User Manual VD-5000(W)
Contents
1. Caution The SD card is the only usable SD card for this product In case of a lost SD card please contact your local retail shop to purchase a replacement If a damaged or a non authentic SD card is used the recorded data maybe damaged or will not record and or replay due to difference in quality Caution Do not disassemble or remodel this product as it can cause an electric shock Any malfunctioning after such action will result in the product being unfit for use and void all warranty service provisions Consult the retailer for product maintenance and repairs if necessary Only use adaptors with the appropriate specifications The use of other adaptors will defect the product and or cause fire All wiring should be carefully implemented so the cable may not be damaged When installing the device to your vehicle follow all the procedures and make sure the mount is secure Unclean surfaces will weaken the adhesive strength and can damage the product if it drops due to weak adhesion This product is not waterproof Do not allow liquids and impurities to enter the product Where the product is wired to the power supply of the vehicle directly or if the cigar jack is connected to the power supply while the engine is off make sure to disconnect the device to prevent battery drain on your vehicle Do not use chemicals or detergents to clean the device This can result in malfunctioning of the product Accumulation of impurit2. 11 Installation Procedure 5 Adjust the camera angle Move the camera top to bottom to fix it to a recordable position while checking the LCD For better images and operation of the analysis program ensure that the horizon meets 1 2 of the screen in the recorded data 12 Installation Procedure Windshield N Vehicle Exterior Vehicle Interior Driver s Side When the unit is attached set the camera to face the front direction of the vehicle Highest Position Position Camera is adjustable and can be rotated 65 degrees to cover desired recording areas 13 Installation Procedure 6 Check LED lamps The GPS lamp is red when the GPS signal is not received and blue when it is received The GPS connection may take a couple of seconds to several minutes depending on the location of your vehicle The REC lamp is blue when it is recording It is blue when it is recording a NORMAL file and red when recording an EVENT file after an impact or if the SHOT button has been pressed 7 Arrange wires Use the enclosed wire holders to organize the cable line 14 Product Use B Startup Turn off the engine and remove the key from ignition Check to see if the SD card is inserted into the unit Turn on the engine When the engine is turned on the system boot starts with the program installed in the SD card and a voice notification will be annou
3. While no impacts the system records 4 frames second to save the SD space and return to normal full frame recording mode making an EVENT file when it receives a certain impact to car After making an EVENT file it returns to 4 frame recording mode again No audio is recorded while parking mode is on n parking mode the system repeats Parking mode is on every 2 minutes To return to normal driving recording mode press and hold the PLAY button for more than 3 seconds to hear the Driving mode on announcement To use the parking mode the product has to be connected to the power source directly In regards to direct wiring to the vehicle s power source we recommend using professional help Extensive and continuous use of the vehicle s power source may exhaust the performance of the product The company is not liable for the damages from continuous use of the product more than 24 hours We recommend the full power to be off after use of 2 3 days to maintain the product for longer use B Voice Recording During the system records when the SHOT button is pressed and held for more than 3 seconds the voice notification will announce that the voice recording will initiate and the voice recording will start or stop he initial audio recording setting can be changed in the analysis program 17 Product Use B 50 Card Use Users are recommended to use the SD card issued from the manufacturer T
4. accidental or on purpose Product has been exposed to extremes in temperature and humidity Warranty repairs are available only in the country where the product is purchased 2 Warranty Certificate Warranty Certificate VISIONDAIVE Warranty If the product malfunctions after the 1 year warranty period expires no service is provided under warranty If the certificate does not have the date of purchase the 1 year warranty is calculated by the serial number s production date plus an additional 1 month to calculate the 1 year warranty period If no serial number then no warranty is available The manufacturer will follow Consumer Protection Act 1006 36 to give warranty to all the products sold to consumers in the available regions All A S services are given by either the manufacturer or the designated service centers under an agreement with the manufacturer A decline of the warranty coverage will be notified to the customer within 14 working days of the application If the application is accepted the coverage will be in full effect within 30 days All H W S W design and logo of the product is copyrighted by the manufac turer of the product Copy disassembly remake and distribution of the product without the manufacturer s written consent is strictly prohibited This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device m
5. G40x480 VGA SOfps Max Deme e Installation Precautions For safe installation and operation carefully read all the information stated below DO NOT disconnect the power supply while the system is booting up Be aware of engine ignition switching for they may disconnect power for short periods of time It is recommended to only use authorized SD cards with the VisionDrive products Install the product after parking your vehicle in a bright and safe area Install the system when ignition is off especially after the power source has been turned off completely Use the power cable provided with the product for the cigarette lighter power connection for power in the range of DC12V to DC24V If power wiring is involved we recommend a professional service for the installation Prior to the installation clean the area of the installation where the camera will be positioned DO NOT eject the SD card while the product is in operation Installation Sequence 1 Connect the bracket and the main unit 2 Insert SD card into the unit 3 Connect cable and attach on windshield 4 Connect to power source and turn on the unit 5 Adjust the camera angle 6 Check LED lamps 7 Arrange wires using wire holders Installation Procedure 1 Connect the bracket and the main unit Connect the attachment bracket with the main unit and push it to the direction 1 to secure the lock to hear th
6. defection of the product Also do not expose the product to direct fire or water Do not disassemble the product Disassembly without caution may result in product defect Keep the SD card in its case when not in use in the product Static electricity or other environmental elements can damage the recorded data SD cards are an expendable supply After normal periods of use partial memory sectors may be damaged and will disable the recording of data The system installed on the SD card provides an automated checking function If use of the automatic checking function identifies problems with the SD card then we recommend purchasing a new SD card for recording data If the SD card is ejected or the system is turned off while recording copying or deleting a data stored data may be lost or damaged In a worst case scenario the SD card may become defective We the company are not responsible for loss or destruction of stored data Copy and keep important data on other data storages such as hard disk CD portable flash memory Components Components are subject to change without prior notice Main Unit Attachment SD card Wire holders Cigar Power Bracket Adaptor Mount Part Names GPS LED REC LED VIEW BUTTON LCD SCREEN PLAY BUTTON SD CARD SLOT SHOT BUTTON GPS SENSOR CAMERA BRACKET ATTACHED TO THE UNIT S BODY POWER PORT STECH SUPPORT PORT Product Specification
7. User Manual ver vD 5000 W 1 0E VISIONDRIVE CAR BLACK BOX Technology and Life INDEX 10 11 Before Use Caution Components Part Names Product Specifications Installation Precautions Installation Sequence Installation Procedure Product Use Analysis Program Use Warranty Before Use Thank you for choosing VisionDrive M The following contents describe the scope of the warranty service covered by us and product cautions B Warranty Service and Responsibility We shall not be held responsible for damage caused by errors or data loss of this product as well as any damages or losses derived from the device not operating normally The product is designed to record store play and analyze videos caused by impacts and car accidents or as recorded by user s discretion However it is not assured that the product will record video in every instance Furthermore under circumstances where the impact is too weak the vibration sensor may not be able to detect the impact which induces that the system will be unable to automatically start recording the Event file In such a situation the urgent save button SHOT on the product should be pressed to start recording a video to the Event folder The information in this manual may change without prior notice due to technical changes or upgrades Check for updates periodically to ensure full knowledge of both the warranty service and responsibility scope
8. ay not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Caution Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense All hardwares softwares design and logo of the product is copyrighted by the manufacturer of the product Copy disassembly remake and distribution without the manufacturer s consent is prohibited and will be enforced by all legal rights held by the manufacturer www visiondrive co kr A gt GeoCross 29 VISIONDRIVE CAR BLACK BOX 49 GeoCross www visiondrive co kr echnology and Life
9. e SD card Shock Sensor Setting Sensitive Insensitive MEE sot a ee E MEE X Front amp Back 1 v Left amp Right f Z Up amp Down The sensor be configured If the number is larger on the sensor the sensor becomes less sensitive 24 PC Analysis Program Use B Configuration Record Setting Record time after event seconds Event file storage size 9 Audio Record Audio Record OM Audio Record OFF I 1 1 1 1 1 1 Sensor Trigger volurne T Low High Sound Option Event Start up Parking Made You can set the recording time after an impact 10 seconds prior to the impact are recorded and stored Impact files are stored in EVENT Folder and the size of the EVENT Folder is set here The rest remaining 96 of the SD card space is for the NORMAL Folder Audio recording is selectable here but regardless of this setting you can immediately change the audio recording status by pushing the SHOT button on the main unit Impact sound volume can be modified Each of Sound Option can make Event Alarm Start up Greeting Parking Mode Notice sounds on off The voice recording and the impact alert setting can be configured Vehicle Information You can type in your car information which will be shown in the video during playback Speed Alarm ON 100 Km h When set to a defined number the system
10. e click sound Move the bracket to direction 2 to release the bracket Insert the SD card as shown in the picture When ejecting the SD card from the unit turn off the main power When ejecting the SD card from the unit turn off the main power completely and then push in the SD card The SD card will pop out when pushed in Use of force or other methods to eject the SD card may defect the SD card 10 Installation Procedure 3 Connect cable and attach on windshield Clean the area on the windshield where the unit will be installed For the placement of the unit it is better to place the unit closer to the center of the vehicle If the unit is installed on the right side of the back mirror make sure there is room to detach the unit if needed Also be aware of window tinting or other window coatings shielding which may affect camera visibility The adhesive on the bracket is very strong Partially remove the cover of the adhesive and then use the full adhesive surface area for final installation 4 Connect to power source and turn on the unit Insert the cigarette jack into an appropriate outlet then turn on the engine When the power is on the LEDs and the LCO will turn on and a voice notification will be announced M Blinking of LED lamps notifies that the system booting has succeeded DO NOT turn off the power source while the system boot is in progress This may damage the product
11. ered eg eg 124537834 20090102 124537834 1 vd NOGPS 12345678 1 vd No GPS 19 PC Analysis Program Use B File searching by preview function When a file chosen is selected from the list the screen shows the first frame of the file for your easier ease of reference A double click on the selected file in the list plays the video on the screen VIS 8 DRIVE Forever Mgr fes FO 00 09 28 11 53 45 E126 956062 N17 T9255 B Auto play Function After you double click a file the following recordings will automatically and continuously play one after another However the EVENT and NORMAL folders are not continuously connected with each other Each folder has to be opened separately 20 PC Analysis Program Use B Positioning on the map With the GPS data the map shows the location of the vehicle while playing the recorded data The Google map is viewable only whilst your is connected to the Internet Harewood HarewoodAve Leeds Golf Wike Moo Gi Centre servoir io Sand Moor M Shock Sensor Graph The graph below shows impacts on the x y z axis of the vehicle X axis measures and records impacts from the front and back of the vehicle 0G 8G is registered Y axis measures and records impacts from the left and right sides of the vehicle 0G 8G is registered Z axis measures and records impacts from the top and lower part of the
12. he SD cards contain programs necessary to operate the product Also the provided SD card is tested and certified by the manufacturer while other SD cards may not match the performance and specifications that authentic VisionDrive SD cards can offer To eject the SD card from the product the engine has to be turned off and the key should be removed from the ignition A few seconds after the key has been removed the product will turn off automatically and the LED lamps will be turned off as well The built in back up battery allows the last images to be stored into proper folders before the product is completely turned off Wait until the LED lamps are turned off then remove the SD card When the SD card is removed it needs to be reinserted before you drive your car again Without the SD card the product will not function properly Use only SDHC supporting SD card readers to read the SD HC card f a voice notification repeatedly announces to insert a correct SD card it means the SO card is defected or damaged Purchase a replacement SD card readers can be purchased at computer accessory stores B Automatic System Check and Safe Rebooting Function This product is programmed to automatically check and reboot the system if the product is in a non functional status By rebooting the system the product can notify to the user while it is processing that such action is being taken place By safeguarding the
13. ies on the camera lens or the window surface near the camera may result in video distortion and reduced clarity of recorded data These areas of the product should always be kept clean Excessive tinting on the window may also distort or reduce clarity of recorded data Note Recording can be distorted under the condition where brightness suddenly changes like passing through a tunnel direct sunlight reflection during day time or where only low light is available at night time If not enough light is available using additional external lighting may help record better images Caution In case of slight impact the product may not be able to create an event file automatically it is however recorded as a Normal file In such a case please use the SHOT button to create an event file manually If you eject the SD card while the product is on the recorded data may be damaged Make sure the main power is completely off and the device is fully powered off no indicator lights are on before removing the SD card from the product Interacting with the product while driving is risky and may cause an accident This should only be performed when the vehicles is stationary and parked in a safe place Dropping or causing an impact on the product during operation can cause defects or fire Do not keep the product in extreme temperatures or in humid areas Being under extreme heat in summer days or freezing cold in winter days may result in
14. nced Then the REC and GPS lamps will turn on The REC lamp will turn blue while blinking The GPS lamp will turn red if no signal and blue if receiving signal The GPS connection may take a couple of seconds to several minutes depending on the location of the vehicle Normal Recording and Event Recording While the power is on the normal recording is on as well The REC lamp will be blinking blue n normal recording mode files will be recorded as 5 minute files and stored in the NORMAL folder If the memory is full while in normal or event recording mode the program will erase the oldest recorded data then record a new file The management is based on First In First Out FIFO n the case of an impact the sensors will trigger the event mode An alarm will sound to notify the user The REC lamp will be red and the recorded data will be saved in EVENT folder When an impact is registered and the event file is stored the program records 10 seconds prior to the impact and 15 60 seconds after the impact adjustable in the configuration Memory size allocation between EVENT folder and NORMAL folder is modifiable in the configuration settings B Manual event Recording When the SHOT button is pressed the alarm will sound and the recorded data will be saved in the EVENT folder Even though impacts cause the system to automatically record event files the SHOT button can also be u
15. sed to record scenes of other accidents or to record great scenery you may want to save while driving 15 Product Use M Viewing 1 Viewing recording videos on LCD 1 Main camera image shows when system boots 2 LCD turns off at the 2nd click on the V button 3 Another click on the V button starts the sequence from 1 2 again Note Operate the system while the car is securely stopped for your safety 2 Playback of the recorded videos on LCO PLAY button starts the latest videos files VIEW button changes the videos according to time sequences Date and time data shows on the bottom of LCD There is no time sign on LCD when no GPS data registered You can enlarge the video on LCD whilst the video is being played by clicking the PLAY button It can enlarge x2 and x4 times and return to original size Original Size x2 Size x4 Size A longer press of PLAY button for more than 3 seconds will make the system return to recording mode followed by an announcement of audio recording status 16 Product Use B Parked Surveillance Mode To enter into the Parking Mode recording push and hold the PLAY button for more than 3 seconds when the system is recording and a voice notification will be announced that the parking mode has been initiated The system automatically rearranges its impact sensing sensitivity to most sensitive in order to register the slightest impacts
16. system in this manner the stability of the system is reinforced If the system keeps rebooting repeatedly the program installed in the SD card may have been damaged or altered Use the format program in the SD card sdfv2003 exe to reformat the SD card You can obtain the entire software package from your local reseller 18 PC Analysis Program Use The skin used for the analysis program may differ by the version B Program Start Up After the SD card is connected to the PC open up VISIONDRIVE z the VDAnalyzer exe file in the SD DAnalyzer for VD 5000W Opening the VDAnalyzer exe program password window will show up Type in the default password 12345678 and you can make your own password in configuration settings M How to play the files play a certain file select a file from the list located on the right hand side and double click on it The most recent data will be listed on the top The EVENT folder will be the default folder to show up when you first open the program The NORMAL folder will have normal recording files and you may view them by clicking open on the analyzer The names of the files are shown as below Real Filename Windows File list in the analyzer GPS number date time type vd date time type vd Registered eg eg 124537834 20090102 120102 1 vd 20090102 120102 1 vd number NOGPS number type vd NOGPS number type vd Regist
17. vehicle 0G 8G is registered The bottom and left displays a progress bar showing the time line of the video Red line is before impact and blue after impact 00 30 7 00 31 21 PC Analysis Program Use B PLAY PAUSE PREVIOUS FRAME LATTER FRAME When the play button is pressed it will replay the video file listed on the screen After selecting a file from the list double click the file from the list to play the file When you press the pause button the viewing video will be paused When the previous frame or the latter frame button is pressed it will move backward or forward between frames within the file BRIGHTNESS CONTROL Brightness bar can give you better video analysis by changing the video brightness while playing on PC M SPEED METER While the file is being played the speed meter will show the vehicle s speed that was collected by the GPS PEED 60 milat 22 PC Analysis Program Use B AVI conversion The data files in the SD card are product files and will only work within the Viewer Analyzer program To view the data on a regular PC without having the Viewer Analyzer program within the SD card the recorded file has to be converted to an AVI file Pause the file where you want the conversion to take place on the previewing file display Press the AVI conversion button on the bottom right side and then a
18. will alert your over speeding you when this Speed is exceeded 25 PC Analysis Program Use X B Configuration Line Zone Daylight Saving Time t D 5 T You can select your location and time zone and the GPS will register your local time with your video Speed Type milejh emh Vehicle Type Car C Truck Bus You can select your local speed type as Km h or mile h in the tap You can select your vehicle type as Car or Truck Bus in the tap Password Case sensitive Please enter alphanumeric characters Please re enter your password Your own password can be modified 26 Warranty The warranty is 1 year from date of purchase If the product malfunctions under normal use within the warranty period you can claim repair of product To apply for warranty register your product serial number with your local reseller Only registered products will be accepted for repair or service If the warranty period expires repairs and services can be provided only if expenses paid by the customer In cases below repairs may require expense payment by the customer f the product has been reassembled or disassembled or has been damaged by the customer Damages due to force majeure such as earthquakes thunderstorms etc Using power cables other than that which were provided by the manufacturer Dropping or damaging the product through any means
19. window will pop up to have the file renamed You may put any name you would like There is no need to put avi on the end When making an AVI conversion you can select your options of Audio GPS Date amp Time Carlnfo to be included to the avi file Press the Start button again and then the data being previewed will be converted from the point you specified When you press the pause button while the conversion is in progress the conversion stops from that point f the necessary codec is not available to convert the data into an AVI format file it may not work on your PC or a notification will pop up saying you may need to download a specific codec to proceed In such cases use the supplied Xvid 1 2 1 0412008 exe on the SD card to install the needed codec then restart the Viewer Analyzer program to proceed again If the codec is already installed on the PC there may be some difficulties if the codec is installed twice So unless there is a notification for installing a codec do not install 23 Analysis Program Use B Configuration Video Setting Video Resolution CO Front Max 30 fps Frank amp R Max 10F h COO Rear Max 30 fps Fron ear Max ps each Video Quality High Normal CO Low he video resolution and quality settings can be modified f the resolution is high the file size also becomes larger and will take more memory on th
Download Pdf Manuals
Related Search