Pro ojecte ed Cap pacitivve Inpput (PCI) User Guide
Contents
1. a InPenMount Control Panel under Multiple Monitors tag check the Multiple Monitor Support box Then click Map Touchscreens to assign touch controllers to displays Fig 38 b When the mapping screen message appears click OK Fig 39 c Touch each screen as it displays Please touch this monitor Press S to skip Follow this sequence and touch each screen to map the touchscreens Fig 40 _ PenMount Control Panel Device Multiple Monitors Tools About Y Multiple Monitor Support Fig 39 Fig 40 NOTES e If you change the resolution of display or screen address you have to redo Map Touchscreens so the system understands where the displays are e If you have multiple monitors but only one touchscreen press S to skip mapping step d An Example for 2 Units of Touch Monitor Please make sure the touch monitor had plugged in and detected Fig 41 42 e In PenMount Control Panel under Multiple Monitors tag click Map Touchscreens then click OK Fig 43 Aa Parl Control Pana Device Multiple Monitors Tools About V Multiple Montor Support i ay ME ow 4 a 1024 by 768 pixel Lona A EE L d A al Eat Fig 41 Fig 42 Fig 43 f Please follow the message show the display to match the controller and touchscreen Please click S to skip if the monitor without use touchscreen Fig 44 g When screen jump to Screen 2 please touch it If screen 2 has no touch function press2. S to skip it Fig 45 Fig 44 Fig 45 5 1 1 3 Tools The buttons on such PenMount Control Panel have the following functions Fig 46 Page 12 of 17 PenMount Control Panel Device Multiple Monitors Tools About Draw Test by drarwing on the touch screen e Draw Tests or demonstrates the PenMount i co Show Hide the icon For switching buttons touchscreen operation Right Button Icon Shen Pa lt e Right Button Icon Enable right button function The icon can show on Desktop or in the notification area e Gesture Enable Enable configure Gesture AP to support PenMount gestures recognition E Gesture Enable Gesture Setting Fig 46 Back to Default a 5 1 1 4 Screen Rotation Monitor The function supports nVidia Intel or ATI rotation automatic detection 5 1 2 PenMount Monitor Menu Icon PenMount Monitor icon PM appears in the notification area of Windows XP system when you turn on PenMount Monitor in PenMount utility lt 4 LS pm Leal a a D 12 09 PM PenMount Monitor has the following functions Fig 47 Control Panel wf Device 0 Right Button E Fig 47 Control Panel Open PenMount Control Panel Beep Setting Beep function for each device Right Button When this function is selected a mouse icon appears in the upper right of screen Click this icon to switch between Right and Left Button functions Exit Exits the PenMount Monitor function 5 2 Configure PenMount PCI RS 232 USB
3. Select Uninstall to remove PenMount Windows Universal Driver Fig 11 amp Fig 12 F PenMount P2 USB Driver 1 0 0 2 Uninstall EA EF PenMount P2 USE Driver 1 0 0 2 Uninstall Uninstall Penk eurt P3 USE Dersa 1 0002 50 Cerrar YI ron yA Parea Penaud Ai UGH Gereer 10 0 2 from your Computer Welcome lo the PenMount Pe USB Diver V1 O00 2 Uninstall wizard Periana Pit LU Driver YL 010 22 ral Es uninstalled from tha Polos Poker Okek lUrinstad Thr sired rl guide you through the uniretalacion of bo start the uwaa Peritar F2 LEA Greve 1 0 0 7 starting the unirshellstion male pure Penbicunt PE a T Dotore LSR Gator 1 0035 a Linares Irorre C Program Ai Pordicurd PS UGE Deters Choe head bo continues Fig 10 Fig 11 Fig 12 2 1 3 Install Uninstall PCI PenMount Windows Driver in Win7 To install uninstall PenMount PCI RS 232 and USB driver in Windows Vista 7 is similar to in Windows XP However the default installation mode for PenMount PCI USB driver on Windows XP and Win7 will be mouse device For PenMount PCI RS232 driver the driver will be installed as digitizer device in Win7 If you need to install PenMount USB device as digitizer device in Win7 its not necessary to use PenMount driver After connect the device to computer Win7 system will install inbox driver automatically The default inbox driver of Win7 will set PenMount device as digitizer After install PenMount PCI RS232 driver in Windows 7 environment suc
4. cece cece eccecceceeeeeesueseeeeeeeeeeeeeaeeaeeeeeeeeaeeeeeaesaeeuenenees 5 Chapters PenMount PCIMS Cl ota E a T ido A ated 5 3 1 The first execution of PCIMSOTHaieiiira lick aleic ec anisat sica 5 3 2 POIS SUSO terracota eee ee ete een ee eer 6 3 2 1 SCA 6 3 2 2 O A A O A chats Matatcenoan 6 3 2 3 Panel size selecto acia T 3 2 4 COMMO enna dada 7 3 2 5 Dd qo co eee O 7 Chapter 4 Firmware Field Update Guide ccooocccccocncccccnccccnoconcnocononononnnonnnnnonnnnononnnonnnnnonannnnnnnnononcnononnnenanenes 8 4 1 PenMount Pmfu V1 21 Guide for WINdOWS occoccoccnccnccnccnccnccnncnnnoncnnnoncnnconcnncnnnonnoncnnnnnnnos 8 4 1 1 Firmware Field Update insStructions cccccscccsscecsececeeeeceeeeceeeceececeeeceueesseessueesseeessneess 8 4 2 PenMount Pmfu V1 00 Guide for LINUX tekken eee i 9 4 2 1 Firmware Field Update Step by Step ooccccocccccccnnccccnccononococononocnnonnnnnnonnnononnnononnnonnnnnnonnnss 9 Chapter 5 Configure TOUCASCISON cipal il e A aa eed eet ees 10 5 1 Configure PenMount PCI RS 232 USB In Windows XP oocoooccccccocccccococcocononcnnconanononnonons 10 5 1 1 PERVIOUNIEG A e caia dica 10 Sale DOVIC O osai eesti do ane ieee he en eaeenieds 10 OFZ WITT DICMVIOMINONS pt Ai auto lesen as 11 6 11 98 TOO A A 12 5 1 1 4 Screen Rotation Monitor ooccoccnccnccnccnccnccnconcnnnonconcnnnoncnncnnrnnnnnnnnnnnnnnrnnrnncnnnnnnnnns 13 5 1 2 PenMount Montor Menu ICON iia dad id 13 5 2 Configure PenMount
5. please increase the value If the sensing point shifts too much in the edge area please decrease this value Fig 36 About This tab displays information about the PenMount controller and driver version Fig 37 E Device 0 PenMount PCI USB Setting Edge Compensation About Device 0 PenMount PCI USB Setting Edge Compensation About L PenMount PCI USB 10 bit A Driver Version CEES ee Firmware Version PCI 2 0 32 Fig 36 Fig 37 5 1 1 2 Multiple Monitors Multiple Monitors supports two to four touchscreen displays for one system Each monitor requires its own PenMount PCI board either installed inside the display or in a central unit The PenMount PCI boards must be connected to the computer RS 232 or USB ports Driver installation procedures are the same as for a single monitor Before using Multiple Monitors you must have two or more monitors that are in extension mode For display cards that support multiple monitors we suggest you consider Matrox nVidia or ATI cards and inquire about operation and usability issues NOTE a The Multiple Monitors function is for the use with multiple displays only Do not use this function if you have only one touchscreen display Please note once you turn on this function the Rotating function is disabled b Before you can use multiple monitors you need to map each monitor Page 11 of 17 Enable the multiple display function as follows
6. ATOU OT a a ma o EES See ee eee aor ene 1 1 1 ADOUCNIS Wa Sacer te a Spa do bee oad ea e Latah ak Oe ee 1 1 2 Projected Capacitive Touch Panel cccccsssccccssseecceeceeceeseeecseaseeessaeeeeseageeessaseesssaeeeenes 1 1 3 PenWMount PCl Control BOGAN i 1 1 4 Drivers amp UE ec wlcdiobenlic grcwwlctccdie ieee dom uoledducceice peemaladaseentcanaunealdemennietaneveutacs 1 1 5 Before you start to use this Manual cooooncncococcnncccnccnconanonnnnncononnnnnnnonanonnononcnnnnnnnnnnnnannnos 2 1 6 PES ales Seca 2 Chapter 2 Install Drivers for PenMount PCI BoOardS occccoccncccccncccccccoconononnnonannnonnnnononononnnnnnnnnnnnonnnnnonenenonnnss 2 2 1 PenMount PCI Windows Driver occocccccnccnccnccnncnncnncnnccncnncnncnnnnnnnncnnronnnnnoncnnnnnnnnnrnncnnrnnnnnnns 2 2 1 1 Install PenMount PCI Windows Driver in XP o o coccccccnccncnccnccnccnncnncnncnnnonnnncnnconcnnnnnrnnannnnns 2 2 1 2 Uninstall PenMount PCI Windows Driver in XP oooccoccocccnccnccnconccncnncnncnncnncnncnncnnroncnnnnnnnns 4 2 1 3 Install Uninstall PCI PenMount Windows Driver in WIN7 occoccccccccnccncnncnnncncnnnannn nana 4 2 2 Install PenMount PCI Linux X Window Driver occcccccccnccnccnccnccnccncnncnncnncnnconcnncnnnoncnnnnnnss 4 2 2 1 Install PenMount PCI Linux X Window DriVeF oococccccccccnccnccnccnccnconcnnnonconcnnnoncnnroncnnnnnnos 4 2 3 Install PenMount PCI WinCE DIV eek i ee a he 5 2 3 1 Install PenMount WinCE Drivel
7. In Windows Vista 7 Double click on the PenMount Control Panel icon on the Desktop to open the configuration L utility Fig 48 On the PenMount Control Panel you will be able to see the icon of PenMount PCI RS 232 or USB under Device tab In Device tab you can see the devices PenMount detected on your system Select a device and press the Configure button to configure it cipal 5 2 1 PenMount Control Panel The functions under PenMount Control Panel are Device Tools About Select a device to configure 5 2 1 1 Device In this tab you can find out how many devices are detected on your system Select any device by clicking on its icon Fig 49 Configure Refresh Fig 49 Edge Compensation This page is the edge compensation settings for the advanced calibration You can adjust the settings from 0 to 30 for accommodating the difference of each touch panel Fig 50 Page 13 of 17 About This panel displays information about the PenMount controller and driver version Fig 51 Edge Compensation About The function of Edge Compensation is going to optimize the cursor accuracy on the edge Itis only supported by Advanced Calibration not for Standard Calibration JL PenMount PCI RS232 10 bit COM1 38400bps a Driver Version 2 3 6 Firmware Version PCI 257 1 0 Fig 50 Fig 51 5 2 1 2 Tools Draw Tests or demonstrates the PenMount touchscreen operation Fig 52 Device Tools
8. PCI RS 232 USB In Windows Vista 7 coocccccocnncccccnccocnncnnoo 13 5 2 1 PenMount Control Panel aid 13 5 2 1 1 rn 13 5 2 1 2 A A A tia othe Ad eat 14 5 2 2 MU PE MONOS a e E 14 Chapter 6 Configure PenMount Gesture AP oocooonccccoccnnccnnccnnononcnnononnnnnonnrnnonnncnnonnnnnnnonnnrnnonnnnnnnonnrnnnnnnnrnnnnnns 15 6 1 PenMount Gesture AP for Windows 2000 XP VISTA ccce 15 6 1 1 Invoke PenMount Gesture AP A A xccaen a AAA 15 6 1 2 Configure PenMount Gesture AP onoccoconccccccoconcccncnoconannnnconoconconannnononcnnnnnnnnnnnnannnnenonznnnss 15 Chapter 1 Introduction PenMount Projected Capacitive Touch PCI Control Board is the board for supporting projected capacitive touch There are a series of PCI controller products from PenMount It facilitates the high precision touch activation and dual fingers gesture recognition with minimum touch force required PenMount PCI control board built with all the functionality to operate the PCI touch smoothly Customer could define their product functions and mechanical requirements by referring this manual 1 1 About this Manual This manual describes the features of the PenMount PCI Control Board series how to operate the utility install and use the software drivers and utilities with your operating system This manual is for users who are using the PenMount PCI Control Board and software as well as for engineers who are integrating and customizing the control board for use wi
9. gt PenMount Projected Capacitive Input PCI User Guide Version 1 1 Released date 2012 09 11 Preface Disclaimer The information in this document is subject to change without notice The manufacturer makes no representations or warranties regarding the contents of this manual and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose Furthermore the manufacturer reserves the right to revise this publication or make changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision Trademarks AMT PenMount Microsoft Windows and other trademarks and product names used in this manual are the properties of their respective owners and are acknowledged Copyright This publication including all photographs illustrations and software is protected under international copyright laws with all rights reserved Neither this manual nor any of the material contained herein may be reproduced without the express written consent of the manufacturer Copyright 2012 O Apex Material Technology Corp All rights reserved Revision Table 2012 09 11 Remove the word P2 in user guide Table of Contents A A A A AE EN DISCS IM a a is a e a i MP II a a tte tate catia i o A a al waa etal i ai cans REVISION TAMIL riales Table ONCE NS saddened E haa a E E ds wad cedar asm tts taa ditia iI Enable
10. use edge compensation function in driver to adjust Page 6 of 17 3 2 3 Panel size selection a 3 2 4 Common a Host Connection Please take notice before changing the Host Connection settings in PCIMSet After choosing different interface please connect the PenMount control board with the corresponding cables For example if you use USB for setting PCIMSet and then change Host Connection to RS 232 you will have to use RS232 cable afterwards Panel Sensitivity Parameters Panel Size Common For choosing the suitable sizes of the touch panels Fig 22 Panel P3013 15 0 inch v Panel P3013 15 0 inch 7 Cover Lens v P3013 15 0 inch P3009 12 1 inch Cover Lens For choosing one of the supported cover lens thickness Fig 22 PenMount Cover Lens Fig 22 gy PenMount PCIMSet Sensitivity Parameters Panel Size Common Firmware Version 1400A 1 1 0 RU 15 0 Firmware version The firmware version of PenMount PCI controllers are showed on the AP Version 1 33 Common page Fig 23 AP Version The version of PCIMSet is showed on the Common page Fig 23 oise Level N PenMount Noise Level Reconnect E E me E The values are for calculating the standard deviation of the current environment Fig 23 Fig 23 7 E Standard Deviation Test Test Count 10 100 100 If the operation is not smooth with broken lines or cursor
11. 00ASxxx pmf is the firmware for the slave controller On the other hand PM1100 PM1200 and PM1300 only need to update the master controller firmware johnOlocalhost home john Downloads PCI Firmware johnOlocalhost home john Downloads PCI Firmware File Edit View S sf ak t Hel File Edit View Search Terminal Help aoe PAS jeie SH john localhost su File PM1400A V11 pmf Password Target M14004 rootGlocalhost john cd Downloads PCI Firmware Version 1 1 root localhost PCI Firmware ls SSeS Sa eae PM1100 V13 pmf PM1201A V14 pmf PMI40GAS Vll pmf pmtu i PM1200_V14 pmf PM13G A_V16 pmf PM1400A_V11 pmf ln a root Tocalhost PCI Firmwarel pnfu tne Lainie lt a OS a A Location USB 005 0068 PenMount Firmware Update Utility Firmware Please choose a firmware file listed below pmfwtool Waiting device to settle 0 PM1300A V16 pmf 1 PM1100 V13 pmf Updating Firmware 2 PM1400AS V11 pmf 3 PM1200 V14 pmf 4 PM1400A V11 pmf O NOT disconnect device until update finist 5 PM12014_V14 pmf File Index gt 4 Fig 30 Fig 31 Please do not disconnect device while updating firmware When updating progress reaches 100 the update finishes g If the firmware chosen doesn t match the attached PCI board or the PCI board is not connected an error message will be shown as in Fig 32 m D Please choose a firmware file listed below 0 PM1300 V16 pmf 1 PM1166 V13 pmf
12. 2 PM14064S V11 pmf 3 PM1206 V14 pmf 4 PM14004 V11 pmf 5 PM12014 V14 pmf File Index gt File PM1300A V16 pmf Target PMI3004 Version 1 6 h Fig 32 Page 9 of 17 Chapter 5 Configure Touchscreen This section describes how to configure the PenMount device after installed to windows environment PenMount s driver provides various functions to test and enhance the controller performance under windows environment 5 1 Configure PenMount PCI RS 232 USB In Windows XP Right click on the PenMount monitor icon W in the notification area and select Control Panel from the menu to configure the touchscreen Fig 33 PenMount Control Panel opens You will be able to see the icon of PenMount PCI USB under Device tab In Device tab you can see the devices detected on your system Select a device and press the Configure button to set the configuration Fig 34 PenMount Control Panel Device multiple Monitors Tools About Control Panel Beep Right Button v Gesture Enable Fig 33 Fig 34 5 1 1 PenMount Control Panel The functions under PenMount Control Panel are 5 1 1 1 Device In this tab you can find out how many devices are detected on your system Select any device by clicking on its icon Fig 35 Setting E Device 0 PenMount PCI USB Setting Edge Compensation About Operation Mode Pen Input Emulation v Beep Sound Beep Mode V Cursor Stabilizer sarin q Cursor WG
13. About Test by drarwing on Draw the touch screen Fig 52 5 2 2 Multiple Monitors In Windows Vista 7 environment if you installed PenMount controller as digitizer device you will need to use Multiple Monitors control functions provided by Microsoft to set the touch panel and monitor pairs Here are the operating steps Open Control Panel Find Tablet PC Settings and click Hit Setup Button Fig 53 Touch each screen as it displays If this is not the Tablet PC screen Press Enter to move to the next screen To close the tool press Esc Follow the sequence and touch each screen to map the touchscreens Fig 54 a Tablet PC Settings Diir ee Conlin Caca RP A Touch SS Saclay Pira tia piesa Touch this screen to identity it as the touchscreen E Genara lign Pr Mond ca Tourn input dre TA sena The Tables PL somen press Enter lo maoe to the ned screen To close the tool press Esc Choose the orders wherh pra MTEC rotates aig Criss Fig 54 Page 14 of 17 Chapter 6 Configure PenMount Gesture AP 6 1 PenMount Gesture AP for Windows 2000 XP VISTA 7 This chapter will guide you to the PenMount Gesture AP that is applicable in Windows 2000 XP Vista 7 6 1 1 Invoke PenMount Gesture AP Before install PenMount WindowsXP Vista 7 32bit Driver if you need to use Gesture function please added the parameter Gesture 1 in the install ini file as bellow Fig 55 P Setup Notepad PenMount P2 RS 232 Dr
14. CI drivers support for most common operating system of Windows and Linux systems Please visit our website http www amtouch com tw or http www penmount com tw to see the support O S 2 1 PenMount PCI Windows Driver PenMount provides 2 different drivers for different interface in Windows 2000 XP 2003 7 PenMount RS 232 WindowsXP Vista 7 32bit Driver PenMount USB WindowsXP Vista 7 32bit Driver Under Windows Vista 7 environments PenMount board USB interface could drive with inbox driver 2 1 1 Install PenMount PCI Windows Driver in XP Before install the driver please connect PCI control board to RS232 or USB port of computer Then extract PenMount RS 232 WindowsXP Vista 7 32bit Driver VX X X X zip or PenMount USB WindowsXP Vista 7 32bit Driver VX X X X zip to your disk depends on which interface you connected The installation and operation for PenMount PCI RS 232 and USB driver are almost the same Please refer to the following installation steps Page 2 of 17 Before run the setup exe if you need to use Gesture function please added the parameter Gesture 1 in the install ini file as Fig 1 Then find Setup exe and execute it Fig 2 When Setup Wizard appears click on Next button to proceed Fig 3 E Ponkiount PF R5 337 Driver V1 0 0 1 Setup Welcome lo the PenMount Fe RS 232 Driver V1 0 0 1 Setup a A A AAA AAA Wizard Setup eter nal in Slay e a a a i ep Penhart PS AS 232 Drea V0 0 P Setup Note
15. Fig 61 a Enable disable Check Box Select deselect the box CS Gesture Setting a a to enable disable PenMount Gestures V Enable a General setting D b General Setting Box Sensing Time b 1 Sensing Time Move the slider to adjust PenMount Gestures Sensing Time between 200 ms 0 2 sec and 2500 2 5 sec The shorter the sensing time is configured the faster the gesture has to be done Sensitivity Gesture Setting C d E de i F SHIFT b 2 Sensitivity Move the slider to adjust how sensitive P IR ag Pageup x you want your finger stroke on the touchscreen to be Please click the d 2 above button to choose WINDOW sensed other gesture d 3 C sootcaton Pra c Gesture Settings Group Box This group box 0 4 catin Fs gt allows you to individually configure each gesture d Gesture Select Button Press this button to select a ren the specific gesture you are going to configure When Fig 61 the gesture icon turns to blue it is enabled When it is l gray it is disabled See the following for details d 1 Disable Button When this button is selected the gesture is disabled d 2 Hot key Configure Button Configure the hot keystrokes for specific gesture The hot key can include up to 5 keystrokes When that gesture is sensed the configured keystrokes will be reported d 3 Application Invoke Button Configure to invoke a specific application with particular gesture After the gesture is sensed the speci
16. Monitors Properties Uj Multifunction adapters amp Network adapters Ie 17 Ports COM amp LPT a PenMount PCI Serial a Processors Select your PCP Com port Scan for hardware changes PenMount Reconnect Fig 14 Fig 15 Fig 16 Please make sure that PenMount PCI device has been connected to the PC correctly and then press the Reconnect button lf you have connected USB or RS232 correctly with PC but the setting page still can t appear please make sure that device power has been provided This issue could also be caused by the controller is using different connecting interfaces Note Please do not connect more than one PenMount PCI controller to the computer when using PCIMSet since it can change settings for one PenMount PCI control board only Page 5 of 17 3 2 PCIMSet settings Note Please use mouse for adjusting the settings since touch function will be disabled when PCIMSet is launched PCIMSet settings are as following e Sensitivity e Parameters e Panel Size e Common Each function is described as following 3 2 1 Sensitivity Sensitivity 1 15 Select from 1 to 15 for adjusting the sensitivities The higher value you set the more times that the capacitance will be calculated and the overall capacitance sensing parameters will be increased as well thus the higher sensitivity can be detected and the sample rate will be relatively lower Fig 17 Note After the setting is changed
17. Version 1 21 a Fig 27 Fig 28 When Update finished the result will show Field Update Success Fig 29 E PenMount Field Update FW 14004 11 MENA Resut Field Update Success Interface USB RS232 ing Reload previous parameter PResult Field Update Success Y PMP File Version 14004 1 1 Reconnect and Program Load PMF Exit AP Version 1 21 Fig 29 Page 8 of 17 4 2 PenMount Pmfu V1 00 Guide for Linux The PenMount field update utility omfu is for user to load the updated firmware on field a Please remove any PenMount driver on the target system before running the firmware update utility and reinstall it after the update process finishes b Make sure which interface is used for the PenMount device and then connect PenMount PCI control board to your PC with a USB or RS232 cable 4 2 1 Firmware Field Update Step by Step a Open the terminal b Change the working directory to where the pmfu utility is extracted to the firmware which you want to update need put in the same directory as pmfu c Run pmfu with root permission You will see the firmware list on the screen like as Fig 30 d Choose the firmware by enter the file index For example with PM1400A control board messages will show as in Fig 31 The PM1400A control board has two firmware files and has to be updated twice The first time is for the master controller and the second time is for the slave controller For instance PM14
18. ardware Wizard A RS 232 Driver V1 0 0 1 Setup aaa Wizard Ports COM LPT windows wall seach dor cument and updated poiha by yola ponpa on Hee hodas rotalsicn CO sa the APAA Unelate weh sie vaih yaa permian Penhi 622 232 Dresser VLOO L hes been bretaled on Our computer has not passed Windows Logo testing to verify its compatibility Pinte mu otroc coket with Windows XP Tell me why this testing is important OE Firka ho elos Ei tiara er A s S Can W ndosa oommect bo wing Update lo peanch hor Continuing your installation of this software may impair swye or destabilize the corect operation of your system 20 either immediately or in the future Microsoft strongly Yes this times cd recommends that you stop this installation now and 2 Viet nue are every rre Gone a deve contact the hardware vendor for software that has 7 Mo wee las pros passed Windows Logo testing Click Mest bo continue Continue Anyway STOP Installation a eZ Fig 7 Fig 8 Fig 9 As soon as driver installation finishes you will see the icon of PenMount Monitor W show up in the notification area 2 y 12 09 PM Page 3 of 17 2 1 2 Uninstall PenMount PCI Windows Driver in XP a Exit PenMount Monitor PM in the notification area b Goto Control Panel Click Add Remove program Select PenMount USB Driver V X X X X or PenMount RS 232 Driver V X X X X Click Change Remove button Fig 10 c
19. cessfully You will see the difference that a PenMount Control Panel icon shows up on the desktop without a icon in the notification area And the Gesture AP ES will still show in notification area See the screenshot below Fig 13 Og Computer Control Panel ee D L C PenMount ontrol Panel ME r Fig 13 2 2 Install PenMount PCI Linux X Window Driver Before installing PenMount PCI Linux X Window Driver for PenMount boards you must have Linux X Window installed and running on your computer You must also have PenMount Serial Interface either 110x 120x 1300 1300x 140x control boards installed PenMount PCI Linux X Window Driver for PCI boards support various operating systems The supported Linux version listed on our website Please visit http www amtouch com tw or http www penmount com tw to view the supported Linux versions 2 2 1 Install PenMount PCI Linux X Window Driver Please refer to the readme file included in the driver folder Page 4 of 17 2 3 Install PenMount PCI WinCE Driver Before installing PenMount WinCE Driver you must have WinCE system installed and running on your device You must also have PenMount Serial Interface either 110x 120x 1300 1300x 140x control boards installed NOTE Make sure you can move the WinCE cursor with a serial mouse attached to the target COM port e g COM2 before connecting the PCI control board by RS 232 port 2 3 1 Install PenMount WinCE Driver Please see
20. drifting please om execute Noise Level and do not touch the touch panel before the Result operation finishes A PCIM STDEV Result log file will be generated in aca ae the same directory as PCIMSet Please send this file to PenMount team Fig 24 Fig 24 3 2 5 Others a Reconnect It is for re detecting PenMount PCI device Exit It is for exiting the PCIMSet utility Apply After changing the parameters execute Apply for making them effective Note PCIMset is designed for integrator and designer adjustment purpose If you are end user please don t adjust touch function through utility in driver Page 7 of 17 Chapter 4 Firmware Field Update Guide 4 1 PenMount Pmfu V1 21 Guide for Windows The PenMount field update utility omfu is for user to load the updated firmware on field a C Please remove any PenMount driver on the target system before running the firmware update utility and reinstall it after the update process finishes Make sure which interface is used for the PenMount device and then connect PenMount PCI control board to your PC with a USB or RS232 cable Please use mouse to execute Pmfu 4 1 1 Firmware Field Update instructions a Run the field update program PmFu exe if you don t want to reload previous parameter please uncheck this option then update firmware will use default setting Fig 25 Click on the Load PMF button to find pmf file which the
21. fic application will run d 4 Action Configure Button Configure to make use of PenMount Gesture ERINA AP s built in shortcuts So that when a particular gesture is sensed a EALE Aei Ey z l l Send Right Mouse Click specific action will be taken PenMount Gesture AP have the following Send Middle Mouse Click shortcuts built in Fig 62 Mouse Scroll Forward Note For Disable touch function after touch function is disabled the Mouse Scroll Backward mouse pointer won t move following your finger sliding on the Disable touch function touchscreen and your finger tapping won t trigger any action however Enable touch function gestures will still be sensed Fig 62 Note If you select Disable touch function the curser will not react to finger movement on the touch screen and the tapping will not trigger any program action However the gesture recognition is still functioning Page 17 of 17
22. firmware matches the PCI control board For example with PM1400A control board messages will show as in Fig 26 The PM1400A control board has two firmware files and has to be updated twice The first time is for the master controller and the second time is for the slave controller For instance PM1400ASxxx pmf is the firmware for the slave controller On the other hand PM1100 PM1200 and PM1300 only need to update the master controller firmware Look in PCI Firmware e ce Ee E pm1100_ 13 pmF E pra1200_14 pmf My Recent i pm12014_ 14 pmF Documents f pm1300_ 15 pmf gt E pr13004_Y16 pmf Ey PenMount Field Update al EJer14008_v11 pm ES PM140045_ 11 pmF FW 0000 0 0 Interface e USB C R5232 RS232 Setting Result PMF File Version 0000 j Fie pame PM14004_V11 Reconnect and Program Load PMF Exit AP Version 1 21 js Files of type PMF File v Cancel Aces T Open as read only Fig 25 Fig 26 Click on Reconnect and Program button Fig 27 The firmware will be updated automatically show as in Fig 28 PenMount Field Update on PenMount Field Update FW 0000 0 0 FW 14004 1 1 lt gt Interface Interface USB RS232 e E RS232 Setting i Result Load PMF File Success PMP File Version 14004 1 1 Result Now Programing Please Wait PMP File Version 14004 1 1 AE Reconnect and Program l Load PMF Exit AP Version 1 21 Reconnect and program AP
23. hen using PCIMset This utility is designed for integrator and hardware designer We don t recommend end user to adjust parameters with PCIMset For end customer we suggest the adjustment is better to be done through utility built in PenMount driver After installing the PenMount PCI driver users can use the other PenMount touch functions like edge compensation line test with the utility built in the driver Please refer to AMT or PenMount web for the drivers for PenMount PCI Control Board series support Page 1 of 17 1 5 Before you start to use this manual Check the PCI touch panel and PenMount control board has been integrated properly into the computer system lf your need to integrate the control board and touch panel please refer to AMT Projected Capacitive Touch Panel Integration Guide 1 6 After Sales Service PenMount PCI control board series and software will be updated on a regular basis For more latest updated information downloads and technical support please refer to our website at http www amtouch com tw or http www penmount com tw Chapter 2 Install Drivers for PenMount PCI Boards This chapter describes how to install drivers and other software that enables your PenMount PCI P2 control boards to work with various operating systems PenMount PCI boards support the following connection interfaces di RS 232 PM1100 E ee ee PM1200 O ee a PM1201 ne o PM1300 PM1300A4_ e PM1400 e e PenMount P
24. iver 1 Majorversion Minorversion Bui ldversion Packageversion ScanAllPorts ScanmModel I ScanBaudrate 38400 COML PCI 38400 Fig 55 After install the PenMount WindowsXP Vista 7 32bit Drivers There are two different way to enable the Gesture function a Enable from notification area Select the Gesture Enable item of the right click menu on the PenMount icon in notification area A PenMount Gesture AP icon will show up in the notification area If the icon shows with forbidden red circle that means the gesture function is disable Fig 56 b Enable from PenMount Control Panel In PenMount Control Panel select Tools tab and press Gesture Enable button PenMount Gesture AP icon shows up in the notification area PenMount Gesture AP is running Fig 57 PenMount Control Panel Device Multiple Monitors Tools About Draw Test by drarwing on the touch screen co Show Hide the icon for switching buttons hi2 Right Button Icon Desktop System Tray Control Panel PenMount Gesture AP E Gesture Enable gt Gesture Setting _ S Beep Right Button Gezture Enable Back to Default i Fig 56 FIL The Gesture icon on notification will show 2 different statuses E Enable E Disable If the gesture function can t operate please check if the gesture icon is in Enable status 6 1 2 Configure PenMount Gesture AP To configure PenMount Gesture AP you could call setting function from n
25. kieroo Fig 35 e Operation Mode This mode enables and disables the mouse s ability to drag on screen icons useful for configuring POS terminals Pen Input Emulation Select this mode and mouse will emulate Windows Vista pen input device operation by which no mouse event will be sent until the touch is dragged out of range or released from the screen Click on Touch Select this mode and mouse only provides a click function and dragging is disabled Page 10 of 17 Mouse Emulation Select this mode and mouse functions as normal and allows dragging of icons Click on Release Select this mode and mouse only provides a click function when the touch is released e Beep Sound Beep Sound checkbox Enables disables beep function Beep on pen down Beep occurs when pen comes down Beep on pen up Beep occurs when pen is lifted up Beep on both Beep occurs when comes down and is lifted up Beep Frequency Modifies sound frequency Beep Duration Modifies sound duration Kind of Sound Selects beep sound type e Cursor Stabilizer checkbox Enables disables the function support to prevent cursor shake e Use press and hold as right click You can set the time out and area to your needs Edge Compensation This page is the edge compensation settings for the advanced calibration You can adjust the settings from 0 to 30 for accommodating the difference of each touch panel If the edge area is difficult to touch
26. nt Estar wl ral Penbteurk P2 REDES Drio VILL lev the Polering Folder To instal in a this testing is important diferent Folder click Brower and select fodder Click kial bo start tha ire labio Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the software vendor for software that has passed Windows Logo testing PLEASE READ THE LICENSE AGREEMENT Penkicunt touch screen dover solbe re if only for emp wth Perdidos touch screen controller or control board Any persen or company wang a Penddount diver on any piece ot equpment which does net whlize an Penbiount touch screen controller vall be pronecited te the fall extent of the lam ai Y you accept bhs berms of the ayeme cki Agree be condi Tou mint oom tha apo lo read Pen ark PE SE Driver W1 0 0 0 Continue Anyway Bf C Fig 6 When other Hardware Installation dialogue box appears saying like Fig 7 Click Continue Anyway button to proceed When seeing Found New Hardware Wizard dialogue box appears saying like Fig 8 Click Cancel button to proceed A window notifying of installation completion appears Click Finish button to quit Fig 9 Hardware Installation Found New Hardwar Wizard fn Welcome to the Found New Completing the PenMount P2 The software you are installing for this hardware a H
27. otification area or from PenMount Control Panel Page 15 of 17 a From notification area Right click on the PenMount Gesture AP icon in the notification area select Gesture Setting from the menu that appears See the illustration below Fig 58 b From Control Panel Select Tools tab and press Gesture Setting button in PenMount Control Panel Fig 59 Gesture Setting Window will show Fig 60 CS Gesture Setting Y Enable General Setting Sensing Time PenMount Control Panel Device Multiple Monitors Tools About Sensitivity Draw Test by drarwing on the touch screen Gesture Setting co Show Hide the icon for switching buttons A Right Button Icon Desktop System Tray E SHIFT Q K Page 7 Up Hot Key I ALT PageUp Please chick the CI Gesture Enable Gesture Settin PD GestweEnable z eons F WINDOW C Application SOS Cata a y OK Cancel Back to Default i j oe ren Fig 59 Fig 60 In different operating system there might be different available gestures Backward Forward Left Arrow Right Arrow Copy D Paste Ctrl C B Ctrl V Undo Ctrl Z Zoom in Zoom out Rotate Counter Clockwise Rotate Clockwise Ctrl L Ctrl K Open On Screen Keyboard Save Document Execute OSK EXE Ctrl S Close Program Alt F4 Left Arrow Right Arrow Page 16 of 17 In the Gesture Setting window you can proceed to configure PenMount Gesture AP See picture below
28. pad File Edit Format View Help Th bat remeron echoed hal yet cvs ad ib qual Majorversi on before Sana Baup this rol mabe R pose da Lo ulate Minorversion 0 relevant system Ales without having te reboot your Bui ldversion commuter Packageversion 1 iek 3hn DesktopiPenMount P2 R5 232 WindowsXP Vista 7 32bit Driver 1 0 0 1 v Chei Mart be montira pS SS SSS ORA SS SSS SSS SSS SSS SAM SA SSS SSS SSS RG Am Oat omai oag OO Ank Sak Sad oai oad ond oni at omi ai Dd Driver O Utility ari 7 Setup Setup Configuration Settings 7 1 KB Ei ET Fig 1 Fig 2 Fig 3 A License Agreement window appears Click Agree button to continue installation Fig 4 Choose desirable installation folder path then hit Install Fig 5 The installation proceeds that will appears several Software Installation dialogue box and Hardware Installation dialogue box For example When seeing Software Installation dialogue box saying like Fig 6 Click Continue Anyway button to proceed E PenMount P RS 737 Driver V1 0 0 1 Setup TO R O Pondount P3 RS 737 Driver V1 0 0 1 Setup a a Lermen Arenal El Choir Inia Labor Pleats nine the licores berri before nel alira Penhi Pl ASIA Drier Vio Chega the older meta to rela Panhu Pl REZA Drier 11 0 0 1 A f 3 The software you are installing has not passed Windows Logo testing to verify its compatibility with Windows lt P Tell me why Press Page Down bo see the rest of the agreeme
29. th other products 1 2 Projected Capacitive Touch Panel AMT provides various different sizes of standard Projected Capacitive touch panels from 3 to size larger than 15 Customers could find related PenMount controller for each PCI touch panel If the PCI touch is designed specially the related PCI control board might be different For any questions about connecting the control board to touch panel please check to your system manufacture 1 3 PenMount PCI Control Board PenMount designed various control boards for AMT projected capacitive touch panels For different size of PCI touch panel need to match with different PenMount Control Board Model RS 232 Touch Screen Size PM1100 e PM1200 n M AS o PM120 T PM1300A IA pmi4oo e e LARA Remark a ltis subject to be changed without previous notice b The Touch panel size might be supported by different PenMount control board if the touch panel is development based on special request 1 4 Drivers amp Utilities All of the PenMount PCI series control boards are bundled with software drivers and utilities that support the most popular hardware platforms and operating systems PCIMset is the initial setting utility for PenMount PCI control board series Users are able to adjust controller input interface touch panel position touch sensitivity and check firmware version through this software PenMount PCI drivers are not allowed to install or operate w
30. the readme file included in the driver folder Chapter 3 PenMount PCIMSet 3 1 The first execution of PCIMSet Extract PCIMSet zip to your hard drive and PCIMSet exe file can be found in the extracted folder Double click on PCIMSet exe for executing the program If you use RS232 interface please remove PenMount device driver or temporarily disable Fig 14 the PenMount PCI serial device in the Device Manager before executing PCIMSet program if you use USB interface there is no need to remove the device driver nor to disable the device The program can detect PenMount PCI controller automatically and show all application interfaces for adjustment Note When Com Port Selected window Fig 15 appears if you are using RS232 please select the Com Port and then click OK If the using port is USB please select either OK or Cancel If the window No PCIM Device Detected as Fig 16 shows it supposes to be PenMount PCI device that hasn t been connected to the PC File Action View Help Es mEH mR PRS 4 ryan PC ey PenMount PCIMSet 1 Computer 13 Disk drives E Display adapters es dc No PCIM Device Detected a 45 Human Interface Devices 05 HID compliant device 5 HID compliant device AP Version 1 33 3 Microsoft Input Configuration Device Fi m E Wij PenMount PCI Seri Update Driver Software C IDE ATA ATAPI contro IEEE 1394 Bus host con Uninstall Keyboards A Mice and other pointir amp
31. you will need to perform Threshold Adjust Fig 18 Do not touch the panel while Threshold Adjust is running Fig 19 Sensitivity Parameters Panel Size Common Sensitivity 1 15 Please wait Do not touch panel AP Version 1 33 PenMount e Gel Fig 17 Fig 18 Fig 19 3 2 2 Parameters Sensitivity Parameters panel Size Common a Reverse X and Y vane For reversing the X and Y axis operation it is required when ES a integrator need to rotate the touch panel Fig 20 T Singe Touch R5232 b Single Touch For switching between single and multi touch function Note The multi finger support depends on the O S For example in windows XP all the built in software in windows only support single touch If you need dual touch function in this system you need develop specific software for supporting dual touch function c Default All parameters will be reset to the factory default values d Edge Adjust Fig 21 will appear when execute Edge Adjust With this function you can adjust the left right up and down sides of the touch panel In some situation the touch sensing in the edge area might affect by mechanic design This function could improve the touch performance in the edge area If the edge area is difficult to touch please increase the value If the sensing points shift too much in the edge area please decrease this value For end user adjustment please
Download Pdf Manuals
Related Search