SWING GATE INSTALLATION MANUAL AUTOMATIC
Contents
1. Australia Pty Lid SWING GATE INSTALLATION MANUAL AUTOMATIC GENERAL The ASA range of Do It Yourself DIY gates and accessories is designed to be an easy installation for the home handyman Please consider that the information contained in this manual is general in nature and different site conditions will require some departure from the methods used here PLANNING AND SETUP This part is essential for a good result and plenty of time should be put into making sure and double checking measurements Pen and paper are essential as is a good tape measure and a second head and someone to hold the end of the tape would not go astray There are many setup methods available too many to cover here although in most cases existing site conditions will normally dictate which method you use The important part here is that first we need to understand the entire width allowing for gates hinges and posts This can be relatively simple if you only have a set of double gates as we have already worked it out for you but if you intend to install a side pedestrian gate or fixed panel or perhaps both life gets a little more complicated Let s start however with a set of double gates with each gate being 1500 wide We need to allow for the width taken by two gates two hinges and two posts plus allow for a clearance gap in the middle GATES 2x1500 3000mm HINGES 2x30 60mm POSTS 2x100 200mm CLEARANCE 1x20 20mm TOT2. transformer FS1 F53 011 i T a e si 12345878810 A ew tenes e n rogans mote MANDO Batten fuse 104 Fast E Jumper 2 Battery charger Sign alling LEC Services fuse Slow E 6 lain na x C E JAumper P1 P d z E B B cjg x Ydc Output selection n p J1 J2 J3 12 34551852310 t 3456 10 12 2455 8 LL EN EN RR ERE ERE RI E ELECTRIC LOGH 25 BLINKER u j z J Sz Bd d A ki m o O m m OF d a a D Q 0 0 Je E ium l a x F A OUTPUT AE TE 4 2 of a isis BEC E gg 20 Jani d Y JE CONFORMITY DECLARATION To EMC directive EN45014 and 1SO guide 22 Description of the appliance Electronic board for the control of 1 or 2 low voltage motors for gate automation Model CTR50 Reference rules applied EN 50081 1 EN 50082 1 EN 55014 Basic rules applied EN 61000 6 3 A11 2004 EN 61000 6 1 EN 301 489 1 EN 301 489 3 EN300 220 2 EN 300 220 1 Test laboratory NEMKO SPA Outcome Positive The manufacturer declares that the above listed products comply to the norms on electromagnetic com
3. Yes NC Photocell Input Two NC Electric Lock Yes 12Vdc 1 slow Speed Regulator Yes IMPORTANT READ THIS FIRST Parts of these instructions are intended as a quick start guide and should be used in conjunction with the full instructions The quick start instructions provide the basics to get you up and running and are based on the most commonly used installations in Australia All electrical work in this country is tobe performed by licensed electrical contractors Electricity can kill SAFETY This booklet will offer you information you may need to install your gear motor and to safeguard your safety However caution is unquestionably indispensable and nothing is better than preventing accidents WARNING any repair or adjustment of working machinery is strictly prohibited unless all the necessary precautions electrical supply disconnected and motor off have been taken in order to avoid possible accidents WARNING any repair must be carried out by qualified people WARNING All moving mechanisms must be provided with suitable protections WARNING Keep the automatic controls out of the reach of children WARNING Command pulses must be given from positions where the gate is visible WARNING Use transmitters only if you can see the gate Read carefully the instructions enclosed in this manual Keep this booklet in a suitable place well known to all interested people PRELIMINARY CHECKS In order to make the automation
4. Connection of the devices Motor 1 Terminals 5 and 6 on J1 Motor 2 Terminals 7 and 8 on J1 Blinker Terminals 3 and 4 on J1 Electric lock Terminals 9 and 10 on J1 Photo cells power supply Terminals 1 and 2 on J1 NC photo cell contact Terminals 4 and 6 on J2 NC stop push button Terminals 4 and 5 on J2 NC photostop contact Terminals 7 and 8 on J2 NO start push button Terminals 1 and 3 on J2 NO pedestrian start push button Terminals 1 and 2 on J2 Aerial Terminals 1 and 2 J5 Open gate lamp Terminals 9 e 10 on J1 NC Motor 1 opening limit switch contact Terminals 1 and 4 on J3 NC Motor 1 closing limit switch contact Terminals 2 and 4 on J3 NC Motor 2 opening limit switch contact Terminals 5 and 8 on J3 NC Motor 2 closing limit switch contact Terminals 6 and 8 on J3 Motor 1 Encoder connection Terminals 3 and 4 on J3 Motor 2 Encoder connections Terminals 7 and 8 J3 IMPORTANT If no cable is connected to the FC1A and FC1C inputs the control of Motor 1 limit switches will be automatically disabled If no cable is connected to the FC2A and FC2C inputs the control of Motor 2 limit switches will be automatically disabled 18 CONNECTING A SINGLE SET OF SAFETY BEAMS WNO2 CONNECTING TWO SETS OF SAFETY BEAMS WOOD li O ON o2 gl 19 CTRSO General diagram AC IH Programming keys Battery
5. end of the two work times or after the Limit switches have operated for both motors the gate stops The pause period starts At the end of the pause period the gate closes automatically The operating cycle is complete only when the closing motion has ended If a start command is supplied before the end of travel is reached the gate stops A new start command will cause the gate to reverse its motion If a start command is supplied during the pause period the operating cycle is interrupted and the gate does not close automatically A further start command will determine a closing cycle Apartment mode After the power is supplied to the electronic card the first start command determines an opening cycle During the slow down phase at the end of the two work times or after the Limit switches have operated for both motors the gate stops The pause period starts At the end of the pause period the gate closes automatically The operating cycle is complete only when the closing motion has ended If a start command is supplied while the gate opens the command will have no effect If a start command is supplied while the gate closes the gate will stop and reverse its motion after approx 1 5 sec If a start command is supplied during the pause period the period will be reset and the automatic closure will start later Important If the gate opening is controlled by a clock the apartment mode must be enabled Single wing mode This mode is employed wit
6. You can now pour batches of 150mm concrete checking your post for square level and correct height as you go and prodding your concrete with a stick to get rid of air pockets When your hole is full clean off the area suitably and check again position height square and level of your post NOTES ON CONCRETE We do not recommend any type of quick dry or rapid set concrete There are however many good premix packs of normal concrete mix with aggregate available at the hardware stores Concrete may cure in as little as 12 hours in hot conditions but true full strength is not attained for up to a month In general terms your posts should be ready to hang gates from in four to seven days We would strongly suggest that you allow at least four days for concrete to set sufficiently before hanging your gates 150mm HANGING GATES Decide on a position for the hinges on your gates Try to keep the hinges close to the top bottom of your gate as this will put them in best position structurally When you have decided the position mark the spots on your posts allowing for the clearance gap under your gates Using the Tek screws supplied fix the large part of the hinge to the post Be careful not to use high torque settings that strip the Tek screw when tightening If you do you will need to either move the position or change the fastener FIT TO POST FIRST FIT TO GATE SECOND When all of your post hinges are fitted you are ready to hang yo
7. danger for the gate s motion Motor 1 Outputs for the opening closure control of the motor which drives the first gate wing during the closing phase Motor 2 Outputs for the opening closure control of the motor which drives the gate wing delayed during the closing phase This wing can be connected with an electric lock Electric lock Impulse control for the electric lock release The output can also control an open gate signalling lamp DEFINITIONS OF POWER SUPPLY INPUTS OUTPUTS AC IN FS3 FS4 12Vac input for the electronic board power supply 12Vdc OUT Pay attention to the position of the Jumper JP1 Power supply output for the photo cells and or any other accessory devices BATT IN FS1 FS2 Input for a 12Vdc backup battery connection Attention Set up the jumper JP2 in the right position in order to avoid damages of the equipment and or battery DEFINITION OF ACCESSORY INPUTS OUTPUTS Antenna Input for the connection of an antenna This input can only be used if a radio receiver card is connected to the unit 2nd radio channel Auxiliary control output To be used only if a two channel radio receiver card is connected to the unit J6 connector 11 DEFINITION OF OPTICAL SIGNALS DL1 Programming led red It is lit in the programming phase and during the gate s motion DL2 Mains power led green It is lit when the 12Vac voltage is present to the AC IN input DL3 Pedestrian start led green It i
8. power is supplied to the electronic card and the motors by means of an electric transformer fitted with a protection fuse The appliance may be connected to an optional backup battery 12Vdc 7 Ah for the automation system to work in case of absence of mains power supply Radio Receiver The electronic unit contains a two channel radio receiver allowing remote control of the gate by means of the radio transmitter The radio receiver channel 1 acts as Start control and channel 2 acts as Pedestrian start The radio receiver operates with a self learning logic and can store up to 50 different codes from the remote controls Each code may be addressed on the desired channel start or pedestrian start The memory content is preserved in absence of power supply The memory contents may be erased total cancellation In alternative the electronic unit is equipped for the optional connection of an accessory radio receiver card J6 connector The channel 1 of the radio receiver card ends with a non polarized electric contact relay directly connected to the start input The channel 2 of the radio receiver card ends with a non polarized electric contact relay directly connected to the 2nd radio channel output Work Time The motors work time is controlled by two independent digital timers If any command interrupts the wing s travel before its end the timer stops and the elapsed time is stored in memory Therefore the unit can determine with a fair approxima
9. released only after the wing has started its opening motion The extra push procedure is enabled only during the closing slow down phase near at the end of the wings travel It consists of a short acceleration of both wings approx 1 sec to help the electric lock s insertion M1 delay at opening The unit causes a fixed delay of approx 2 seconds between the first wing s M2 and the second wing s M1 start during the gate s opening phase This delay is imposed irrespective of the position from which the gate starts to open This delay may be cancelled by setting the dip switch 5 ON Blinker The electronic card supplies an on off control flashing light to the lamp The logic of the blinking allows displaying the gate s operating Quick flashing light signals the opening phase Slow flashing light signals the closing phase Fixed light signals that the gate is blocked in wait that the obstacle that covers the photocell or photostop to be removed The device supplies an on off control flashing light to the lamp for approx 1 sec before the motors start pre alarm Important In case of absence of power supply with the backup Battery connected to the card the blinker flashes every 4 sec in opening and closing cycle 14 OPERATION MODES Introduction The electronic unit contains a micro processor to control the gate s operation modes These are the four main operation phases Phase preceding the gate s motion Gate s fast mo
10. 00mm Can be cut to any size required 100mm Square Posts 100mm 50mm Square Posts 50mm 180Degree Adjustable Hinges 30mm Adjustable from 22mm to 38mm Multifit Hinges 20mm Pedestrian Gates Only Now you know your total width your post positions and how you will fix your posts you are ready for some real work POST INSTALLATION GENERAL There are quite a few variables when it comes to ways to fix posts but we will basically suggest that you will either bolt to an existing structure wall brick piers etc or concrete your post into the ground or sometimes both Either way before you start you need to survey your site for rises and falls and establish the high point in your site In an ideal situation the site will be perfectly flat and level but experience tells me that there are not many of these You need to consider the entire total width and opening arc area to ensure that your gate can swing freely to a full 90 degrees in most cases CONSIDER THIS ENTIRE AREA BEHHBENENHENEEHENEEHEHEEHNNSISESSNS Now that you understand your high point you can install your first post at approximately 1530mm to the top of the post from your high point Why approximately and why 1530mm Because there are no hard and fast rules here Your gate is 1500mm high and you need to allow a clearance gap We use 30mm as it enables us to keep our centre stop nice and low but 50mm is fine and you can get away with 5mm if it suits The point is that you mu
11. AL WIDTH 3280mm Simple enough and if the gates were the 2000mm models then our total width would be 4280mm But what happens if we add on a pedestrian gate to one side with hinges and clearance gap a fixed panel to the other side and two more 100mm posts GATES 2x1500 3000mm HINGES 2x30 60mm POSTS 2x100 200mm CLEARANCE 1x20 20mm PEDESTRAIN GATE 1 1000 1000mm HINGES 1x30 30mm PANEL CUT TO SUIT 1x1030 1030mm POSTS 2x100 200mm TOTAL WIDTH 5540mm Basic maths really So long as you know the width of each of your components and you include all components you should get your total width Once you know your total width you can relate it to your site existing structures if any and will be able to determine post positions and therefore post installation style Listed below are all of the widths associated with our standard provided components If you substitute any of these components you will need to measure and make allowance for such components IMPORTANT Provided product particularly gates can vary slightly from gate to gate Because we have clearance gaps and adjustable hinges in some cases we can quite easily handle a few millimetres here and there but if every component in our total width was 5mm oversize then we could have a tight squeeze Check the widths of your gates and posts in particular for accuracy Standard Gate 1500mm Wide Gate 2000mm Pedestrian Gate 1000mm Full Fixed Panel 24
12. K INSTALL GATE BRACKET With your post bracket securely fastened attach your gear motor to the post bracket with the bolts provided Take care to support the weight of the gear motor at this point and throughout this stage Wind out shaft D all the way till the end Now turn shaft D back one complete turn of 360 degrees Attach your gate bracket to the shaft end and position on the gate taking careful note of your 12mm fall from the post bracket Fix your gate bracket at this position Using your manual override key put the gear motor into manual mode and gently move your gate and gear motor through the entire 90 degree arc to test the smoothness of your installation If your gate and gear motor moves smoothly through the entire travel range then you are ready to proceed to the next point If you are having difficulty or hitting sticking points at any point in the travel you may need to adjust your post bracket pivot point to facilitate a smoother run INSTALL GATE STOPS This is a critical point in ensuring long trouble free operation of your automation system yet it is relatively simple Each gate must have a positive and well secured opening stop and closing stop There are a range of stops available over the counter or you can make them yourself but the critical point is that the stops must be well secured as the gear motors will exert quite a deal of force on them during programming In summary when your gate s open they must hit a positiv
13. Relays contacts capacity 20 A max Electric lock power supply 12 24 Vdc 15W max Motor power supply 12 24 Vdc 100W max total Radio receiver power supply J6 12 Vdc 2W max Accessories power supply 13 5Vdc or 24Vdc 3W max Operating temperature range 0 to 60 C internal 2 d radio channel relay contact characteristic 24 Vac 0 5 A max Motors work time programmable 1 to 120 sec Pause time programmable 1 to 120 sec 2 d wing closing delay programmable 0 to 120 sec Amperometric Stop Automatic Caution The unit must be not switched on if the connected loads or the power supply exceed the limits Failure to observe this precaution can result in damage to persons animals or objects for which the manufacturer cannot be held responsible ELECTRICAL CONNECTIONS 7 electric connectors are fitted to the card 1 J2 10 pole removable terminal board for the connection of the commands and safety devices 2 J6 10 pole connector for the optional connection of a radio receiver card 3 J5 2 pole Terminal board for the connection of the aerial cable 4 J1 10 pole removable terminal board for the connection of the power devices 5 J3 8 pole removable terminal board for the connection of the limit switches and or Encoder 6 FS1 FS2 nr 2 Faston terminals for the connection of a Backup battery T FS3 FS4 nr 2 Faston terminals for connection of the power supply transformer Terminal board J2 Terminal1 Common terminal for all
14. T CAN STILL BE EFFECTIVE Make contact with the store of purchase Branch staffs are typically not technicians and dependent on their length of service will have varying degrees of technical knowledge If they cannot help however they will certainly either source help locally from their technicians or make contact with the service technicians on your behalf OPTION 3 SERVICE CALL WITH AUTOMATIC SOLUTIONS TECHNICIAN SLOWEST METHOD If you fall within the local branch service area it may be possible to book a local technician to look at your installation Wait times will vary dependent on local workloads The cost is a service fee which includes the first half hour and the hourly rate thereafter If any Automatic Solutions provided parts are found to be defective and within warranty these will be provided free of charge NOTE If you suspect that any parts are defective and within warranty you may wish to consider option 4 A note on this option If you decide on this option you will be asked to sign an authorisation to proceed which will provide legal authority and payment security This form has three options available of which only the first two are available to you The third option is for warranty repairs only for full install customers Self install customers requiring warranty only service need to refer to option four below IMPORTANT IN SHORT THIS OPTION WILL INCUR CHARGES OPTION 4 RETURN THE PRODUCT IF BELIEVED TO BE FAULTY As a sel
15. TENNA WIRE If you intend using a full antenna install this now into the antenna terminals taking care not to allow the shield to make any contact with the core of your coaxial Otherwise cut a small length 150mm of light cable and strip one end Place the stripped end into the right hand antenna terminal and secure SET YOUR DIP SWITCHES AND JUMPERS Set your dip switches as per the settings below Single Gate Initial Settings ON J OFF 1 27 14 1516 1 8 9 Double Gate Initial Settings ON W lhe gt OFF 1 2 5 689 9 Ensure that jumper JP 1 the clip is installed to cover the 12 Volt pins and the same thing on jumper JP2 CONNECT BATTERY If you are using backup battery you will need to make two leads with male spade connectors at each end and connect your battery to FS1 and FS2 on the board Pay attention to polarity positive to positive and negative to negative CONNECT POWER You can now plug your logic control board into the 240 volt power outlet or have your electrician connect your power via a suitably installed isolation switch and turn your power on PROGRAM YOUR TRANSMITTERS REMOTES To proceed to the next step you need to have programmed a remote control transmitter into the control board To program a transmitter press P1 once on the control board and wait for the led DL1 to light Press the button channel on your remote control transmitter that yo
16. ause time DEFINITIONS OF PROTECTION FUSES F2 Battery fuse 10A Fast It disconnects the backup battery from the electronic card in case of short circuit or electric current consumption anomalies F1 Services fuse 1A Slow It protects the electronic unit in case of short circuits or overcurrents on photo cells or any other accessory devices connected to the card 12 DEFINITION OF DIP SWITCH SETTINGS Step by step Mode Dip switches 1 and 2 OFF In step by step mode a single command via transmitter or a momentary switch connected to the OSC input will cause the gate to open If no other command is issued and at the end of the slow down phase the gate will stop the operating cycle is complete and the gate waits for a further command to close If a command is made before the end of any opening or closing cycle the gate will stop A new command will cause the reversal of the motion Automatic Mode Dip switch 1 OFF and dip switch 2 ON In automatic mode a single command via transmitter or a momentary switch connected to the OSC input will cause the gate to open If no other command is issued and at the end of the slow down phase the gate will stop the pause period starts and when concluded the gate closes automatically When the gate is closed the operating cycle is complete and the gate waits for a further command If a command is made before the end of any part of the opening or closing cycle the gate will stop A new comma
17. e stop point that stop the gate s from opening any further and the same at the closed point K50 LOGIC CONTROL BOARD INSTALLATION m m JP 1 TT ITITI G0 LH 2 5 5 d Q BOARD INTERFACE COMPONENTS FS1 2 FS3 4 F1 F2 JP1 JP2 DL1 DL2 DL3 DL4 DL5 DL6 DL7 DL8 DL9 DL10 DL11 J3 J2 RV1 051 P1 P2 P3 Battery charge plug 12 24 Vdc Power supply input 12 20 Vac Battery Fuse 10A Fast Output Fuse 2A Slow Battery Charge Selector 12 24Vdc Output Selector 12 24Vdc Programming LED Power Supply LED Open Input LED Stop amp Photo LED Motor1 Limit Switch LED Motor2 Limit Switch LED Antenna Connector External receiver connector Slowing speed regulator Setting Up Dip Switches Radio code programming button Working time programming button Pause time programming button 4 11 THREE LOOPS REQUIRED FOR INITIAL PROGRAMMING TERMINALS LEFT TO RIGHT 12Vdc 24Vac LAMP MOT2 LOCK COM Choose via jumper JP2 Pos 1 amp 2 12V Flashing light output Output for motor 1 10A Max Output for motor 2 10A Max Output for electric lock 12Vdc 1A Common for open inputs PED amp OSC Pedestrian open input NO Open Stop Close input NO Common for STOP amp PHOTO inputs Stop input NC Photocell Input NC Photocell 2 common Photocell 2 Input NC Limit switch 1 opening input NC Limit switch 1 closing input NC Common for limit switch 1 Limit switch 2 open
18. electric contacts of commands Terminal2 Pedestrian start push button s normally open electric contact Terminal3 Start push button s normally open electric contact Terminal4 Common terminal for all electric contacts of stop push button and photo cell Terminal5 Emergency push button s normally closed electric contact stop Terminal6 Photo cell s normally closed electric contact Terminal Common terminal for the electric contact of photostop Terminal8 Photoelectric cell s normally closed electric contact photostop Terminal9 2nd radio channel s normally open electric contact output Terminal10 2nd radio channel s normally open electric contact output Important The normally closed inputs not in use must be fitted with jumpers Connector J6 Terminal1 Normally open electric contact connected to the start Terminal2 Common of the normally open electric contact connected to the start Terminal3 Normally open electric contact connected to the 2nd radio channel output Terminal4 Normally open electric contact connected to the 2nd radio channel output 5 Power supply negative common Terminal6 Power supply positive Terminal7 Power supply positive Terminal8 Power supply negative common Terminal9 Aerial input shield Terminal10 Aerial input signal 17 Terminal board J5 Terminal1 Aerial cable connection shield for radio receiver card Terminal2 Aerial cable connection si
19. f install customer who has purchased product if you believe the product to be faulty rather than an installation or site problem you have the option of returning the product for evaluation and to exercise your right to a replacement repair or refund as applicable All returned product is forwarded immediately to the service technicians for evaluation and response There are two main methods available to return product e Direct to the service centre this is the quickest method as it cuts out the branch delay e Via the branch of purchase slower because of the delay at the branch When choosing this option you need to complete a product return form This form gives you all the information on procedure involved and where to send to These are available at the branch of purchase can be emailed to you contact your branch or available here http automaticsolutions com au page warranty php
20. gnal for radio receiver card Terminal board J1 Terminal1 Power supply positive for photo cells or other devices Terminal2 Power supply negative for photo cells or other devices common Terminal3 Power supply positive for blinker Terminal4 Power supply negative for blinker common Terminal5 Motor M1 power supply Terminal6 Motor M1 power supply Terminal7 Motor M2 power supply Terminal8 Motor M2 power supply Terminal9 Power supply positive for electric lock Terminal10 Power supply negative for electric lock common Terminal board J3 Terminal1 Motor 1 opening Limit switch normally closed electric contact Terminal2 Motor 1 closing Limit switch normally closed electric contact Terminal3 Motor 1 Encoder signal input Terminal4 Common terminal for Motor 1 Limit switches and Encoder Terminal5 Motor 2 opening Limit switch normally closed electric contact Terminal6 Motor 2 closing Limit switch normally closed electric contact Terminal7 Motor 2 Encoder signal input Terminal8 Common terminal for Motor 2 Limit switches and Encoder Important The equipment only accepts a TTL or OPEN COLLECTOR input as Encoder signal TTL OPEN COLLECTOR FS1 Faston Backup battery s positive pole connection FS2 Faston Backup battery s negative pole connection FS3 Faston 12 15 20 Vac power supply from the electric transformer 54 Faston 12 15 20 Vac power supply from the electric transformer CTR50
21. h single wing gates When enabled it drives the motor M2 only The operating modes described above remain unchanged When the single wing mode is selected the dip switch 3 ON must be set Note At the beginning of each opening cycle with the gate closed the electric lock can operate in 2 modes 1 If dip switch 4 OFF the electric lock operates a split of second 0 8 sec before the first wing M2 starts and stops operating 2 seconds after the wing s start 2 if dip switch 4 ON the electric lock operates for a short time approx 1 sec closing the wing and stops operating 2 seconds after the M2 wing starts the opening The kickback procedure is usually employed to help the electric lock s release during bad weather 15 In any operation mode the safety devices cause the following effects Stop If the stop command is enabled no cycles can start and the start command will have no effect If a stop command is supplied during motion the gate will immediately stop and interrupt its operating cycle This condition will continue while the stop command is on A start command following a stop command always determines an opening cycle A stop command supplied during the pause period interrupts the operating cycle A start command subsequently supplied will start a closure cycle Photo Cell This device has effect only during the closure phase or in the pause period If an obstacle covers the photo cell during the closure phase the gate stop
22. he gate s to the fully open position Set the trimmer RV1 to about half way Press push button P2 once for few seconds until DL 1 lights and release After few seconds the logic control will make some tests and then it will self learn the working time by closing the gate The board will automatically exit this mode when complete and led DL1 will go out Use your transmitter or pushbutton to test your installation OPTION 2 Manual setting of the work times Use your transmitter and drive the gate s to the fully closed position Set the trimmer RV1 to about half way Press push button P2 once and hold until DL1 goes out approx 10 seconds After a few seconds the gate s start opening at a reduced speed During this phase use trimmer RV1 to obtain the desired slow down speed When the gate reaches fully open press P2 and release Wait a few seconds for DL1 to light Next press P2 and release as follows to register the following steps Dual Gates With Delay Single Gates or Dual Gates No delay Press 1 Motor 1 Start Press 1 Motor 2 Start Press 2 Motor 2 Start delayed Press 2 Motor 2 Slow down start Press Motor 1 Slow down start Press 3 Motor 2 Stop Wait 5 seconds after hitting travel stop Press 4 Motor 2 Slow down start Press 5 Motor 1 Stop Wait 5 seconds after hitting travel stop Press 6 Motor 2 Stop Wait 5 seconds after hitting travel stop The board will automatically exi
23. ing input NC Limit switch 2 closing input NC Common for limit switch 2 CONNECTING THE GEAR MOTORS TO THE LOGIC CONTROEEER Each gear motor comes with a flexible electrical lead attached with two cores negative and positive This lead needs to be connected to motor 2 output and in the case of dual gates also motor 1 output MOT 1 in the control board NB Motor 2 is used for single gate installations and in the case of double gates is the gate you may wish to attach an electric lock to as it opens first and closes last If the control board is positioned close enough it may be possible to connect one motor directly to the control board without joining and or extending the cable using a suitable cable gland to enter the control board enclosure In most cases it will be necessary to install electrical conduits and junction boxes to join and extend your motor cables using suitable two core cable Your Automatic Solutions store can provide the cable or a good local source is generally the large automotive accessory stores as most motor vehicles run 12 and 24 volt systems We recommend 5mm low voltage cable No cable run should exceed 10 metres without planning for voltage drop Ensure joins are protected from the weather using suitable junction boxes conduits are adequately clamped and cables are tied to avoid dragging or catching Once you have run your motor cables you should have two cores or in the case of dual gates four cores in
24. nd will cause the reversal of the motion If a command is made during the pause part of the cycle the gate will not close automatically and the gate will wait for a new command to close the gate Apartment Mode Dip switch 1 ON and dip switch 2 OFF In apartment mode a single command via transmitter or a momentary switch connected to the OSC input will cause the gate to open At the end of the slow down phase the gate will stop the pause period starts and when concluded the gate closes automatically When the gate is closed the operating cycle is complete and the gate waits for a further command If a command is made during the opening phase it has no effect If a command is made during the closing phase the gate will stop pause for approximately 1 5 seconds and reopen If a command is made during the pause part of the cycle the pause time will reset and gate closing will commence later IMPORTANT If using a time clock to control the gate then apartment mode must be selected Single Wing Mode Dip switch 3 ON In single wing mode the board drives motor 2 output only Kickback Extra Push Dip switch 4 ON If an electric lock is fitted it may be necessary to have a brief kickback to release in the opening phase or Extra Push to lock in the closing phase Wing Delay Zero Dip switch 5 ON If you have dual gates which do not overlap and do not have an electric lock then it may be desirable to have both gates
25. open and close at the same time and with no delay Turning on dip switch 5 to achieve this NB If dip 5 is on then dip three must be off Lock Output As Open Light Dip switch 6 ON It is possible to use the lock output as an open light if no lock is used Turn dip switch 6 on and the lock output can be used to turn on a light Exclude Photocell Test Dip switch 7 ON The board tests the photocell s to ensure correct operation and presence of power before every cycle To disable this test turn dip switch 7 on If you do not have photocells turn dip switch 7 on Slow Ampstop Motor 1 Dip switch 8 ON The control board will stop the gate should it hit an obstacle causing the motor to work harder and therefore increase the amp draw on the board The factory default is if the increased amp draw occurs for 0 4 of a second By turning on dip switch 8 this will increase to 1 second Slow Ampstop Motor 2 Dip switch 9 ON The control board will stop the gate should it hit an obstacle causing the motor to work harder and therefore increase the amp draw on the board The factory default is if the increased amp draw occurs for 0 4 of a second By turning on dip switch 9 this will increase to 1 second Turn On Signal LED s Dip switch 10 ON It is possible to turn all on board LED s on or off In a solar installation turn dip switch 10 OFF after programming to conserve power 13 TECHNICAL FEATURES Power supply The electric
26. patibility provided for by directives 89 336 EEC 92 31 EEC 93 68 EEC Date 24 08 2007 AUTOMATIC SOLUTIONS AUSTRALIA PTY LTD PO BOX 1034 CANNING VALE WESTERN AUSTRALIA 6970 TECHNICAL HELP service automaticsolutions com au 21 SELF INSTALL NEED TECHNICAL ASSISTANCE OPTION 1 DIRECT WITH THE SERVICE DESK QUICKEST AND MOST EFFECTIVE METHOD Submit your enquiry direct with the service desk at service automaticsolutions com au The service desk has the most experienced staff in Australia to help with your problem but they need your help Describe your problem in detail and as clearly as possible Don t forget to include a telephone number Be certain to detail which model or models of you are working with Send photos of the installation they love photos The people at the service desk are good but they are even better when they can see the installation Send photos of the overall scene so they can see the entire installation Also send photos of the wiring to the control board and any other part of the installation you think is relevant Send video if appropriate Smartphone s these days take remarkably good video in small file sizes which can be emailed in a moment If your problem needs a video to show the issue please feel free to send it NOTE THIS IS BY FAR THE FASTEST AND MOST SUCCESFUL WAY TO SOLVE YOUR PROBLEM PHOTOS AND VIDEOS ARE THE NEXT BEST THING TO BEING THERE OPTION 2 LODGE YOUR ENQUIRY LOCALLY SLOWER BU
27. s and reverses its motion after approx 1 5 sec If an obstacle covers the photo cell during the pause period the pause time is reset and the automatic closure is therefore delayed Photostop If an obstacle covers the photo cell during the gate s motion opening or closure or during the period preceding the operating cycle s start then the gate is temporarily stopped until the obstacle is removed When the obstacle is removed and the photocell is freed an opening cycle will start This does not apply when a start command determines the closing phase in step by step mode at the end of an opening cycle If an obstacle covers the photostop during the pause period the pause time is reset and the automatic closure is therefore delayed Pedestrian start The pedestrian start command operates in the same way as the other start command but in this case only the M2 wing fitted with the electric lock will be opened or closed The pedestrian start command has no effect during a start cycle and up to the end of the closing phase closed gate During a pedestrian start cycle the start command is always active and causes the start of an opening cycle for both wings 16 ELECTRICAL AND MECHANICAL SPECIFICATIONS Dimensions and weight with plastic box 186 x 283 x 112 mm 2 3 Kg Power supply transformer 230 12 15 20 Vac 100VA Battery charger capacity 0 5 A max Optional battery capacity 12 24 7 Ah Blinker power supply 12 24 Vdc 15W max
28. s lit when the pedestrian start control is operated DL4 Start led green It is lit when the start control is operated DL5 Stop led red It signals the gate s block state The led goes off when the stop control is operated emergency DL6 Photo cell led yellow It signals the optical barrier s state The led goes off when the photo cell is covered by persons or vehicles DL7 Photostop led yellow It signals the optical barrier s state The led goes off when the photo cell is covered by persons or vehicles DL8 Opening limit switch led yellow It signals the opening limit switch state for Motor 1 The led goes off when the opening limit switch is operated DL9 Closing limit switch led yellow It signals the closing limit switch state for Motor 1 The led goes off when the closing limit switch is operated DL10 Opening limit switch led yellow It signals the opening limit switch state for Motor 2 The led goes off when the opening limit switch is operated DL11 Closing limit switch led yellow It signals the closing limit switch state for Motor 2 The led goes off when the closing limit switch is operated DEFINITION OF TRIMMERS RV1 Slow down speed It defines the gate s speed during the slow down phase DEFINITIONS OF PROGRAMMING KEYS P1 Allows to insert cancel the radio command codes in the memory P2 Allows to set the motors work time and the M2 motor s closing delay time P3 Allows to set the p
29. side your logic control enclosure and the obvious question is which wire goes into the left terminal and which goes into the right terminal of the motor outputs There is no easy way of knowing and the answer is it does not matter we will find out in the next stage and make changes as required then Make sure you have no power connected to the control board and you can now connect your motor s to the outputs MOT2 and or MOT1 paying attention to which motor will be motor 2 which will open first if so programmed when dual gates overlap With single gates use motor 2 output only INSTALL YOUR INPUT LOOPS The only other wiring needed before testing your installation is to install a few loops into the NC or normally closed inputs Cut three short lengths 50mm of single core cable and strip the two ends Connect one end to the photo terminals and one end to the com terminal Do the same with the stop terminal and the These will need to be removed later if you add safety beams photocells or a stop button to your installation but for now will close the inputs and make the board operational Note Although we have stated above that we need to install loops into the normally closed inputs and you may note that the limit switch inputs are normally closed it is not necessary to install loops into these inputs The board tests these inputs for the presence of limit switches and excludes them automatically when they are not found FIT AN AN
30. st add your clearance gap to the height of your gate to determine your finished height above your high point level Once you have your first post installed you then have a level from which to install all remaining posts There are many tools you can use to get your levels with the obvious being a spirit level but others include laser beams a dumpy or if you are skilled enough the good old water level works a treat POST INSTALLATION DETAIL BOLTING TO AN EXISTING STRUCTURE We have provided brackets four per post that you can use if you choose or you can fix directly through the post itself Whatever method you choose cut your post to length use adequate fasteners of correct size and suitable for the structure you are fitting to Touch up paint has been provided to color match any exposed brackets or fasteners if you wish CONCRETE IN Dig a hole of at least 300mm diameter and minimum 800mm deep at least 100mm deeper than your in hole post length oize of hole will vary dependent on soil conditions but as a general rule depth is more important than width and you should aim for one third of the post in the ground Attach the wall fix brackets that are not being used to the base of the post by Tek screw These can be fitted indiscriminately as they will be underground in concrete and will give your post a method of gripping the concrete Using a suitable concrete mix including aggregate pour about 150mm into the hole before inserting your post
31. t the gear motors to the logic controller 14 Program and test your installation 15 Attach your safety devices and access devices one by one testing for correct operation at each point MAINTENANCE Periodically check your installation for loose or worn fastenings correct alignment and operation of your gate s and correct operation of your manual override operation Clean and keep clean all areas of the installation Remember that the motorisation has been planned in order to help you use the gate This means that it does not resolve the problems caused by an inadequate installation or by a poor upkeep of the gate ASA300 GEAR MOTORTNSTALLATION INSTALL POST BRACKET The position of the post bracket is critical to the success of your installation and attention needs to be paid to both its correct height and also its position on the post in respect to the relationship between your gate hinge pivot point and the motor pivot point on the bracket Once you have determined the general desired height of your motor position the bracket and take note of dimensions J and In a standard installation the basic aim is to get dimensions J and to be as close as possible to equal The other consideration before fixing the post bracket is that the pivot point of the post bracket A should be 12mm higher than the pivot point of the gate bracket H giving the gear motor an incline of approximately one degree
32. t this mode when complete and led DL1 will go out Use your transmitter or pushbutton to test your installation Setting the pause time Press push button P3 until the led DL1 lights Let the desired pause time pass and then press push button P3 again END OF SIMPLE SETUP If all went well you have finished simple setup On the following pages you will find some more detailed information and wiring diagrams to enhance and add to your installation 10 ADVANCED PROGRAMMING ADDING TO AND IMPROVING YOUR INSTALLATION DEFINITIONS OF SAFETY INPUTS Stop Input connected to a push button or switch placed outside the unit It is employed to cause the gate s immediate stop This control is used in an emergency situation Photo cell Input connected to an optical barrier It detects and signals the passage of persons or vehicles in the area crossed by the gate or in the nearby area Photostop Input connected to an optical barrier It detects and signals the passage of persons or vehicles in the area crossed by the gate or in the nearby area Opening Limit Switch Input connected to a switch placed outside the unit The switch operates when the gate has completed its opening phase Closing Limit Switch Input connected to a switch placed outside the unit The switch operates when the gate has completed its closing phase DEFINITIONS OF OUTPUTS Blinker Lamp s on off control The lamp functions as a warning and optical signaller of potential
33. tion the partial working time necessary for the wing to end its travel For the automation system to work properly the work time value to be set must be slightly approx 9 Sec above the wing s actual work time In this way the motor will stop even if the limit switch control has not operated We recommend to adjust the work time so that the wing starts to slow down at min 50 cm from the end of its travel The stop of the wing depends by the current consumed by the motor Torque During the normal speed phase when the motor s current reaches the self learned value the gate stops both wings in opening and then it reverses its motion for approx 2 sec while during the closure phase the gate stops and reverses its motion after approx 1 5 sec After the electric power is supplied to the electronic card at installation or after one absence of power supply when the Start push button is pressed for the first time the gate performs an opening cycle Warning In case of absence of power supply the position of the gates will be lost Timers reset and the gates first command will perform and opening manoeuvre Kickback Extra push This procedure can be enabled or excluded It is usually employed to help the electric lock insertion and release during bad weather conditions wind etc The kickback procedure consists of a logic sequence operating the electric lock with a short closure phase approx 1 sec with the gate closed The electric lock is
34. tion phase Gate s slow motion phase Gate s pause phase open gate The unit can function in three modes Step by step This mode is enabled by setting the dip switches 1 OFF 2 OFF Automatic This mode is enabled by setting the dip switches 1 OFF 2 ON Apartment This mode is enabled by setting the dip switches 1 ON 2 No effect Notice The operation logic setting dip switch the work time programming and the pause time programming must be carried out only if the cycle is concluded or before it starts with closed gate The opening and closure cycles are enabled by a Start or Pedestrian start control Important Whatever logic has been selected the first Start command after the power is supplied to the electronic card will always cause the start of an opening cycle Step by step mode After the power is supplied to the electronic card the first start command determines an opening cycle During the slow down phase at the end of the two work times or after the Limit switches have operated for both motors the gate stops The operating cycle is completed and the system waits for a new start command to determine the closing cycle If a start command is supplied when the end of travel has not been reached yet the gate stops A new start command will cause the reversal of the motion Automatic mode After the power is supplied to the electronic card the first start command determines an opening cycle During the slow down phase at the
35. u wish to use for two seconds and release Your transmitter should now be programmed Repeat for other transmitters You can also program a second button channel on any transmitter to open in pedestrian mode To program a transmitter to pedestrian opening press P1 twice and release NB Each press of P1 should be spaced by 1 second minimum when DL1 is lit press the button channel you wish to use for pedestrian access Up to 50 codes may be stored in any combination of full open or pedestrian open To erase all codes press and hold P1 until the red LED DL1 goes out about 10 seconds IMPORTANT If you are not using transmitters you will need to connect a normally open momentary pushbutton into COM and START terminals to proceed CHECK FOR CORRECT MOTOR DIRECTION This is where you find out if you were lucky enough to have got your motor output wiring in the correct terminals With your gear motor s in manual position them about half way open and lock them into automatic mode Using the transmitter you programmed press the button and release Because this is the first activation after a power interruption your gates should open Press your transmitter again to stop the gates To correct any leaf which did not open simply turn off the power disconnect the battery lead and reverse the motor terminals Apply power and test again PROGRAM THE CONTROL BOARD OPTION 1 Automatic setting of the work times Use your transmitter and drive t
36. ur gates There are a number of ways to do this If you are very accurate you can measure and mark your gate fit the hinge bracket to the gate and then assemble all the parts You might find it easier however to assemble the hinge so it is complete on the post use blocks under your gate to lift and hold it at the correct height and then fix the hinges to the gate Using this method you can also use a 30mm packer to get your gap between post and hinge accurate Once both gates are hung you can then adjust the hinges for gap and height ADJUST FOR GAP AND HEIGHT INSTALLATION OF STOPS We have provided a centre stop and two open stops which must be installed for your automation to function correctly They are designed to be bolted down but may be concreted in place by simply welding a short 250mm length of steel with a cross brace to the base ASA300 K50 IMPORTANT MANUAL OVERIDE CAP MUST BE ON AT ALL TIMES ASA300 Motor Voltage 12 volt Power Absorbed 70 watts Speed 0 019 metres per second Maximum Thrust 1500 N Protection Level IP43 Duty Cycle 90 Dimensions 670L x 90W x 185H Stroke 30 CM Maximum Leaf 3 0 metres Maximum Leaf Weight 250 Kg Opening Time 16 Seconds K50 Motor Voltage 12 24 DC Motor Inputs Two Battery Charger Inbuilt 12 24V Receiver Inbuilt or External Limit Switches Yes No Pedestrian Input Yes NO otart Input Yes NO otop Input
37. work efficiently the gate to automate must have the following characteristics It must be balanced must oscillate fluently You must be able to carry out manual closing and opening of the gate without any effort Make sure that the gate has a solid structure and that there is no friction points in its movement Make sure that the gate s have both solid opening stops and solid closing stops GENERAL ORDER OF INSTALLATION To ensure a good installation of the gear motors ASA300 we suggest the following order of installation 1 Open the box and take out gear motor Inspect the contents and ensure all components are present 2 Make sure that the leaf of the gate is perfectly horizontal 3 Determine the height position of your motor and mark post bracket position 4 Spend some time here considering the correct height and geometry of your post bracket 5 Attach the gear motor on to the support post 6 With gate s leaf closed turn and slide the screw of gear motor s shaft until it comes to the end of the screw 7 Screw shaft back 1 complete turn of 360 8 Place the gate support plate in the hole of the shaft end and position it against the gate leaf 9 Fixitto the gate leaf taking in account the inclination 10 Put the gear motor into manual operation mode with your override key and test your install for smoothness 11 If correct proceed in the same way with the other gate leaf 12 Place the mechanical limit stops 13 Connec
Download Pdf Manuals
Related Search