User Manual Network connection and Mobics Dashboard (MIS
Contents
1. Adjustments apply for all characters after the adjustment If you wish to adjust a single character you need to enter an adjustment before e g 1 and after e g 1 this character so that the remaining text will have the standard alignment Because the resolution of the controller screen is limited h192 x v32 pixels there are also limitations on the number of characters which can be used in a translation Because different characters use a different number of pixels it is important to check both characters used and pixels used during the formulation of the translation Networking and MIS Manual M720 Dryer controller Manual version 1 If too many characters are used while inputting the translation the text box will show all the characters however they will no longer appear in the display simulation When the character or pixel limit for a translation is reached the boxes showing used remaining characters or pixels will turn red to indicate that a shorter formulation is needed Space characters use 1 character and 3 pixels Adjustment characters use one available character space Page 13 of 16 For some texts it may be necessary to change alignment from left to right This can be done with the button directly below the orange character alignment buttons English Characters EE Pixels t S S Ban d O 3 C C S H Some languages like for example Arabic are read and writ2. Emergency stop and safety sw Error frequency inverter Jog left button Jog right button Gas alarm input Input fire suppression Clean Filter warning Heater unit reset Status output Blower cleaning signal Blower WYE switch Drum motor direction left 3050000 Ka bk E E bt ks This input should be on when the door is closed A program can only be started if the door is closed When the machine is in a drying cycle or cool down cycle and FEI Ir l Lit um the door is opened the cycle will stop and a message will be displayed IF a cycle is Finished after drying and cooling down and the door is opened the controller will be ready For a new cycle S EI The diagram on the left shows the controller board and connections Status information is shown in the diagram and flashing lights next to the inputs and outputs indicates activity If optional extras humidity sensor or infrared sensor are installed and configured on a dryer the status of these will also be shown Select any item from the list of outputs inputs and ancillary devices on the right hand side of the screen to display further information in the text field below the list Networking and MIS Manual M720 Dryer controller Page 10 of 16 Manual version 1 2 4 Recipe parameters This screen is opened by clicking the icon in the main screen see 2 1 It provides options for managing recipes With it you can downlo
3. it will look similar to the screen above At the top is a row of buttons providing various functions see 2 4 1 On the left there is a list of all the recipes in the controller Select any of the recipes by left clicking the name in the list The rest of the screen is for editing recipe names On the far right there is a list of available character sets ticking the box next to each character set name adds these characters to the overview in the centre of the screen Above the character overview are two boxes showing stored on controller name above and edited name below The green box above this gives a representation of how the name will look on the screen of the controller See 2 5 1 for more details on how to edit recipe names 2 4 1 Function buttons These buttons give access to functions for exchanging data with the selected machine The machine name is shown in the top left on the title bar for the window Seen from left to right the buttons give access to the following functions EN Send recipe names y This resends modified recipe names to the selected controller Networking and MIS Manual M720 Dryer controller Page 11 of 16 Manual version 1 directory Send recipe data to controller This sends all recipe data for the selected recipe to the controller Save current recipe to file This saves all recipe data for the selected recipe to a file Send all recipes from directory to controller This loads all saved recipes in
4. MOBILS User Manual Network connection and Mobics Dashboard MIS software for Dryer Controller M720 Manual version v1 00 Networking and MIS Manual M720 Dryer controller Manual version 1 Document history Preliminary version v1 00 Created in February 2010 Networking and MIS Manual M720 Dryer controller Page 2 of 16 Manual version 1 Table of contents Reie Dinner 2 RRE EE 3 1 Connecting controllers in a network cece ceaeeeseaeeseeeeeseaeeseaeeesaeeesaeeeseaeeseaeesseaeesseeeesaes 5 1 1 Connection nee EE 6 2 Mobics Dashboard Management Information Gvsiem 7 CARMEN Re E EE H 281 Ee Mnes lS er rn ET EEEa E T 7 2 1 2 Operational data graph EE 8 2 13 FUNCHON ne 8 2 2 Settings Menu per machine 8 22a e Machine Name 2 steatosis SR espe Adee eerie at ees 9 2 2 2 COMMUNICATIONS Settings cecceeeeceeeeeeneeeeeeeeceaeeeeeeeeseaeeeeeeeeseaeeseaeeeseaeeseaeeseieeeseeesseeeeeaas 9 REEL EE 9 2 2 4 Automatic report Gring 9 2 2 5 Web server Settings ek 10 253 W O OVEIVIOW EE 10 24A RECIPE Paramelers c sic2eciscs Gaeta ene ete arte ns eee eae 11 215 Print Chant ccs tec ined Sie teat nt are ae eet E SEE eats weed eae 15 2 6 PANTO DON E E ASETI EEE tte eae stearate ote ee 15 Networking and MIS Manual M720 Dryer controller Page 3 of 16 Manual version 1 This page intentionally left blank Networking and MIS Manual M720 Dryer controller Page 4 of 16 Manual version 1 1 Connecting controlle
5. a given directory to the controller Save all recipes to directory This saves all recipes in the recipe parameter screen as individual files in a given 2 4 2 Editing Change recipe names wi Basics v Basic Latin v Latin 1 Supplement v Latin Extended A v Latin Extended B IPA Extensions Spacing Modifier Letters Combining Diacritical Mart Greek The characters which can be input using your keyboard are defined by the general settings of your computer This will vary depending on your location operating system language and keyboard settings To make inputting characters from other languages easier a long list of additional character sets have been included in the programme If you wish to make translations in Greek for example you can tick the box next to the Greek character set The additional characters will appear in the full list of available characters in Cyrillic the editing area of the main screen Armenian dee You can select as many additional character sets as you wish It is more practical Devanagari however to avoid the list becoming too long by only selecting the character sets Bengali you will really use Gurmukhi To edit the text place the cursor in j Characters 11 2 English SE DIE the lower of the two text boxes at Fran ais Pixels 57 150 the top left iA B IC D E F IG IH WJ IK IL MIN O ai Use the keyboard to input text PlaarRis ii uN Wk hy EI fk Special characters which are
6. ad one or more recipes from a machine on which it has been created edit the names and either upload the recipe s to other machines or save them as a backup on the computer Recipes cannot presently be created with this programme they must be created on a controller What this programme does is make it a much simpler task to share recipes with other machines manage and back up commonly used recipes TEST ID 1 COM3 Recipe 1 Recipe 2 Recipe 3 Characters vl Basics v Basic Latin Pixels V Latin 1 Supplement M Latin Extended amp 7 V Latin Extended B IPA Extensions Spacing Modifier Letters Combining Diacritical Mat O Greek Cyrillic Armenian Hebrew Arabic Devanagari Bengali Gurmukhi Gujarati Oriya Tamil Telugu Kannada Malayalam Thai Lao Tibetan Georgian Hangul Jamo Khmer Latin Extended Addition Greek Extended General Punctuation Superscripts and Subscr Currency Symhale Dec 000105 Hex 0069 5 D T Q zb bd 2 CG w H x 5 X Lay HEN ol o 5 lz v SSG KA HEH CHE 19 ek Pe R Ja j gt eD oN 1 2 e 1S10 E TO 8140 S 0 C TH OMO Dk CO Ps 3 ATMO m ONS AO S 2 DS CG gt Tk Te Or amp CO Ps sz Se coe Oe Die On bs Kw oO MnO Im OF amp Cl me Sr Is Ex ffr CS Ol OOS ToS OIF a Oc ax a ee OT TOO Boe o gt Or eo lo m oe SiS o I When the recipe parameters screen opens
7. ard 2 1 4 Function buttons General 4 These buttons give access to general functions for the Mobics Dashboard programme Seen from left to right the functions are as follows Add new machine This opens the machine setup screens see 2 2 Info This opens a window showing licensing information for the software No licence is required for the free version which is limited to a single machine 2 2 Settings menu per machine The settings menu is accessed by right clicking on a controller in the machines list Two consecutive screens provide options for individually defining each machine first screen and options for printing data or creating an online real time page for the machine which can be viewed in a web browser The programme allows charts and reports to be automatically generated for each machine cycle and sent to any printer attached to the computer by USB or UTP network Networking and MIS Manual M720 Dryer controller Page 8 of 16 Manual version 1 Machine Setup Pi Machine Setup Chart Settings Unique Machine Name Dryer 1 Automatic chart data reset Show temperature in celsius Machine type DryerM720 Automatic printing Communication Settings Automatic report printing Com port Template C Mobics Dashboard Templates Mobics Ad r Address controller GE Select Template Printer HP Color LaserJet CP4005 PCL 6_1 Select Printer Web server Settings Enable Web server Cancel Next Prev
8. er 11b 5347JR Oss The Netherlands www mobics ni info mobics nl Batch Report Dryer M720 GCL nz Drumttemteratuel Goal tempersture F Relatie Humidity F vo 44 20 14 25 4430 4435 44 40 4445 44 50 Batch time 0 35 16 Recipe name 12 50 C Automaat Batch times Messages during drying process 14 43 26 14 53 07 ished 15 9 2009 Dryer mas 14 18 42 15 9 2009 14 53 58 Batch temperatures Maximal goal temperature Maximal drum temperature Maximal garment temperature Example of report generated automatically by Mobics Dashboard software Networking and MIS Manual M720 Dryer controller Page 16 of 16 Manual version 1
9. h area 2 Networking and MIS Manual M720 Dryer controller Page 7 of 16 Manual version 1 Selecting a machine with the right mouse button gives access to the settings menu 4 below where the parameters of the machine can be modified A list of all configured com ports is given below the overview list of machines and lights indicate the presence of network activity for each port 2 1 2 Operational data graph 2 The graph shown in this part of the main screen is a representation of the activity of the machine which has been selected in the machines list It shows the trends for the current cycle of temperature humidity etc in addition to heater activity red blocks along the bottom edge and the phases through which the cycle has progressed In the case shown these are drying drying on humidity sensor optional module for the M720 cooling down ready anti crease drum rotates to prevent load becoming creased and door open load removed Below the graph a list of current alarms is given alongside an alarm history 2 1 3 Function buttons Selected Machine 3 These buttons give access to functions for whichever machine is selected in the machines list Seen from left to right the buttons give access to the following functions ES UO overview 2 3 below ag Recipe parameters 2 4 below with current active recipe shown D Print chart 2 5 below Print report 2 6 below S Copy graph to clipbo
10. ious Cancel 2 2 1 Machine Name Give each machine a unique name entered in the box at the top of the first screen and select the machine type from the drop down menu 2 2 2 Communications Settings First select the appropriate COM port from the drop down menu The menu will show all available COM ports on the computer select the one that was created when the M750 USB to RS 422 adapter was connected Finally you can select the controller address from the drop down menu This is the unique address station number assigned to each controller or I O extension board and is defined in the configuration settings of the controller For further details of how to configure the station number see the M720 Dryer controller user manual 2 2 3 Chart Settings Selecting the check box Automatic chart data reset will reset the chart data each time the connected machine starts a new cycle Selecting the check box Show temperature in Celsius will display all temperatures in Celsius By default temperatures are shown in Fahrenheit 2 2 4 Automatic report printing With this function activated a report is automatically printed after each drying cycle Select the check box Automatic chart printing to activate the function When the function is activated first select a template for the report Templates are stored in the Templates subdirectory of the main programme directory and a default template is included It is possib
11. le to make a template please contact your supplier for details Select the printer you wish to send the reports to from the drop down menu and specify the number of copies in the box provided for this Networking and MIS Manual M720 Dryer controller Page 9 of 16 Manual version 1 2 2 5 Web server settings Selecting Enable web server in the check box will turn on the web server built into the programme This generates a web page which shows the status of the dryer in real time The page can be accessed from any device which supports web browsing To view the web page on the PC to which the controllers are connected and which is running the Mobics Dashboard software type the following into the address bar of your browser http 127 0 0 1 8888 Mobics The above link is the web address of the local machine PC To view the page from other computers or devices you will need to use the web address for accessing the PC from a remote location Please contact your system administrator for details of your network configuration 2 3 VO overview This screen is opened by clicking the SS icon in the main screen see 2 1 It provides status information for each of the inputs and outputs of the selected controller in addition to power supply status and any possible error states TEST ID 1 COM3 M720 Dryer Air Flaw switch Input overload Input reserved Input reserved Rotation sensor Dir pressure switch Overheating input
12. not gt ai on the keyboard can be inserted a jo jc d je f jg hi KI mn jo by using the mouse to select them p a r is kt uw wx y GN i lH jj al from the list Ee gl BC OF le nk iz S SIE ai Pasting text copied to the S sg WM Ir 2 i 2 s ve a A A clipboard from other sources is AA AA AIC IE FE III DN also supported Both ctrl V and l6 666k l U U U OU Y b R l l right click Paste methods can be ie Fa ha SESCH E z SS z used a j ja ja jee fi ff ff i 6 ffi a ee ee A E ee i i To add more characters select additional character sets from the list on the right of the arrows by ticking the boxes Networking and MIS Manual M720 Dryer controller Page 12 of 16 Manual version 1 Frank ais D eo OOo KH Oo oc GO H i lo O P O DO ou Se D 72 GH Characters Pixels m ar Or w CH bh He 0 Some characters may appear out of alignment when displayed on the controller screen This can be corrected using the alignment adjustment arrows to the right of the characters list In the text edit box top left place the cursor before the character to be adjusted Click the left right up down arrow and select the appropriate number of pixels for the adjustment Space and adjustment characters are shown in yellow in the text edit box The display simulation shows how the change will look on the controller screen NOTE
13. rs in a network Both the controller and additional I O boards are fitted with an RJ 45 connector in order to allow connection to a network using the RS 422 protocol This also allows connection of the controllers to a PC A separate M750 RS 422 to USB adapter is available to facilitate this connection In combination with the Mobics Dashboard MIS software package see chapter 12 this connection option offers a number of possibilities to significantly enhance the way you use the controller Editing recipes and transferring them to from the controller s Retrieving batch data from controllers Automatic batch daily report generation and printing both locally at the dryers or centrally in the office Remote viewing of dryer status via internet web application can be viewed on almost any browser Controllers can be connected to a PC individually using one adapter for each controller as a network a single adapter connected to the PC with all controllers interconnected using UTP cable or a combination of these For correct functioning each individual controller and I O extension board must have a unique station number see section 6 4 3 item 11 A total of 199 unique numbers are possible Each M750 adapter installed on a computer must be assigned a COM port number With most Windows versions this happens automatically during installation when the adapter is connected to the computer Networking and MIS Manual M720 Dryer con
14. sed version is also available The licensed version allows up to 100 controllers to be monitored reports to be automatically generated and includes web server functionality for remote real time monitoring The Mobics Translator software enables creation and editing of user interface languages It is available free of charge from the Mobics website www mobics nl 2 1 Main Screen A full user manual for this software is available separately Here we give an overview of the main functionality provided by the software 2 Mobics M700 series Dashboard fe felix Sdt SDE GES Ga 3 SSB igor SI Dryer i 1 FER GCLnr2 f EI Dryer 12 1 IW Drum temperature V Target temperaturely Relative Humidity V vo Ce fa O SOD ryer 12 2 fet ft 2 Mach 17 1 mm comis Current alarms Alarm history 1 comz aoe Wait for start 10 08 22 10 08 43 Waiting for cycle restart 1 10 08 43 10 10 09 Wait for start Pa Comiz EE m com e 2 1 1 Machines list 1 This section of the main screen gives an overview of the machines which have been connected to the PC and entered into the programme configuration For each machine it shows the assigned name and icons indicate the status of the machine disconnected heating cooling ready etc Select any of the machines in the list and the relevant data from that machine will be shown in the grap
15. ten from right to left To input text for these languages click the text direction button below the text alignment button before entering the text All text entered will be saved with Characters 13 20 p oo Pixels 65 150 In order to enter text with direction left to right again the button should be clicked once more ojc o cm a se O Pe KM o oe OOH Sab Mi ag i CTS i I Networking and MIS Manual M720 Dryer controller Page 14 of 16 Manual version 1 2 5 Print chart This screen is opened by clicking the S icon in the main screen see 2 1 Allows printing of current graph to any printer installed on the PC with basic options to adjust the chart for readability g Print chart Orientation O Portrait Landscape Margins Sc 21 8 v d t Close Printer ETT ge 2 6 Print report Clicking the e icon in the main screen see 2 1 generates and prints a full report of the last cycle of the selected machine Reports are based around templates which can be custom created so allowing the customer to make reports in the format that suits them best and with company logo s etc Reports can also be generated automatically after each cycle This can be configured in the settings menu see 2 2 An example of a report is shown on the next page Networking and MIS Manual M720 Dryer controller Page 15 of 16 Manual version 1 Mobics BY Lauwersme
16. troller Page 5 of 16 Manual version 1 1 1 Connection methods Single M750 RS 422 to USB adapter controllers connected with UTP network This connection can be realised with less hardware but has the disadvantage that overall data transfer rate of each controller is limited by the fact that the PC will collect data from each controller in turn Multiple M750 RS 422 to USB adapters each connected to an individual controller or controller I O extension board combination This connection method obviously requires more hardware but will offer continuous data exchange between each controller and the PC Combinations of these methods are also possible For example different groups of dryers can be interconnected with UTP network with each group having a dedicated RS 422 to USB adapter for connection to the PC Networking and MIS Manual M720 Dryer controller Page 6 of 16 Manual version 1 2 Mobics Dashboard Management Information System There are two additional software packages available for use with the M720 dryer controller The Mobics Dashboard MIS software allows recipes settings and operational data to be transferred between a controller and a PC A free version of Mobics Dashboard Management Information System is available This version is limited to basic functionality and is intended for laundries and service personnel as a tool to assist in optimal configuration of each controller For full functionality a licen
Download Pdf Manuals
Related Search