Home

#03039 RP-1716DR USER'S MANUAL

1. G eo 100Mbps File pe El 200Mbps Web Server 100Mbps Hub 4 Switch Operation 4 1 MAC Address Table and Learning The switch is implemented with a MAC address table where is composed of many entries Each entry is used to store the address information of network nodes on the network including MAC address port ID etc The information is the most important base to do packet filtering and forwarding When one packet comes in from any port the switch will learn the source address port ID and the other related information in address table Therefore the content of the MAC table will update dynamically Filtering and Forwarding When one packet comes in from any port of the switch it will check the destination address besides the source address learning The switch will look up the address table for the destination address If not found this packet will be forwarded to all the other ports except the port where this packet comes in If found and the destination address is located at different port from this packet comes in the packet will be forwarded to the port where this destination address is located according to the information of address table But if the destination address is located at the Same portas this packet comes in then this packet will be filtered Store and Forward Store and forward is one kind of packet forwarding methodology As a store and forward switch it will
2. attached client with no bandwidth congestion issue Store and forward switching mode promises the low latency plus eliminates all the network errors including runt and CRC error packets To work under full duplex 5 mode transmission and reception of the frames can occur simultaneously without causing collisions as well as double the network bandwidth The switch is plug n play without any software to configure and also fully compliant with all kinds of network protocols Moreover the rich diagnostic LEDs on the front panel provide the operating status of individual port and whole system For network connection The switch can use the following types of cabling m 10BASE T Category 3 4 or 5 UTP STP m 100BASE TX Category 5 UTP STP Category 5 cable is preferred to use with this product in structured wiring environments This will ensure correct operation of all ports at LOMbps or 100Mbps 2 2 KeyFeatures The switch provides the following key features Complies with 10BASE T specifications of the IEEE802 3 standard Complies with 100BASE TX specifications of the IEEE802 3u standard Sixteen RJ 45 ports for 100BASE TX and 10BASE T connectivity Supports NWay protocol for speed 10 100Mbps and duplex mode Half F ull auto detection Supports MDI MDI X auto crossover Supports full and half duplex operation on all ports Wire speed packet filtering and forwarding rate Store and forward architecture filters fragment amp CR
3. C error packets 6 Supports 8K MAC address entries and 128 entries of CAM 512KBytes buffer memory Supports extensive LED indicators for network diagnostics Internal universal switching power supply 100 240VAC FCC ClassA CE The Front Panel The front panel of the switch is shown as below 990000000 ig cg i cn 11 inch model mwa hace a dad Fe Sere jay Switch 19 inch model The auto negotiation feature of the switch allows each port of the device running at one of the following four operation modes 1 100Mbps full duplex 2 100Mbps half duplex 3 10Mbps full duplex 4 10Mbps half duplex Each 10 100Mbps port supports auto MDI X capability that is the port could connect either the PC or switch without any cable adjustment 2 3 1 System LEDs System LED indicators are located on the front panel for showing the operating status of the whole device 2 3 1 1 PowerLED This indicator lights green when the switch is receiving power otherwise it is off 2 3 2 PortLEDs Port LED indicators are located on the front panel for showing the operating status of each port 2 3 2 1 100M LED Every porthas a 100M LED Steady green indicates that the port is operating at 100Mbps If the LED is off the link speed is 10Mbps Link Act LED Every port has a Link Activity LED Steady green indicate
4. PRZEDSI BIORSTWO HANDLOWE EXPORT IMPORT HURT BURO HANDLOWE WARSZAWA ATEL ELECTRONICS 01 797 Warszawa 45 323 Opole ul Powazkowska 15 ul Zielonog rska 3 ELEC I R ork N ICS tel 0 22 669 10 11 tel 0 77 455 60 76 fax 0 22 669 11 60 fax 0 77 455 80 56 e mail custQatel com pl www atel com pl 03039 RP 1716DR USER S MANUAL 16 P 10 100Mbps NWay Switch User s Manual V2 0 CE Declaration of conformity This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 class A for ITE the essential protection requirement of Council Directive 89 336 EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limitations are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if no installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the in
5. Twisted P air Cable 3 1 3 2 Switch to Switch Connections with Twisted P air Cable 3 1 3 3 Network Application 4 Switching Operation MAC Address Table amp Learning Filtering and Forwarding Store and Forward Product Specifications Unpacking Information Thank you for purchasing the 16 port NWay switch Before you start please check all the contents of this package The product package should include the following One 16 port NWay switch One power cord Rubber foot and screws Rack mount brackets optional for 11 inch model User s Manual Introduction To 16 Port NWay Switch General Description The device is a powerful high performance Fast Ethernet switch with all 16 ports capable of 10 or 100Mbps auto negotiation operation NWay which means the switch could automatically negotiate with the connected partners on the network speed and duplex mode It is ideal for micro segmenting large networks into Smaller connected subnets for improved performance enabling the bandwidth demanding multimedia and imaging applications Moreover the 10 100Mbps auto sensing ability provides an easy way to migrate 10Mbps to 100Mbps networks with no pain Compared to the shared 10Mbps or 100Mbps networks the switch delivers a dedicated 10 100Mbps connection to every
6. it the right way up on a hard flat surface with the front facing toward you Locate a mounting bracket over the mounting holes on one side of the unit Insert the screws and fully tighten with a suitable screwdriver Repeat the two previous steps for the other side of the unit 6 Insertthe unit into the 19 rack and secure with suitable screws not provided 7 Reconnect all cables 3 1 3 Installing Network Cables After placing the switch on the desktop then we need to know how to connect the device to network 3 1 3 1 Station Connections with Twisted P air Cable Connect each station to the switch by a twisted pair straight cable 10BASE T or 100BASE T cables Plug one RJ 45 connector into a front panel port of the switch and plug the other RJ 45 connector into the station s network adapter 3 1 3 2 Switch to Switch Connections with Twisted P air Cable In making a switch to switch connection you could use any port to connect another switch with straight or cross over cable As all the ports support auto MDI X function so the connection is independent of cable type and using a straight cable to make a switch to switch connection is allowed 16 P Nway Switch 3 1 3 3 Network Application
7. ly use any of the features of this product simply by attaching the cables and turning the power on 3 11 Desktop Installation Locate the switch on the desktop and place the switch on a clean flat desk or table close to a power outlet Plug in all network connections and the power cord then the system is ready When deciding where to put the switch you must ensure E Itis accessible and cables can be connected easily a Cabling is away from Sources of electrical noise such as radios transmitters and broadband amplifiers gt Power lines and fluorescent lighting fixtures Water or moisture can not enter the unit Air flow around the unit and through the vents in the side of the case is not restricted company recommend that you provide a minimum of 25 mm clearance To prolong the operational life of your units m Never stack units more than eight high if freestanding m Do not place objects on top of any unit or stack m Do not obstruct any vents at the sides of the case Rack Mount Installation Rack mount kit is optional The switch may standalone or may be mounted in a standard 19 inch equipment rack Rack mounting produces an orderly installation when you have a number of related network devices The switch is supplied with optional rack mounting brackets and screws These are used for rack mounting the unit Rack Mounting the Switch in the 19 inch rack Disconnect all cables from the switch before continuing Place the un
8. s that the port has good linkage to its associated devices Flashing green indicates there is traffic transverses the port The following table is a summary of Port LEDs LED Operation 100M Link speed is 100 Mbps Green Link speed is 10Mbps Off Link Act The portis connected Green The port is transmitting receiving data Blinking Green If the port is connected but the Link Activity LED is dark check the following items 1 The switch and the connected device s power are on or not 2 The ports cable is firmly seated in its connectors in the switch and in the associated device 3 The connecting cable is good and with correct type 4 The connecting device including any network adapter is functioning 2 4 The RearPanel The rear panel ofthe switch is shown as below 11 inch model AC LINE 100 210VAC 50 60H7 1 0A Max 19 inch model 24 1 Power Connecting For compatibility with electric service in most areas of the world the switch s power supply automatically adjusts to line power in the range 100 240 VAC and 50 60 Hz Plug the female end of the power cord firmly into the receptacle on the rear panel of the switch Plug the other end of the power cord into an electric Service outlet then the power will be ready 3 Installing And Using 16 Port NWay Switch 3 1 Installing The 16 P ort NWay Switch The switch does not require software configuration Users can immediate
9. store the complete packet in the internal buffer and do the complete error checking before transmitting to the network Therefore no error packets will disturb the network It is the best choice when a network needs efficiency and stability 5 Product Specifications Standard Interface Cable Connections Network Data Rate Transmission Mode LED indications System Buffer Memory MAC Address Table Filtering Forwarding Rate Emission Operating Temperature Operating Humidity Power Supply IEEE802 3 10BASE T IEEE802 3u 100BASE TX RJ 45 x 16 NWay switching ports RJ 45 10BASE T UTP Category 3 4 5 RJ 45 100BASE TX UTP Category 5 Auto negotiation 10Mbps 100Mbps Auto negotiation Full duplex Half duplex System Power xl Port 100M Link Activity 512KBytes 8K entries and 128 entries of CAM 10Mbps 14 880pps 14 880pps 100Mbps 148 800pps 148 800pps FCC Class A CE 0 50 C 32 122 F 10 90 100 240 VAC 50 60 Hz 61RP 5416C 200
10. terference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into a different outlet from that the receiver is connected Consult your local distributors or an experienced radio TV technician for help Shielded interface cables must be used in order to comply with emission limits Changes or modifications to the equipment which are not approved by the party responsible for compliance could affect the user s authority to operate the equipment 2 Copyright 2002 All Rights Reserved Company has an on going policy of upgrading its products and it may be possible that information in this document is not up to date Please check with your local distributors for the latest information No part of this document can be copied or reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Table of Contents 1 Unpacking Information 2 Introduction To 16 Port NWay Switch General Description Key Features The Front Panel System LEDs Power LED Port LEDs 100M LED Link Act LED The Rear Panel Power Connecting Installing And Using 16 Port NWay Switch 3 1 Installing the 16 P ort NWay Switch 3 1 1 Desktop Installation 3 1 2 Rack Mount Installation 3 1 3 Installing Network Cables 3 1 3 1 Station Connection with

#03039 RP-1716DR USER'S MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents