Home

USER'S MANUAL

1. supported by the code reader No Abbreviation Name 1 Misfire Monitor Misfire Monitor 2 Fuel System Mon Fuel System Monitor Comprehensive Components 3 Comp Component Montor EQP 103 User s Manual 42 Catalyst Mon Catalyst Monitor Htd Catalyst Heated Catalyst Monitor D Evap System Mon Evaporative System Monitor Sec Air System Secondary Air System Monitor AIC Refrig Mon Air Conditioning Refrigerant Monitor Oxygen Sens Mon Oxygen Sensor Monitor 0 Oxygen Sens Htr Oxygen Sensor Heater Monitor 11 EGR System Mon Exhaust Gas Recirculation System Monitor gt 0 IN O O NOTE Not all monitors are supported by all vehicles To retrieving I M Readiness Status data gt 1 Use the UP DOWN key to select I M Readiness from Diagnostic Menu screen DIEIS CAVE Read Codes Clear Codes Datastream Freeze Data I M Readiness O2 Monitor Test 2 Press the ENTER key to confirm V If vehicle supports both types of monitors following screen displays EQP 103 User s Manual 43 VAN Readiness Since DTCs Cleared y This Drive Cycle V Use the UP DOWN key to select a monitor type and press the ENTER key to confirm 3 Depending on readiness test one of these 2 screens will be present Since DTCs Cleared MIL Status OFF Misfire Monitor N A Fuel System Mon N A Comp Component OK Catalyst Mon N A Htd Catalyst N A This D
2. 56 e Verify ignition key is in the ON position e Make sure the code reader is correctly attached to vehicle s Data Link Connector DLC e Check DLC for cracked or recessed pins or for any substance that could prevent a good electrical connection e Check EQP 103 OBDII connector for bent or broken pins e Make sure the vehicle is OBDII EOBD compliant e Cycle the vehicle key to OFF for 10s and then back to ON e Verify battery voltage is at least 8 0V with KOEO e Verify that the control module is not defective 7 2 Code Reader Does Not Power Up If EQP 103 will not power up communicate with vehicle s control module or functions incorrectly in any other way do the following e Check DLC for broken or bent pins and clean the pins if need be e Make sure EQP 103 is correctly connected to vehicle s DLC e Verify battery voltage is at least 8 0V with KOEO 7 3 Battery Replacement EQP 103 needs a 9V cell battery to operate when disconnected from the vehicle V When the a icon appears replace the battery as instructed below To replace battery P 1 Place the code reader face down 2 Remove battery cover with a screw driver 3 Remove battery and discard according to your local rules 4 Install a new 9V alkaline battery 5 Reinstall the battery cover with the screw driver E Quality Products E 12 Month Warranty Technical Support Available from leading automotive specialists and retailers www plusquip com a
3. Menu screen Read Codes Codes a Clear Codes Datastream Freeze Data I M Readiness O2 Monitor Test 2 Press the ENTER key to confirm 3 View DTCs and their definitions EQP 103 User s Manual 28 10 1 2 P0101 Generic Mass or Volume Air Flow A Circuit Range Performance V If no DTCs are present a message stating No Pending Codes Found is displayed v If any manufacturer specific or enhanced codes detected a Manufacturer specific codes are found Press any key to select vehicle make message displays prompting you to select vehicle make before viewing DTC s V If manufacturer of the vehicle being tested is not listed select Other 4 Use the UP DOWN key to move back and forth through codes when more than one code is retrieved Use the ENTER key to move to next screen when the code definition covers more than one screen 5 Press the ENTER key to return to Diagnostic Menu screen 5 2 Clearing DTCs The Clear Codes function is used to delete DTCs and I M Readiness data from vehicle s control module s It may also erase freeze data and set monitors to incomplete or not ready V Perform Clear Codes function only after systems have been checked completely vV After servicing the vehicle erase stored DTCs and verify no codes have been reset If a DTC returns problem has not been fixed or other faults are present EQP 103 User s Manual 29 V Depending on which monitor sets a code the
4. sevens loos iwenaed 49 5 10 Modules Present iates tates peas uncercerneniebarte iene aeadoneieew neds 51 6 Updating and PFU sos sce s eeeeecas ccs eas recsesedug inom civ sdo mee dence teenies 52 6 1 Updating the Code Reader x tai scccc 2ccsets cacdennest ess deneeebsszennnsszeeeiess 53 6 2 PANINO oerna a a E E RA E 54 7A POUDIOSIOOUIG irranga era ticmaetacte whats 55 DN Eror INOS SUS rensing a seal ane tees 55 7 2 Code Reader Does Not Power UD ccesseeeeseeeeeeeeeeeees 56 7 3 Battery Replacement a scecc cords ected edie rs Sieben eddacc bdeceteieaniaies 56 EQP 103 User s Manual 2 1 Safety Information For your safety and to prevent damage to the equipment and vehicles read this manual thoroughly before operating your EQP 103 EOBD code reader The safety messages presented below and throughout this user s manual are reminders to the operator to exercise extreme care when using this device Always refer to and follow safety messages and test procedures provided by the manufacturer of the vehicle or equipment being tested Read understand and follow all safety messages and instructions in this manual 1 1 Conventions Used We provide safety messages to help prevent personal injury and equipment damage Below are signal words we used to indicate the hazard level in a condition No Signal Word Hazard Level Indicates an imminently hazardous situation which if not avoided will result 1 LA DANGER in death or
5. vehicle may need to be driven and the monitor run before concluding that the fault is repaired V This function is performed with KOEO Do not start the engine To erase codes from vehicle control modules gt 1 Use the UP DOWN key to select Clear Codes from Diagnostic Menu screen Diagnostic Menu Read Codes Clear Codes q Datastream Freeze Data I M Readiness O2 Monitor Test 2 Press the ENTER key to confirm 3 If codes and diagnostic results are to be cleared use the UP DOWN key to select YES and press the ENTER key Clear Codes Are you sure to clear codes lt Y ES gt V If codes and test data not to be deleted select NO and a Command Cancelled message displays Wait a few seconds or press any key to return to Diagnostic Menu 4 Wait a few seconds until a Codes Cleared message shows indicating codes are cleared successfully EQP 103 User s Manual 30 V If the code reader fails to clear the codes a Clear Error Turn Key on with Engine off message displays 5 Wait a few seconds or press any key to return to Diagnostic Menu 5 3 Live Datastream Viewing Data The View Data function allows real time viewing of the vehicle s electronic control unit s PID data including sensor data operation of switches solenoids and relays To view live datastream gt 1 Use the UP DOWN key to select Datastream from Diagnostic Menu screen Diagnostic Menu 9 Read Co
6. C definitions 6 To quit Code Lookup press the BACK key 4 Data Review The Review Data function is used to view test results from last vehicle tested v Depending on vehicle tested the code reader may have different types of data to review To review stored data 1 Use the UP DOWN key to select Review Data from Main Menu screen EQP 103 User s Manual 23 Diagnostics 7 Print Data Code Lookup System Setup Tool Information 2 Press the ENTER key to confirm 3 Use the UP DOWN key to scroll to the desired item and press the ENTER key Stored Codes Codes Pending Codes Datastream Freeze Data I M Readiness O2 Monitor Test V If no data from last vehicle tested is recorded only Module Present has information module ID and protocol type to be reviewed 10 1 2 P0101 Generic Mass or Volume Air Flow A Circuit Range Performance y If no data exists for function selected to review a No Data Found message displays EQP 103 User s Manual 24 5 OBDII EOBD Diagnosis Diagnostic Menu allows you to e Read DTCs e Clear DTCs View live datastream View freeze data e View I M Readiness data e O2 sensor test information e View on board monitor test results e Perform component tests e Retrieve vehicle information e Read modules ID and protocol information V The code reader detects the communication protocol when it is connected to the vehicle and uses
7. C or laptop with USB Ports and Internet Explorer USB cable V To be able to use the update tool your PC or laptop must meet the following minimum requirements e Operating System Win98 NT Win ME Win2000 Win XP VISTA or Windows 7 e CPU Intel PIII or better e RAM 64MB or better e Hard Disk Space 30MB or better e Display 800 600 pixel 16 byte true color display or better Internet Explorer 4 0 or newer IMPORTANT Do not disconnect the code reader from computer or power off the computer during the process of updating To update program 1 Download the update tool EQP 103 PC Link and update files from our website www plusquip com au download page Download and save the applications and files onto your computer disk EQP 103 PCLink Update Software Unzip the update software file Double click the exe file and follow instructions on computer screen to install the tool and driver Double click the desktop icon to launch the application Connect EQP 103 to computer with the USB cable provided and the application detects the device automatically EQP 103 User s Manual 54 6 Use lt Select File gt to locate update file downloaded Update Program 1 Connect device to computer with the USBcabie supplied 2 Click lt Select File gt to locate update file 3 Click lt Update gt to start upgrading 7 Click lt Update gt to start updating To update DTCs V It may take several minutes to update t
8. DOWN key to move up or down and press the ENTER key to select or deselect PIDs to view Selected parameters are marked with solid squares Custom Data List G A DTC_CNT MIFUELSYS1 01 lM FUELSYST2 02 MILOAD_PCT 03 E ETC F 04 E SHRTFT1 V The number to the right is the order that the PIDs were selected and will be displayed vV You are allowed to pick up a maximum of 18 PIDs If you selected more than 18 PIDs a The selected data list is full message displays on the screen 4 Hold the ENTER key for 2 seconds to view selected PIDs EQP 103 User s Manual 34 BEIEN UUN 7 ST i FUELSYS1 OL Drive FUELSYST2 N A LOAD_PCT 0 0 EGF 172 SHRTFT1 0 0 LONGFT1 0 0 V If the G icon displays while a PID is selected press the ENTER key to view graph 5 Use the BACK key to return to View Data screen Changing Measurement Unit Refer to Changing Measurement Unit on page 15 of System Setup Recording Data The Record Data function is used to record PIDs to help diagnose intermittent drivability problems that can not be determined by any other method A recording consists of 5 frames of data before trigger point and several frames after trigger V There are 2 types of trigger methods used e Manual Trigger triggers recording whenever the operator presses the ENTER key Trigger On DTCs automatically triggers recording when a code is detected by vehicle V Trigger On DTCs is not ava
9. EQDPp 102 CUWPF 1VU9 oS Ud USER S MANUAL This compact multi function tool can be used on local and imported vehicles that support the OBDII vehicle communication system EQP 103 User s Manual 1 Table of Contents T SAIOLY IN MAON oesie aerate ese 2 TiConventions USE sirere e E eee E erat 2 1 2 Important Safety Instructions ssseesseeeeee eese eener rererere errre nere 2 2 Using This AGIA s sors asns a E 4 3 NTOAUCUOMN osidento TET e 6 3 1 About OBDIVEOBD sssssssseeesnneesereereeersrrrerrnntrnnreenntnnnnrrenrennnnt 6 3 2 About the Code Reader s neeseneeeeeeneeeerreererenrrrenrrreenrrrenreree 9 4 Data FROVIOW sess seuss cee se ten ccna cn pea de peneeneancetavigvinuid a etostieiendy 22 5 OBDIVEOBD DIGG OSIS xs cove veeseesieosensanad nedoonecncseeeeenansrncemersennsine 24 Be 1 Reading DTO Sernin EO 27 5 2 Clearing sc ees de ceca eta eed kas edackavzanticeshees 28 5 3 Live DatastredMi Ree eee eee ee meee eee eee errr 30 5 4 Viewing Freeze Data xci asccainiisssaeceintovies norisinartacaeeavienbiaeudalinn 40 5 5 Reading I M Readiness Status Data 0 eeeeeeseeeeeeseeeeeeees 41 5 60 02 MORMON TeSt sscs a sarcessectaciteatansasctastecteetts na aE 44 5 7 On Board Monitor TeSt xc cscctevccectadscurtarscsanveaiteresschcesesteiactaiieedsns 45 5 8 Component Test soneesoeneeoeeeeeeeresorresrnnrrsterestnnrsenrnsnenesenn esenee 48 5 9 Reading Vehicle Information siauscease tercdtien as decan
10. a V For CAN vehicles test screen is illustrated as below EQP 103 User s Manual 47 On Board Mon Test 7 O2 Mon B1S1 Mon B1S1 gt O2 Mon B182 Catalyst Mon B1 EGR Mon Bank1 V If vehicle being tested does not support this function the code reader displays a Not Support This Function prompt 4 Use the ENTER key to view details of selected test results V For non CAN vehicles test screen is illustrated as below Test 01 Data ID MOD MEAS MAX MIN SIS O2 Mon B1S1 Rich Lean Threshd mV 0 450 0 312 0 630 OK EQP 103 User s Manual 48 V When more than one screen of data is retrieved use the UP DOWN key to view additional information 5 Press the BACK key to return to On Board Monitor Test 5 8 Component Test The Component Test allows the code reader to control operation of vehicle components tests or systems V Some manufacturers do not allow tools to control vehicle systems V The manufacturer sets the criteria to automatically stop test Refer to appropriate vehicle service manual before using this function To do component test P 1 Use the UP DOWN key to select Component Test from Diagnostic Menu screen Diagnostic Menu gt On Board Mon Test Component Test Vehicle Information Modules Present Measurement Unit 2 Press the ENTER key to confirm 3 Use the UP DOWN key to pick an available system or component EQP 103 User s Manual 49 Co
11. al and electrical fires in work area AWARNING Always be aware of rotating parts that move at high speed when an engine is running and keep a safe distance from these parts as well as other potentially moving objects to avoid serious injury AWARNING Do not touch engine components that get very hot when an engine is running to avoid severe burns AWARNING Block drive wheels before testing with engine running Put the transmission in park for automatic transmission or neutral for manual transmission And never leave a running engine unattended AWARNING Do not wear jewelry or loose fitting clothing when working on engine ACAUTION Make sure to turn off ignition before connecting or disconnecting the code reader EQP 103 User s Manual 4 2 Using This Manual We provide instructions for the usage of your code reader in this manual Below is a list of conventions we used in the manual Safety Information See Safety Information on pages 2 3 Bold Text Bold emphasis is used in procedures to highlight selectable items such as buttons and menu options Example Use the UP DOWN key to select the desired measurement unit Bold lItalic Text Bold italic text is used in the procedures to highlight the menus on the code reader screen Example Use the UP DOWN key to select Language from System Setup screen Symbols and Icons V Check Note Additional information about the subject in the preceding paragraph is introduce
12. creen displays Trigger On DTC Waiting for DTC to trigger recording BACK EXIT V If data is to be erased select YES if data is not be erased pick NO to return to Select Memory screen and pick another one 7 Press the ENTER key to start recording or wait for codes to trigger Recording 5 60 m FUELSYS1 OL Drive FUELSYST2 N A LOAD_PCT 0 0 EIGA 172 SHRTFT1 0 0 LONGFT1 0 0 V The code reader keeps saving data until e memory is full the operator presses the BACK key NOTE Different vehicles communicate at different speeds and support a different number of PIDs Therefore the maximum number of frames that can be recorded varies 8 After recording the code reader display a prompt to Playback Data EQP 103 User s Manual 38 Record Data Recording Done Playback Data lt YES gt 9 Select YES to view recorded data pick NO or press the BACK key to return to Record Data Playback Data The Playback Data is used to playback recorded PID data To playback data 1 Use the UP DOWN key to select Playback Data from Datastream screen 9 View Data l Record Data Playback Data 2 Press the ENTER key 3 Use the UP DOWN key to select a memory area that is marked with an asterisk EQP 103 User s Manual 39 Select Memory z Area 2 i Area 3 V If no recording exists the code reader displays a No Recording Found message 4 Press
13. d by a V Check Note Example V The code reader is set to display English menus by default e Solid Spot Operation tips and lists that apply to specific tool are introduced by a solid spot e Example System Setup allows you to e Select menu languages e Change measurement unit e Adjust display contrast IMPORTAN I EQP 103 User s Manual 5 indicates a situation which if not avoided may result in damage to the test equipment or vehicle Example IMPORTAN I Do not soak keypad as water might find its way into the code reader NOTE NOTE provides helpful information such as additional explanations tips and comments Example NOTE Not all data are supported by all vehicles Screens Some help messages information and data displayed on the code reader are also shown in graphical text boxes The screens presented are examples only and actual test screen may vary for each vehicle being tested Example Diagnostics Review Data Print Data Code Lookup System Setup Tool Information Arrow Icon gt An arrow icon indicates a procedure Example To change menu language gt 1 Use the UP DOWN key to select Language from System Setup screen EQP 103 User s Manual 6 3 Introduction The EQP 103 is specially designed to support all 9 OBDII service modes including live data O2 sensor test and more on OBDII EOBD compliant cars SUVs light duty truck and mini vans sold worldwid
14. d printing V Refer to Code Reader Does Not Power Up on page 56 of Troubleshooting if there are problems Internal Battery To power on the code reader by internal battery 1 Install 9V battery 2 Press the POWER key to turn on the code reader V When the icon appears refer to Battery Replacement in on page 60 of Troubleshooting to replace the battery V When powered from the battery the code reader disables the display s backlighting and turns off automatically after a period of inactivity IMPORTANT If the code reader will not be used for an extended period of time remove the battery to prevent battery leakage from damaging the battery compartment IMPORTAN I Do not use a Lithium Li battery External Power To power on the code reader by vehicle battery 1 Locate the diagnostic interface on vehicle 2 Plug in the code reader s OBDII connector to the DLC A plastic DLC cover may be found on some vehicles Remove the cover before plugging the OBD2 cable System Setup System Setup allows you to e Select menu languages e Change measurement unit e Adjust display contrast e Change auto matic power off time Turn on off beeper e Check LCD display and operation of keypad EQP 103 User s Manual 13 V System Setup settings remain until change to the existing setups are made To do system setup p 1 Press the BACK key to enter System Setup from home screen or use the UP DOWN key to select System Setup fr
15. des Clear Codes Freeze Data I M Readiness O2 Monitor Test 2 Press the ENTER key to confirm 3 Use the UP DOWN key to select View Data from Datastream screen EQP 103 User s Manual 31 View Datal A Record Data Playback Data 4 Press the ENTER key to confirm V Some vehicles may not support this function Viewing Complete List Complete Data List displays all supported PIDs of the vehicle being tested To view entire data list gt 1 Use the UP DOWN key to select Complete Data List from View Data screen Complete Data List Record Data Playback Data 2 Press the ENTER key to confirm your selection 3 View PIDs on code reader Use the UP DOWN key when more than one screen of information is retrieved EQP 103 User s Manual 32 _ P DTC_CNT 3 FUELSYS1 OL Drive FUELSYST2 N A LOAD_PCT 0 0 BICHE 172 SHRTFT1 0 0 V If the G icon shows when a PID is selected press the ENTER key to view graph And press the BACK key to return to live PID screen LOAD_PCT 50 2 i 45 2 4 Press the BACK key to return to previous level Viewing Custom Data List Custom Data List allows certain PIDs from Complete Data List to be selected To view custom data list 1 Use the UP DOWN key to select Custom Data List from View Data screen EQP 103 User s Manual 33 Complete Data List Custom Data List 7 Measurement Unit 2 Press the ENTER key 3 Use the UP
16. displayed NOTE prev ious testing is not cleared information of current test can not be stored NOTE The code reader keeps one recording ONLY If data from Review stored data completely before erasing 4 Use the UP DOWN key to select a control module where the data may be retrieved when more than one module is detected Control Module Engine q A T V To view information of another control unit quit current test and select another module vV If only one control module is equipped with the vehicle being tested the above screen is not displayed EQP 103 User s Manual 27 5 1 Reading DTCs The Read Codes function is used to read DTCs stored codes which are used to help identify the cause of a trouble or troubles with a vehicle and pending codes from the vehicle s control modules V When emission related or driveability fault occurs the control module illuminates the malfunction indicator lamp MIL V Pending Codes are also referred to as continuous monitor or maturing codes that indicate intermittent faults If the fault does not occur within a certain number of drive cycles depending on vehicle the code clears from memory If fault occurs a specific number of times the code matures into a DTC and the MIL illuminates or blinks V This function can be performed with KOEO or KOER To read codes from vehicle control modules P 1 Use the UP DOWN key to select Read Codes from Diagnostic
17. does not support this function the code reader displays a Not Support This Function message 4 Press the ENTER key to view data of selection O2 Bank1 Sensor1 81 Values 10 126 90 255 V When more than one screen of data is retrieved use the UP DOWN key to view additional information 5 Press the BACK key to return to O2 Monitor Test screen 5 7 On Board Monitor Test The On Board Monitor Test function is useful after servicing or after clearing a vehicle ECU s memory This function receives test results for emission related powertrain components and systems that are not continuously monitored for Non CAN vehicles EQP 103 User s Manual 46 For CAN vehicles it receives test data for emission related powertrain components and systems that are and are not continuously monitored It is the vehicle manufacturer who is responsible for assigning test and component IDs NOTE Test results do not necessarily indicate a faulty component or system To request vehicle information p 1 Use the UP DOWN key to select On Board Monitor Test from Diagnostic Menu screen Diagnostic Menu z On Board Mon Test 7 Component Test Vehicle Information Modules Present Measurement Unit 2 Use the ENTER key to confirm 3 Use the UP DOWN key to pick desired test results V For non CAN vehicles test screen is illustrated as below On Board Mon Test 7 Test 01 Data 01 Data Test 03 Data Test 05 Dat
18. e since 1996 3 1 About OBDII EOBD What is OBD The first generation of On Board Diagnostics or OBD was introduced in early 1980 s to control engine functions and diagnose engine problems by vehicle manufacturers As the OBDI lacked standardisation of protocols and interface it allowed different interpretations among vehicle manufacturers OBDII the second generation On Board Diagnostics improved in both capability and standardisation is a system developed in mid 1990s by the Society Automotive Engineers SAE to standardise automotive electronic diagnosis EOBD is European version of OBDII required in Europe since 2001 The OBDII standard specifies e A generic diagnostic port Data Link Connector and its pinout e The protocols and the messaging format e A standard list of vehicle parameters identifications A standard list of diagnostic trouble codes DTCs EQP 103 User s Manual Data Link Connector The Data Link Connector DLC is a standard 16 pin interface located under the dashboard on the driver s side of the passenger compartment If the DLC is not located under the dashboard as stated a decal describing its location should be attached to the dashboard in the area the DLC should have been located NOTE On some Asian and European vehicles the DLC is located behind the ashtray which must be removed to access it or on the far right corner of the dash If the DLC cannot be found consult the vehicle s s
19. ervice manual for the location 5 BEHIND A aa 7 NEAR ASHTRAY plage A OF DASH RIGHT CENTRE OF DASH EQP 103 User s Manual 8 Diagnostic Trouble Codes DTCs Diagnostic Trouble Codes DTCs are faults stored by vehicle computers when problems that affect engine performance and emissions are detected DTCs are used to help identify the cause of a trouble or troubles with a vehicle and determine the fault location s DTCs consist of a five digit alphanumeric code Please see below for the DTCs format and code types Bx Body Cx Chassis Px Powertrain FERT Ux Network Comm Specific Fault Designation x 0 1 20r3 Vehicle Specific System Example P0101 Mass or Volume Air Flow Circuit Range Performance Problem Powertrain Codes Body Codes POxxx Generic SAE BOxxx Generic SAE P1xxx Manufacturer Specific B1xxx Manufacturer Specific P2xxx Generic SAE B2xxx Manufacturer Specific P30xx P33xx Manufacturer Specific B3xxx Generic SAE P34xx P39xx Generic SAE Network Communication Codes Chassis Codes UOxxx Generic SAE COxxx Generic SAE U1xxx Manufacturer Specific C1xxx Manufacturer Specific U2xxx Manufacturer Specific C2xxx Manufacturer Specific U3xxx Generic SAE C3xxx Generic SAE EQP 103 User s Manual 3 2 About the Code Reader Code Reader Controls EQP 103 A OBD II Port
20. h IMPORTAN l Do not soak keypad as water might find its way into the code reader Accessories Included No Part Description Provides operation instructions for the 1 User s Manual usage of code reader Provides USB communications for i ee Gabig updates of software and DTCs 3 OBDII Cable Provides connection for vehicle s DLC Provides power to the code reader 4 Cell Battery when disconnected from vehicle EQP 103 User s Manual Specifications 11 Display Indicators Below is a list indictors used to help navigate through menus No Item Specification 1 Display Backlit 160 x 105 pixel display with contrast adjustment g orang 0 to 60 C 32 to 140 F Temperature a Siorage 20 to 70 C 4 to 158 F Temperature 4 a 8 18 Volts powered by vehicle battery ower 5 Internal Power 9V 6 Dimensions 185mm 85mm 35mm L W H 7 28 3 35 1 38in 7 Weight 0 7Kg No Indicator Description 1 Indicates the control module number 5 Indicates more than one screen of information is available 3 Indicates help information available 4 G Indicates graphic viewing of PID is available 5 a Indicates internal battery level EQP 103 User s Manual 12 Power The code reader is powered up by vehicle battery when diagnosing and it is powered up by internal battery when off vehicle reviewing test results an
21. he DTCs P 1 Use lt Select File gt to locate update file downloaded Update DTC 1 Connect device to computer with the USB cable supplied 2 Click lt Select File gt to locate update file 3 Press the UP key of your device 4 Click lt Update gt to start upgrading Cia ED 2 Press the UP key and a Connecting to PC message shows on EQP 103 screen 3 Click lt Update gt to start updating 6 2 Printing The Print Data function is used to print test results through computer To print test results P 1 Download and launch PC Link as instructed on page 53 of 6 1 Updating the Code Reader 2 Start the printing application by selecting the Print tab 3 Connect EQP 103 to computer with the USB cable supplied to power it on 4 Use the UP DOWN key to select Print Data from Main Menu screen EQP 103 User s Manual 55 q Diagnostics Review Data Code Lookup System Setup Tool Information 5 Press the ENTER key to confirm 6 Use the UP DOWN key to select desired data to print Stored Codes Codes a Pending Codes Live Data Freeze Data I M Readiness O2 Monitor Test V If all recorded data to be printed use the UP DOWN key to select Print All 7 Press the ENTER key to load data to your computer 8 Use the BACK key to return to Main Menu 7 Troubleshooting 7 1 Error Message When a Communication Error message displays please check the following EQP 103 User s Manual
22. ilable on all vehicles V Some vehicles need to be driven for a long period of time to store a code after a drivability fault occurs If Trigger On DTCs is selected to make a recording there might not be drastic change in the data before and after trigger ACAUTION Do not operate the code reader while driving always have two persons in vehicle when recording one to drive and the other to operate the code reader EQP 103 User s Manual 35 To record live data 1 Use the UP DOWN key to select Record Data from Datastream screen View Data Record Data 7 Playback Data 2 Press the ENTER key to confirm 3 Refer to View Data to set up Complete Data List or Customer Data List to record 4 Use the UP DOWN key to pick a trigger mode Pick Trigger Method Manual Trigger Trigger On DTC 5 Press the ENTER key to confirm 6 Use the UP DOWN key to pick a memory area EQP 103 User s Manual 36 Select Memory z Area 2 i Area 3 V The asterisk on the screen indicates that a recording currently exist in this memory area vV If an area with an asterisk was picked a message prompting to erase data displays Select Memory Previous recording exists Erase it and make a new one lt YES gt NO vV If Manual Trigger is selected following screen displays Manual Trigger Ready to record ENTER START EQP 103 User s Manual 37 V If Trigger on DTCs is picked following s
23. mponent Test 7 Evap Leak Test i 4 Press the ENTER key to star testing and the code read displays a Command Sent message vV If vehicle being tested does not support this function the code reader displays a Not Support This Function prompt 5 Press the BACK key to return to Diagnostic Menu 5 9 Reading Vehicle Information The Vehicle Information function is used to request the vehicle s VIN number calibration ID s which identifies software version in vehicle control module s calibration verification numbers CVN s and in use performance tracking on model year 2000 and newer OBD II compliant vehicles V CVNs are calculated values required by OBD II regulations They are reported to check if emission related calibrations have been changed Multiple CVNs may be reported for a control module It may take several minutes to do the CVN calculation vV In use performance tracking tracks performance of key readiness monitors To request vehicle information gt 1 Use the UP DOWN key to select Vehicle Information from Diagnostic Menu screen EQP 103 User s Manual 50 Diagnostic Menu On Board Mon Test Component Test R Vehicle Information Modules Present Measurement Unit 2 Press the ENTER key to confirm 3 Observe on screen instruction and wait a few seconds or press any key to continue Vehicle Information Turn key on with engine off Any key to continue V Some vehicle may
24. n of information is retrieved use the UP DOWN key to view additional data V If no freeze frame detected a No Freeze Data Found message displays EQP 103 User s Manual 41 V Some vehicles may not support this function and a Not Support This Function message displays 4 Press the ENTER key to return to Diagnostic Menu 5 5 Reading I M Readiness Status Data The M Readiness function is used to view a snapshot of the operations for the emission system on OBDII EOBD vehicles V I M Readiness is a useful function used to check if all monitors are OK or N A V The vehicle s computer performs tests on the emission system during normal driving conditions After a specific amount of drive time each monitor has specific driving conditions and time required the computer s monitors decide if the vehicle s emission system is working correctly When the monitor s status is e OK vehicle was driven enough to complete the monitor INC Incomplete vehicle was not driven enough to complete the monitor N A Not Applicable vehicle does not support that monitor V I M Readiness function is performed with the KOER or KOEO V There are two types of I M Readiness tests e Since DTCs Cleared shows status of the monitors since the DTCs were last cleared e This Drive Cycle shows status of monitors since the start of the current drive cycle V Below is a list of abbreviations and names of OBD II monitors
25. not support this function and a Not Support This Function message displays 4 Press the ENTER key to confirm 5 Use the UP DOWN key to select an available item from Vehicle Information screen EQP 103 User s Manual 51 Vehicle Information Calibration ID 6 Press the ENTER key to view retrieved information Calibration ID Cal ID 06A906032SD 6462 7 Press the ENTER key return NOTE Not all data is supported by all vehicles 5 10 Modules Present The code reader identifies module IDs and communication protocols for OBD2 modules in the vehicle To view module IDs and communication types gt 1 Use the UP DOWN key to select Modules Present from Diagnostic Menu screen EQP 103 User s Manual 52 Diagnostic Menu 7 On Board Mon Test is Component Test Vehicle Information Modules Present Measurement Unit 2 Press the ENTER key to view information Modules Present Protocol ISO 9141 2 ISO 9141 2 6 Updating and Printing EQP 103 is able to be updated to keep you current with the latest development of diagnosis Also it allows you to upload recorded test results to your PC or laptop for analysis and printing EQP 103 User s Manual 53 6 1 Updating the Code Reader The update of EQP 103 consists of two parts program upgrade and DTC upgrade V To update the code reader you need the following tools EQP 103 EOBD Code Reader e Update Tool PC Link e P
26. om Main Menu screen Diagnostics Review Data Print Data Code Lookup System Setup Tool Information V7 Follow on screen instructions to program the code reader to meet your specific needs Changing Language V The code reader is set to display English menus by default To change system language 1 Use the UP DOWN key to select Language from System Setup screen 2 Press the ENTER key to confirm System Setup 7 Language p Contrast Measurement Unit Auto Power Off Beeper Tool Self Tests EQP 103 User s Manual 14 3 Use the UP DOWN key to select desired language D language Deutsch Dutch English Espanol Francais 4 Press the ENTER key to save language setting and return Adjusting Display Contrast To adjust display contrast 1 Use the UP DOWN key to select Contrast from System Setup screen 2 Press the ENTER key to confirm System Setup PJ Language Contrast Measurement Unit Auto Power Off Beeper Tool Self Tests 3 Use the UP DOWN key to adjust contrast EQP 103 User s Manual 15 Contrast 30 EStt UP DOWN Adjust 4 Press the ENTER key to save contrast setting and return Changing Measurement Unit V Metric is the default measurement unit To change measurement unit P 1 Use the UP DOWN key to select Measurement Unit from System Setup screen 2 Press the ENTER key to confirm System Setup P Language Contrast Measurement Unit A
27. ool Information The 7oo Information function is used to view tool information such as software version that may be needed when contacting customer service To view tool information 1 Use the UP DOWN key to select Tool Information from Main Menu screen EQP 103 User s Manual 21 7 Diagnostics Review Data Print Data Code Lookup System Setup Tool Information 2 Press the ENTER key to view information Tool Information S W Ver V1 00 H W Ver V1 00 LIB Ver V1 0 Code Lookup This function is used to request DTC definitions stored in the code reader To look up DTCs gt 1 Use the UP DOWN key to select Code Lookup from Main Menu screen Main Menu LSS TOE aS 2 Diagnostics Review Data Print Data fof CH Mole lt 0 0 System Setup Tool Information EQP 103 User s Manual 22 2 Use the ENTER key to confirm 3 Use the UP DOWN key to change highlighted character press the ENTER key to confirm and the cursor moves to the next character automatically P0001 UP DOWN CHANGE ENTER CONFIRM BACK EXIT 4 Press the ENTER key to view the DTC definition 5 To view next or previous DTC use the UP DOWN key V If definition could not be found SAE or Manufacturer Specific the code reader displays DTC definition not found Please refer to vehicle service manual V For manufacturer specific codes you need to select a vehicle make on an additional screen to look for DT
28. provides communication for vehicle DLC B LCD Display shows menus test results and operation tips C UP Key moves selection up Scrolls back and forth through codes retrieved Press it from home screen to enter the DTC update mode when doing upgrading D DOWN Key moves selection down Scrolls back and forth through codes retrieved Press it from home screen to do language selection EQP 103 User s Manual 10 E HELP Key accesses to the Help function F BACK Key cancels an action and returns to previous screen or level G Also press it to enter system setup menu from home screen ENTER Key confirms an action or movement and moves to next level Starts recording live data under manual trigger mode Selects or deselects PID when viewing or recording custom PID s Hold the ENTER key for 2 seconds to view or record customized PID list When doing playback of live data use this key to scroll back and forth through frames of data Use the key to view PID graphs when the G icon appears Also press it to go to next screen of information when code definition covers more than 1 screen Power Switch Turns on off the scan tool when powered by cell battery resets the code reader when powered by vehicle battery USB Port provides a USB connection between the code reader and PC or laptop IMPORTAN I Do not use solvents such as alcohol to clean keypad or display Use a mild nonabrasive detergent and a soft cotton clot
29. rive Cycle MIL Status OFF Misfire Monitor N A Fuel System Mon N A Comp Component OK Catalyst Mon N A Htd Catalyst N A EQP 103 User s Manual 44 V If more than one screen of information is retrieved use the UP DOWN key to view additional data V Some vehicles may not support this function and a Not Supported Function message displays 4 Press the BACK key to return to Diagnostic Menu 5 6 O2 Monitor Test OBD II regulations require certain vehicles to monitor and test oxygen O2 sensors to isolate fuel and emissions related faults The O2 Monitor Testfunction is used to retrieve completed test results V The O2 Monitor Test is not an on demand test O2 sensors are not tested when selected via the menu but tested when engine operating conditions are within specified limits V If the vehicle uses a controller area network CAN protocol to communicate this function is not supported by vehicle Refer to On Board Monitor Tests on page 45 for O2 monitor data of CAN equipped vehicles To retrieve O2 monitor data gt 1 Use the UP DOWN key to select O2 Monitor Test from Diagnostic Menu screen Diagnostic Menu 2 Read Codes Clear Codes Datastream Freeze Data I M Readiness O2 Monitor Test 2 Press the ENTER key to confirm 3 Use the UP DOWN key to pick desired O2 sensor EQP 103 User s Manual 45 O2 Monitor Test 7 O2 Bank1 Sensori O2 Bank1 Sensor2 vV If the vehicle being tested
30. rking correctly To check LCD 1 Use the UP DOWN key to select Tool Self Tests from System Setup screen 2 Press the ENTER key to confirm System Setup 2 Language Contrast Measurement Unit Auto Power Off Beeper Tool Self Tests 3 Use the UP DOWN key to select Display Test from T7oo Self Tests screen EQP 103 User s Manual 19 Tool Self Tests 7 Display Test Test E Keyboard Test 4 Use the ENTER key to confirm and start testing 5 When completed use the ENTER key to return To check keypad gt 1 Use the UP DOWN key to select Tool Self Tests from System Setup screen 2 Press the ENTER key to confirm System Setup F Language Contrast Measurement Unit Auto Power Off Beeper Tool Self Tests 3 Use the UP DOWN key to select Keyboard Test from Tool Self Tests screen EQP 103 User s Manual 20 Tool Self Tests Display Test Keyboard Test 4 Press any key to start Key name or scroll direction should show on display when you press a key V The only exception is the POWER key When you press and hold the key its name does not display on the screen but resets the code reader when powered by vehicle battery or turns off the tool when powered by cell battery If it does not reboot or power off the code reader the key is not working properly Keyboard Test Press any key to start test Key 2x BACK Return 5 Double press the BACK key to return T
31. serious injury to the operator or to bystanders Indicates a potentially hazardous situation which if not avoided could AWARNING i Lee 2 ae result in death or serious injury to the operator or to bystanders Indicates a potentially hazardous situation which if not avoided may result a ACAUTION in moderate or minor injury to the operator or to bystanders 1 1 Important Safety Instructions Always use your code reader as described in the user s manual and follow all safety messages Do not route the test cable in a manner that would interfere with driving controls EQP 103 User s Manual AWaARNING Do not exceed voltage limits between inputs specified in this user s manual Always wear ANSI approved goggles to protect your eyes from propelled objects as well as hot or caustic liquids Fuel oil vapors hot steam hot toxic exhaust gases acid refrigerant and other debris produced by a malfunction engine can Cause serious injury or death Do not use code reader in areas where explosive vapor may collect such as in below ground pits confined areas or areas that are less than 18 inches 45 cm above the floor Do not smoke strike a match or cause a spark near the vehicle while testing and keep all sparks heated items and open flames away from the battery and fuel fuel vapors as they are highly flammable AWARNING Keep a dry chemical fire extinguisher suitable for gasoline chemic
32. the ENTER key to playback 5 Use the UP DOWN key to view PIDs of each frame or use the ENTER key to move back and forth through frames Playback 5 22 n FUELSYS1 OL Drive FUELSYST2 N A LOAD_PCT 0 0 ETC F 172 SHRTFT1 0 0 LONGFT1 0 0 V The number to the upper right corner of display indicates the total number of recorded frames and sequence of currently displayed frame V Negative frame indicates data recorded before trigger point and positive frame indicates data recorded after trigger V The G icon indicates graphing is available for the selected PID Use the ENTER key to view graphing and use the UP DOWN key to scroll back and forth through graphs 6 Use the BACK key to return to Playback Data EQP 103 User s Manual 40 5 4 Viewing Freeze Data The Freeze Data function is used to view freeze frame data a snapshot of vehicle operating conditions recorded by the on board computer at the time of an emission related fault V If codes were cleared freeze data may not be stored in vehicle memory depending on vehicle To view freeze frame data P 1 Use the UP DOWN key to select Freeze Data from Diagnostic Menu screen DIETIKE z Read Codes Clear Codes Datastream I M Readiness O2 Monitor Test 2 Press the ENTER key to confirm 3 View freeze frame data on screen DTCFRZF P0130 FUELSYS1 OL Drive FUELSYST2 N A LOAD_PCT 0 0 ETC F SHRTFT1 0 0 V If more than one scree
33. the protocol throughout the testing till another vehicle is diagnosed V If the code reader fails to communicate with the vehicle a Communication Error message displays Make sure the OBDII connector is securely attached and the ignition key is on Turn vehicle key to off for 10 seconds then on If problem still exists refer to Error Messages on page 55 of Troubleshooting V When the code reader links to vehicle it checks the status of I M Monitors and gives a summary report on the display as illustrated below EQP 103 User s Manual 25 System Status MIL Status ON Code Found Monitors N A Monitors OK Monitors INC V If vehicle is equipped with more than one computer module for example a powertrain control module PCM and a transmission control module TCM the code reader identifies them by their identification names ID assigned by manufacturer i e Engine or Module A4 To perform diagnosis gt 1 Press the ENTER key from home screen to view Main Menu 2 Use the UP DOWN key to select Diagnostics from Main Menu screen Diagnostics Review Data Print Data Code Lookup System Setup Tool Information 3 Select YES to erase previous recording and make a new one EQP 103 User s Manual 26 Clear existing recording and save data from this test lt YES gt NO V If previous recording not to be erased select NO V If no data exist in the tool above prompt is not
34. u
35. uto Power Off Beeper Tool Self Tests 3 Use the UP DOWN key to select desired measurement unit EQP 103 User s Manual 16 Measurement Unit 7 Metric 4 Press the ENTER key to save measurement setting and return Changing Auto Power Off V The minimum auto power off time is 1 minute and the maximum is 20 minutes V The Auto Power Off function is available only when the code reader is powered by internal battery To change auto power off time 1 Use the UP DOWN key to select Auto Power Off from System Setup screen 2 Press the ENTER key to confirm System Setup Language Contrast Measurement Unit Auto Power Off Beeper Tool Self Tests 3 Use the UP DOWN key to increase or decrease time EQP 103 User s Manual 17 Auto Power off 01 Minute UP Increase time DOWN Decrease time ENTER Confirm 4 Use the ENTER key to save Turning on off Beeper V The beeper is on by default To turn beeper on off 1 Use the UP DOWN key to select Beeper from System Setup screen 2 Press the ENTER key to confirm System Setup Language Contrast Measurement Unit Auto Power Off Tool Self Tests 3 Use the UP DOWN key to select desired choice EQP 103 User s Manual 18 Beep ON ON Beeper OFF 4 Use the ENTER key to save beeper sound setting Checking LCD and Keypad The 7Joo Self Tesis function is used to check if the LCD display and the operation of keypad are wo

USER'S MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents