devices have been programmed as desired 5 Press to exit this function 47 HOUSE CODES FOR X 10 DEVICES When used in conjunction with an X 10 output device such as an NX507 E NX508 E NX534 E or NX540 E this menu allows the installer to program the specific X 10 unit and house codes for the ten X 10 devices for this keypad 1 Enter 4 7 2 Enter program code 3 Enter the X 10 unit code followed by gt 4 Enter the X 10 house code followed by The LCD Screen will prompt to Please Enter Your Code The LCD will display the Light number and Unit Code The LCD Screen will now prompt for the House Code for the device The LCD display will increment to the next Light number and prompt for its unit code 5 Repeat steps 3 and 4 until all of the devices have been programmed as desired 6 Press to exit this function 49 CHANGE LANGUAGES 1 Enter
10. the Service Message This will not allow the Service Required message to be displayed for any reason If there is a system trouble 2 will still show the Service Required menu 8 MASTER KEYPAD Enable Multi partition Mode 9 CUSTOM MESSAGE Enable Custom Message Display 10 CLOCK Enable Clock Display CUSTOM MSG LOCK Enable Custom Message Lock Prevents over writing the custom message during keypad copy SELECT AN OPTION Programs special characteristics 1 Display Press For Help 4 On suppresses beeps when an RF 2 Disable LED Extinguish on this keypad transmission is lost 3 On if PIN should be hidden when programming 5 8 RESERVED Do not program 94 SET KEYPAD NUMBER AND PARTITION 1 Enter 9 4 The LCD screen will prompt Please Enter Your Code 2 Enter program code The LCD will now prompt you for the keypad number followed by The current keypad number will be displayed in the lower right hand corner 3 Enter the keypad number followed by The LCD will now prompt you for the partition number followed by The current partition will be displayed in the lower right hand corner 4 Enter the partition number for the The keypad will automatically exit this mode now keypad KEYPAD FUNCTIONS 90 READING THE EVENT LOG The control panel has an event log that can be retrieved using a master code This log contains a listing of the last 185 events along with date time a
11. 8 while the system is disarmed will cause the control to do a callback for a download NOTE A VALID USER CODE MAY BE REQUIRED AFTER 9 8 IF ENABLED IN LOCATION 41 OF THE CONTROL PANEL Refer to the NX 4 6 8 8E Installation Manual Pressing 9 9 while the system is disarmed will cause the control to seize the phone line for a download NOTE A VALID USER CODE MAY BE REQUIRED AFTER 9 9 IF ENABLED IN LOCATION 41 OF THE CONTROL PANEL Refer to the NX 4 6 8 8E Installation Manual CHIME If enabled in the control panel entering CHIME followed by a user code will allow a walk through zone test where all zones become silent and local non reporting Each time a zone is faulted the number of the faulted zone s will be displayed on the keypad and the chime will sound It will also be entered into alarm memory and the internal log To exit at any time during this mode enter a user code Otherwise the Walk Test Mode will automatically exit after 15 minutes PARTITIONED SYSTEMS OPERATION The NX148 E can be programmed to operate all the system partitions simultaneously To set the multi partition mode use the 9 3 function and answer YES to the question Master keypad NOTE 1 followed by a code will temporarily access the Master Mode The keypad will revert back to its assigned partition 60 seconds after a keypress or 10 seconds without a keypress Press to exit this mode LIGHTS IN PA
12. NX148 E LCD KEYPAD INSTALLATION MANUAL Table of Contents ENTERING THE PROGRAM MODE 00 cccccsccccceeseseeseeeseseeeseeseceeeseeeseseeeseneaes 2 SELECTING THE MODULE TO PROGRAM c cccccessssseeeseeesseeseeeesseeseenenes 2 PROGRAMMING A LOCATION c ceccccccee secs eesneeseceeeseeesecesesneeseneseseeeseneaeseeenaas 2 NX148 E LIBRARY E 3 LOADING FACTORY DEFAULTS 0 ccccccsscssceeseseeesneessceseseeeseseseseeseseeeseeeeaes 4 ENROLLING MODULES AND KEYPAD 0 ccccccscceceee esse essen seseeseeseneeneneeees 4 PROGRAMMING THE NX148 E LCD KEYPADS cece ceeeseteeseeeeeeeeeeneeeees 4 USING THE FUNCTION MENU ooo c cee ceceeesteeseseeesneeseceseseeeseeeeseeeseeseneeesaas 4 ADJUSTING THE VIEW BRIGHTNESS OF THE LCD 5 PROGRAMMING CUSTOM MESSAGES IN THE KEYPAD ee 5 SET KEYPAD OPTIONS inr ieties n e deeg EE 6 SET KEYPAD NUMBER AND DARTITION eee cece ee eee eee eeeaeenees 7 KEYPAD FUNCTIONS cccceccecneseceeeseeseceeeseeeseaeeesneeseaeseseeeseaeseseeeseaeseseeeeaas 7 READING THE EVENT LOG ege ges edeeeEder ENEE Wine dace Nee ec 7 SET ELAPSED INCREMENTS SINCE LAST AUTOTEST ee 8 SET SYSTEM TIME AND DATE eect e ee eee cee eee ee tee eteee eee enneeetees 8 ADJUST KEYPAD TONE hetente iienaa aiaiai anii 8 VEW ZONE STATUS e deeg 9 VIEW ALARM MEMORY smana ayeo a n E 9 LIGHT CONTROL FOR X 10 DEVICES 00 cece eraser eeeaeenees 9 HOUSE CODES FOR X 10 DE NICESR 9 CHANGE LANGUAGES sidisen antie ie
13. No No No No 00 12 L 24 X 36 9 48 60 xX 72_ 84 01 Als M 25_ Y 37_ a 49 m SL y 73_ Ss _ 02 B 14 N 26 Z as b 50 n 62 Z 74 Se lt 03 C 15 O a 0 39 c 51 o 63 75 87 04 D 16 P 283 1 40 d 52 p 64 76 som 05 Eug Q 29 2 41 e 53 q ep oz Sg Z 06 Fi jis R 30 3 42 f 54 r ee 78 90 07 GJ 19 S 31 4 43 g SP S 67_ 79_ 91 os Han T 32_5 44 h Se t 68 amp S0 lt 92_ oo Tra U 33 6 ap 57_ u eg _ St 93 10 Joao V 34 7 46 j 58 vV 70 82 gt 94 11 K 23 W 35 8 47 k 59 w 71 _ Sa d 95 E NX148 E ENGLISH LIBRARY ALARM DETECTOR GARAGE LIBRARY PIR SMOKE VAULT AREA DINING GLASSBREAK LIGHT PORCH SOUND WAREHOUSE AUDIO DOOR GUEST LIVING ROOM SOUTH WEST BACK DOWN HALL MASTER RUMPUS STAIRS WINDOW BATHROOM DURESS HEAT MICROWAVE SAFE STORAGE WING BEAM EAST HOLDUP MOTION SENSOR STUDY WIRELESS BEDROOM EMERGENCY HOUSE NORTH SHOCK TAMPER YARD BUTTON EXIT INFRARED NURSERY SHOP TELEVISION ZONE CEILING EXTERIOR INSTANT OFFICE SIDE TROUBLE CLOSET FIRE INTERIOR PANIC SKYLIGHT TV DELAY FRONT JUNK PANTRY SLIDING UP DEN GAME KITCHEN PHONE SMALL UTILITY Table 1 2 American Spanish 19 L 24 W 36 8 48 i 60 r 9 84 13 M 25_ X szal 9 49 SL S 73_ SS 14 N 26 Y 38 a 50_ j 62 t 74 amp Se e is 27 Z 39 51 k 63 u fo 87 16 O 28 0 40 b 52 l 64 U 76 88 gt 17 P 29 1 41 Cc 53 m 65 77_ 839 18 Q 30 2 42 d 54 n 66 V 78 90 19 R 31 3 43 e SS 67 Ww 79_ 91 TI 20 S 32 4 44 Se o 68 xX 80 _ 92_
14. Press 0 The LCD screen will prompt you to use the scroll keys located on the right of the display to raise or lower the tone The keypad will emit a continuous tone to allow you to hear the current selection 2 Use the up scroll key to raise the tone Use the down scroll key to lower the tone 3 When the desired tone is reached press the key to set this tone and exit the mode x A VIEW ZONE STATUS 1 Enter x A 2 Use the up and down scroll keys to browse through the descriptions 3 Press to exit this function 3 VIEW ALARM MEMORY 1 Enter 3 2 Use the up and down scroll keys to browse through the alarm memory 3 Press to exit this function 44 TEST FUNCTION 1 Enter 4 4 The LCD Screen will display the zone status The LCD Screen will display the list of ALL zones in sequential order by zone number The LCD Screen will display the zone description for the zones The LCD Screen will display the list in sequential order by zone number The test will be performed as programmed If the siren test is performed enter a user code to silence the siren 45 DISPLAY TEST FUNCTION 1 Enter x 4 5 2 Press any key to end test All of the display pixels and LED indicators will flash 46 LIGHT CONTROL FOR X 10 DEVICES When used in conjunction with an X 10 output device such as an NX507 E NX508 E NX534 E or NX540 E this menu allows the user to control up to
15. Prompt 1 Outputs used is Open Close Rprt answered NO the LCD will display the answered YES the LCD will display the Bypass enable four messages below four messages below Arm Disarm 4 Enter a partition number NOTE The default allows access to all partitions The first keypress will remove access to the partition To reestablish access press the partition number again 5 Press Il when completed The LCD Screen will prompt you for the next user code 6 If another user code needs to be programmed return to Step 3 7 To exit this feature press NOTE TO INSTALLER Any master arm disarm code can add or change a user code if the master code has access to the same partitions as the code being addedichanged Consequently when programming the user codes for a partitioned system leave at least one code access to all partitions or you will not be able to add new users can be go to program code if enabled in location 43 of the control panel If you desire the end user to be able to add new codes you must remove the partition authority from all blank codes 10 7 RESET FUNCTION 1 Disarm the system 2 Enter 7 The smoke detectors zone troubles and zone tampers have now been reset If the keypad begins beeping the reset did not execute properly Enter your code to silence the keypad Wait a few 98 99 minutes and repeat step 2 to attempt another reset Pressing 9
16. REET GLADEWATER TEXAS 75647 TOLL FREE 800 727 2339 FAX 903 845 6811 www caddx com NX148 E INSTALLATION MANUAL NX148EIA00 REV A 11 10 00
17. RTITIONING MASTER MODE ARMED will illuminate if ALL partitions are armed READY will illuminate if ALL partitions are Ready The ready light will flash if all areas are Ready or Force armable FIRE will illuminate if ANY one area has a Fire condition The fire light will flash if ANY area has a Fire Trouble condition POWER will illuminate if the primary power is connected to the NX8 E control panel It will flash if the system has a low standby battery condition STAY will illuminate if ANY area has the stay light on CHIME will illuminate if ANY partition is in the Chime mode EXIT will illuminate if ANY area is timing an exit delay It will flash if ANY area is in the last 10 seconds of an exit delay BYPASS will illuminate if ANY area has a zone bypassed CANCEL will flash during an abort delay time If a code is entered followed by the CANCEL key while this light is flashing all abortable reports will stop the communication process to the central station If a code is entered followed by the CANCEL key during or after an alarm report the cancel light will illuminate and remain constant until the central station has received the cancel report SOUNDER will sound if ANY area has the sounder on This includes Entry delay Exit delay Chime and Alarm 11 DISPLAYS IN THE PARTITIONING MASTER MODE Armed and Ready Status The LCD screen will display the Armed and Ready status of ALL eight 8 partitions if any or all of the areas
18. ber s listed for that function If you already know the function numbers simply press followed by the function number NOTE Some of the functions are not listed because they are installer level functions These are samples of the displays that will appear in the Function GE SS E Menu Each time the key is pressed the next menu item will be Press for Help displayed Press the number or key to access the function desired Press the key to exit Select an Option t Zone Review The menu selections will scroll automatically The other messages are shown below For further details regarding the functions please refer to the page indicated O Set Tone Page 8 1 Master Mode 2 Service Check Page 13 3 Alarm Memory ossis Page 9 BAM eSt Page 9 45 Display Test 46 Light Control Page 9 Ac Gpanteh aaae Page 10 5 User DIN Page 10 6 User Authority 1000eeeaa Page 10 7 Detector Reset Page 11 90 Log Review Page 7 91 View Settings 0000aaaa Page 5 97 Set Datei me Page 8 CHIME Walk Test Page 11 EXIT Silent Exit 91 ADJUSTING THE VIEW BRIGHTNESS OF THE LCD 1 Enter 9 1 The LCD Screen will prompt Please Enter Your Code 2 Enter master code The LCD will now prompt you to raise or lower the viewing angle Using the scroll keys to the right of the LCD you can raise or lower the viewing angle of the text 3 To advance to the The LCD will prompt you to brighten or
19. he presence of all keypads zone expanders wireless receivers and any other module connected to the data terminal This allows these modules to be supervised by the control panel NOTE All modules should be connected and set to unique addresses prior to enrolling modules To enroll the modules enter the Program Mode of the NetworX control panel When the Program Mode is exited the control will enroll the devices The enrolling process takes about 12 seconds during which time the Service Required will be displayed Once a module is enrolled if it is not detected by the control the Service Required will be displayed PROGRAMMING THE NX148 E LCD KEYPADS This section describes how to program the address and partition of each keypad as well as the options that are available The address of the keypad is important because this is how the panel supervises the keypads The factory default for the Master Code is 1 2 3 4 when using a 4 digit code or 1 2 3 4 5 6 for a 6 digit code The factory default for the Go To Program code is 9 7 1 3 when using a 4 digit code or 9 7 1 3 0 0 for a 6 digit code USING THE FUNCTION MENU Many of the functions shown below are in the Function Menu Press to access this menu Once the x key is depressed the display will begin scrolling though a list of functions and the corresponding number s associated with those functions To access a function press the num
20. ii iade ania taaa aiaiai Eaa 10 CHANGING USER CODE 10 ASSIGNING AUTHORITY LEVEN 10 PARTITIONED SYSTEMS OPERATION cccccscsssssseesssesesneessseeeseeessseeeseneas 11 LIGHTS IN PARTITIONING MASTER MODE 0 0 ec eec eee eee eee eeee 11 DISPLAYS IN THE PARTITIONING MASTER MODE cece eee 12 SERVICE DISPLAY cscsscsscicccssncissseasccccentvceansdactiansatedatiannceaassuveceausunveoaaesutvaanen ta 13 NX148 E MAXIMUM WIRE RUN cece cece eeseee secs seseeeseaeseseeeseaeeeseenssaeeennenas 15 SYSTEM NOTES eessen edu a ege ENEE 15 SPECIFICATIONS iii irea geeeeg deed See Ed BACK ENTERING THE PROGRAM MODE To enter the Program Mode press 8 At this time the LCD screen will prompt you for the programming code Next enter the Go To Program Code FACTORY DEFAULT IS 9 7 1 3 If the Go To Program Code is valid the LCD screen will prompt you for the device address you wish to program You are now in the Program Mode and ready to select the module to program SELECTING THE MODULE TO PROGRAM Since all modules connected to the NX8 E are programmed through the keypad the module you are programming should be the first entry To program the NX8 E Control Panel enter 0 The 0 is the module number of the control and the is the entry key Other module entry numbers can be found in their corresponding manuals PROGRAMMING A LOCATION Once the number of the module to be programmed has been entered the LCD screen will prompt yo
21. ly is not on An expansion power supply has a low battery A box containing an expansion device has been opened A radio receiver is being jammed An expansion device or keypad is not reporting to the control panel An expansion device has detected some form of trouble on the bell or siren circuit A zone is tampered Press to identify the tampered zone A wireless device has a low battery Press to identify the zone A wireless or multiplexed zone device is not reporting to the control Press to identify the zone A zone is experiencing some form of trouble probably wiring Press to identify the zone 14 The following chart provides the device numbers that will be reported for trouble conditions KEYPAD PARTITION 7 1 3 4 5 6 8 200 208 216 224 6 232 po 240 24 242 243 244 245 246 8 248 NX148 E MAXIMUM WIRE RUN Note These numbers are for one keypad at the end of the wire When connecting more than one keypad to the end of the wire a heavier gauge wire will be required WHEN CONNECTED TO NX8 E WHEN CONNECTED TO NX 320 SYSTEM NOTES 15 SPECIFICATIONS OPERATING POWER OPERATING TEMPERATURE CURRENT DRAW LCD KEYPAD DIMENSIONS SHIPPING WEIGHT 12 VDC Regulated Supplied by NX8 E or NX 320 32 to 120 degrees F 110 mA Maximum 75 mA without Sounder 6 4 Wide 5 3 High 1 0 Deep 2 Ibs CADDX CONTROLS INC 1420 NORTH MAIN ST
22. nd partition where the event occurred 1 Press amp 9 0 The LCD screen will prompt you for a code 2 Enter master code The LCD screen will now show the most recent event 3 To view the events from most recent to the oldest press the down scroll key 4 To view the events from the oldest to the newest press the up scroll key The display contains the following information Event Open 75 User or Zone ID Date 19 25 17 57 P3 Indicates partition and indicates Month Date an event not reported 2 Time shown in 24 hour format This screen shows an opening of Partition 3 on September 25 at 5 27 p m by user 75 The shows that this event is not programmed to be reported to the central monitoring station POSSIBLE LOG MESSAGES DISPLAY DESCRIPTION TXlobat Transmitter Low Battery The transmitter has a low battery ZN Lost Zone Lost A wireless or multiplexed zone device is not reporting to the control Duress Duress The control has been armed or disarmed with a Duress code Man Fire Manual Fire Keypad Fire has been activated Aux 2 Auxiliary 2 Keypad Medical has been activated Panic Panic Keypad Panic has been activated KP Tamper Keypad Tamper The keypad tamper has been activated BoxTamp Box Tamper The box tamper circuit has been activated AC Fail AC Fail AC failure has been detected OverCur Over Current A short circuit of a power supply has occurred Srn Tamp Siren Tam
23. per A siren or speaker tamper has been detected Tel Fit Telephone Fault A telephone fault or tamper has been detected Exp Trb Expansion Trouble An expansion device or keypad is not reporting to the control Log Full Log Full The event log is full Open Open Reports user number date time and partition of opening Close Close Reports user number date time and partition of closing Exit Err Exit Error Entry Exit zone was faulted at the instant the exit delay expired Rec Close Recent Close An alarm occurred within 5 minutes after the control was armed Autotest Auto Test Sending a communicator test at a specified interval Start Prog Start Programming Local programming is started 7 End Prog End Programming Local programming is ended Start Dnid Start Download Download session is started End Dnid End Download Download session is ended Cancel Cancel System is disarmed Cancel was initiated within 5 minutes of an alarm Gnd Fit Ground Fault A short to ground has been detected Man Test Manual Test Bell and or communicator test while system is in disarmed condition Re exit Re Exit The exit delay has been re started without disarming the system Output Trip Output Trip A trip has occurred on an expander auxiliary output Data Lost Data Lost Communication of a signal has failed log only event Walk test Walk Test A zone Walk Test mode has been activated End Test End Test Test has been ended
24. revious location press the Fire key To re enter the last location press the Auxiliary key 4 When completed exit by pressing EXIT while the LCD screen is prompting for a zone message Any changes will automatically be copied to all other LCD keypads in the system NOTE If you desire an LCD keypad to have a different custom message you must enable Custom Message Lock under the 9 3 function For custom messages in the second lanquage NOTE The above 9 2 mode must be exited prior to changing languages 1 Enter 4 9 The keypad is now toggled to the second language 2 Enter 9 2 The LCD Screen will prompt Please Enter Your Code 3 Enter program code The LCD will now prompt you to enter message number followed by Zones 1 through 192 custom messages are message numbers 1 192 respectively Message 193 Custom message top line Message 194 Custom message bottom line Message 195 Shutdown message top line Message 196 Shutdown message bottom line 4 Enter message number The LCD will display the zone number on the top line and the description will be to edit followed by shown on the bottom line Use the instructions on page 2 for editing character data To proceed to the next location press the Police key To return to the previous location press the Fire key To re enter the last location press the Auxiliary key 5 When completed exit by pressing EXIT while
25. splay will show the current location number on the left and the segment number on the right The data will be displayed on the bottom line with the numbers 1 8 in the first 8 characters If the number appears this binary switch is on If a minus sign appears where the number should be this switch is off Toggle numbers on or off using the corresponding number digit 1 to toggle 1 8 to toggle 8 When the numbers are in the desired state enter the key The data will be entered and the segment will be incremented by 1 The data for this segment will now be displayed Continue this process until the last segment is programmed When the last segment is reached the keypad will prompt you for the next location If you wish to exit this location before the last segment is reached press the key This keypress will not save the changes made to current segment but will exit the location To proceed to the next location press the Police key To return to the previous location press the Fire key To re enter the last location press the Auxiliary key e CHARACTER DATA Character Data is used to enter LCD text when programming See 9 2 feature for custom messages page 4 Custom zone descriptions and messages are stored character or ASCII data type This information is programmed using the bottom line of the display as a text editor Once a character location has been entered the current data will be displayed on the bottom line As is
26. the LCD screen is prompting for a zone message Any changes will automatically be copied to all other LCD keypads in the system NOTE If you desire an LCD keypad to have a different custom message you must enable Custom Message Lock under the amp 9 3 function 93 SET KEYPAD OPTIONS 1 Enter 9 3 The LCD Screen will prompt Please Enter Your Code 2 Enter program code The LCD will now prompt you through the options listed on the following chart The current state of the option will be shown in the lower right corner of the display Press to advance to the next option without making changes Otherwise follow the directions on the bottom line to select the desired option This will also advance to the next option KEYPAD FEATURES 1 NOTUSED ES SILENT KEYPAD Enable Silent Keypad Option If enabled only the entry exit and sounder chime are silenced DING DONG CHIME Enable Ding Dong Sound for Chime If off chime will be a single tone Refer to NX8 E Installation manual location 40 5 SEC SILENCE Enable Keypress Silence Option Silences the pulsing keypad sounder for 5 seconds when a key is pressed ARMED ZONE INFO Enable Armed Zone Information If on the LCD keypad will display faulted or bypassed zone information when the system is armed BEEP ON PANICS Enable Panic Fire and Medical Beeptone Will sound a short beep to verify that the keypress was accepted DISABLE SERVICE Suppresses
27. u for a location number Any location can be accessed by directly entering the desired programming location followed by the pound key If the location entered is a valid location the top line of the LCD screen will display the location number on the left and the segment number on the right The bottom line of the display will show the current data This data will be displayed and entered according to the type of data used numerical binary or character data Follow the instructions below for each type of data e NUMERICAL DATA The top line of the display will show the current location number on the left and the segment number on the right The data will be displayed on the bottom line The hex equivalent will be shown in parenthesis To change the data in the current location enter the number followed by Jak The data will be entered and the segment will be incremented by 1 The data for this segment will now be displayed Continue this process until the last segment is programmed When the last segment is reached the keypad will prompt you for the next location If you wish to exit this location before the last segment is reached press the key This keypress will not save the changes made to current segment but will exit the location To proceed to the next location press the Police key To return to the previous location press the Fire key To re enter the last location press the Auxiliary key e BINARY DATA The top line of the di
Download Pdf Manuals
Related Search